H - REAP: difficulty to obtain the IP address for the client after loss of control
Hello
I have configured the following:
-H - HARVEST Wlan
-AP PM-HARVEST
-There is no trunk on the access port, so "Support Vlan" is disabled in the configuration of the AP. Because I want the Capwap data and the data on the same vlan REAP H of transit.
-J' have controller 5508 version 6.0.182.0
The first time that I connect with my PC for Wlan H-REAP, I get an Ip address
I see the DHCP from the AP request.
I can disconnect and reconnect several times with my PC, and I get all the time an IP address.
Then I disconnect the connection between the AP and the WLC, and I reconnect after a few minutes. (If the controller is again joined by AP)
Then, when I try to connect to the Wlan REAP H, it is impossible to obtain the Ip address. I don't see "dhcp - discover" coming out of the AP.
I have a message in the log of the AP: "customer 0018.de6a.3058 had 1 AES-CCMP TSC replays."
Similarly, if I reload the AP, the problem is still there.
The only way I found to solve the problem is to change something in the config of H-harvest-Wlan and apply it.
You have an idea?
Michel Misonne
I'll make a guess savage and say that you have WMM disabled on the WLAN... Enable WMM (supported) or upgrade to 6.0.196.0 (if WMM is disabled..)
Tags: Cisco Wireless
Similar Questions
-
AnyConnect disconnects the client after clicking on "accept".
AnyConnect disconnects the client after clicking on "accept". Our seller is using Windows Server R2 2012.
We see that the client passes authentication and connects then disconnects quickly without establishing a session.
Anyconnect version is 4.2.01035
Hi Carolina,.
You can see this windows server operating system is not officially supported / tested platform for anyconnect: -.
http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...
You can still install the anyconnect DART diagnostic tool and then check the errors on the newspapers.
http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...
You could probably run "debug webvpn anyconnect 255" to check the logs to see where the connection has failed
Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
Faced with the difficulty to obtain the logic...
Hello..
I have a table called rate that contains...
RATE
PERKM FROMKM TOKM
0 0 15
2 16 100
1 101 300
Now, I want to create a procedure with the distance as a parameter and fareamount as OUTPUT parameter...
I tired logical creation for her... I managed, but whenever a user enters a new record in the table of rates... the logic below does not work...
3 301 400
PROCEDURE get_fare_amount)
v_i_ndistance IN route_master.ndistance%TYPE,
v_o_nfareamount ON fare_Master
)
AS
CURSOR c1
IS
SELECT nrateperkm, nfromkm, ntokm
OF fare_master
WHERE v_i_ndistance > = nfromkm AND nactive = 0;
nrate NUMBER;
fromkm NUMBER;
tokm NUMBER;
tot (NO.2): = 0;
BEGIN
FOR temp IN c1
LOOP
IF v_i_ndistance > = temp.nfromkm AND v_i_ndistance < = temp.ntokm
-If distance between fromkm tokm n...
THEN
IF = 2 tot
-If total archives digitized is 2... to get the rate and km for previous record...
THEN
-For the 100 first kms use 2 perkm rate and for remaining kms we 1rs perkm.
v_o_nfareamount: =.
(((v_i_ndistance-tokm) * temp.nrateperkm))
+ (nrate * (tokm))
);
ON THE OTHER
v_o_nfareamount: = v_i_ndistance * temp.nrateperkm;
END IF;
END IF;
tot: = tot + 1; -To get the number of records
-To store values of the last record analyzed variables
nrate: = temp.nrateperkm;
tokm: = temp.ntokm;
END LOOP;
Dbms_output.put_line (' Total fare for ")
|| v_i_ndistance
|| "" kms:-".
|| « R. »
|| v_o_nfareamount
);
EXCEPTION
WHEN NO_DATA_FOUND
THEN
Dbms_output.put_line ('NO DATA FOUND');
WHILE OTHERS
THEN
Dbms_output.put_line (SQLERRM);
END get_fare_amount;The logic that I gave took:
-The rate for the first 15 km 0
-The rate of 2 for between 16 and 100 km
-The rate of 1 for between 101 and 300 km
-The rate of 3 km between 301 and 319Easy you need?
your sample data said rate = 0 for the first 15kms and not rate = 2 for the first 100 km as you said later.
For me, it would be:Scott@my11g SQL>exec :nbkm := 303 ; PL/SQL procedure successfully completed. Scott@my11g SQL>with fare as ( select 0 perkm, 0 fromkm, 15 tokm from dual union all select 2,16,100 from dual union all select 1,101,300 from dual union all select 3,301,400 from dual ) select :nbkm nbkm, sum(perkm*(least(:nbkm,tokm)-fromkm)) total from fare where tokm <= :nbkm or (fromkm <= :nbkm and :nbkm<=tokm) / NBKM TOTAL ---------- ---------- 303 373
373 = (rate0 * (15-0)) + (naturel2 * (100-16)) + (rate1 * (300-101)) + (revenu3 * (303-301))
-
difficulties in obtaining the files after backup
Hi I accidentally did something to my computer where my music files and image files and other files are past I tried to restore my computer to
a bygone era, but it does not give me a time to restore before I had the problem is there a way I can manually set to a date and time to a system
restoration to repair my computer thank you or something else I can do to get my stuff back (it happened as I tried to back up my files on my c drive)
You really need to do is run a recovery program to recover your files. I suggest you run it...
