GuestEndpoints ISE Cisco and licensing

Similar Questions

• Upgrading ise Cisco and licenses

  I nedd upgrade of version 1.1.2 patch 4 to 1.1.3

  the deployment is distributed so that the shared deployment technique should be used:

  http://www.Cisco.com/en/us/docs/security/ISE/1.1.1/upgrade_guide/upg_dis_dep.html#wp1052969

  the guide is quite difficult to follow as there are has some missing licenses information that can potentially cause downs of service:

  in particular my questions reguarding the guide are:

  -OUR license is registered on the primary node of PAN only-

  (1) main node of PSN deregistration "D": that it will use the license? the inherited (10000 points of termination) or if he loses the license completely and lock the network authentication?

  (2) when the node "B" will be struck out and will become autonomous what happens to its licence? It will be lost? and what will happen to the "D" node when added to node "B"?

  (3) when I move back node "A" (after the upgrade and the record to the node "B") to the previous state of primary PAN, it is said that the license must be reloaded in it was lost when adding it to the node "B"... and in the meantime? No node will not authenticate because the primary node is unlicensed?

  TY

  Giuliano,

  De-registered node will always use its own license, that is, it becomes autonomous box without knowledge or information about anything around her. Assessment or any license you provided with.

  Of license is made by admin active cluster node, depending on its license.

  Take a look on:

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId= CSCug04405

  I do not think that license needs to be recharged, but maybe it's just my memory doesn't serve me. I'll check that one again.

  M.

• ISE distributed deployment and license management

  Hello

  I have 2 x ISE-VM-K9 = licenses, and I want to deploy ISE mode Standalone with HA.

  IE, have 2 boxes Node1 and Node2 each hosting all three personas and closely located in 1 data center.

  so, I want to have a third box 3 node in a data center remotely (only for purpose of DR).

  What is the best way to design it.

  1. do you have nodes 1 and 3 in a host group and use as aaa primary and 2 secondary node

  2 have Node1 and 2 in a local host group, then the host of another entity 3

  I'm worried about the condition of licence of the 2nd option

  Any thoughts?

  concerning

  Sergeant

  Do you mean group of PSN node when you say "host group"?

  Licenses-wise, all the nodes in a deployment of share ISE licenses installed on the Pan

• Cisco MeetingPlace License Document upgrade

  Does anyone have documentation to modernize a MeetingPlace Audio and Web server port County license?

  Hi Michael,

  I don't know if that's what you're looking for? Good reading;

  On the load of Cisco Unified MeetingPlace License Keys

  You can add or upgrade license keys for Cisco Unified MeetingPlace functionality in your system, individually or all at the same time. You add or update the license through MeetingTime keys.

  For the license keys that you can add or upgrade files are available when you buy a new system, Cisco Unified MeetingPlace or upgrading to version 5.3. These files are loaded into your Cisco Unified MeetingPlace 8106 or 8112 when it was purchased.

  If you buy new license keys, Cisco sent to you as an attachment. Save the attachment on your local computer's drive. Place where you can navigate to it easily in MeetingTime.

  Loading of all license keys

  --------------------------------------------------------------------------------

  Step 1 tablet in the MeetingTime system, select the action of the system of Import Options.

  Step 2 for an Action attribute, click the values box. Choose Import to the system system options, and then click OK.

  Step 3 attribute to the name of the import file, click the values box.

  Step 4 to enter the file name of the license key file, accept the default file name or enter a different file name, and then click OK. (Use the control key, if necessary.)

  Step 5 click Run.

  Licenses are exported to the Cisco Unified MeetingPlace 8106 or server 8112 then added or updated day.

  Step6 restart the Cisco Unified MeetingPlace 8106 or server 8112.

  Step 7 to verify that the licenses have been loaded, run an MeetingTime license information report. (See section "License Information report" on page 4-6)

  Compare the amounts of license and license keys with the information that you entered in MeetingTime. If you see inconsistencies, load again missing licenses. For help, see "Technical support getting" in the Cisco Documentation by teleconference and support Guide.

  --------------------------------------------------------------------------------

  Loading license keys individually

  --------------------------------------------------------------------------------

  Step 1 locate the key option on the license document.

