graphics problems "thin client".

Similar Questions

• Thin client HP 420: thin client usb problem

  We test a workstation 420 and everything seems to work fine except when you are connected to an RDP session to our server 2012R2 farm, usb storage disks/keys are not recognized.

  Everything seems to be ok on the thin client in local resources and the USB is recognized when a usb diagnosed.

  Other usb devices are thin dongles, wireless, keyboard / mouse, etc.

  Any thoughts on how to get them recognized in windows Explorer

  So nobody here knows something about thin client HP configurations

  Spoiler (Highlight to read)

• Thin Client connection problem

  Hi Folks,
  
  I have a issue to solve with some new thin client (Devon IT TC2B)and I really need some help 
  
  When I use the view client from any PC or from my Mac, everything works perfect!
  
  But I a use my new Thin Client with the View Client embedded I have the following error:
  
  "The secure connection to the View Server has unexpectedly disconnected.
  
  

  Any ideas? If anyone can help me I'd really appreciate it!

  Thanks in advance!

  Randy C.

  PS: I have attached a screenshoot from my mistake of thin client.

  I see 2 possibilities:
  -A network issue affecting the Thin Clients.  Settings DNS, Firewall, etc.
  -The Client of the view needs to be refreshed on Thin Clients.

  Best regards

  Patricio Cerda

• Thin Client T520: Hp Thin Client Test without account 'user '.

  Hello

  My problem is that I created a new account user without administrative privileges for a long time and yesterday, I deleted the user account original (I still have the administrator and the new), but the customer never resumed. I can see the mouse, but it does not start.

  I have the Lightweight Client T520 with Windows 8.

  According to the message that you have posted, I wish to confirm that the operating system could be damaged and need to re - install the operating system on the workstation again to make it work

  This Thin Client device comes with various types of operating system by default, as shown below:

  

  Here is the link to this page: http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=6875922 & lang = to & cc = us

  I don't see Windows 8 (32 bit) operating system on the HP Support Site's list

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the white button on the right to say thank you Thumbs Up *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

• 4.7 HP Device Manager: HPDM finding Thin Clients

  I'm trying to implement HP Device Manager 4.7 on a newly configured Windows 2012 R2 server.

  I am replacing a Server 2008 R2, where HP Device Manager works perfectly on our network.  In fact, if I uninstall HPDM on the new server and reinstall it on Server 2008 R2 I can always access all thin clients.

  The only difference I see in the facilities which is for some reason any gateway in HPDM is not a subnet mask.  Research of the device are not lacking, they don't sell anything or simply continue indefinitely until I have Cancel.

  Any help would be great.  Thanks in advance.

  Just to confirm: you did turn with HPDM 4.7 on Server 2008 R2 successfully, but not the right to 2012 R2 server?

  Is your Windows 2012 R2 server with more than 1 NIC card? Could you please assign a specific NIC loca in the Gateway Configuration window and see if that fixes the problem?

  Otherwise the logging level value please DEBUG and post the gateway.log when start HPDM Gateway

• Shado task does not connect to the Thin Client

  Trying to hide a T520 on HPDM 4.6SP4 thin client, when I run the task of shadow, I retrieve a VNC connection on the server HPDM and not the thin client. T520 thin clients are ThinPro 5. This happens on the T510 Smart thin clients zero Core as well. I'm guessing there's a conf file that may have a value defined by mistake, but didn't find it.

  Dear customer,

  Welcome and thanks for posting your query on the Forum from the HP Support

  Looks like you are facing difficulties regarding the task of the shadow copy in the HP Device Manager

  1 shadow task uses the built in VNC server for the HP Device Manager software

  2. If you have installed a separate VNC software on the server of HPDM, there could be a conflict

  3. also please check under "services.msc" to find out how many services VNC running concurrently

  4. If you find that several services VNC please disable those who is not necessary

  5. Please goto Add / Remove programs and uninstall VNC Viewer is installed separately

  Hope this helps, for other queries in response to the post and feel free to join us again
   
  * Click on the button white Thumbs Up on the right of say thank you *.
  Make it easier for others to find solutions by checking a response "accept as Solution" if it solves your problem.
   
  Thank you
  K N R K
  Although I am an employee of HP, I speak for myself and not for HP

• HP Thin Client T5550: HPDM - sending of the zone settings

  Hello everyone, I have a huge issue with my HP Device Manager and I would appreciate your help.

  When I try to send to my HP Thin Client T5550 time zone settings, it is just the time zone of Dublin.

  It doesn't matter what time zone I send, it always comes back to the zone of Dublin.

  The only difference between the time zones on my HPDM and my thin client is UTC and GMT.

  On HPDM zone is defined as UTC, but on the thin client, it is GMT. I don't know if this could cause problems? And if so, how can I solve this?

  For your information, when I send the same zone to my HP Thin Client T520 settings everything works smoothly.