Recuva... http://www.Piriform.com/Recuva
You must save the files to one location other than the C drive. Do NOT use the recovery for this partition.
A hard drive external is the best places and is subsequently usable as a backup location such that you don't need to run a file recovery program again...
-
ORA-12170 of the client after installing 12102
I installed 12102 on Linux. In all my 11g install, our standard is to use dynamic record for each instance in the listener. Then you remove the listener.ora file which allows dynamic registration in 11g. We also use a listener shared by server... so I disabled the LOCAL_LISTENER parameter by alter system set local_listener = "; I have found no record of this has changed in the 12 c install. I found that a new process LREG registers the instance instead of PMON... but it's all working. My cases are recorded in the listener... yet I can't connect from a client or another server using the standard tnsnames.ora. What Miss me? Nothing don't watch even in my journal of the listener that is trying to connect...
ORA-12170 is one out of connection time.
From there, we can draw some conclusions
(1) your network service name WAS resolved to a connection string - left the tnsnames or a direct specifications. We know because the request got fairly far from actually solved in a host address and an attempt was made to send the request to the specified host.
(2) most likely, your application never made to the host. He timed out waiting for a response from the host, he would have received if the request had never got there. If the request had gotten to the listener, then failed for some reason, the error would be different.
So, what does this leave us with?
(1) the HOST = specification in your clien t tnsnames (or another method of specifying) is invalid, pointing to a non-existent host
(2) there is a firewall blocking the transmission of your client to your HOST
-
Connection with the client VPN for RV110W problem
Hi guys: I just installed a RV110W router to my small business and I try to connect via VPN from home client. I was unable to do so, no matter what I try. Relevant information:
1. I can connect to the router via remote very well management, so I know that the router is accessible from the Net.
2. internal address of the router: 10.81.208.1
3. active PPTP. PPTP server IP address: 10.0.0.1
4 IP addresses for PPTP clients: 10.0.0.10 - 14
5. two VPN clients added - one with PPTP, with the QuickVPN Protocol Protocol. Both are enabled (and Yes, I triple checked passwords)
6 encryption MPPE and Netbios active.
7 IPSec, PPTP and L2TP all active gateways.
8 VPN client: 1.4.1.2
9. computer: laptop running Windows 7 family (64-bit), with the firewall Windows is activated.
10 home network: 192.168.2.196
It is causing to tear my hair out. What Miss me?
Shannon
Hi Shannon,
I am pleased to see that you're progress.
Shannon Rotz wrote:
I changed the RM port to 443. Unfortunately, now I can't connect to the router via browser, either by remote management or from the local network - I get the usual "page cannot be displayed". How do I get back into the router configuration GUI?
You should be able to reach the GUI by typing https://192.168.1.1(assuming that you have not changed the default IP address) normally once you replace http (port 80) with https (port 443) the internal router web server automatically will redirect you to the https page if you type http. Open your command prompt and try to do a ping of the IP address of the router to ensure that it still meets this address
With regards to the VPN client: Up until I changed the port, the same error message kept coming up, i.e. "Unable to establish connection" (or something like that), with a list of possible reasons why it couldn't connect. Now the message has changed - I'm getting "Server's certificate doesn't exist on your local computer". If I continue trying to connect, then it says "Activating Policy", followed by "Verifying Network", then "The remote gateway is not responding. Do you want to wait?" This is definitely progress, since I never got this far before.
You are a quarter inch offline. If you look at the log.txt in C:\Program Cisco Small Business\QuickVPN Client, in my view, you will see "Failed to ping router remote VPN! This means that your PC is blocking the ping to the router response. Usually, if you look at this point the status of Client VPN in the router (first of all need to remote management) you will see that your user status is "connected." If the router thinks that the connection is established, but the PC does not work. You might want to try another PC at this stage to verify that it is indeed a problem with your PC. This problem is usually caused by the 3rd party software antivirus/firewall blocking the ping response. Microsoft Security Essentials can do this as well, so if you turn it off. If you do not have another PC to test from, call Cisco Small Business Support and ask a technician, try to connect to the lab. You can find the number to call here
On an impulse, I tried setting up a Windows VPN connection, i.e. created a new VPN connection in Network and Sharing Center, using a PPTP client ID that I had created. That connection actually worked, except for one problem: I can't see the remote network. If I could solve that problem, I'll just tell the other clients to use a Windows connection rather than QuickVPN.