  Step 2 in the MeetingTime configure tab, select the System Options display.

  Step 3 click query, then click on the < or=""> button to locate the license key, you want to add or upgrade.

  Step 4 attribute to the number of licenses, click the values box. Enter the number of licenses for your system, and then click OK.

  The number of licenses must match the number that corresponds to your Cisco Unified MeetingPlace option key.

  Step 5 attribute for the button Option, enter the number of the option key.

  Step 6 click on save changes.

  Step 7 to load additional licenses, repeat steps 3 to 6.

  Step 8 reboot the Cisco Unified MeetingPlace 8106 or server 8112.

  Step 9 to verify that the licenses have been loaded, run an MeetingTime license information report. (See section "License Information report" on page 4-6)

  Compare the amounts of license and license keys with the information that you entered in MeetingTime. If you see inconsistencies, load again missing licenses. For help, see "Technical support getting" in the Cisco Documentation by teleconference and support Guide.

  This doc.

  http://www.Cisco.com/en/us/products/SW/ps5664/ps5669/products_administration_guide_chapter09186a0080333e0f.html#wp95293

  I hope this helps!

  Rob

  Remember messages useful rate...

• Configs ISE Cisco switch

  I guess Cisco ISE sends a redirect to URL to the switch and switch, it presents to the customer in the case of access comments get a redirect URL with acceptance of the user (guests and not wired) Page.

  My question is, do we need to configure the server http and https on the switches (both pleading and authenticator)?

  I don't know that it will take a confirmation, but just wanted to...

  I checked the configuration for the supplicant and authenticator of ISE switches, and there no where not mentioned this part of the config.

  http://www.Cisco.com/en/us/docs/security/ISE/1.0/user_guide/ise10_troubleshooting.html (a redirect to URL and possible cause problem is mentioned) - make sure that the config is necessary.

  http://www.Cisco.com/c/en/us/TD/docs/switches/LAN/catalyst2960x/software/15-0_2_EX/security/configuration_guide/b_sec_152ex_2960-x_cg/b_sec_152ex_2960-x_cg_chapter_010000.html

  (the begging and authenticator switch configuration) - mentioned anywhere in the configuration of http/https for the two switches.

  Yes, his need.  The http/s server in the swtich is used to retrieve the user http traffic and redirect the traffic to the CWA portal, or a registration portal device or even for the portal of integrated Mobile Device Management (MDM).  .

  IP http server

  IP http secure server

  The info below, I caught Cisco ISE for BYOD and book secure access unified.

  "Organization many want if ensure that this referral process to aid internal HTTP Server switch is dissociated from the management of the switch itself, in order to limit the risk of the user interacts with the intervace plan a switch of control and management."  This can be accomplished by connecting the two following commands in global configuration mode:

  active session modules IP http no

  "IP http secure-active-session-modules no".

• Cloning and licenses

  I have 16 laptops that I use for the safety tests.  They must be wiped out and reconfigured after business travel.

  We have been under XP SP3 so far, but we must move on to Vista.  Professional Vista licenses are available from our KMS on the field (that I do not have access to), but we do not know how this will all work together.

  When you destroy a domain Vista workstation, then reconnect it. will he get the same license?  In the same way that a machine can pull the same reserved IP address from the DHCP server, as it is MAC address has not changed?

  If anyone has any advice on this subject would be great, but I guess I would especially need a resource to learn all of the questions I should ask here.  Maybe a link that explains how Vista, cloning and licenses all work together.  Sorry if this all sounds vague.

  Check in the IT Pro TechNet forums forums - this kind of question is really beyond the assistance that we provide here because we support users who install Vista for single computer use.

  "Anonymous2xcfn" wrote in the new message: * e-mail address is removed from the privacy... *

  I have 16 laptops that I use for the safety tests.  They must be wiped out and reconfigured after business travel.

  We have been under XP SP3 so far, but we must move on to Vista.  Professional Vista licenses are available from our KMS on the field (that I do not have access to), but we do not know how this will all work together.

  When you destroy a domain Vista workstation, then reconnect it. will he get the same license?  In the same way that a machine can pull the same reserved IP address from the DHCP server, as it is MAC address has not changed?

