GBA using AD authentication

Similar Questions

• http using aaa authentication when Ganymede server is down

  I installed AAA using Ganymede and everything works well except for authentication http through a browser or a network Assistant when the RADIUS server is down. For console and telnet connections, the default authentication line when Ganymede is out of service.

  AAA new-model

  AAA authentication login default group Ganymede + line

  AAA authorization exec default group Ganymede + authenticated if

  AAA accounting update newinfo

  AAA accounting exec default start-stop Ganymede group.

  only AAA 0 default stop accounting controls group Ganymede +.

  only AAA 1 default stop accounting controls group Ganymede +.

  accounting AAA commands default 15 stop only Ganymede group.

  !

  aaa IP http authentication

  !

  radius-server host 10.161.161.20

  111111 radius-server key

  It must be something with the fact that on http or ANC, it connects to the router at level 15, but I have played with all sorts of orders of different authorization and cannot operate.

  Paul

  What you want to do for authentication if the RADIUS server is down? For telnet and console access you can use the line as a backup method because it is possible to configure a password for the line on the console and vty ports. Which type of backup method you want for HTTP? The one that seems most logical to me would be to a local authentication in order to cover the situation where the server is down.

  To use local authentication, you must do the following:

  -create a definition of the local user (maybe more if you need extended security).

  -specify a special method for authentication of the aaa.

  -specify that http, using the special method.

  The configuration might look like this:

  password user tech1 tech1

  AAA authentication login http_auth group Ganymede + local

  IP http authentication aaa - authentication of the connection http_auth

  Or you can decide to use the secret to activate (or password that is configured in office). The config might look like this:

  AAA authentication login http_auth group Ganymede + activate

  IP http authentication aaa - authentication of the connection http_auth

  If you want a different backup method, let us know what it is and we'll see how it could be implemented.

  HTH

  Rick

• Local use and authentication AD with ACS 5.6

  I have an ACS 5.6 unit configured to use AD authentication for my default network access and rules. It works very well.

  I tried to implement some features, put them in a group and give only locally defined ACS to users access to these devices.

  Problem, after you have created the local accounts on ACS creates a group of local identity, and trying to authenticate with a camera, I always get "object not found in the identity store.

  Is there a way to have the hybrid authentication like that? How do we?

  Hi Colin,

  One thing that comes to mind is "sequence of identity store. Ensure that you have "internal users" listed in there otherwise that demand would never be mapped against the internal users.

  I also want to double check the source of identity under default device admin or any service that you created. Ensure that internal users.

  Take a look at the document below for more details on the identity store sequence.

  https://supportforums.Cisco.com/document/103901/ACS-5x-identity-store-se...

  Kind regards

  Kanwal

  Note: Please check if they are useful.

• How to save the password encrypted in the database using database authentication (weblogic server)

  Hi Experts,

  JDEV version 11.1.1.7.0

  I have a usecase where I use database authentication in my Application.

  However if I save the module to record user password. Its economy without encryption. Can U suggest how can I do this

  Thank you

  Roy

  Please see

  https://docs.Oracle.com/CD/E16162_01/user.1112/e17455/dev_secure_apps.htm#OJDUG1168

• Ask about the segregation of database access by using the authentication of the os in the windows environment

  Hello

  I have a question about the segragation of database access using authentication of the os (like sqlplus "/ as sysdba") in the windows environment. Let me briefly explain my requirement: -.

  Assume that you have two DBA viz DBA1 and DBA2 and 4 resideds of databases in a windows server say A, B, C and D.Now I want to configure it in a way if DBA1 opens a session on the server then it may connect to the database A and B using only OS and DBA2 authentication can connect to database C and D only use OS authentication.

  Please let me know how to configure for this requirement.

  Version of the database is 11.2.0.3

  Hello

  This doc is 11.1 but I guess it's the same in 11.2 roles on Windows and administering external users

  You create a group ORA_SID_DBA and doing it this way - in recent years I have done but it used to work ok...

  See you soon,.

  Harry

• Microsoft OLE DB provider for ODBC Drivers error '80040e14"error using DW authentication level

  Hello

  I use Dreamweavers authentication of users to log users of in and everything works fine until I have try to use the 'levels '.