Good thought. If you do not see the remote devices, make sure that they do not block VPN connections. (Windows or third-party firewall, antivirus, antispyware) With a connection, PPTP or QuickVPN, you should be able to go to run, type the IP address of the device that you want to connect to (i.e. \\192.168.1.101 ) and see the list of shared folders. After the PPTP connection is established, try to ping the address LAN IP of the router. If it is successful, try to ping a LAN device such as a network printer or a PC. Again, PCs may block ping requests if they have a firewall running watch so for this.
Answer please if you have any questions.
-
scalable design vcs-e for the clients of MPLS and internet
Hi all
I think of an evolutionary design of VCS-highway in a service provider architecture.
Some clients reach vcs-e across one MPLS network, another customer over the internet (each client with its own vcs - c).
I have a vcs-e with dual NICs and nat enabled.
VCS - e is a private network.
In this architecture, if I nat vcs-e in one public ip address, I can't inject the public IP address in the VPN client (clients use the address private, and anyway, they will not receive a public IP, MPLS and the internet). And I can't inject a private Internet ip address. In addition, every customer wants to use an ip address of vcs - e compatible with their plan ip... then maybe customer wants to use an address of 172.31.x.y and a B client an IP address of 192.168.x.y.
Best solution would be to nat vcs-e address in different ip address for each client / internet through the firewall, for example vcs-e 10.1.1.1 in 172.31.24.1 for the customer has, in 192.168.24.1 for client B and 80.x.y.z for the internet, according to the firewall context... but I'm not sure that I can do (I can? I think I can only the ip address of nat vcs-e statically 1 to 1).
I am attaching a figure illustrating the design of the network.
Any suggestion?
Hello
In your design, it is allowed to do NAT between VCS - C and VCS-E if you configure using links/box of course, which I think is what you plan to do. A nearby area will fail in this design.
If your customer can have a VCS - C on their private network and that you connect to your VCS-E through a NAT firewall as you describe as the "best solution". There is no need to NAT any return to the client IP address, since the VCS - C will make an outbound connection only for the VCS-E.
Robert
-
Insider source subscription. Could not retrieve the client certificate
Hi all
I created subscription source initiated between two Windows 2008 R2.
The source (client) cannot connect to the server. Logs on the client:
Send the request for operation to the destination machine enumeration and the server.corp.domain.com:5986 port
Authenticate the user using the Client certificate mechanism
User authentication failed. The credentials did not work.
Has received the answer of the layer network; status: 401 (HTTP_STATUS_DENIED)
WSMan enumeration operation failed, error code 5
Opens a session on the server.
Sending HTTP error to the client after a failure of transportation.
The HTTP status code is 503
The error code is 995Could not retrieve the client certificate
Send the HTTP 401 response to the client and disconnect the connection after sending the answer
The user authorization failed with error 5Authorizing the user
Authentication using client certificate with the client.corp.domain.com object is successfully
How to fix the error "unable to retrieve the client certificate?
Hello
Post your question in the TechNet Server Forums, as your question kindly is beyond the scope of these Forums.
http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer
See you soon.
-
How to get the IP address of the client when TCP connect on the server
How to get the IP address of the client when TCP connect on the server.
The only parameter obtained the login is the login ID.
I assume you are using "Wait of TCP on the listening port" on the server. This returns the remote address and port (like out in option).
-
BlackBerry Bold 9900 smartphones cannot obtain an IP address
Hello
I have a problem with the WiFi on my Bold 9900. I connect the WIFI but it fail to obtain an IP address and he done this for each connection, even for those already registered in my regard.
Does anyone have a solution or an idea to fix it?
Thank you
Mary
Yes, precisely. Enter an IP address.
On your PC open cmd command prompt and type ipconfig/all to get an idea of what is a valid IP address
-
IP address of the client issues
Just beginning to put an infrastructure in place of Cisco wireless, currently just test every thing. Here's my problem.
After you create a WLAN, bind it to the VLAN I can authenticate but cannot obtain an IP address.
Now if I bind the WLAN to the same VLAN access point is turned on, I can get an IP address.
I have the IP DHCP configured under WIFI as well as of interface, I tried with just by configuring it on the interface but no use
I tried proxy DHCP enabled and disabled
Also want to mention that the AP is connected to a switch and the switch port is configured as an access on VLAN130 port.
Hello
Please ensure that you allow the 109 VLAN on the trunk that connect the WLC to the switch.
HTH,
Tiago
--
If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.
