Guest access / traffic meter
I had the AC1900 for a few months and I also use access as a guest.
I was wondering if it was possible to limit the volume of traffic on the access of the guests?
No, it is not possible to place any cap bandwidth on guest access.
Tags: Netgear
Similar Questions
-
ConfigFree network traffic meter - what do the bars?
What does the bars up and down the network traffic meter in the configfree SP2 version?
Hello
Unfortunately, I m not sure what bar do you mean but the ConfigFree includes a feature to help clean with lots of useful information and helpful tips.
Please start the Configfree and press F1. Now, aid should start. -
Traffic meter is not available for JNR1010v2
I don't see the option under the advanced traffic meter. Can someone help with this...
Hello @mk_fox
Welcome to the community!
The Manual does not contain it, therefore, it does not support.
-
Select "Guest Access" router E1000
I have a Linksys E1000 router. The firmware is 2.1.00 7 build 30 August 2010. I would like to activate or enable guest access. I had to to 192.168.1.1 and find nothing there any access asked. To the wireless tab, the choices are basic setting wireless, advanced wireless, Wireless MAC filter and setting wireless security. Tfhank you.
I don't think that cisco connect will mess up the configuration.
You can change the password if necessary.
I don't think that lion is currently supported.
-
I think that when I bought this router, there is a guest access password... Right? I am such a novice to this if there is I don't know where to find it! Someone help and thank you!
Dian
Did you install Cisco Connect? This is where you can administer the guest account.
-
On a new XAC1900 after the installation of a home network based on IP fixed, with the main computer wired and all other 8 devices connected WiFi and no problem at all, I tried to use guest access.
I have configured the SSID with the suffix - comments and assigned a password. The SSID of the network is visible on the context of the WiFi but the connection will never be finalized.
The device of the guest, I checked that the SSID of new comments, within its DHCP system, have not been assigned the 192.168.33.XX expected but one IP address, from 169 etc, which corresponds to a provider (not Italian), other then mine. Of course I can not access or enter any password.
I contacted the support chat system that was very available, but unable to give a solution.
I checked the configuration several times and reinstalled the latest firmware, but no result even manually.
Failure is repetitive and the strange IP DHCP assigned to the Guest device is always the same (even after the days), showing that the data seem to be in the firmware. Also after firmware reinstall (verses 1.1.42.162280).
I have no more ideas!
Dear all, first thanks for your help. I finally found the solution. Here's how, for the benefit of third parties.
When I configured the primary network, as always I posted, several equipment (PC, iOS dev, Iphones, portable computers ipads, etc.), fixed IPs. They were assigned in the numbering according to the IP Address of the default router 192.168.1.1. That's why from 192.168.1.2 to 192.168.1.255. I does not take any care about toggle point control DHCP on the router connectivity, and it remained empty. During today muttering I thought: Let me see if activating only not the DHCP protocol to the main network could stop the DHCP server to the SSID of comments. And that's all! I had to explicitly enable DHCP in connectivity for the second (one guest) to exploit SSID.
Once again thank you all
-
Hi all
Hoping someone here can help me with this problem.
I have access as guest enabled on my router (firmware v1.0.4). E3200 Computers / laptops can connect, enter the password and use it very well.
When I try to get a smartphone connect (tried 2 iPhones, 3 Windows phones and 2 different Android phones), they are able to connect to the network, but even after the opening, a browser, will never get to the "hotel" Cisco, landing page, allowing them to enter the guest access password and connect to. By checking the connection on the phone settings, I see that they have acquired an IP address from 192.x.x.x correctly
Specifically, I bought this router so that I would not give my WPA key when people came and wanted to use their phones on my network.
Has anyone successfully got it works?
Thanks in advance...
Ok... After a lot of messing around and reset the default settings, I finally got to work and can repro the problem at will.
If the you are in a two router setup and the E3200 isn't the main router (i.e. in bridge mode), guest access will not work for smartphones. Once I swapped the roles of my two routers (i.e. made the main router E3200), guests for Smartphone access works as expected.
Don't know if a moderator / owner of the firmware feature reads the forums, but if you do, I consider this a bug.
-
App of Smart Wi - Fi and Guest Access + Bridge Mode
Hello!
I put my WRT1900AC as in Bridge Mode Access Point.
Everything is OK. But I identify some things not usable, when my router is in Bridge Mode. Such a thing is the creation of a guest for Wifi/guest access account. The Linksys App Smart WiFi offering however, but it does not work. When I put the guest access 'ON' it just stay naturally 'OFF '.
My question: is it supposed to be the case, or it may become in the future renewed with the software?
At the same time, I can change a lot of things with this Smart WiFi App, when my WRT1900AC is in Bridge Mode. Proven stuff: Wifi channel number change and change the filter MAC they work correctly.With all the Smart Wifi router when the clipping comments wireless value is disabled, because the guest network depends on DHCP for IP subnet isolation.