  I get the following error after trying to login;

  Microsoft OLE DB provider for ODBC drivers error '80040e14'

  [Sybase] [ODBC driver] [Adaptive Server Anywhere] Syntax error near 'group' on line 1

  /Coding/test_login.asp , line 29

  
  

  My code is as follows

  
  

  "< %@LANGUAGE="VBSCRIPT "CODEPAGE ="65001"% >

  <!-file = "Connections/Conn_PSCRM_Demo.asp #include" - > "

  < %

  ' * Post the request to connect to this site.

  MM_LoginAction = Request.ServerVariables ("URL")

  If <>Request.QueryString "" then MM_LoginAction = MM_LoginAction + "?" + Server.HTMLEncode (Request.QueryString)

  MM_valUsername = CStr (Request.Form ("usercode"))

  If MM_valUsername <>"" then

  Dim MM_fldUserAuthorization

  Dim MM_redirectLoginSuccess

  Dim MM_redirectLoginFailed

  Dim MM_loginSQL

  Dim MM_rsUser

  Dim MM_rsUser_cmd

  MM_fldUserAuthorization = 'group '.

  MM_redirectLoginSuccess = "quote - search.asp.

  MM_redirectLoginFailed = "no_access.asp".

  MM_loginSQL = "SELECT usercode, epros_password.

  If MM_fldUserAuthorization <>"" then MM_loginSQL = MM_loginSQL & "," & MM_fldUserAuthorization

  MM_loginSQL = MM_loginSQL 'from DBA. [user] WHERE usercode =? AND epros_password =? »

  Set MM_rsUser_cmd = Server.CreateObject ("ADODB.Command")

  MM_rsUser_cmd. ActiveConnection = MM_Conn_PSCRM_Demo_STRING

  MM_rsUser_cmd.CommandText = MM_loginSQL

  MM_rsUser_cmd. Parameters.Append MM_rsUser_cmd. CreateParameter ("param1", 200, 1, 255, MM_valUsername) ' adVarChar

  MM_rsUser_cmd. Parameters.Append MM_rsUser_cmd. CreateParameter ("param2", 200, 1, 255, Request.Form ("password")) ' adVarChar

  MM_rsUser_cmd. Prepared = true

  Set MM_rsUser = MM_rsUser_cmd. Run

  If not MM_rsUser.EOF or not MM_rsUser.BOF then

  "correspondence of username and password - this is a valid user.

  Session("MM_Username") = MM_valUsername

  If (MM_fldUserAuthorization <>"") then

  Session("MM_UserAuthorization") = CStr (MM_rsUser.Fields.Item (MM_fldUserAuthorization). Value)

  On the other

  Session("MM_UserAuthorization") = «»

  End If

  If CStr (Request.QueryString ("accessdenied")) <>"" and true then

  MM_redirectLoginSuccess = Request.QueryString ("accessdenied")

  End If

  MM_rsUser.close

  Response.Redirect (MM_redirectLoginSuccess)

  End If

  MM_rsUser.close

  Response.Redirect (MM_redirectLoginFailed)

  End If

  % >

  <! doctype html >

  < html >

  < head >

  < meta charset = "utf-8" >

  < title > Untitled Document < /title >

  < / head >

  < body >

  < form action = "< % = MM_LoginAction % >" method = "POST" name = "login" > "

  < name of entry = "usercode" type = "text" >

  < name of entry = "password" type = "text" >

  < input type = "submit" name = "Submit" id = "Submit" value = "Submit" >

  < / make >

  < / body >

  < / html >

  Any help would be greatly accepted!

  
  

  'group' is one word reserved in ASE and most other DBMS. You can probably escape, but it is best to never use the reserved words in tables/columns.

• Connect to SQL Server using Windows authentication

  Allows us to connect to the SQLServer database via dblink using authentication SQL Server (Oracle 10 g DB on Windows server) HS, sqlserver db is moved to a new server and there it is configured to use Windows authentication only. Is it possible to use the dblink/HS with Windows authentication on the side of SQLServer? Oracle support answer is no, but I thought I'd ask around...
  
  Thank you!
  
  Published by: user11968137 on March 28, 2013 11:42

  Gateway for ODBC 10 g or 11g is supported only with SQL Server, not Windows authentication authentication.

  If your SQL Server is configured only for authentication on Windows, you have no other way to change the configuration of the SQL Server to support mixed Mode (Windows authentication and SQL Server authentication).

  Kind regards

  Mireille-

• Connection to the SQL Server using Windows authentication

  I would use SQL Developer (v1.5) to connect to an instance of SQL Server 2005 uses windows authentication. I downloaded jtdw - 1.2.jar and set its e path as a preference in the TOOLS\Preferences Database\Third Party JDBC Driver dialog box.
  
