Function USB does not start

Similar Questions

• SSD external via USB does not start by default

  Hello Apple community.

  I have a problem with my new external SSD. Given that the base model Mac Mini end of 2014 comes with a disk HARD 5400 RPM drive, I wanted to go to an SSD without having to tear the whole unit. I wanted to exhaust the option 'boot from USB' and I'm having a strange problem. I cloned my Mac to the new drive SSD and slapped in a box set of the speaker. I connected via USB and changed my 'startup disk' to use the external SSD drive. However, it does not start on this unit automatically. When I reboot and discovers the "boot manager" I see the USB being initialized automatically. After disconnection / re - plug the drive in, it appears as a boot option. Once it is initialized, everything works fine and I can boot into El Capitan without any problem using the SSD.

  I am trying to find a way that I can get the Mac to initialize the SSD to the boot upward and choose default. I don't want to have to re - connect the drive whenever I want to start on the SSD drive... Any help and suggestions are greatly appreciated!

  My equipment

  ===========================

  Model Base of Mac Mini (end of 2014)

  1.4 GHz Intel Core i5

  4 GB of DDR3 1600 Mhz

  OS X - El Capitan v 10.11.3

  240 GB SanDisk SSD more - connected via USB3.0

  What unit do you use for the SSD?

  Can you provide a link?

  If the SSD is delivered with a box to provide a link to that,

  How do clone you for the SSD? What app did you use?

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable, reinstall the OSX. Nothing shall be lost

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• K410 USB DOES NOT START

  I have Windows 8 64 bit on my K410 IdeaCentre and the start menu, when I press F12 at startup, does not recognize my Cruzer of Sandisk USB flash drive because it is not listed in the start menu. I have a Dell with Windows XP and my flash drive works fine so I know that the problem is not with my flash drive.

  Hi bobby_99,

  You can change the value of OS Optimized Defaults for other OS or disabled. Then insert your bootable USB key and press F10 to save and exit the BIOS.

  Let me know your results

  See you soon

• Satellite A660-186 does not start when the USB nano-receiver is connected

  Recently I bought a mouse a4tech g7-750 with the nano-receiver into usb port plug.
  After the nano-receiver is inserted into the USB before lighting, computer laptop does not start.

  Only the cursor is displayed, so that it is displayed before the screen with the ability to enter the F2 BIOS or select the F12 boot device.
  Without the nano-receiver laptop runs without problem.

  Any advice?

  Thank you much in advance.

  Hello

  During the POST (power on self-test) all parts laptop as RAM, motherboard (also of connected devices) is enabled.
  If a problem (compatibility problems, etc.) would be detected during POST, then the laptop would not initialize correctly.

  This mouse nano-receiver is unknown to me and I m not very well what s wrong with this unit, but I doubt that this problem is related to the laptop.
  I guess that the laptop starts properly with other devices connected to the laptop. right? Well well, in such cases, there s no question cell phone but the 3rd unit affect the functionality of the laptop.

• Flow 10 7 HP - Windows does not start, I can't get into recovery 8.1 because cannot boot from USB-HELP Please!

  Hi all, I'm new here!

  I am (excuse me: has) with a stream 7

  A few days ago, I tried to install Windows 10 TP renovation 8.1 with Bing. After a while of waiting, he managed, but unfortunately I have forgiven to in SSD Tablet hp drivers, thinking that they were not necessary. If the touchscreen, WiFi and all the other stuff has failed. After I've got collegated by OTG, a keyboard and a mouse, that I managed to use Windows 10.

  Try to install the drivers, my fault, I opened a .exe from Realtek (perhaps for audio), Tablet asked to reboot and after that I can't access Windows anymore.

  I tried to start Windows 8.1 from a USB key, but it does not start, the same even if I disable secure boot.

  With disabled bitlocker Windows gives this error

  

  In the start option, I set these settings

  

  I put the USB in this way:

  

  The stream does not consider the USB absolutely XD

  If I turn on again the secure boot Windows gives this error (which 99% is caused by the .exe I installed):

  

  Restart the flow some time with secure boot it goes in a menu (where touch screen works) where there are a lot of options to reset Windows, but none of them doesn't work. If I try to format in this menu it asks password for my account, but it does not accept the mine :/

  If I try to open the collection (from volume button when it starts less) it gives this message:

  

  Waiting for relief,

  Thank you for your patience!