  If anyone has any advice on this subject would be great, but I guess I would especially need a resource to learn all of the questions I should ask here.  Maybe a link that explains how Vista, cloning and licenses all work together.  Sorry if this all sounds vague.

• Cisco and Checkpoint VPN clients on a single PC

  Hello

  I'm in the following fix:

  I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.

  Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.

  According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.

  But I am not able to connect to my PIX, I receive the following error message:

  "Secure the complete VPN connection locally by the Client.

  Reason 403: failed to contact the security gateway. »

  When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.

  After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.

  After PC restart the Cisco VPN adapter is disabled later.

  I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).

  I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.

  After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.

  It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.

  Does anyone know of a workaround?

  Thank you

  Milan

  We had the same problem with some of our users who need to use the two clients to connect to customer sites.

  If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.

  We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in

  HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run

  After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.

  Hope that's a help

• Problem router Cisco and Checkpoint VPN

  Hello

  I couldn't establish vp from site to site between cisco and checkpoint. Can you please check the logs?

  Thank you.

  * 29 sept 08:17:22.627: IPSEC (sa_request):,.
  (Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
  local_proxy = 192.168.222.0/255.255.255.0/256/0,
  remote_proxy = 10.0.10.0/255.255.255.0/256/0,
  Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
  lifedur = 3600 s and KB 4608000,
  SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
  * 29 sep 08:17:22.631: ISAKMP: (0): profile of THE request is (NULL)
  * 29 sep 08:17:22.631: ISAKMP: created a struct peer X.X.X.X, peer port 500
  * 29 sep 08:17:22.631: ISAKMP: new created position = 0x88AD1AB0 peer_handle = 0 x 80000004
  * 29 sep 08:17:22.631: ISAKMP: lock struct 0x88AD1AB0, refcount 1 to peer isakmp_initiator
  * 29 sep 08:17:22.631: ISAKMP: 500 local port, remote port 500
  * 29 sep 08:17:22.631: ISAKMP: set new node 0 to QM_IDLE
  * 29 sep 08:17:22.631: ISAKMP: (0): insert his with his 88AF7D94 = success
  * 29 sep 08:17:22.631: ISAKMP: (0): cannot start aggressive mode, try the main mode.
  * 29 sep 08:17:22.631: ISAKMP: (0): pre-shared key found peer corresponding X.X.X.X
  * 29 sep 08:17:22.631: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
  * 29 sep 08:17:22.631: ISAKMP: (0): built the seller-07 ID NAT - t
  * 29 sep 08:17:22.631: ISAKMP: (0): built of NAT - T of the seller-03 IDexit
  Router (config) #n
  * 29 sep 08:17:22.631: ISAKMP: (0): built the seller-02 ID NAT - t
  * 08:17:22.631 Sept. 29: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
  * 08:17:22.631 Sept. 29: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1

  * 29 sep 08:17:22.631: ISAKMP: (0): Beginner Main Mode Exchange
  * 29 sep 08:17:22.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:17:22.631 Sept. 29: ISAKMP: (0): a Packet.o IKE IPv4 send

  * 29 sep 08:17:32.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:17:32.631: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
  * 29 sep 08:17:32.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:17:32.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:17:32.631 Sept. 29: ISAKMP: (0): sending of a CPVPN IKE IPvaccess lists

