From a few access points SSID
Hi all
I'll create a new WLAN id/identifier SSID in Cisco 4402 wireless controller and as soon as I did that create the ssid will be pushed to all access points, but I want to broadcast the SSID that at a few access points, is anyway we achieve this in the controller itself or WCS. Please let me know
Thank you
Hello
Yes, you can shape this traffic. His call to Cisco AP groups. You can simply consult the configuration for confi efforts guide. What is the code, you are on, if you are on 4.2 you can Overide WLAN.
I hope this helps...
Tags: Cisco Wireless
Similar Questions
-
On remote access points SSID broadcast
I'm deploying a Uniified Wireless Communication network that spans two location (Head Office and branch) using 1xWLC 4402 and 13 x 1252 APs. Is it possible to configure the access points to the branch to broadcast the ssid, which would not be released on the APs on the WLC seat.
Thank you
OLA
Hi, you could use "overwrite WLAN' to do.
Here the necessary instructions... to search "To substitute WLAN" in the document to get good paragraph...
http://www.Cisco.com/en/us/docs/wireless/controller/4.0/Configuration/Guide/c40wlan.html#wp1089232
-
How connect N600 router wndr3400v3 to another hotspot or wifi ssid access point
I want to connect to my router to an another ot hotspot or access point ssid to increase network range
I tried but not found any option
Help, please
Ok thank you
-
LAPN300 - the best configuration for 3 access points, while using the same SSID
Hi all
What is the best configuration for 3 x LAPN300 located in various places around my house of 3 floors, access points if I want just one SSID?
I did some initial research which suggests that I can use the same SSID on all three, as long as they are on different channels. 1, 6 and 11 for example. In theory, then, as I wander around the House the client machine must auto swap to the AP with the signal stronger.
What do you think? What is the best way or do, or could suggest you something else?
As an aside... If I decided to create a second SSID for the guests at home, I would also want to add wireless isolation to this SSID. How would that be managing the DHCP server on the local network? How would be asked to connect to the SSID has never get an IP if they have been isolated from other clients on the local network? Besides, how they see the router? The ANNUAL lets you specify exceptions to this isolation for this feature? Alternatively, as I suspect, is the right isolation feature isolate them from other WLAN, not the LAN clients customers?
I did some testing and configuration of the AP with the same SSID and security will do what you want. Don't worry about setting the channel because the auto channel setting works with these devices and automatically adjusts the spacing between the appropriate channels.
Recommendation of the VPN_user is what you need if you want to isolate the SSID comments from the rest of your network clients.
Isolation of SSID of the AP will guard only wireless devices to communicate with each other on the same SSID on which it is enabled.
-
Stor.E access point stops working after a few seconds
Bought a Stor.E wireless adapter and followed the instructions but after turn on the unit by connecting to USB power usage provides cables, access point WIFI disconnects after 4 or around seconds.
1. I connect to usb power
2. the indicator flashes in green and stays on
3. wireless light turns green and stay on, turns off after a few secondsManaged to connect using the mobile app several times, while its sequel, but given that the WIFI point disconnects, can't use it.
Any thoughts?
1. I connect to usb power
Stor.e wireless adapter must be connected to the power supply and the other end to the external HARD drive.
Then, you can use the application to access the wireless content.
-
My laptop was working fine yesterday, but when I started it today I get the message "Wireless association failed because Windows did not receive response from the access point or wireless router.
I can see my network and I can connect to the internet using my desktop pc, but just to make complicated I can't even connect to the network when I plug the ethernet cable into my laptop.
I think it might be a driver problem, but I have no idea how to solve this problem without access to the internet on my laptop.
I'm running Vista and my wireless router is an Atheros AR5009 809.11a/g/n
I need step by step instructions on this Yes please treat me like a fool!
Thank you
Laptop would not work at home thus concluded that it was a BT Broadband do not issue my driver (despite BT telling me the opposite last night)
After the call to a fantastic Lady in BT it's all fixed and thanks to Jack I now know a lot more on connecting wireless to my laptop!
-
Unique SSID to the autonomous access point
Hello
My question is that if I have one SSID on an autonomous access point while I use the vlan native too. I mean what's the best practice in this case, if the vlan wireless say 10.