  I would be grateful for all the help I can get.

  I guess that we are talking about Windows CE on T5550. It is actually a known issue of HPDM, because Windows CE is thus more complete support of HPDM, this issue will not be fixed in a newer version of HPDM.

  I suggest that contact technical consultant for the extraordinary. Or if you know the order of change of time zone, you can try to change it through files & records task.

• Thin Client HP T510 printer questions

  So we have thin clients. We have a local default printer installed for the administrator who "invades" on the "Default user" profile (which is great, that's what must happen) when we try to install a network printer:

  1. We disable the write filter
  2. We disable the security for the user
  3. We install the printer network under the user's profile
  4. We invited domain administrator credentials.
  5. We enter the identification information and properly install/test the printer
  6. We restart and allow the connection of the user (automatic)
  7. The printer is there, but it says "access denied, unable to connect."

  Key information:

  1. These thin clients MUST have locally installed printers
  2. These thin clients are not on the field, they are the default WORKGROUP

  This seems like it should be easy to make it work, but I can't seem to find a solution and I have worked on it for over a week now. Thanks in advance.

  Solution:

  Put printer driver software on USB stick and install locally via the setup.exe.  Do not use the software in windows, for some reson he has a problem with striking pilots from the network.  Running the driver software installation file locally worked like a champ.

• Thin Client T510: Do not support the SMB for no image preload on Linux platform

  Hello world

  I have a problem with a Thin Client T510 (C4G87AT #ABA), this one came with Windows CE and today I flashed with a USB to thin Pro 5 (T6X52011). When I want to deploy the image I captured (wallpaper, RD Session etc...) I have the following error:

  2015-08-19 15:30:43 [error details]:... /... / Task/linux/ImageTask_Thinpro.cpp@384: Metheod of the Image is not compatible.
  .. /.. / Task/linux/ImageTask_Thinpro.cpp@1624: do not support SMB for no image preload on Linux platform.

  When I look in the console HPDM, I see the T510 and connected

  Agent version: 4.6.3670.21244

  HDPM 4.6 SP5

  OS: T6X52011

  My OS: Windows 8.1 x 64

  Can someone help me please? Thks and have a nice day.

  Hi, thks for this Council. Theres is how I fix.

  Firstly, the master repository has change from D:\HPDM\HDPM to D:\HPDM on the server, so the configuration was not good at the moment. Another thing, the password of the user hpdm has changed in Active Directory, but not in the configuration. I changed all the settings for in line with the current configuration and capture Images of thinpro news works very well and deploy this new works pictures well too but Deplopyement of old images does not work.

  I'll open another thread if I need assistance. In this case, I'll mark as fixed.

• Thin Client CA 10

  No doubt this ad in evil, spot, but could not find the right place to post this.  Admin please move this article to the right place.  I volunteer with a non-profit and is currently trying to help with some tasks that they work.  I had some experience with TC.  I thought we could get a lab of the computer market quickly at the lowest cost.  So I found of these CA10 on ebay.  BL-01-CB, they are ok, I can get into the bios, but it seems that the owner has set the password in the software.  I can't change the settings.  How can I do to solve this.  Is there anyway to reset it to factory settings?  If I flash where can I find procedures and for the flash image with.  Your help will be appreciated.  Thank you.

  Hello ttiger211996,

  When you disconnect a computer some of the capacitors may still have a charge that can make things difficult.

  Unplug the computer and leave it on for a while for logistics I hope that all of the capacitors. Once he has to rest for a little out the CMOS battery for at least 5 minutes.

  Reconnect everything and see if the password still exists.

  A user in this forum thread ran into a similar problem of semi

  Thin Client T5000 series password reset

• Get the Thin Client IP address

  Hello. I'm trying to find out the IP address of the machine that I use for programming. I want to use my LabVIEW program on a server. However, the string to the property intellectual VI gives the IP address of the network, so in this case the server IP address. It is a problem, as we hope, in the future, run multiple thin on program clients, if we want the program to know what thin client, it works on. However, I don't have access to the command prompt on the thin client due to administrative restrictions. This eliminates the other solution I found, which was to find the Login Windows user name (each light client has its own unique user name) through different screw which involved the command prompt. Any ideas on how to find the IP address of the customer of the Services Terminal Server Session, I believe that my computer called? Thanks for your time.

  I called and he was referred to this, which worked. We use Citrix server and the username thing worked, and we are now able to run the program for each thin client using his user name.

• Windows xp works on VESA PC Thin Client eBox-2300

  I need to know if its possible will work windows xp on VESA PC Thin Client eBox-2300
  Here are the specs
  processor == Vortex86 SoC (System on Chip)
  main memory is 128 MB of SDRAM
  It uses a card compact flash for a hard drive thinking about upgrading to 2 giga
  Windows xp runs by chance on it?
  Thank you

  Hello

  It does not support the full version of Windows XP. According to the manual, you can install Windows XP embedded, but you will need to contact the manufacturer for assistance on this.