  @fotogruia in my case, the indicated operating system was windows 10 and as I wrote it has worked well. Good luck!

• Satellite A30 does not start with the USB device connected at boot time

  Hello

  I have a Satellite A30 and sometimes it does not start.
  After turning on, not even the BIOS starts.
  even if sometimes the BIOS starts, but the OS does not load.

  I figured out that its related to USB devices connected at boot time.
  If no USB devices are connected, it starts without a problem.
  Even if the start-up is suspended, as soon as you unplug start it BIOS USB devices.
  Its ok to connect USB devices later, once the system has started.
  I disabled "removable devices boot" and "network startup."
  just in case, but it makes no difference.

  BIOS is version the most recent (1.70) and it comes up with all kinds of USB devices.
  printer, mouse and (self-powered) external USB hard disk.

  Is this a known issue?
  There is no known workaround solution?

  Hello

  I put t know why this happens, but it has to do with the BIOS.
  The same thing happened on my old laptop. I couldn't start my unit while the USB printer has been turned on and connected.
  The only solution is to disconnect the external USB device during the boot process.

  RSY you should check if the order of boot in the BIOS has been on the HARD drive first.

• Satellite C660 does not start on disc or USB

  My Toshiba Satellite C660-DSC0QE app, BIOS version 1.80, will not start Windows more - it just goes to the dreaded black screen with white cursor.

  I tried a system Win 7 recovery disk, a USB with software from Kaspersky on her recovery and even a full Win 7 installation disc, and it does not start at one of them.

  The boot order is set correctly, (optical drive or USB port) devices are read, but their initialization never actually in them - there is an obscure error message, or it acts like they weren't there at all.

  The obvious answer to these forums seems to be disable secure boot mode and then switch the to the CSM UEFI boot mode. Easier said than done - the menu options don't exist at all in my BIOS/CMOS screens.

  Finally, I see no way in the instructions to get a BIOS update occur without being already in Windows on the PC - http://aps2.toshiba-tro.de/kb0/HTD9502M10000R01.htm I'm assuming that the BIOS version 2.00 would have these options.

  Any help gratefully accepted!

  Hello

  I assumed that you have a white blinking cursor in the upper left corner.
  Is this correct?

  These symptoms appear where the system can not find a boot device (HARD drive) or memory problems (RAM module).

  First of all, you said that you have UEFI / CSM boot mode in the BIOS settings.
  So I m asking you what parameters of start mode appear in BIOS exactly?
  Find you these settings in the right area?
  Usually, you should have an area (tab) called security in the BIOS.
  In most cases, you will find a safe boot option, but the Satellite C660 does not support this option because it s too old.
  But the startup mode (UEFI /CSM) should be available in the BIOS. Check the settings in the BIOS of the system area

  Anyway, as I said above; It could also be a memory problem, so I recommend you to check if the memory is OK.

• Laptop does not start with the connected usb device

  Hello
  Voila, I have a Sp6100 Pro Satellite, when I try to start whith a usb printer is connected, the laptop does not start. I have the latest version of the bios 1.90.

  THX,
  Barzot @+.

  Hello

  What you mean with start won t at all? Is there any kind of reaction if you press the power button / stop?

• the inventory of VMware service does not start, the wrong function, bad sql server port

  I've migrated vcenter SQL database to a new server after this KB

  https://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 7960893

  but now most of the vcenter services does not start cause of according to the inventory service.  I see service log of inventory which is the problem, it tries to connect to SQL Server by default, 1433 port, but my SQL server instance is listening on a different fixed port, I don't want to change.  Where can I configure the inventory service we another port of SQL Server?  According to a KB related to the above, it is possible to do

  https://KB.VMware.com/selfservice/search.do?cmd=displayKC & docType = kc & docTypeID = DT_KB_1_1 & externalId = 2033516

  but unfortunately I have vcenter 6 and the instructions above do not seem to apply, I can't even find ssocli, the mentioned folder structure does not exist on my installation

  
  Thank you.