Also I have to use the bvi-1 or I have to creat bvi another for this vlan?
Thank you
In my experience it's not a must to use native vlan.
No, you should use only one interface BVI.
Just like that:
Ter of conf
!
Dot11 ssid ABC
VLAN 10
Open authentication
Authentication-key wpa version2 management
WPA - psk ascii cisco123
Comments-mode
!
d0 IND
SSID ABC
encryption aes encryption vlan 10
!
D1 IND
SSID ABC
encryption aes encryption vlan 20
!
d0.10 IND
encapsulation dot1q 10
!
D1.10 IND
encapsulation dot1q 10
!
gig0.10 IND
encapsulation dot1q 10
!
int bvi1
IP addressConcerning
Remember messages useful rates
-
Access points dropping from top to bottom
I have anywhere from 5 to 20 points of access drop goes up and down all day on a total of about 200. I try currently to cross and understand why we our access points are conducting many issues and how I might be able to solve.
One of the newspapers I see often is:
AP "exp - p13,' interface '802. ' 11A ' controller ' 10.2.192.25 '. String passed to ' 44 ""60"due to 'None '. Energy interference before update is ' 0 'and after update is ' 0'. Noise before update is ' 0 'and after that update is ' 0'. Interference before update is ' 0 'and after update is ' 0'.
Is any way to determine what the cause of this?
The controller firmware: 4.2.130.0.
Model AP-AIR-LAP1242AG-A-K9
IOS Version 12.4 (10B) JA4
Sounds as if it was just the Radio Resource Management (RRM) on the controller. You can disable this if she is down to customers. Go to the wireless tab, look on the left and click on the 802. 11A / n or 802.11b/g/n dropdown. Then click on the drop down RRM, click Auto RF.
My advice is to change the algorithms of subpoena power and channel to "On Demand. You can call them to the need to maintain an optimal network. By default, it automatically calls the update every 10 minutes.
Give it a try and see if it helps. If this isn't the case, we can explore more.
-
installation of switchport lwapp running of multiple ssid access point
Hi all
When you set up a hotspot lwapp, must I trunk all the VLANS on the port to the ap? or do I only allow the vlan management for the access point? That is to say 1 vlan and normal access port?
see you soon
Carl
If it's a LWAPP AP, then the switchport should be an ACCESS PORT... It's just to get the IP to the AP, then the AP wil try to join the WLC... once that the AP has joined, the SSID and the rest through the LWAPP tunnel...
Concerning
Surendra
-
Unique to the multiple SSID and possible access point single channel?
Hello world.
I have a silly question.
Let say, we have three VLAN, vlan1, 2, 3 and they are mapped to the following wireless LANs:
VLAN 1 ssid1
VLAN 2 ssid2
Vlan3 ssid 3
AP - trunk - dagprogramm network.
Our access point has mobile devices in three local wireless networks, IE ssid1ssid2 and ssid3
Since the mode AP use half duplex, mobile devices need acknowledgement positive to ap they can send data, so once channel let channel 3 (assuming that 802. 11b is used) can be shared by all the devices in three local wireless networks.
My understanding is correct?
Thanks and a great weekend.
An access point = an associated action related channel and each ssid and the customer that one channel and the AP is essentially as a hub
concerning
Joe
-
How can I get my name from the access point?
Since I bought a modem Arris 228 G and spent my 2 wireless, printers Canon WIFI unable to connect at Optimum!
Canon said to contact my router creator (Apple Airport Extreme) for the name of the access point get return wireless, WI - FI printers.
Help, please.
W.W.
(Mac Pro 10.6.8)
The name of the access point is simply the name of the wireless network that provides AirPort Extreme.
You can see the name of your wireless network by clicking on the WiFi icon at the top of the screen of your Mac and by checking that the name appears.
There will be a check mark next to your wireless network name.. which is also known as a wireless access point.
It would be the same name that you had before... unless you have changed some settings on the AirPort Extreme.
-
Cannot connect to Internet access point except on a Jetpack from Verizon.