  I was able to connect to SQL Server 2005 successfully if I use SQL authentication and provide a user_id and password.
  
  It is my preference to use windows for connection authentication. However, when I try to connect, I get the following error:
  
  Failure - i/o Error: library of native SSPI is not SSO unloaded. Check the system java library path property
  
  I have no idea what it means. I'm not a java programmer and I am very new to Oracle in general if someone can give me some guidance right ahead as to what lack me?
  
  Thank you

  After reading the thread referenced by Jim Smith (thanks!), I wanted to copy the information in this topic... and update to say that these same steps for SQLDeveloper 1.5.1 & SQL Server 2005. Don't miss step 5, if you want to enable NT authentication.

  {Of referenced post}

  SQL Developer for MS SQL SERVER 2000 Setup

  (1) install/extract SQL Developer 1.2.1 in C:\Program Files\Oracle
  Do {$sqldevhome} = C:\Program Files\Oracle\sqldeveloper

  (2) get the Pluggin JDBC SQL SERVER (jtds - 1.2.2 - dist.zip) of:
  http://sourceforge.NET/project/showfiles.php?group_id=33291&package_id=25350

  (3) unpack jtds - 1.2.2 - dist.zip
  Created: jtds - 1.2.2.jar
  \x86\SSO\ntlmauth.dll

  (4) copy the jtds - 1.2.2.jar in:
  {$sqldevhome} \jlib directory.

  (5) copy the dll in the \x86\SSO subdirectory ntlmauth.dll in:
  {$sqldevhome}\jdk\jre\bin\ntlmauth.dll

  (6) with SQL Developer:
  Go to the Menu 'tools '.
  -Preferences...
  Expand the "[+] database
  Choose "third-party JDBC Drivers.
  Click on 'add an entry '.
  Then locate your copy of '{$sqldevhome}\jlib\jtds-1.2.2.jar '.
  Note: Use the name of the jar file, not its parent for the input directory.

  7-restart SQL Developer and try your SQL Server 2000 (or SQL Server 2005) link

• 802.1 x (dot1x) with IP phone / workstation using several authentication domains (MDA)

  Scenario:

  Workstation (behind the phone)

  8.5 (2) software IP Phone 7911

  ACS 4.1 with AD on the same server

  Cisco switch WS-C3750E-24PD with c3750e-universalk9 - mz.122 - 53.SE1.bin

  Guide used:

  http://www.Cisco.com/en/us/Tech/tk389/tk814/technologies_configuration_example09186a00808abf2d.shtml

  http://www.Cisco.com/en/us/products/sw/secursw/ps2086/products_configuration_example09186a00801df0e4.shtml

  To accomplish:

  Computer and authentication of the IP phone with 802. 1 x. The phone using EAP - MD5 and the workstation with PEAP-MSCHAP version 2.

  Tried and worked:

  Workstation using EAP - MD5 (with ACS username) and use PEAP (with AD user name) and it also acceded to the vlan correct according to the username.

  The journal of the ACS, authentication failed:

  Message-Type-name of user - Group-Name-Caller ID - network access profile name - Code failure-authentic -.

  Authentic has no EAP type - CP 7911 G-SEP00254594D6BA--00-25-45-94-D6-BA VOZ - (default) - not configured

  Configuration of the Switch:

  Group AAA dot1x default authentication RADIUS

  Group AAA authorization network default RADIUS

  RADIUS-server host 10.32.250.250 auth-port 1645 acct-port 1646 borders 7 095F4B07110445425B54

  interface GigabitEthernet1/0/3

  switchport mode access

  switchport nonegotiate

  switchport voice vlan 200

  multi-domain of host-mode authentication

  Auto control of the port of authentication

  periodic authentication

  MLS qos trust device cisco-phone

  MLS qos based on vlan

  dot1x EAP both

  dot1x quiet-time 20

  dot1x timeout server-timeout 100

  dot1x tx-delay 100

  broadcast storm control 15.00

  multicast storm-control level 10.00

  spanning tree portfast

  spanning tree guard root

  Summary of ACS Configuration:

  Configured the AAA

  2 group - voice and data, each with their VLAN respective and the ACS configuration parameters (attribute / value (AV))

  Added the user name and password for IP phones

  Mapped the announcement to the DataSet

  A certificate and installed in the workstation

  Set up the configuration of global authentication, where I ticked the boxes PEAP and EAP - MD5

  So, as I said, it only authenticates the workstation w / IP phone.  When I add the IP phone it does not authenticate any of them.

