Get some VLAN voice to work on 5548P

Similar Questions

• RV180 router: impossible to get Inter-VLAN routing to work.

  I've been hit in this now for two days and just can't get Inter-VLAN routing to work on this router.

  Here is the place is:.

  Updated to the latest firmware of Cisco (1.0.1.9).
  From default settings, I added 2 VLAN as follows:

  VLAN (id = 1) default: dhcpmode = port IP=192.168.1.1/24 from server 1
  VLAN vlan2 (id = 2): dhcpmode = port IP=192.168.2.1/24 from Server 2
  VLAN vlan3 (id = 3): dhcpmode = port IP=192.168.3.1/24 Server 3

  (without link)
  WAN port
  |
  Routing/NAT
  |
  --------------------------------------
  VLAN ip 192.168.1.1 192.168.2.1 192.168.3.1
  name of VLAN by default vlan2, vlan3
  VLAN id ID = 1 ID = 2 ID = 3
  Inter-VLAN only routing Yes Yes
  Excluded excluded unidentified 1 port
  2 excluded excluded Untagged port
  Port 3 unmarked excluded except
  Port 4 (not interest) without excluded tag excluded
  ---------      --------     --------
  1 2 3 Port port
  |              |            |
  AdminPC PC3 PC2
  192.168.2.191 192.168.3.181

  PC2 is assigned an IP address of 192.168.2.191 (DGW = 192.168.2.1) - OK
  PC3 is assigned an IP address of 192.168.3.181 (DGW = 192.168.3.1) - OK

  (IP 192.168.2.191) PC2 can ping 192.168.2.1 and 192.168.3.1 - OK
  (IP 192.168.3.181) PC3 can ping 192.168.3.1 and 192.168.2.1 - OK

  BUT...
  PC2 cannot ping PC3 - don't DO NOT WORK
  PC3 can not ping PC2 - don't DO NOT WORK

  (does not work in gateway and router Mode)

  CAN SOMEONE HELP ME UNDERSTAND WHY?

  Your help is very appreciated.

  I bought this unit specifically because she supported routing inter - VLAN!

  Vlaminck

  ---------------------------------------------------------------------------

  Support information:

  Screenshots:
  Belonging to a VLAN:
  VLAN ID Description Inter VLAN device Port 1 Port 2 Port 3 Port 4
  Routing Mgment
  1 default disabled enabled unmarked excluded excluded unlabeled
  2 active active VLAN2 excluded unmarked excluded excluded
  Unmarked 3 VLAN3 active active excluded excluded excluded

  Several subnets VLAN:
  VLAN ID IP address Subnet Mask DHCP DNS Proxy Mode status
  1 192.168.1.1 255.255.255.0 DHCP Server enabled
  2 192.168.2.1 255.255.255.0 DHCP Server enabled
  3 192.168.3.1 255.255.255.0 DHCP Server enabled

  Routing table (Bridge Mode)

  Destination Gateway Genmask Metric Ref use Interface Type flags
  127.0.0.1 127.0.0.1 255.255.255.255 1 0 0 static lo upward, gateway, host
  192.168.3.0 0.0.0.0 255.255.255.0 0 0 0 dynamic bdg3 to the TOP
  192.168.2.0 0.0.0.0 255.255.255.0 0 0 0 dynamic bdg2 upward
  192.168.1.0 0.0.0.0 255.255.255.0 0 0 0 static bdg1 to the TOP
  192.168.1.0 192.168.1.1 255.255.255.0 1 0 0 static bdg1 upward, gateway
  127.0.0.0 0.0.0.0 255.0.0.0 0 0 0 lo dynamic

  Routing table (router Mode)

  (Ditto)

  Hello

  It's not because the pings are allowed on the same subnet that they come from a different subnet.

  You probably have a firewall problem windows software because that by default, it removes a different subnet icmp echoes.

  Concerning

  Alain

  Remember messages useful rate.

• I'm about to upgrade premium creative design cs4 for I mac 10.11.2. can I still use it? If it's not like I'm retired and I have only some minimum number of works during the year, I can upgrde at a regular bundel and to add a tax when I get to work, and/or

  I'm about to upgrade premium creative design cs4 for I mac 10.11.2. can I still use it? If it is not that I am retired and I have only some minimum number of works during the year, I can upgrde at a regular bundel and to add a tax when I get to work, and/or monthly pay depending on my work schedule?