I am running Window 7 Home Premium. I can connect to the Internet using my Verizon Jetpack and nothing else. I tried to use my Verizon phone as a hotspot, I have a router Belkon 4. 1A and we tried through other points of access. It connects to the access point according to the plan, but it is XE offline to the Internet. I tried to update my drivers for wireless devices, and it is said that they are already updated. I can connect when I'm wired. When I check properties properties IPv4 and IPv6 are shoddy outside. Install is the only thing not frayed on. When click on install, I get an error: cannot add the requested feature. the error is: these data are incorrect. My wireless adapter is Realtek RTL8187SE Wireless LAN PCIE network adapter. Please help me I am so frustrated.
Hi Sylvia,.
I imagine the inconvenience that you are experiencing.
Here are some ways you can follow to resolve the problem:
Method 1:
Check out the link and follow the steps in the article:
Wireless and wired network problems
Method 2:
Flush the DNS and request a new IP address of your ISP server by following these steps.
a. click on start
b. click on run
(c) in the Run dialog box type cmd.exe and click OK
d. in the command prompt, type the following.e. ENTER after each new line.
ipconfig/flushdns
ipconfig/release
ipconfig / renew
outputMethod 3:
This problem may be caused by incorrect DNS settings. following these steps and check:
a. click "Start", enter "NCPA. CPL"(without the quotes) and press ENTER.
b. right-click on the connection you use for the local connection, and then click "Properties".
c. Click to select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.
d. in the Internet Protocol window, we will change the "Preferred DNS server" to 208.67.222.222
e. click 'OK' twice to complete the change.
If the problem persists, please repeat the steps and change the "Preferred DNS server" to 208.67.220.220.
Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.
-
Satellite L300 Wireless does not work in mode access point
Satellite L300 with built in wifi Realtek device.
Internet is coming from an external USB device, and I want to make wifi internal working as a router/hotspot/access point, just to connect with my cell phone.I try to create the ad - hoc network in Windows 7 and Linux Fedora.
New network is listed in the OS cmdlets, but no SSID appears on my laptop.Also tried with hosted network (virtual wifi adapter) and app named Connectify in Win7.
SSID appears, but is unable to connect or link broken after a few minutes without any data transfer.Now, I came to ask me for this built in hotspot wifi device support mode at all?
If so, is there a setting I'm missing?
Or some utility runs, to check if the device is broken or have a driver problem, or something...?I put t know who don't L300 you have exactly and can't say what WLAN card is inside but the audit model in Device Manager and try to find the specification exact Googling autour.
To be honest I really don t know if your problem has nothing to do with Toshiba directly.
-
Radio error 1140 series access point
We have recently been deployed 1142N access points along the
our campus and have experienced some problems with stability of connectivity.
It seems that at random times Radio 0 will descend and connectivity to anyone to kill
Active access point. By issuing a command to 'see the dot11 association', not
get a result at as such research:150 5-516-AP > sh dot11 association
802.11 client Stations on Dot11Radio1:
SSID [Berklee student]:
Unknown - auto Drv_Add_In 0.0.0.0 0026.xxxx.xxxx
Unknown - auto Drv_Add_In 0.0.0.0 9027.xxxx.xxxx
Unknown - auto Drv_Add_In 0.0.0.0 9027.xxxx.xxxx
Unknown - auto Drv_Add_In 0.0.0.0 9027.xxxx.xxxxWhile in this State, making orders for d0/d1 int show gives you the following results:
Dot11Radio0 is reset, line protocol is down
The material is 802.11n 2.4 GHz Radio, the address is 1c17.d3ca.82f0 (bia 1c17.d3ca.82f0)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802. 1 q Virtual LAN, Vlan ID 1., loopback not set
Type of the ARP: ARPA, ARP Timeout 04:00
Last entry 1d16h, 00:00:00 exit, exit hang never
Final cleaning of "show interface" counters never
Input queue: 0/1677/81485/0 (size/max/drops/dumps); Total output drops: 72073802
Strategy of queues: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bps, 0 packets/s
5 minute output rate 0 bps, 0 packets/s
119910815 package, 4144709374 bytes, 0 no buffer entry
Received 1084186 broadcasts, 0 Runts, 0 Giants 0 shifters
entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored
entry packets 0 with condition of dribble detected
165186574 packets output, 503099299 bytes, 0 underruns