  Someone at - it one day?

  Hello

  First of all, you can try a different sw for phone (for example 8.4.2S). I have a similar problem with the 8.5 software and phones 7945/7965. Secondary, you must attribute av-pair confiigure side ACS for the correct placement of the voice phone to vlan.

  Concerning

  Stanislav

• Machine using certificate authentication

  Hello

  I am facing this error while the machine authenticates agaist AD for wireless users. My requirement is users with company laptop get vlan privileged and BYOD should get vlan normal. I use Cisco ISE 1.1.1 and rules of authentication configured in client diffrenciate based on the assets of corp and BYOD. Result of the authentication policy is sequence of identity that uses the certificate profile and AD. All laptops Corp. must be authenticated using certificates and then followed by past and user of the AD. When I set up XP users to validate the certificate of the server this error comes in Journal of ISE "failed authentication: 11514 suddenly received empty message TLS; treat it as a rejection by the customer' and if I turn off validate sewrver certificate then this error "failed authentication: 22049 binary comparison of the certificates has failed."

  Any help?

  Thanks in advance.

  Hello

  It is a limitation on native begging him, when you activate the smart card or certificate of authentication for the network connection, and then he tries to use it for the computer and user authentication. It does not use certificate for machine auth authentication and authentication of the password for the user authentication.

  You can use the anyconnect Network Access Manager (which is free if you have a cisco wireless network) and not only it allows you to define what type of desired authentication (certificate of machine) and password for the user, but it has a new feature called the chaining of eap. Chaining of EAP is a powerful option because you can choose the order (machine first then user) when the client connects to the network. You have is no longer to point out about machine authentication timers and I was wondering what that is best suited when it comes to registration of users in and out of their machines in order to refresh the cache of authentication machine at ISE. However chaining eap uses eap-fast, which is a framework for authentication based on the CAP.

  This is the last note of release on this feature (currently in beta):

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect31/release/notes/anyconnect31rn.html#wp998871

  Tarik Admani
  * Please note the useful messages *.

• VPN concentrator - using several authentication servers

  Hello

  I have a question regarding the use of more than one authentication server to authenticate users connecting to a VPN concentrator.

  Is it possible to add several, different (for example: SDI and RADUIS) servers for authentication in the list and make sure that users authenticate to each other to establish the VPN. It seems just a user to authenticate through one of them to establish a VPN. Can you make the user to authenticate through multiple servers?

  Thank you

  Cam

  Cam

  I have no experience with this issue, so I have an opinion but no facts. I suppose that it is possible to separate the authentication of the user of the NAC/posture validation.

  Perhaps someone with experience with this or the necessary expertise for this can help us with some facts.

  HTH

  Rick

• local group can be used for authentication to the remote user?

  Hello

  Can I use local user databease created the PIX as authentication method for remote access VPN clients. When tried to make using PDM following error has been shown

  "Local group is not taken care of for the user remote auth.of a client remote easy vpn." Please select another group of servers auth... »

  Snapshot of PIX is attached.

  This cliché is: suite menu.

  ---> VPN configuration---> remote access--> vpn cisco client---> select the Group---> edit--> Advanced-->

  Is there is another way, what can I use the local PIX basic data itself to authenticate users from the outside world of the VPN client.

  no doubt this pix is able to authenticate the user remote vpn against its local database.

  Here are the code examples:

  access-list 101 permit ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0

  access-list 120 allow ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0

  (Inside) NAT 0-list of access 101

  part of pre authentication ISAKMP policy 10

  ISAKMP policy 10 3des encryption

  ISAKMP policy 10 md5 hash

  10 2 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  ISAKMP identity address

  ISAKMP nat-traversal 20

  Crypto ipsec transform-set esp-3des esp-md5-hmac vpnset

  IP local pool ippool 10.1.1.11 - 10.1.1.21

  vpngroup address ippool vpnclient-pool

  vpngroup idle 1800 vpnclient-time

  vpngroup vpnclient-Server dns 139.130.4.4

  vpngroup vpnclient password cisco456

  vpngroup split tunnel 120 vpnclient

  Crypto-map dynamic dynmap 10 transform-set vpnset

  map remote_vpn 20-isakmp ipsec crypto dynamic dynmap

  Cisco username password cisco123

  AAA-server local LOCAL Protocol

  client authentication card crypto remote_vpn LOCAL

  client configuration address card crypto remote_vpn throw

  client configuration address card crypto remote_vpn answer

• VCSC &amp; VCSE: device/user using LDAP authentication

  Hi all

  I configured the VCSC and VCSE for device authentication and the user using LDAP. The issue that I face is my Zone of course does not have connection to VCSE. I am sure that my LDAP works very well because everything works perfectyle (authentication of users, for example) with the exception of this. Status I got STRANDED on the page of the area traversed in VCS C.