  Move the discussion to the download, installation, commissioning.

  Please check the terms of System. Adobe Creative Suite 4, Point products. You can upgrade to the App only and add more applications each time as needed. Please check: pricing and membership creative cloud plans | Adobe Creative Cloud for more details on the plans and prices.

  I hope this helps.

• VLAN voice N3048P and DHCP issues

  Hello

  I just received several switches for our N3048P and 2 x 4048 access layer - WE for our base layer. Are the N3048P VLT'd between two of 4048. There are 4 x N3048P of one on the other. The 4048 possess all gateways via VRRP.

  I have 802. 1 x works with my Windows client test, and I can get the phone (Cisco 7941) to acquire a DHCP address if I put it on a port "switchport mode access. However, if I change the port to a general port with vlan enabled voice and 802. 1 x, the phone does not have a DHCP address, but the PC attached to the phone Gets a DHCP address in the VLAN correct.

  I see CDP and LLDP messages exchanged via Wireshark, and it seems that the phone and the switch are to exchange the VLAN voice correctly.

  My question is, why the phone can't one address DHCP?

  Here's the relevant config of switch below. I know that some of the config can be duplicated for troubleshooting steps:

  VLAN 75
  the name 'Test '.
  output
  VLAN 76
  name "Test_Phones".
  output

  IP helper-address 1.1.1.3 dhcp
  IP helper-address 1.1.1.4 dhcp

  interface vlan 75
  IP 172.16.75.4 255.255.255.0
  IP helper 1.1.1.3
  IP helper 1.1.1.4
  output
  interface vlan 76
  IP 172.16.76.4 255.255.255.0
  IP helper 1.1.1.3
  IP helper 1.1.1.4

  AAA authentication local connection to "defaultList".
  radius of start-stop AAA accounting dot1x default
  control-dot1x system-auth
  radius AAA dot1x default authentication service
  AAA authorization network default RADIUS

  VLAN, VoIP

  source-ip 172.16.75.4 RADIUS server
  Server RADIUS 'key' key
  RADIUS-server host 1.1.1.1 auth
  primary
  name "rad1.
  use of 802. 1 x
  key 'key '.
  output
  RADIUS-server host 1.1.1.2 auth
  name "rad2.
  use of 802. 1 x
  key 'key '.
  output
  Server RADIUS acct 1.1.1.1 host
  name "rad1.
  output
  host server RADIUS acct 1.1.1.2
  name "rad2.
  output

  Gi2/0/1 interface

  Description '802. 1 x client port.
  spanning tree portfast
  spanning tree guard root
  switchport mode general
  switchport general allowed vlan add 75-76 the tag
  dot1x re-authentication
  dot1x quiet-period 5
  dot1x tx-period 5
  dot1x comments - vlan 20
  dot1x Informati-vlan 20
  LLDP transmit tlv ESCR-sys sys - cap
  LLDP transmit-mgmt
  notification of LLDP
  LLDP-med confignotification
  VLAN voice 76
  disable voice vlan auth
  output

  Thanks for any input you may have. I would like to know if there is any other information, I can provide.

  -Jason

  That ends up being the correct port configuration:

  Gi2/0/1 interface

  Description '802. 1 x client port.

  spanning tree portfast

  switchport mode general

  switchport General pvid 75

  VLAN allowed switchport General add 75

  switchport general allowed vlan add 76 tag

  dot1x port-control on mac

  dot1x re-authentication

  dot1x quiet-period 5

  dot1x timeout supp-timeout 15

  dot1x tx-period 5

  dot1x comments-vlan-deadline 15

  dot1x comments - vlan 20

  dot1x Informati-vlan 20

  VLAN voice 76

  disable voice vlan auth

  The most important line here is «the dot1x port-control on mac» I got 'auto control by port dot1x' configured, but it does not work as expected. In addition, defining the comments-vlan-period and supp-timeout were necessary. If the port was shot, the switch would not necessarily reauth port.

• N2048 level 3 - routing only some VLAN?