Is there a way to keep all the features of the WRT1900AC and the route of a primary network. It is an advanced configuration, because you must configure a static route in your main router and configure the WRT1900AC as a router not gateway.
Discussion of the example:
-
E3000 - guest access without password
Hello
I just installed a new E3000 wireless router and it works fine.
But I would like to give my guests access Internet without having to enter a password.
I know how to change the - password of comments, but it requires a minimum 4 digits password.
Is there a way to remove it?
Thank you
N ° there is no way that you can remove. The least we can do is to simplify the password such as 1234 or something.
-
Mode bridge E4200v2 + guest access: No DHCP IP assigned?
New E4200v2 2.0.37. In "Bridge Mode - DHCP" (i.e., Access Point router). Guest access is enabled & SSID broadcast. DHCP server is disabled, because my main Sonicwall router that provides related to major network 192.168.1.0.
PROBLEM = PC Client can see "-comments ' fine SSID and associate with her, BUT PC does NOT receive an address IP DHCP (i.e. 192.168.33.x) so the browser login page never appears and guest access does not work.
I'm sure it's related to DHCP. I'm assuming that the E4200 not receives or sends the comments with the PC client DHCP packets.
I saw guest access works on the old E4200v1 before so I know what it should look like.
Can anyone suggest any probable cause why my E4200v2 would not be providing comments DHCP addresses in the 192.168.33.0 subnet?
I don't have that 24 hours until I have to deploy 2 new E4200v2 at a remote site and after that it will be really hard problems because I will not be on this site.
Thanks in advance for expert advice!
I think I SOLVED!
Apparently, you need to ACTIVATE the two SERVER NAT & DHCP on the E4200, * before * you switch to BRIDGE MODE.
When I did this, access as guest - works great! Hooray!
I guess the E4200 needs to use these 2 services that run in the background to give the subnet access as guest & dhcp work assignments, which is a process hidden, once you're in Bridge Mode.
Wow, Cisco should really have a section of the guide user or KB article about it. Or at least when you click on Bridge-Mode a little pop-up asking you to ensure that these 2 pre - req for are enabled.
I'm moving now.
-
E4200: Guest access: no IP address on the routers of the waterfall
configuration:
2 wireless routers E4200.
LAN - LAN connected to a cable.
Router 1 is connected to the internet and has active DHCP.
Router 2 is NOT connected to the internet and has disabled DHCP.
Wireless is enabled on both of them with the same SSID.
account/guest access is enabled on them.
It works:
laptop connects to normal WIFI on Router 1--> internet works (IP: 192.168.1.150)
laptop connects to normal WIFI on Router 2--> internet works (IP: 192.168.1.150)
laptop connects to the WIFI router 1--> internet reviews works (after the screen connection in Internet Explorer) (IP: 192.168.33.108)
It does NOT work
laptop connects to Router 2--> internet reviews WIFI does NOT work
--> laptop does she not get an IP address
?
When I connect to the normal Wifi on Router 2, I get an IP address from the DHCP on the Router 1
But when I do the same with the Router 2 REVIEWS WIFI, it does not request an IP address from the Router 1
anyone ideas?
Thank you
comments network only works if the router is connected with its internet port. You cannot use the network invited on the router cascading with the LAN - LAN configuration.
-
Cisco ISE 1.4 - guest access
Hello world
We use the ISE 1.4, now, we want to use the guest access ISE Module. I created the user invited on portal of the sponsor. Now, how can I configure authentication and authorization policy? I want to verify the user.
Thank you.
Hello! I strongly suggest you check out the videos of laboratory Minutes on access for guests and all the rest too :)
http://www.labminutes.com/video/sec/ISE
Give those a try and let us know if you still need help.
Thank you for evaluating useful messages!
-
Sufficiently secure guest access?
Equipment: controller 2106, 1131AG, WCS 5.1.151
Internal users: connect to the network of 192.168.x.x as wired users. Authentication with a radius connected to the AD server. Use WPA2. Vlan1
Users invited: to connect to the controller through web-auth, DHCP on controller, Vlan2
Comments (in sequence) ACL rules:
1 allow SourceIP 0.0.0.0 / 0.0.0.0 IP Destination 192.168.1.5/255.255.255.255 (firewall)
2 refuse SourceIP 0.0.0.0 / 0.0.0.0 Destination IP 192.168.0.0/255.255.0.0
3. allow SourceIP 0.0.0.0 / 0.0.0.0 Destination IP 0.0.0.0 / 0.0.0.0
I understand that the suggested method for Wlan guest must be in the DMZ on a separate controller. As each location has its own firewall/internet connection I find this expensive solution, a nightmare administrative and probably exaggerated. My question is: is my pretty safe guest access with web-auth, VLANs separate and list access control?