  I solved this.  Despite what has been reported in the newspaper the issue was not the port.  The new database is a named instance, the connection string for vcdb.properties, he entered as the server name = hostname\instancename in fact, it is necessary to use two slashes return hostname\\instancename :-/

• MacBook does not start without warning, please help I'm losing my mind

  MacBook pro froze performs a simple operation. Got the wheel turns and could not enter the finder, etc. Did a hard reboot. Now the computer does not start. I get the apple journal and the bar for a minute or two and then a zero symbol IE forbidden - a circle with a line through it.

  Surprisingly, it is less than two months after a similar disaster where the computer would not suddenly start. In this case, I was able to get repaired the program apple logic board (the problem was compatible with the congenital fail GPU result).

  Incredibly this time the macbook seems to be in even worse shape. I don't get anything useful from the startup keys.

  cmd R - take me in a gray screen no symbol

  D - no symbol grey screen

  option D - it took a while but eventually I got to choose the network, then it seemed to freeze on the globe

  option - strangely this brings me to a screen asking me to choose the wireless network, but it does not all networks in the box. weird - this happens even with a simple bootable usb key

  option cmd R - annoys me to the world, but the world does not revolve

  T - puts me the screen of the target disk, but the disk is unreadable from another computer

  cmd S / cmd V - gives me a code screen and then freezes

  Shift - takes me to zero cross again

  C - think for awhile, but let me on an undefined gray screen

  (I need some advice on the start-up of the thumb. Pressing C should force the startup of the thumb. I did an inch bootable with el capitan. However, I am not convinced that my thumb works on a functional mac either - I just can't get a macbook functional 2009 to start the boost by pressing C, although it starts from the thumb if I press option and go through the menu. Weird.)

  Help, please. Urgent need to use the computer and access the data on it.

  Even if you have just a few ideas that would be useful.

  Can I assume that you have a 2009 MBP?

  You have your data backed up?

  Have you tried SMC and NVRAM resets?

  https://support.Apple.com/en-us/HT201295

  https://support.Apple.com/en-us/HT204063

  Have you tried a secure boot?

  https://support.Apple.com/en-us/HT201262

  Take our installation disc and use the one with the Apple Hardware Test instructions on it and run the original test.

  Note that an error free AHT is inconclusive.

  Ciao

• 8060 cm does not start, but I think that number key may be stuck!

  Hello

  One of my machines had problems and I managed to get back to factory default and now it will only fuel but does not start (it may be the mode of PMS, but not sure).

  It gives me the opportunity to connect, but as soon as I do a load of asterisks appear in the box constantly as if a button is pressed, do not know if a button is stuck, I see not one, but that's the only explanation I can think.

  I have actually managed to type the password for the service the other day, because it doesn't have AutoFill, but I was so surprised and thought it was settled I started and I tried again, but now it will not happen again...

  Any ideas?

  Concerning

  Andy

  You cannot use the USB without the functional printer, the main firmware is to put the machine mode of loading the firmware and help push the CDFT-L firmware, this should be a low-level operation that can be done even if the two hard drives are erased.

  The system has a base charger for this OS, I you sent the link of the CDFT-L then maybe if you can connect up to on this, you will be able to push the firmware.

  If you have a hard drive with the operating system and then when he put system will check and the firmware for the 2nd disk of mirror as a back up.

  It might be possible that you could take a hard drive on your 2nd 8060 and put a new, check its load to the top and everything works, then put that hard drive in this, see if it recognizes the problem and auto load the blank disc?

  I'll be honest, I don't remember if I did that, I recall messing about with hard drives and firmware but it's been a few years.

  In theory, it would load the firmware is programmed for automatic formatting and configure erased readers, if that does not work then you may need to change the serial number etc, but that shouldn't be hard.

  I would not use a car of this machine in the other, I would watch a disc blank, just in case there is anything on the old disk that is the problem? Maybe I'm just paranoid but if I tried this I would get a blank disc, install it in the printer and then continue if everything was fine.

  Tag readers with a pen so that you know what are the components that we have mixed all readers in the room during the training.