  Imagine this scenario - simplified our desired mounting

  VLAN 1 - Server vlan 192.168.1.0/24

  VLAN 2 - customer VLANs 192.168.2.0/24

  VLAN 50 - guest wifi vlan 192.168.50.0/24

  We want to move freely between VLANS and VLAN 1 2 but prevents all movement of traffic at VLAN50

  I have read and understand this guide routing VLAN from Dell , but this covers only the scenario when you are happy for everything to flow between all the VLANS.

  I have a few questions that it would be great to have some help with

  (1) global routing - we believe that if we

  IP routing

  This will bring all the VLAN is not what we want - correct?

  (2) However, if there is no IP address defined on the interface VLAN 50, it won't drive, correct? So as not long that no VLAN we want to isolate has an IP address assigned to that VLAN, no routing?

  Thus, we could then issue a command "ip Routing", and we would get what we want, provided never configure us an IP address on the interface VLAN 50. What we'll call "Solution A" - how?

  (3) static routing - if we emit static routes to specific subnets this will allow all the VLANS whose defined on the interface IP address to route their

  for example if I do

  IP route 192.168.1.0 255.255.255.0 192.168.1.1

  then VLAN 2 VLAN 1, but can can 50 VLAN

  Is this fair?

  (4) However, if, I ever create a route to VLAN 50, then although traffic could channel VLAN 50 to VLAN 1, answers could never return once again - right?

  We will call this B - walk-it solution?

  (5) if we wanted to make static routes that only apply in some VLAN it looks as if DNOS has a setting of vlan for the command from road ip - but I can find no explanation of exactly what it means or how it works?

  We will call this solution C - would this work?

  (6) Finally, assuming that all of these solutions work, which is the best solution?

  Thank you.

  The # ip routing command, performs the overall active routing. For routing to occur the VLAN must have an IP address. You are right, if the VLAN is L2 only and does not have an IP assigned to it, deals with this VLAN will not able to reach the other VLANs.

  Static routes will be used to direct traffic to the next network hop. This is usually used to indicate traffic in your firewall. Static routes would not be to direct traffic to a VIRTUAL LAN to another VIRTUAL LAN on the same switch.

  What camera do you use as your firewall? It is not uncommon to set up a similar scenario to your solution A. leave the road to switch between server and client VLAN. Then leave comments VLAN in L2 and the trunk of the VLAN to the firewall. Then let the firewall manage access to resources on the network and internet guests.

  Another option would be to enable routing between all the VLANS, but then apply an ACL to restrict access on the guest VLAN. Page 629 of the user's guide begins detailing ACL, how they work and how they are configured.

  http://Dell.to/1WFiTWT

• Configure the VLAN voice and data in CISCO SF 300 8 P

  I have a couple of Cisco SF 300 8 P and P 24 switches. I have voice and data VLANS configured as:

  Data VLAN: default 145.17.59.0/24

  Voice VLANS: VLAN 20 172.22.20.0/24

  I have different DHCP servers regarding the data VLAN, we have a physical server that is configured for 145.17.59 * extended IP and Voice VLAN DHCP Server is configured as a router gateway with option 150.

  This configuration works very well with other cisco 2960 switches and 3750 etc. except CISCO SF 300 8 P and 24 p. I tried to set up the voice and data VLAN in these CISCO switches so that phone CISCO (model 6941) should get IP of the VLAN voice and PC should get the IP address of the DHCP server on the data VLAN. I tried several techniques such as LLDP, Port-to-VLAN Config etc.

  Can anyone please guide me / help on this.

  Kind regards
  A K.M.Sayeed

  Hi A.K.M., with Cisco phones you should be able to define simply automatic voice VLAN to be VLAN20.

  ID of the vlan 20 voices

  You must ensure CDP or LLDP is enabled as well. I would check in the web GUI. DHCP for phones can come from a DHCP server on a port access VLAN20 switch, or you can use dhcp for assistance to redirect DHCP server elsewhere.

  If you prefer or you have problems with the CDP or LLDP, you can also program the ports as trunks and add the tag VLAN 20 for them.  In this scenario, you need to ensure inter - vlan routing works and phones that download the file config with corrrect VLAN config.

  These switches do not run ios, so they are similar, but different from the catalyst switches that you mentioned.