  * 29 sep 08:17:42.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:17:42.631: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
  * 29 sep 08:17:42.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:17:42.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:17:42.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE...
  * 29 sep 08:17:52.627: IPSEC (key_engine): request timer shot: count = 1,.
  local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
  local_proxy = 192.168.222.0/255.255.255.0/256/0,
  remote_proxy = 10.0.10.0/255.255.255.0/256/0
  * 29 sept 08:17:52.627: IPSEC (sa_request):,.
  (Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
  local_proxy = 192.168.222.0/255.255.255.0/256/0,
  remote_proxy = 10.0.10.0/255.255.255.0/256/0,
  Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
  lifedur = 3600 s and KB 4608000,
  SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
  * 29 sep 08:17:52.627: ISAKMP: set new node 0 to QM_IDLE
  * 29 sep 08:17:52.627: ISAKMP: (0): SA is still budding. Attached new request ipsec. (local Y.Y.Y.Y, distance X.X.X.X)
  * 29 sep 08:17:52.627: ISAKMP: error during the processing of HIS application: failed to initialize SA
  * 29 sep 08:17:52.627: ISAKMP: error while processing message KMI 0, error 2.
  * 29 sep 08:17:52.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:17:52.631: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
  * 29 sep 08:17:52.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:17:52.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:17:52.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
  * 29 sep 08:18:02.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:18:02.631: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
  * 29 sep 08:18:02.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:18:02.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:18:02.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
  * 29 sep 08:18:12.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:18:12.631: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
  * 29 sep 08:18:12.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:18:12.631: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:18:12.631 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
  * 29 sep 08:18:22.627: IPSEC (key_engine): request timer shot: count = 2,.
  local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
  local_proxy = 192.168.222.0/255.255.255.0/256/0,
  remote_proxy = 10.0.10.0/255.255.255.0/256/0
  * 29 sep 08:18:22.631: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:18:22.631: ISAKMP: (0): the peer is not paranoid KeepAlive.

  * 29 sep 08:18:22.631: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) MM_NO_STATE (peer X.X.X.X)
  * 29 sep 08:18:22.631: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) MM_NO_STATE (peer X.X.X.X)
  * 29 sep 08:18:22.631: ISAKMP: Unlocking counterpart struct 0x88AD1AB0 for isadb_mark_sa_deleted(), count 0
  * 29 sep 08:18:22.631: ISAKMP: delete peer node by peer_reap for X.X.X.X: 88AD1AB0
  * 29 sep 08:18:22.631: ISAKMP: (0): node-930113685 error suppression FALSE reason 'IKE deleted.
  * 29 sep 08:18:22.631: ISAKMP: (0): error suppression node 661004686 FALSE reason 'IKE deleted.
  * 08:18:22.631 Sept. 29: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
  * 08:18:22.631 Sept. 29: ISAKMP: (0): former State = new State IKE_I_MM1 = IKE_DEST_SA

  * 29 sep 08:18:22.631: IPSEC (key_engine): had an event of the queue with 1 KMI message (s)
  * 29 sept 08:18:27.559: IPSEC (sa_request):,.
  (Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
  local_proxy = 192.168.222.0/255.255.255.0/256/0,
  remote_proxy = 10.0.10.0/255.255.255.0/256/0,
  Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
  lifedur = 3600 s and KB 4608000,
  SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
  * 29 sep 08:18:27.559: ISAKMP: (0): profile of THE request is (NULL)
  * 29 sep 08:18:27.559: ISAKMP: created a struct peer X.X.X.X, peer port 500
  * 29 sep 08:18:27.559: ISAKMP: new created position = 0x85EDF1F0 peer_handle = 0 x 80000005
  * 29 sep 08:18:27.559: ISAKMP: lock struct 0x85EDF1F0, refcount 1 to peer isakmp_initiator
  * 29 sep 08:18:27.559: ISAKMP: 500 local port, remote port 500
  * 29 sep 08:18:27.559: ISAKMP: set new node 0 to QM_IDLE
  * 29 sep 08:18:27.559: ISAKMP: find a dup her to the tree during the isadb_insert his 88C1CE60 = call BVA
  * 29 sep 08:18:27.559: ISAKMP: (0): cannot start aggressive mode, try the main mode.
  * 29 sep 08:18:27.559: ISAKMP: (0): pre-shared key found peer corresponding X.X.X.X
  * 29 sep 08:18:27.559: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
  * 29 sep 08:18:27.559: ISAKMP: (0): built the seller-07 ID NAT - t
  * 29 sep 08:18:27.559: ISAKMP: (0): built of NAT - T of the seller-03 ID
  * 29 sep 08:18:27.559: ISAKMP: (0): built the seller-02 ID NAT - t
  * 08:18:27.559 Sept. 29: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
  * 08:18:27.559 Sept. 29: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1

  * 29 sep 08:18:27.559: ISAKMP: (0): Beginner Main Mode Exchange
  * 29 sep 08:18:27.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:18:27.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
  * 29 sep 08:18:37.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:18:37.559: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
  * 29 sep 08:18:37.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:18:37.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:18:37.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
  * 29 sep 08:18:47.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:18:47.559: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
  * 29 sep 08:18:47.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:18:47.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:18:47.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.