• Find product key Windows 8 on a computer that does not start

  I bought a laptop Lenovo, a little over a year and all of a sudden, he started a loop when I try to turn it on. The computer seems to want to start with the Lenovo logo and then I get a blue screen with an irritating "your PC has encountered a problem and needs to restart." We are only collecting the error information and then we'll restart for you. : ("message and then the computer restarts and does it again and again and and more.")

  I brought my friend who is a technician and he said that I need the product key Windows 8 to create the Recovery Disk/USB. So I checked the area in which my laptop has been delivered to and there is no product key is located. Is it possible to find even if my computer does not start? I can access the configuration screen, but I can't find anywhere here either.

  Any help with this would be really appreciated.

  Thank you

  LUN

  With Windows 8, Microsoft changed stickers that have the product key that the user must type in during the installation of the operating system of new embedded BIOS product key. The idea is that by eliminating the tile, you eliminate one of the easiest ways for nefarious users get a legitimate product key. The sticker also eliminating product key removes any concern that the vignette could get damaged while at the same time eliminating the long and irritating the process of typing in various letters and numbers in the installation of the operating system.

  If the user has to reinstall the operating system on a computer with Windows 8, the installation process automatically captures key software product of the motherboard BIOS without input from the user. This means that these stickers familiar windows product key will no longer appear on Windows 8 computers.

  You must use the recovery partition to reinstall Windows 8, if its not functional, you should ask a Lenovo recovery media:

  http://www-307.IBM.com/PC/support/site.WSS/document.do?lndocid=MIGR-4HWSE3

  Computers laptops Lenovo include a function called the Lenovo OneKey Recovery button, which is used to boot into the recovery environment and to reinstall Windows.

  If this does not work, contact technical support

  replacement of http://www-307.IBM.com/PC/support/site.WSS/homeLenovo.do and demand

  See also:

  http://support.Lenovo.com/en_US/downloads/detail.page?docid=HT076024

• VM does not start after that ESXi was replaced by version 6

  Hi all

  
  

  I ran a scary problem after replacing my VMware ESXi version 5.1 to version 6.

  
  

  My server is an Areca RAID controller which is supported by version 6 default. Yes, after installation (clean installation) 6 ESXi on a key USB internal drive, everthing seem good. It shows my store of data stored on my RAID controller and I can see the content, (see attachment, image of my data store) including my VM file - SBS2011.vmdk.

  
  

  I'm not a highly qualified VM pro, but the hard (about 40GB) file must contain my full Windows environment (Windows 2011 server).

  
  

  Have access to my data store on my RAID controller and access to the original .vmx file, everything seems fine. Make a right click of the .vmx, add to the inventory and I'm ready to go... but... it does not start.

  
  

  It shows a resource error, not this additional information. My feeling is that there is something wrong with the location of the Swap, because it looks like the place to swap is located outside the VM storage location (hard). This is what looks like my .vmx:

  
  

  It is not stored on my hard ' / vmfs/volumes / 512 b 5271-cb39b672-c198-001e676870c7 /! It points to a different location.

  
  

  (File VMX also downloaded with this post)
  

  
  

  No I have two question. What would be the cause of this problem, not able to start the virtual machine?

  
  

  Second question. Perhaps a solution: delete all files in my store of data, except the VM-SBS2011 - flat hard file, create a new virtual machine on my server, using an existing drive (showing my VM-SBS2011 - flat hard), I'll be able to boot my virtual machine? It will create a (work) .vmx file to the cool address? There where no snapshots exist when I close my Windows OS down the last time. I lose all the data? Help, please!

  
  

  Currently, I download the full content (all files) of the database on my local computer as a backup. I hope that my hard file will be sufficient.

  
  

  I'm really grateful for your help!