  -remember messages useful rate.

• How can I get a dynamic mic to work on the iMac?

  How can I get a dynamic microphone to work via the usb input? Do I need a plug-in?

  Well Yes, if it is a USB microphone, the support is to plug.  Note, Apple provides an Audio configuration and Apple Midi utility in Applications-> utilities that once connected develops on the parameters in the menu-> Preferences-> sound-> entry

  Some microphones require Mac OS X drivers.  It would therefore be important to determine if yours is a.   Google your brand and model micro with Mac OS X and the drivers of Word to see if someone needs.

• Qosmio X 770 - 11 c - some things do not work after reinstalling Win 7

  I just had windows reinstalled to correct some problems with the connection to a MAC mini server.
  But some things do not work as before:

  The USB 3.0 port does not work.

  FN key does not work (if you press FN and Z I used to get a toolbar at the top and then be able to change the lighting of the keypad)

  Toshiba Eco isn't here

  ETC., essentially all the toshiba Add ons/programs delivered pre-installed.
  I need to intall all drivers and is at - it somewhere I can get them all in?

  Thank you very much

  All Toshiba drivers can be downloaded from the Toshiba UE driver page:
  http://www.Toshiba.EU/innovation/download_drivers_bios.jsp?

  You will find common Toshiba drivers and all the special tools and utility that must be installed to get all the extra features portable works correctly.

• Some software will not work on Windows Vista

  Some software will not work on Windows Vista so I need to install Windows XP
  But how to download drivers for devices such as bluetooth, Lan, his...

  Hello

  I put t know what phone you use, but many Toshiba notebook series are delivered and support similar hardware parts.
  You can simply try to test and install the drivers from different series.

  The new Toshiba Bluetooth stack supports Vista and you can install it on all the laptops Toshiba which supports the feature of BT.
  Sometimes, you will get the chip card driver LAN or compatible Sound on the site of manufacture of chips like Intel, realtek, etc.

• Impossible to get PRTSCR DEL + keys to work on the Satellite A100

  I have the Satellite A100 - 232 PSAA2E. Bought in Greece... If some of the keys have a second role - for Greek letters. Especially not a problem.

  However... I can't get led (top-right) to work and same (3buttons on the left led) the print. Is there a setting to change or is there another way to remove and print screen?

  Your ad is somewhat confusing. Satellite A100 is pretty old laptop so I do not understand how you have this problem now.

  Everything was ok in the past?

  As far as I know you can change the keyboard input language, but this has nothing to do with DEL or PRINT key features.

• Re: Unable to get the wireless adapter to work on my Satellite L550-1CC

  I'm getting bored with this laptop, I reinstalled windows 7 (32 bit) and can not get the wireless adapter to work.

  My router settings are perfect, my netbook is zero connection problems - the router is just inches away from the laptop most of the time - the laptop insists that there is "no available networks."

  This of course is BS, before I reinstalled windows I could pick up 3 other neighbouring networks as well as mine.

  Windows automatically installed the wireless network - I thought that could be the problem, so I downloaded the realtek driver directly.

  No difference. Always the small icon with Red Cross barred through it.

  I thought it could have been a hot key problem - so I installed the flash card driver that apparently controls the access keys (for some reason any).

  Shortcut keys still don't work - I could really care about that - it's just the wireless network I need.

  Thanks for any help I receive.

  > my netbook has zero connection problems - the router is just inches away from the laptop most of the time - yet the laptop insists there is "no available networks."
  After reading this sentence, I'm a bit confused. If there is no available WLAN networks how your laptop had zero problems to connect?

  One last thing:
  > Of course is BS, before I reinstalled windows I could pick up 3 other neighbouring networks as well as mine.
  What is the difference between the old and the new installation of Windows?

  In general the WLAN use is fairly simple.
  Wireless network card - must be installed correctly (listed in Device Manager
  WLAN card - must be enabled using FN + F8 key combination to activate the wireless network card
  -scan the available WLAN networks area, click on the button of your WLAN and use connect
  -put key WLAN if necessary and after a few seconds WLAN connection will work

  I did this many times on laptops preinstalled Win7 and didn't have any problems. On all laptop computers pre-installed with Toshiba recovery image (factory settings) is not necessary to change the WLAN settings.

