Group ACS 4.2 mapping user

Similar Questions

• Cisco ACS 4.2 a user in several local groups

  Currently, I like this group map

  ACS groups window

  GRP of GRP-A-B-1 and PDM - 2
  GRP - A. GRP - 1

  GRP - Grp-2 B

  For example currently a user test1 is part of two groups 1 and 2 under windows and is mapped to the Grp-A-B of the CSA. Is it possible if I delete the mapping of Grp-A-B in ACS and can see the user test1 speratley in both groups (Grp - A and Grp - B) to GBA?

  Salam Muhammad,

  If you have a local user in ACS, this user cannot be a member of both groups at the same time.

  The same concept applies to external users. They cannot be mapped to two different groups at the same time.

  If you delete the configuration of Grp-A-B, the test1 user will be mapped to the first group in the list because ACS 4.2 process mapping group in the order:

  ' the snip "'

  Order of group mapping

  ACS always maps users to a single group of TISA. However, a user can belong to several groups the group mapping. For example, a user named John could be a member of the ensemble of the engineering group and California, and at the same time be a member of the combination of Group Engineering and management. If the value of group ACS mappings exist for these two combinations, ACS must determine what group John should be affected.

  ACS prevents contradictory group set mappings by assigning an order of mapping for the whole group maps. When a user who is authenticated by an external user database is assigned to a group of ACS, ACS begins at the top of the list of groups for this database mappings. ACS sequentially checks group memberships of user in the database of the external user against each group mapping in the list. Where to find the first set group mapping corresponding memberships to external users in the user database, ACS assigns the user to the group this group map ACS and ends the process of mapping.

  ' the snip "'

  Reference:http://goo.gl/cvc474

  HTH

  Amjad

  Rating of useful answers is more useful to say "thank you".

• Unable to group message when an android user is involved

  Also recently there is 6-9 months, I could text of the group with a particular set of contacts, and then all of a sudden my attempts to send texts of this same set of contacts group failed with "unable to deliver.  I stopped receiving their texts of the group.  I tried texting each contact individually and managed.  I tested other contacts and texts of the group, and those who have succeeded as well.  Finally, I have narrowed the problem down to a particular contact that uses an Android device - when this contact is involved in a group text so I can't send or receive messages from this group text.  Other iPhone users are able to text with this contact group - the problem seems to be related to my iPhone.

  Contact Android has never owned an iPhone, so it is not bound in the middle of old iPhone sound that is left behind on Apple iTunes config.

  I tried to remove and re-add that particular contact, remove all my messages, hard, reboot, upgrade to the latest iOS, etc.. Nothing works.  Any suggestion would be appreciated.

  Hi trask77,

  Thank you for using communities Support from Apple!

  It seems that you are having problems with the group with an Android user messaging.  You can find the following articles useful: send a message from your iPhone, iPad or iPod touch - Apple Support Group

  If you cannot send or receive messages on your iPhone, iPad or iPod touch - Apple Support

  In addition, if you have the person using the remove device Android conversation and then start a new group message to see if it allows messages to go through.

  See you soon!

• ACS 5.2 - authentication user 802. 1 x and MSCHAPv2 using LDAP Source identity

  Hello community,

  I use the ACS 5.2 as the solution of authentication in my network. I configured two situations: access with network access policies and peripheral Administration.

  Currently, I have a few configured devices: 1 ASA (using RADIUS), WLC-5508 (using RADIUS) 1, 1 2960 S (with GANYMEDE +). And I set up an external identity store, using LDAP (I can see and select all groups without problem).

  Everything works fine. My next step was to configure users to use 802. 1 x to authenticate using ACS with my LDAP database.

  Assuming that all configurations are correct on all computers (when I use an internal database works very well), these are the following newspapers/configurations in the ACS:

  

  

  

  

  At this point, we can see the error:

  22043 current identity store does not support the authentication method; He jumps.