  
  

  . Encoding = 'UTF-8 '.
  config.version = '8 '.
  virtualHW.version = '8 '.
  pciBridge0.present = 'true '.
  pciBridge4.present = 'true '.
  pciBridge4.virtualDev = "pcieRootPort"
  pciBridge4.functions = '8 '.
  pciBridge5.present = 'true '.
  pciBridge5.virtualDev = "pcieRootPort"
  pciBridge5.functions = '8 '.
  pciBridge6.present = 'true '.
  pciBridge6.virtualDev = "pcieRootPort"
  pciBridge6.functions = '8 '.
  pciBridge7.present = 'true '.
  pciBridge7.virtualDev = "pcieRootPort"
  pciBridge7.functions = '8 '.
  vmci0. Present = 'true '.
  hpet0. Present = 'true '.
  NVRAM = "VM - SBS2011.nvram.
  virtualHW.productCompatibility = "hosted".
  powerType.powerOff = 'soft '.
  powerType.powerOn = "hard."
  powerType.suspend = "hard."
  powerType.reset = 'soft '.
  displayName = "VM-SBS2011.
  extendedConfigFile = "VM - SBS2011.vmxf.
  floppy0. Present = 'true '.
  numvcpus = "4".
  cpuid.coresPerSocket = "4".
  scsi0. Present = 'true '.
  scsi0.sharedBus = 'none '.
  scsi0.virtualDev = "lsisas1068".
  memsize = "12288.
  scsi0:0. Present = 'true '.
  scsi0:0. FileName = "VM - SBS2011.vmdk.
  scsi0:0. DeviceType = "scsi-disk" hard
  IDE1:0. Present = 'true '.
  IDE1:0.clientDevice = 'TRUE '.
  IDE1:0. DeviceType = "atapi cdrom.
  IDE1:0.startConnected = 'TRUE '.
  floppy0.startConnected = "false".
  floppy0. FileName = "".
  floppy0.clientDevice = 'true '.
  ethernet0. Present = 'true '.
  ethernet0.virtualDev = "e1000e.
  ethernet0.networkName = 'network of the VM.
  ethernet0. AddressType = 'generated '.
  chipset.onlineStandby = "false".
  disc. EnableUUID = 'true '.
  guestOS = "windows8srv-64.
  UUID. Location = "56 4 d fe 63 9 b 1 has c6 - ba b 0, 00 e8 6f 3rd 80 e8 7A.
  UUID. BIOS = "56 4 d fe 63 9 b 1 has c6 - ba b 0, 00 e8 6f 3rd 80 e8 7A.
  VC. UUID = "6th 52 2d 21 82 34 04 - c8 18 19 67 f8 67 c3 a5 4 d.
  Snapshot.action = 'keep '.
  SCHED. CPU.min = '0 '.
  SCHED. CPU. Units = "mhz".
  SCHED. CPU.shares = 'normal '.
  SCHED.mem.min = '0 '.
  SCHED.mem.shares = 'normal '.
  scsi0.pciSlotNumber = "160".
  ethernet0.generatedAddress = "00: 0C: 29: 7 a: e8:80.
  ethernet0.pciSlotNumber = '192 '.
  vmci0.ID = "1048242304".
  vmci0.pciSlotNumber = "32".
  cleanShutdown = 'TRUE '.
  Replay.Supported = "FALSE".
  sched.swap.derivedName = ' / vmfs/volumes/512b5271-cb39b672-c198-001e676870c7/VM-SBS2011-snapshots/VM-SBS2011-6cbed3a5.vswp '.
  Replay.FileName = «»
  scsi0:0. Redo = «»
  pciBridge0.pciSlotNumber = "17".
  pciBridge4.pciSlotNumber = "21".
  pciBridge5.pciSlotNumber = "22".
  pciBridge6.pciSlotNumber = "23".
  pciBridge7.pciSlotNumber = "24".
  scsi0.sasWWID = "50 05 05 63 9 b 1 a 6f c0.
  ethernet0.generatedAddressOffset = '0 '.
  VM. GenID = "5456487432926317901."
  vm.genidX = "901288717606574007".
  hostCPUID.0 = "0000000d756e65476c65746e49656e69".
  hostCPUID.1 = "000206d70020080017bee3ffbfebfbff".
  hostCPUID.80000001 = "0000000000000000000000012c 100800.
  guestCPUID.0 = "0000000d756e65476c65746e49656e69".
  guestCPUID.1 = "000206d700040800969822031fabfbff".
  guestCPUID.80000001 = "00000000000000000000000128100800".
  userCPUID.0 = "0000000d756e65476c65746e49656e69".
  userCPUID.1 = "000206d700200800169822031fabfbff".
  userCPUID.80000001 = "00000000000000000000000128100800".
  evcCompatibilityMode = "FALSE".
  vmotion.checkpointFBSize = "4194304".
  softPowerOff = 'TRUE '.
  tools.syncTime = "FALSE".
  bios.forceSetupOnce = "false".
  IDE1:0. FileName = "".
  bios.bootDelay = "5000".
  snapshot.redoNotWithParent = 'True '.
  unity.wasCapable = "FALSE".
  tools.remindInstall = 'TRUE '.
  workingDir = "/ vmfs/volumes/512b5271-cb39b672-c198-001e676870c7/VM-SBS2011-snapshots".
  fileSearchPath = "/ vmfs/volumes/512b5271-cb39b672-c198-001e676870c7/VM-SBS2011-snapshots;.»
  checkpoint.vmState.readOnly = "FALSE".
  checkpoint.vmState = «»
  scsi0:1.present = 'TRUE '.
  scsi0:1.DeviceType = "scsi-passthru.
  scsi0:1.filename = ' / vmfs/devices/genscsi/naa.5000878000000000 '.
  scsi0:1.allowGuestConnectionControl = "FALSE".
  SCHED.scsi0:0.shares = 'normal '.
  SCHED.scsi0:0.throughputCap = 'off '.
  scsi0:0.mode = "persistent".
  scsi0:2.present = "FALSE".
  sched.swap.hostLocal = "disabled".
  