• Using Logitech attack 3 joystick, some button do not work or work properly. Do need to be configured.

  Installed Flight Sim X - also downloaded the drivers for the controller Logitec. Components and fittings are directional. for example, I can extend components but does not retract them. I can cut the nose upwards but not downwards. Does anyone have short suggestions to get a different joystick. FSINSIDER lists it is a recommended.

  Hi jmcaruso53,

  
   Welcome to Microsoft Answers Forums.

  We would like to get some more information from you to help solve your problem.  You better, please answer the following questions.

  When was the last time it was working fine?

  You have installed the drivers available for joystick from Logitech Web site?

  You will have to perhaps install the drivers for the broom handle, see the link below to download the drivers from the Web from Logitech website and make sure that you select the correct version of windows before you download the drivers.

  http://www.Logitech.com/index.cfm/441/302&CL=us, en & hub = 1? selectedcrid = 441 & selectedcid = 302

  Suggest you to check if the controller is configured in the "game controllers".

  Open game controllers by clicking the Start button, click Control Panel, click hardware, click on game controllers, and then check if the joystick is configured to be used as a gaming device. http://windowshelp.Microsoft.com/Windows/en-us/help/6065f372-90DD-44cd-BC8D-c89d17f0fdfd1033.mspx

  You may need to check the settings les parametres joystick, please see the link below.

  http://www.fsinsider.com/product/learning/pages/default.aspx

  Hope this information is useful.

  Let me know if it worked.

  All the best!

  Thank you, and in what concerns:

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• After having recently updated windows, some programs no longer work. In addition, System Restore does not work.

  After having recently updated windows, some programs no longer work.  Also, when I went to do a system restore, that he would not allow me to restore to an earlier date.  Among the programs that no longer work are VLC Media player, ieploxer, f.lux.  Even though I have uninstalled and reinstalled they would not load correctly.  I would get the splash screen for the program, but noting else.  When I am gone in Windows Task Manager the program would not appear in Applications, but there are processes running.  And an interesting thing, the exe afficheraient use of the 72K memory.  Still, even for different programs.

  What can I do?

  Start the command prompt, and then type

  sfc/scannow

  Do check and see what the result is.

  Also run full system scan with:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

• I can't get EMET 2.1 to work on XP Home machines

  I can't get EMET 2.1 to work on 2 computers XP Home.

  I understand that I will not be able to configure the system wide DEP on XP Home versions, but I should be able to participate of the individual claims of DEP using the button "Configure Apps".  Problem is that does not either, on two different machines... I added the browser, pdf, customer e-mail reader and Media Player, but when I restarted these applications, they did not appear in the lower pane as running EMET.

  It is my understanding applications, when adding, supposed to be indicated as a checkmark green or any other symbol next to them?

  I see neither EMET in Process Explorer.  :(

  Of course, I could use some assistance.

  Hello

  I suggest you to report this problem in the TechNet community.
  http://social.technet.Microsoft.com/forums/en/Emet/threads

• After the removal of malicious software through the system restore, now some applications don't work

  Control Panel... Help and Support... do not work... I get this message on both of these and other:
  Rundll32.exe not found Application...
  When I try to access some also uses Open with open... This has not happened before... I think I lost something that needs to be restored... BTW I tried the system restore to get rid of malware... It worked (obvriously) but only up to a point... Now, some applications do not work...
   
  Thank you
   
  Elaine

  Then when you get your rundll32.exe work, follow these steps:

  Looks like your Windows file associations have to dispose. This means that XP is not
  know what to do with the files by looking at the file extension (for example, .exe for executables,
  .doc for MS documents, etc.).

  If you don't have it you, something done for you - most likely malware.

  Go to this site WWW by Doug Knox:

  http://www.dougknox.com/

  On the left, click on the Win XP fixes, file Association fixed and read the instructions at the top of the page.

  Download the EXE File Association Fix on your desktop, unzip the file and apply it by following the instructions at the top of the page, then to restart and test.

  Run the following scans for malware, and then fix any problems:

  Download, install, update and do a full scan with these free malware detection programs:

  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  They can be uninstalled later if you wish.