-
Unable to see the option of ip address for esx3.5 by Vi client settings
I have two esx 3.5 boxes in a cluster and the two esx are in place and works well with hosting some virtual machines from each... and I'm able to power on all virtual machines and run.
an ESX is fine and no probs with it.
recently, there was some issue with the esx with its Ip settings... I provided a static Ip to the ESX and then I lost connection with this esx... I connected to tht ESX with ILO and del vswif0 and all vswitches and created a new and affect the service console port group DHCP ip address.
I followed these steps to d that:
xcfg-vswitch - a & lt; vswitch name & gt;
esxcfg-vswitch - L & lt; binding name rising NIC & gt; & lt; name of vswitch
esxcfg-vswitch - a & lt; PortGroup name & gt;. vSwitch
esxcfg-vswif - a vswif0 Pei & lt; PortGroup name & gt;. i DHCP
And now I'm able to connect the ESX Vi client... but when I go to the configuration tab, then to the networks... Properties and modification of service console... am able to see only two options uder general tab... its label of network and Vlan ID... There should be option for Ip settings is sttic and dynamic... Obtain ip automaticallya nd provide static ip... am able to see it all in my box first ESX... but not in this second one.
Hello
To reset the vswif there is no need to recreate all virtual switches. However, I don't like dynamic addresses for ESX. Eitherway, you should be able to do things always work out.
Regarding the differences, it could be in the way in which you created the vswif more than anything. You should still be able to switch from no DHCP if DHCP using DHCP, you will see all the information you want without going through the console. IP must always appear on the home screen however, does it?
Best regards
Edward L. Haletky VMware communities user moderator, VMware vExpert 2009, url = http://www.virtualizationpractice.comvirtualization practical analyst [url]
"Now available: url = http://www.astroarch.com/wiki/index.php/VMware_Virtual_Infrastructure_Security' VMware vSphere (TM) and Virtual Infrastructure Security: securing the virtual environment ' [url]
Also available url = http://www.astroarch.com/wiki/index.php/VMWare_ESX_Server_in_the_Enterprise"VMWare ESX Server in the enterprise" [url]
[url =http://www.astroarch.com/wiki/index.php/Blog_Roll] SearchVMware Pro [url] | URL = http://www.astroarch.com/blog Blue Gears [url] | URL = http://www.astroarch.com/wiki/index.php/Top_Virtualization_Security_Links Top security virtualization [url] links | URL = http://www.astroarch.com/wiki/index.php/Virtualization_Security_Round_Table_Podcast Virtualization Security Table round Podcast [url] -
My URL/address bar is missing, after the delicious update.
My drop-down search engine list is missing after the delicious update.
I can't understand how turn them back on, please advise, thanks.You are welcome
-
Is it possible to edit Firefox context menu to the standard address for the displayed Web pages? Often, I want to save an image on a page. Sometimes I "slip" and press "Send Image" when I want to "Save Image under" and sit and wait for the default page - send an email to come, then shut up, juggling its dialog boxes "are you sure". It is a way of trying to manage a blunder. Basically I want an element directly from a page by email. Is it possible that I can simply remove "Send Image" from the context menu?
It is possible with the Menu Editor extension:
https://addons.Mozilla.org/en-us/Firefox/addon/710 -
I stopped using Firefox when I became aware of a worm that had been prevalent. Recently, I used new Firefox instead of Internet Explorer or GoogleChrome, but now, I'm afraid that my computer may have been compromised because of China looking for characters in the address bar of Firefox, after that I registered on my gmail account.
This has happened
Just once or twice
Is see above story
If you see CJK (Chinese/Japanese) characters on the title bar of Firefox or Windows task bar, then that can happen if Firefox go to encoding UTF-16 for some reason any.
The extension Plugin RealPlayer browser Record (Tools > Modules > Extensions) has reported that causes this problem.
Be sure not to be confused with the RealPlayer plugin (Tools > Modules > Plugins) that plays media files.
The expansion adds some extra features like save multimedia files.You can disable/remove the extension Plugin RealPlayer browser Record in RealPlayer preferences (RealPlayer: Tools > Preferences > recording and download)
Maybe you are looking for
-
Satellite 1415: Two outputs screen is not possible?
I would like to use the coaxial video output as a second screen. Is this possible? An explanation, in the cases where I'm being unclear. In essence, I would like to use the coaxial output as a second monitor as seen with computers with two monitors a
-
Printing with Apple products on a HP Officejet 8500 wireless...
How will I know if my HP OfficeJet 8500 wireless is compatible with AirPrint for printing? P
-
Pavilion P6-2378: keyboard driver
Hello, I have just completed an update of Windows 8 and lost the on-screen order of volume that would normally show on the upper left of my office to win 8. I was wondering if someone could provide me the SoftPack containing the keyboard for my Pavi
-
I forgot my admin password, now I carnt change like thers no link to fgot password?
-
Sought to follwed and previous forum information steps to unload the upper and lower registry filters but none are included. Have you tried devcon in back and get the followin message "devcon is not recognized as a builtin or external operable progra