19743 output errors, 0 collisions, 116 interface resets
unknown protocol 0 drops
0 babbles, collision end 0, 0 deferred
0 lost carrier, 0 no carrier
output buffer, the output buffers 0 permuted 0 failuresDot11Radio1 is up, line protocol is up
The material is 802.11n 5 GHz Radio, the address is 1c17.d37b.9a20 (bia 1c17.d37b.9a20)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802. 1 q Virtual LAN, Vlan ID 1., loopback not set
Type of the ARP: ARPA, ARP Timeout 04:00
Last entry 1d04h, 00:00:00 exit, exit hang never
Final cleaning of "show interface" counters never
Input queue: 0/1677/10511/0 (size/max/drops/dumps); Total output drops: 75923217
Strategy of queues: fifo
Output queue: 0/30 (size/max)
5 minute input rate 4000 bps, 6 packets/sec
5 minute output rate 0 bps, 0 packets/s
200792332 package, 999483950 bytes, 0 no buffer entry
Received 722359 broadcasts, 0 Runts, 0 Giants 0 shifters
entry 0, 0 CRC errors, frame 0, saturation 0, 0 ignored
entry packets 0 with condition of dribble detected
293761017 packets output, 4202490277 bytes, 0 underruns
6043 output errors, 0 collisions, 3 interface resets
unknown protocol 0 drops
0 babbles, collision end 0, 0 deferred
0 lost carrier, 0 no carrier
output buffer, the output buffers 0 permuted 0 failuresThe only way out of this state the AP should perform a reload/restart.
Once again this problem seems to be random but I had to connect to all daily from the AP
basis to ensure that they are all in place and working properly which is a pain! We have about 40
running and about 60 percent of 1142 have experienced this problem at one time or another. So far, I
have not found any pattern or record information that can direct me to root causes
Thus, any idea that you can provide would be a great help!Hello
Please open a case with us (TAC), help you... There are a few bugs that is...
Concerning
Surendra
======
Please rate the posts that answered your question or was useful
-
My Airport Time Capsule can act as a WIRELESS access point
Hello.
I brought a Time Capsule with my Mac Pro. It worked well since yesterday.
I have set up the time Capsule as a WIFI, bypass at my local network access point. There is a router (cable) works at home.
It's my Mac Pro AirPort Utility and my iPhone, my Time Capsule is displayed with an exclamation point saying "device not found". I can't connect to the disk on this subject by afp share, or smb. Time Machine function is gone too. He failed trying to connect to the share drive from another computer connected to the time Capsule by cable network.
But at the same time, WiFi works well.
I tried to recycle energy. Sharing disk will be available. But if I start the Time Machine backup, it will not be a few seconds.
Any idea?
Thank you.
There are several posts here related the issue.
Luckily, you have set up your new Time Capsule for Back to My Mac (BTMM)?
If so, the 'temporary' solution is to delete/disable the option of the CCMM, as follows:
- Run the AirPort Utility.
- Select the base and then station, select change.
- On the tab of the Base Station, go back to the section of my Mac at the bottom of the window.
- If you have entries here, select it and click then the minus sign "-" button to remove it.
- Click on update and allow the base station restart.
If you have not enabled CCMM, we have other options for you to try.
Maybe you are looking for
-
How to activate the webcam on the Satellite C660-C660D?
I can't get my webcam integrated for work on the Satellite C660D/C660. Should I turn on or download a driver? Help
-
Can I resell my iPhone Sprint once the contract is up?
Hello! I recently updated my iPhone 5S for a 6s under my contract with Sprint. So I now have an iPhone used 5s in very good condition and I'm looking to sell it. Given that my plan is currently using the 6s and 5s is is more used, can I sell it on eb
-
Iomega 3 years warranty is always worth anything?
http://www.iomegasupportforums.com/phpBB2/viewtopic.php?p=159907#159907 Because I found that the subject of the original forum the Forum of Iomega is now moderator only post, I'm forced to continue here. I will issue the retailer of lawsuits under th
-
Windows asks for a password when you try to access to the "view work group computers."
We are on a network. Main computer, that we can access through the receptionist connect you and access shared files on this computer. Computer from the receptionist, windows asks for a password when you try to access to the "view work group compute
-
Lack of email address on the new posts
Until recently, all new e-mails was the office name, address. Phone #s etc at the end of the message. He disappeared. How do I restart it?