  Header 1

  Request for access received RADIUS 11001 11017 RADIUS creates a new session Assess Service selection strategy 15004 Matched rule Access Service - access Police selected 15012 11507 extract EAP-response/identity 12500 prepared EAP-request with EAP - TLS with challenge 11006 returned Challenge RADIUS access Request for access received RADIUS 11001 11018 RADIUS re - use an existing session 12301 extract EAP-response/NAK asking instead to use PEAP 12300 prepared EAP-request with PEAP with challenge 11006 returned Challenge RADIUS access Request for access received RADIUS 11001 11018 RADIUS re - use an existing session 12302 extracted EAP-response containing PEAP challenge-response and accepting as negotiated PEAP 12318 has successfully PEAP version 0 12800 first extract TLS record; TLS handshake has begun. 12805 extracted TLS ClientHello message. 12806 prepared TLS ServerHello message. 12807 prepared the TLS certificate message. 12810 prepared TLS ServerDone message. prepared 12305 EAP-request another challenge PEAP 11006 returned Challenge RADIUS access Request for access received RADIUS 11001 11018 RADIUS re - use an existing session 12304 extract EAP-response containing PEAP stimulus / response 12318 has successfully PEAP version 0 12812 extracted TLS ClientKeyExchange message. 12804 message retrieved over TLS. 12801 prepared TLS ChangeCipherSpec message. 12802 prepared TLS completed message. 12816 TLS handshake succeeded.

  12310 full handshake PEAP completed successfully
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response

  12313 PEAP inner method started

  11521 prepared EAP-request/identity for inner EAP method
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  11522 extract EAP-Response/Identity for EAP method internal
  11806 prepared EAP-internal method call offering EAP-MSCHAP VERSION challenge
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response
  11808 extracted EAP-response containing EAP - MSCHAP VERSION challenge response to the internal method and accepting of EAP - MSCHAP VERSION such as negotiated

  Evaluate the politics of identity

  15006 set default mapping rule

  15013 selected identity store-

  22043 current identity store does not support the authentication method; He jumps.
  22056 object was not found in the identity of the point of sale.
  22058 advanced option that is configured for a unknown user is used.
  22061 the option 'Refuse' Advanced is set in the case of a request for authentication has failed.
  11815 inner EAP-MSCHAP VERSION authentication failed
  11520 prepared EAP-failure of the inner EAP method
  22028 authentication failed and advanced options are ignored.
  prepared 12305 EAP-request another challenge PEAP
  11006 returned Challenge RADIUS access
  Request for access received RADIUS 11001
  11018 RADIUS re - use an existing session
  12304 extract EAP-response containing PEAP stimulus / response

  Authentication PEAP 12307 failure

  11504 prepared EAP-failure

  11003 returned RADIUS Access-Reject

  So, what can be the cause? Compatibility with LDAP?

  Plinio,

  Watch this doc,

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/eap_pap_phase.html#wp1014889

  There is a table which indicates that LDAP is not a database compatible with our EAP type (MSCHAP VERSION-2).

  LDAP, you can use with TLS, PEAP-GTC, and EAP-FAST-GTC.

  TLS uses certificates on both sides, suplicant, and server authentication server.

  * GCT if I'm not mistaken is a WBS system to use with the EAP protocol.

  Authentication Protocol EAP compatibility of database user and table B-5

  Identity store	EAP - MD5	EAP-TLS 1	PEAP-EAP-MSCHAPv2	EAP-FAST MSCHAPv2	PEAP-GTC	EAP-FAST-GTC
  ACS	Yes	Yes2	Yes	Yes	Yes	Yes
  Windows AD	NO.	Yes	Yes	Yes	Yes	Yes
  LDAP	NO.	Yes	NO.	NO.	Yes	Yes
  RSA identity store	NO.	NO.	NO.	NO.	Yes	Yes

  Identity of DEPARTMENT store

  NO.

  NO.

  NO.

  NO.

  Yes

  Yes

• Group Lock VPN 3000 binding users to their group

  I only use a 3015 VPN with VPN Client 3.5.1 using IPSEC. Cisco ACS 3.0 is the radius, all users of the authentication server. If I use a group on the client, I can log in using a different username to groups.

  It is interesting then you get the other privileges of groups for this user as you would expect.

  If I select group Lock on core group settings is not any effect.

  I want to restrict the access of clients to the users group in its own configured.

  I use an external authentication to the Radius ACS server for groups.

  Thanks for any help you can give.

  Mark

  Hi Mark,

  You can follow the example of configuration to:

  http://www.Cisco.com/warp/public/471/altigagroup.html

  Thank you

  Jean Marc

• Adding a custom VSA to a group - ACS unit

  Hello

  Using a secure ACS appliance 4.0

  I want to add a new provider of RADIUS and its VSA associated with the configuration of the ACS. This will be then returned in the authorization.