  * 29 sep 08:18:57.559: IPSEC (key_engine): request timer shot: count = 1,.
  local (identity) = Y.Y.Y.Y:0, distance = X.X.X.X:0,
  local_proxy = 192.168.222.0/255.255.255.0/256/0,
  remote_proxy = 10.0.10.0/255.255.255.0/256/0
  * 29 sept 08:18:57.559: IPSEC (sa_request):,.
  (Eng. msg key.) Local OUTGOING = Y.Y.Y.Y:500, distance = X.X.X.X:500,
  local_proxy = 192.168.222.0/255.255.255.0/256/0,
  remote_proxy = 10.0.10.0/255.255.255.0/256/0,
  Protocol = ESP, transform = esp - aes 256 esp-sha-hmac (Tunnel),
  lifedur = 3600 s and KB 4608000,
  SPI = 0 x 0 (0), id_conn = 0, keysize = 256, flags = 0 x 0
  * 29 sep 08:18:57.559: ISAKMP: set new node 0 to QM_IDLE
  * 29 sep 08:18:57.559: ISAKMP: (0): SA is still budding. Attached new request ipsec. (local Y.Y.Y.Y, distance X.X.X.X)
  * 29 sep 08:18:57.559: ISAKMP: error during the processing of HIS application: failed to initialize SA
  * 29 sep 08:18:57.559: ISAKMP: error while processing message KMI 0, error 2.
  * 29 sep 08:18:57.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:18:57.559: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
  * 29 sep 08:18:57.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:18:57.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  Router #.
  Router #.
  * 08:18:57.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
  * 29 sep 08:19:07.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE...
  * 29 sep 08:19:07.559: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
  * 29 sep 08:19:07.559: ISAKMP: (0): transmit phase 1 MM_NO_STATE
  * 29 sep 08:19:07.559: ISAKMP: (0): package to X.X.X.X my_port 500 peer_port 500 (I) sending MM_NO_STATE
  * 08:19:07.559 Sept. 29: ISAKMP: (0): sending a packet IPv4 IKE.
  Router #.
  Router #un all
  All possible debugging has been disabled

  The log shows main mode setup has failed.  See if this helps: http://www.itcertnotes.com/2011/04/ipsec-stuck-in-mmsasetup-and-mmnostat...

• Client VPN Cisco and Cisco Secure

  Cisco VPN client and the VPN from Cisco Secure client free to use with pix firewall software?

  Thank you.

  Hello

  If you have a valid contract to Cisco and you can get the following link:

  http://www.Cisco.com/Kobayashi/SW-Center/SW-VPN.shtml

  with your CCO login, then you should be able to use these customers at no cost because they are already covered by the contract.

  Thank you and best regards,

  Abdelouahed

  -=-=-

• Windows 8 store problem of cache and licenses

  Hello

  I recently bought a computer dell laptop Windows 8. I have a few problems in the windows store. I'm unable to update or check out all the new apps on the store. I continue to by clicking on the icons of application but nothing downloads and updates existing fail as well. When the troubleshooter in Windows 8 App running it is said that ' Windows store cache and licenses can be corrupt " I cleared caches and updated licenses both manually and through the application of the resolution of the problems, but the problem persists and I get the same message of the cache corrupted every time troubleshooting tool. Any help would be appreciated.

  Thank you

  Thank you very much for your reply, Prandeep :)

  I have no day my computer, nor have I received error messages. I could scroll down and browse the store but it was insensitive to all clicks I did, so I was not able to download/update anything

  When running the troubleshooter, I still got the message on corrupt cache even after fixing using the Troubleshoot utility.

  However, I have just above, came the problem. I have consulted the storage of the C drive windows folder and manually created a cache folder.

  I read the solution on a Web tech site and it worked for me.

  Will put in place a link here for all other people facing the same problem, as soon as I find them still.

• Decide on a Plan and License Type

  Hello

  I am currently working on the redesign of a website called www.TechEmirates.ae where I'm going to need pictures and high quality videos for the new design.

  I went on the website, reading about all the plans and licenses, but still not sure what I should go...