The reason why using as establishing s ACLs on the wlc is because it's not really work as well according to your rules. ACL is better managed on the L3 interface.
-
I was now all day and fight a little bit. Someone at - it a doc very detailed on-site sponsor guest access approved with ISE 2.x and WLC code version 8.2.110.0.
I went through the process of implementation of the portals to the best of my abilities. I have my users who authenticate with ISE with PEAP for Wireless Corp. so I know it works.
How can I tell WLC/ISE which SSID I use for guest access? Also my customer get IP address, then it should be redirected?
I get this error on the WLC:
* apfReceiveTask: 20:37:31.136 Jun 13: % CSA-3-CLIENT_NO_ACCESS: apf_80211.c:4285 Authentication failed for the customer: c0:cc:f8:17: of: 25. ACL substitute incompatibility of AAA server.
And I see this in splunk:
June 13-15:50:28 10.20.0.60 June 13-15:50:28 ise01 CISE_Passed_Authentications 0000157854 4 0 15:50:28.428 2016-06-13-05:00 0006695154 5200 NOTICE Passed-authentication: authentication successful, ConfigVersionId = 90, IP = 10.20.63.14, DestinationIPAddress = 10.20.0.60, DestinationPort = 1812, UserName=C0-CC-F8-17-DE-25, Protocol = RADIUS, RequestLatency = 12, NetworkDeviceName = BNA-WLC2500-01, username is c0ccf817de25, NAS-IP-Address = 10.20.63.14, NAS-Port = 1 Type of Service = call check, Framed-MTU = 1300, Called-Station-ID=d8-b1-90-08-87-b0:TEST_GUEST, Calling-Station-ID=c0-cc-f8-17-de-25 Identify NAS = _GUEST, Acct-Session-Id = 575f1c94/c0: cc:f8:17: of: 25 / 23, NAS-Port-Type = Wireless-IEEE 802.11, Tunnel-Type =(tag=0) VLAN, Tunnel-Medium-Type =(tag=0) 802, Tunnel-Private-Group-ID =(tag=0) 142, cisco-av-pair is audit-session-id is 0a143f0e0000000f575f1c94, Airespace-Wlan-Id = 3, OriginalUserName = c0ccf817de25, NetworkDeviceProfileName = Cisco, NetworkDeviceProfileId = 8ade1f15-aef1-4a9a-8158-d02e835179db, IsThirdPartyDeviceFlow = false,
I can't reach the SSID from my iphone... but it looks like his tent. I suppose an ACL is wrong or a policy is wrong. I think that I have trouble with the VLANs that are pushed to clients.
Any help would be great thanks...
Could you send a screenshot of the configuration of the radius server in the WLC (detail page please).
Did you take a glance at the wlc/monitor clients if the ACL has been pushed for authenticated clients? What is the result?
Thank you
-
Guest access to computer specialist to resolve network problems
I work in an office with a server that is used by several people. I need to give our access outside IT consultant to my iMac and the network settings for my Time Capsule. I don't want to give my password for my iMac or the password that I used to set up my network in the environment of office because once the computer is in the system, he would have access to all the passwords in my keychain, but also confidential office files. Is there a way to provide access via the user system invited so that he can make the necessary changes the way my network is set up? Or is there another option other than the route of the guest user (aside from the obvious of meet me after hours of them log on?) Thank you in advance for any advice you can provide.
Is there a way to provide access via the user system invited so that he can make the necessary changes the way my network is set up
Sorry, but no. 'Guests' can not even "see" devices on the main or private network so the it guy / girl would have no access to devices on your private network. As such, what he / she would not be able to solve all the problems on your main network that you have.
Maybe you are looking for
-
I changed my apple ID and password. But my iPhone guard invites me to enter the password of old apple ID that no longer works. How can I get the phone to upgrade to the new ID and password?
-
It does not work with macbook air 2008! What should I do?
It does not work with the macbook air 2008 os x 10.5.8. What should I do?
-
you attempt to add as an attachment to an e-mail message block Thunderbird, why
I, ve been using Thunderbird with success on my HP Pavilion p6060a (Vista) including attaching documents (pdf or Word) for outgoing e-mail via the notice that appears when the words "join" or "attached" are inserted at the end of the project email. H
-
Presario C304TU does support SATA HD &; Win7?
Presario C300P / N:RE027PA #AB0Service C304TU This laptop has been owned by an old lady who used it rarely.I bought a second hand. It's like a new product. A few things I would change:1. its original HD is a 60 G IDE. The Commission supports a 120G
-
controls para jugar desde mi portatil no how con los juegos
Tengo unos controls usb para jugar desde mi portatil y no how con los juegos