  I have already added the new seller and the VSA required through RDBMS. I can now see the new seller (supplier) RADIUS in NAP profile etc.

  However I can't seem to find a way that how to set the value of the SBA added? And assign it to a particular group? I can't find this anywhere VSA.

  Add an AAA client with "authenticate using the" Radius (vendor)

  Then go to Configuration of the Interface and select VSA to the user or group

  ~ Rohit

• ACS 5.5 external user with attribute internal

  Hi guys,.

  I wonder, if I'm using LDAP for external authentication, can use the internal identity attribute?

  for example:

  I create a user X, its password type is LDAP, but belonging group is "Group 1".

  can I set rules

  Idenitty group 'Group 1' allow access?

  or I do group mapping first?
  Thank you

  Kind regards

  It is possible to define an internal user whose password from an external store.

  In the definition of the internal user, select "Password Type" to be in the LDAP database and then set the rest of the definition of the user, including groups of identity, as you wish

• Doubt on the RA aaa using ACS 5.3 vpn user

  Hello

  I'm putting in place of the VPN on 8.4 ASA with 2 - VPNGp1 and VPNGp2. VPNGp1 groups users will access 1.2.3.0/24 and VPNGp2 users will have access to 5.6.7.0/24. User authentication will be done using RADIUS 5.3 ACS.

  On ASA, I configured pools VPN groups, ACL of VPN, IP, tunnel of groups and group for each group strategies.

  GBA, I created vpn-user1 and user2-vpn for each of the 2 groups.

  I don't know if some configurations more must be done on ASA and AC... Do I need to add new users - vpn-user1 and user2-vpn - on ASA, under each corresponding group policy, using the command political vpn-group?  Or I need to do something else on the ACS?

  Finally, how can I configure authorization and accounting for VPN users? I have to do this on GBA or ASA?

  Please advice.

  Thank you.

  Hello

  Authentication using radius aims to centralize user accounts and policies so that you will not have to configure these on the SAA. You must create a group of authentication servers that points to your ACS, then you will have to refer to this group of servers to your tunnel-group for user authentication queries will be forwarded to ACS for authentication. For accounting you will create an accounting server group and also assign to your tunnel group configuration.

  The GBA, you will need to create a network client that is ASA, and the shared secret will be the same. You create an element of authorization policy network who have the permission settings, or you can choose allowed access, which allows authentication succeed without any special authorization.

  You can debug the sessoin using crypto vpnclient 255 debugging to view the authentication stream.

  Using SSL vpn (anyconnect) for these sessions?

  Thank you

  Tarik Admani

• 4.2 of the ACS and ASA, authorized users in connection which should not

  ACS 4.2, AAA/Ganymede on my ASA configuration using. Currently any user to any NG can log in to the ASA, however, they cannot make changes without the enable password. We only want people in a NG to be allowed to log in to the ASA.  I'm not finding a good way to do it.

  You can create NAR:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/SPC.html#wp697095

  And then use it in the configuration of the user/group:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/GrpMgt.html#wp478900

  ---

  Michal

• Group Policy Client failed, the user profile Service failed

  I just restored to an earlier point because of the downloads to my son. After a few days, The Group Policy Client failed when trying to open a session administrator and the user profile Service failed under a different name. I can't do anything because this screen is the key for any software, including the internet. I went into the BIOS but it looks like no help. How can I get around the display of password or reset the computer.

  http://support.Microsoft.com/default.aspx/KB/189126

  "Microsoft's strategy concerning lost or forgotten passwords"

  Microsoft cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:

  http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspx

  Difficulty of a corrupted user profile

  After creating the profile, you can copy the files from the existing profile. You must have at least three user accounts on the computer to perform these operations, including the new account that you created.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  Ask them if you can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• ACS 5.2 - accounts User File Update does not work as expected

  Hello, I have a serious problem with the import of the fixed IP addresses to user accounts in ACS 5.2.

  Because this attribute cannot be migrated directly I try via "file operations--> update". I created the file update model, but entered IP addresses aren't imported - all other attributes can be changed without problem.

  If I try to "Add file operations-->" it works well, but I can't use this option.

  IPv4 address attribute in 'System Administration--> Configuration--> dictionaries--> identity--> internal users' is added correctly and appropriate field is not in user accounts.