  Please visit the Web site. Your comments would be very appreciated.

  Thank you.

  Hi John,

  All the plans available and their inclusions/details are updated to Adobe Stock price and membership plan. Adobe Stock

  You can subscribe to the plan according to your requirement.

  I hope that helps!

  Kind regards

  Sheena

• What groups safety and licensing for developers and the bulk API?

  I am currently working on the API integration in bulk of our SaaS product to Eloqua customer instance.  General requirements include read a list of contact lists and then adding/setting day of Contacts in a list.  They sent us a list of groups of security and licensing options and asked us to the API user account and a user account temporary developer/Tester (check that data arrives intact in Eloqua).  Here's what I assumed from documentation and the discussions here, but someone can tell me if this is correct?

  User of the API (permanent)

  Required permissions: "Everyone," "Users of the API," "user - Marketing base" (to access Contacts or 'Advanced users - Marketing' if "custom objects" access?)

  License: no

  Temporary interactive user to developer/Tester

  Required permissions: "Everyone", "Basic Marketing - users" (and, possibly, 'Advanced users - Marketing' if "custom objects" access?)

  License: Eloqua Marketing Platform

  The other element that I see referenced in the code examples is the specifier "site" or "instance".  What format does it take, and where I can tell the client to search for it in their console Eloqua?

  Thank you

  Richard

  Hi Richard,

  Let's simplify things a bit...

  For the use of the API (one of them!), you should have User API and Marketing advanced - users.  This warranty covers the basics.

  Licensing should only come into play for things as endpoints to deliver.

  Until the 'site' or 'instance', it is the simple name of the company and is when the user connects to Eloqua.

  

  Hope that helps!

• What should I do before selling my CS4 install media and license?

  I uninstalled CS4 when I started my subscription of the CC.  I am now free to sell my CD to install CS4 and license or do I need to revoke registration after uninstall? How

  Assuming that you disabled the software before you uninstalled it, all that remains is to transfer the serial number to the buyer.

  Follow the steps in the link below:

  Transfer an Adobe product license

• I installed and licensed non-cloud versions of Acrobat and Photoshop, which, after several months, asking me to connect and start my trial version online. What's up with that?

  I installed and licensed non-cloud versions of Acrobat and Photoshop, which, after several months, asking me to connect and start my trial version online. What's up with that?

  even if you do not have the cc versions, follow these tips. Creative cloud applications unexpectedly back in the test mode. CS6, CCM

• vSphere 4.1 5 upgrade and licensing issues

  I currently have two server PowerEdge 2900. They each have two processors to 4 cores of each and 24 GB of RAM. Each server has a license in advance of vSphere 4 for 2 physical processors (1-12 cores). I also have vCenter 4 Foundation installed and licensed.

  I am looking to buy a new PowerEdge 620 with 2 processors, 8 cores each, and 128 GB of RAM.

  I want to do the following.

  1) upgrade the vCenter 4 to 5 license. Upgrade 2 CPUs with a value of 4 advance to 5 Enterprise vSphere vSphere licenses.

  2) update my installation of vCenter vCenter 4 5.

  (3) install ESXi 5 on new server PowerEdge 620.

  (4) migrate all virtual machines (guests) to a PowerEdge 2900 server to the new server 620.

  (5) Server Decomission the 2900 now blank.

  (6) keep the other server 2900 HA around and the low priority. VMs (I'm undecided as to whether I should upgrade to ESXi 5 on this one).

  Changes to licenses of 4 to 5 seems like a maze, but according to my calculations, 2 processors of licence 4 set to upgrade to 5, should give me enough for 2 CPUs and 128 GB of vRAM on the 620. It's my first time going through an upgrade like this, so I was hoping that someone with more experience could weigh in on this plan. I'm completely missing something, and he will be missed horribly? Any extra info / advice is appreciated.

  Thank you

  ... it is said that the old license get deactivated after the new ones are issued...

  Don't worry about this. Only old license on the portal keys will be disabled when you upgrade the key to v5. There is no license on your systems check, which will disable the host or vCenter Server.

  André

  PS: Although there is no verification of the license, it is your responsibility to ensure that the old and the new licenses are not used simultaneously. It would be a violation of the EULA.