  I copied the file-VM in VMWare ESXi 5.5 on another data store (more old HP SAS) server en guess what... it's starting! So for now I'm back in business. It seems that there is something wrong with the original server, because my hard file appears to be damaged otherwise it would not start on my old good spare HP server...

  I still wonder what the hell happened after I replaced the internal drive of hypervisor type USB and installed ESXi 6 on a cool USB. I got in the RAID array. Now, even when I start the server of origin with it's original ESXi 5.1 USB (intact), I got the same error when you try to start the virtual machine. Is thinking there's something wrong with the RAID array but I can access the database on the RAID array and (after you move the content to another VM machine) all files are very well run smooth on the other server. Kill me.

  Any ideas?

• iMac does not start after 10.11.6

  Since the 10.11.6 patch my IMac does not start with my hub plugged.

  Everyone

  I assume you mean a USB hub? What does do when it's plugged in? It starts successfully when the hub is not plugged? If so, I would say that something is wrong with the hub or there is a problem with the port it is plugged or something plugged into the hub.

  Try to plug it into a different USB port on your Mac.

• 2006 iMac does not start. Help restore

  I have an Intel iMac core duo with iSight and built in disk drive around 2006. It does not start.

  When I turn on, it sounds and passes to the gray screen with the apple logo and a progress bar or a spinning wheel. Then he stops down. I tried all the troubleshooting and nothing works. In addition, I don't have the disks that originally from cane with the computer. So I can't make a diagnosis of the hardware. (Unless someone is willing to sell me their album hehe).

  This problem happened to me in 2012. I had a friend restore the computer to empty the hard disk, then boot from the snow leopard disc and reinstall everything. It worked like a charm.

  In 2013, a disc is stuck in the drive. I have troubleshooted only and nothing has worked. I assumed that the drive is dead and has continued to use the computer without worrying about that. Then, in 2014 someday when I restarted, the disk jumped! I never tested the drive then because I was afraid of another stuck disc. Then, the computer is dead again as he did in 2012.

  SO I know what to do. I need to wipe the hard drive and start over. However, I didn't have a drive. So, I bought one on eBay. When I insert it, the computer enters the disc. I can hear the mechanics works. It ejects even properly. However, I can't boot from the drive. When I start the iMac by pressing option, I don't see the Macintosh, no disk drive.

  My hard drive died? If so, a USB dvd drive would work? If USB does not work, how can I replace the drive?

  Is it possible that I bought a drive bad or fake software and that's why I can't boot from the dad?

  Please help in some way!

  Try a boot sure try safe mode if your Mac does not end commissioning - Apple Support