  For help I recommend that you report this problem in Windows Embedded Standard.
  http://social.msdn.Microsoft.com/forums/en-us/category/EmbeddedWindows

• Thin client HP t610 thin WW: thin client

  Installed an update a few months ago, and everytime I turn on the thin client, he begins to initialize.  After that initial "starting Windows" screen it starts at the end of the update of Windows saying:

  'Stage 3 of 3 '.

  "Configure Windows update."

  '32% complete '.

  "Do not turn off your computer.

  If stays there for a few minutes, then it starts to close.  But it restarts the computer and is stuck in this loop, until I have turn off the workstation.

  NSMerrick, welcome to the forum.

  I think that you will get more responses to your question if you start a thread here.  They are the members who know the better your Thin Client.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• This computer can't connect to the remote computer. ONLY 2 people it out 200 users...? baffeled by WindowsXPe Thin Client RDP connection

  Here's the situation.  We have 2 TS servers running WIN2K3 and 200 users with Thin Clients.  We'll call it the first server A and b of a second.

  They normally connect to an IP address and they will be directed to the server A or B according to the load.

  However; users can still select the specific TS server, they want to connect to.

  If user 1 and user 2 cannot connect to Server B.  They get the error listed above in the title.  However the user 1 and 2 can connect to A server.  If they say:

  192.168.123.2 the two of them get

  192.168.123.3 the two of them cannot get.

  I deleted the user de.3 A profile and it still can't get.  I have checked no orphan key inHKEY_LOCAL_MACHINEMicrosoft\Windows NT\CurrentVersion\ProfileList

  I checked the settings in TSCC. MSC, I' checked worm Licensing by user and they are good, I gave them full administrator privileges and still not pass via the serveur.3, they adhere to all groups within the ORGANIZATIONAL unit that they can connect to TS, they were able to connect to her very well this back on Wednesday.  It is not a firewall issue and port 3389 has been verified in the case otherwise he would not just these two on each CT they try.

  Again, they can get utilisant.2.

  In the event de.3 Viewer I can see users connected CORRECTLY but then it pop their right.  There is no other error message when connecting, just the success Message in the security log.

  Let's bounce servers tonight so I'll have to turn it back on and I pray that they can later log on this server, but I'm baffeled.  Why only 2 people would receive this question and most (not sure how many others there may be, but I know 30 people connected today on this server and worked out of it) people are not getting an error.

  The thin client on their desktop is not the issue, because the error follows them any CLIENT LÉGER, they are connecting from.

  Short of this re-boot and short to delete accounts and recreate them, ideas?

  Found the problem.  I did not remove the key to all the indicated previously.  I should have done that for this user since her CentralProfile Key was empty when she had to be filled in by the system.  Removed his Key specific SID for listed above point and viola.  User can connect.

• Thin client based on Linux T610

  Bulletin Board Hello!

  Just a few questions here I can't find via Google, manual and read other messages of the forum...

  We are trying to use a t610 with the Linux-based operating system and are facing obstacles, a little...

  I saw on the thin clients based on "Windows", after making a change to something, you have to 'Commit' changes...

  Is it possible to do it on a Linux machine? It seems that the operating system partition is read-only?

  Also, is it possible to navigate through the files and folders of this type of thin client?

  I see the terminal in "Administrator" mode and I can't type-nav files and folders through the text editor, but I am a semi-perte to do things this way...

  I know it of maybe a stupid question, but is there a way to recreate the image on this thin client to an OS based on "Windows"?

  The main problem I encounter is an add-on/extension in firefox is not 'stick' in my firefox browser...

  I installed the extension again and after I restart the browser, he is gone and my settings are back to "original"...

  I take a guess here, but I guess whenever this customer "reboots" the start of an image?

  One last question, is there of the "manuals" for those customers based on Linux?

  I see most or all aid seems to aim at Windows and would like to just a reference...

  Thanks for reading!

  Brandon

  If you're talking about the HP ThinPro OS-

  Before you can make changes to the file system, you must run this command from the terminal - "fsunlock". When you are finished, 'fslock' locks the system files again. There isn't another tool file explore included I know in ThinPro. Command line and the Notepad tool are the only real ways to navigate through the file system. If you need help with something, don't forget, it's basically a lighter version of Ubuntu, with a few extra utilities and GUI provided by HP. The nuts and bolts are identical to a version of Ubuntu, so I took a bit of insight of Ubuntu forums online for the problems I've had.

  Regarding your problem of browser extensions, depending on how you do this, you can configure connections to allow them to configure their own settings, or use HP ThinPro settings. If you've not allowed Firefox to create and use its own settings in the file system, nothing don't you change inside the browser will stick. I have not tried to install a browser extension, but I'm sure that this is your problem.