  Has anyone encountered the same problem?

  It's not a problem, it's the behaviour, as the crossing area also uses authentication, then

  It will not use the local db but using your ldap server.

  You create an additional account with the user name used on the VCS that reflects the

  SIPIdentityUserName / h235IdentityEndpointID and the password as well.

  Works very well for us.

• How to use the authentication of the URI (e-mail) of MRA - different domain through the highway-C

  Hello

  I am not able to connect to the MRA using my E-mail address. How to solve it?

  My account is [email protected] / * / (this is my domain name locally, not resolved on the internet)

  My email (URI) is [email protected] / * /

  If I connect to internet using my ID of combined directory with my external internetresolvabledomain.com, IE [email protected] / * /, then she succeed.

  But if I use my e-mail address, it cannot be authenticated because the highway to remove the domain, and then ask the CUCM for validation.

  Question: How will I know the Expressway-C that this area is an e-mail address (URI) of my iantra123 account?

  And, said the Expressway-C do not delete this domain for authentication?

  Kind regards

  Antra

  OK, on ARM, when he uses NODES to search for the user in your CUCM, it won't work if you use the IADB, if you use e-mail, it will return a not found message, you can see that the EXP - C opens a session.

• Developer SQL 4.1.2 uses Windows authentication to connect to SQL Server

  I'm using SQL Developer 4.1.2 and tries to connect to SQL Server through Windows authentication.  If I use SQL Server authentication, everything works so the jTDS driver appears to be installed and working properly (I use jTDS 1.2).  When I switch to Windows authentication, I get the error

  Status: Failure-Test failed: IO error: failure of the SSO: library Native SSPI has not loaded. Check the system java.library.path property.

  Of course, I googled the error and came up with dozens of people asking the same question and is told to move the ntlmauth.dll from the \SSO directory to the jTDS directory in various other directories.  That seems to work for others so for the last few hours, I was copying the DLL in each directory that I can find someone on the internet suggesting without success (I do restart SQL Developer each time).  In the Directory SQL Developer, I tried

  Developer c:\Oracle SQL 4.1.2.20.64\sqldeveloper

  Developer c:\Oracle SQL 4.1.2.20.64\sqldeveloper\sqldeveloper\bin

  Developer c:\Oracle SQL 4.1.2.20.64\sqldeveloper\jdk\jre\bin

  
  

  On the off chance that something was still making reference to a directory of a SQL Developer previous install, I put it in the same directories in the front THAT SQL Developer installed on this machine.  On the theory that she was using the FMV of the machine rather than that I downloaded and installed with SQL Developer, I advanced and dropped the DLL in the directory \bin for each installation of Java, that I could find on the system.

  
  

  c:\Program Files\Java\jrd1.8.0_45\bin

  C:\Program Files (x86)\Java\jre1.8.0_45\bin

  C:\Program Files (x86)\Java\jre1.8.0_60\bin

  
  

  Still no luck.  SQL Developer, I went to help. Everything | Properties and checked that the first way to java.library.path is what I expected and where I dropped the ntlmauth.dll first.  I even put it in c:\windows and c:\windows\system32 just to be sure.

  
  

  Java.Library.Path

  C:\Oracle SQL Developer 4.1.2.20.64\sqldeveloper\sqldeveloper\bin. C:\WINDOWS\Sun\Java\bin; C:\Windows\System32; C:\WINDOWS;

  
  

  Despite the DLL just about everywhere that I guess I would need to have it, I still get the same error.  I must be missing something obvious.  But at this point I was looking at it so long that I just can't see it.

  
  

  Justin
  

  
  

  
  

  I use SQL Developer 4.1.2 and tries to connect to SQL Server through Windows authentication using jTDS 1.2

  Not sure if this has anything to do with your problem, but according to jTDS - SQL Server and Sybase JDBC driver / newsand since SQL Developer 4.1.x requires Java 8, '' you should stick only to jTDS 1.2 If you need to use a version of Java before Java 7 '' . Perhaps using a version 1.3.x jTDS driver might help.