  Do you have any idea what can be wrong?

  Hi Michal,

  Yes I submitted this as a bug recently. Sometimes after a migration from ACS 4.

  CSCtk05027 : custom fields for users after migration - import/update does not work

  Try to change one of your user input. Just add an IP manually it for example. Then do the update. She will work for this user, and it will update the ip address.

  The solution is to export all users of your DCC 5. Then remove it from the database and then to make an import file 'Add' instead of update. A bit of a silly workaround but the bug should be fixed in future patches (no information on that yet).

  Kind regards

  Nicolas

  ===

  Remember responses of the rate that you find useful

• ACS: using local as users aid ad

  Hello

  I have GBA 5.1 configured to authenticate users based on Active Directory. I have configured 802 cable. 1 x, with authentication enabled machine on ACS.

  When I have connection with the credentials which exist in the AD, it works very well. Then I have configured Windows authentication to request credentials (popup). But I have no network experience when I connect with a local account even though I have entered the correct credentials of AD.

  I want to do the following: for an existing account on the machine being authenticated (account no AD), ACS must check its local database and to successfully meet the authentication if he finds it, so that the user has network connectivity.

  I heard of sequence identity in ACS. But I still don't see the right configuration,

  any help?

  Thank you

  You can set up a sequence of identity which will first access the local database for authentication of the user and, if the user does not exist in the local database, it can then proceed to authenticate the user against the AD

  Configuration can be done as follows:

  (1) go to the users and identity stores > identity store sequences and press Create

  (2) enter a name for the sequence, then the password-based authentication method. Will see a list called "authentication and recovery research list of attributes. Hold the first internal users, then the AD1 in 'Selected' list Press 'submit' and the sequence will be created

  (3) select the sequence of the identity as the result of the policy of idnetity you use. for example, if you use the service of access 'Access to the default network' that is created by default go to:

  Access policies > Access Services > default network access > identity and select the sequence of the identity created in step 1) as the Source of the identity

• ACS 5.4 managing users

  I don't know if its possible, but I have a need to authenticate users via GANYMEDE management + ACS 5.4 against an another 4.2 (soon to 5.4) ACS server in a seprate area.  Anyone know if its possible and how?

  Hello Robert,.

  Unfortunately, Ganymede may be used to authenticate the management for ACS 5.4 you can select one of the following stores identity of ACS management authenticate.

  

  Store ID administrator internal

  Active Directory ID store

  LDAP ID store

  Work with administrative access control

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_system/5.4/user/guide/ADMIN_ADMIN.html#wp1089044

  Jatin kone
  -Does the rate of useful messages-

• Group ACS 5.3 removal Migrated_NDGs

  Hello

  I got the task to disentangle a 5.3 ACS server, devices are all imported from a former ACS 4.x server. All the devices in the "Migrated_NDGs" of the Group was created by the migration tool.

  Since I have no need of this group is safe to just delete the Group and the devices will remain in ACS?

  The only groups of network device I really need are the groups 'Rent' and 'Device Type'. Unfortunately, I don't have another server to test on and I do not want to delete the Group and find out that 700 + devices have also disappeared from ACS!

  You also wouldn't not possible to the device to export to CSV, delete them all of CSA, delete the 'Migrated_NDGs' group and then use the CSV file to import the devices return again, but less the Group column "Migrated_NDGs."

  Any help much appreciated.

  Mel

  I just tried this on my server and things worked well.

  If you delete the NDG has child nodes nodes, you may need to remove these nodes first, and when you do this, if there are devices that reference the node that you are deleting, then they get modified to refer to the root node. When finally only the root node is left then can remove the NDG.

  Having said that I recommend to do an export of network devices before starting a backup

  Would be interested to hear how you got and that things went well

• How can I create a network of groups ACS 4.2

  Hello

  I want to create a site wise groups in the ACS4.2 is possible or not, please send me the steps.

  Secondly I am having nearly 5000 network devices in my network, I have to manually add all devices or any method is to import the devices in groups

  Please let us now

  With regard to the control of network group following link

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.0/user/guide/n.html#wp342699

  About importing customer, you can use CSUtil database utility

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.0/user/guide/AE.html

  check the section user and aaa client import

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.0/user/guide/AE.html#wp417039

  M.

  hope that helps rate if it is