has no surface on compaq presario sr5710f reads error message hd535-2w analysis test

Similar Questions

• Upgrade a Compaq Presario SR5710F desktop computer

  Hello, I'm recovering because as far as I can get out my Compaq Presario SR5710F desktop... right now there windows vista service pack 2 32-bit. The processor is an AMD Athlon 64 dual core 4450e to 2.3 GHz with 3 GB of ram at 800 MHz. First of all, since the processor is 64-bit, I was wondering if a windows 7 64 upgrade is recommended... Secondly, I know that even though I have a 64-bit processor, the maximum capacity of ram I have is 4 GB due to the motherboard, but with this card mother, is possible to increase the speed of greater than 800 MHz ram (for the motherboard specifications are hard to find). I was also thinking to replace the graphics card, but what I am seeing that will probably require a different diet and I am on a limited budget. Any suggestion? Please take into consideration the fact that this upgrade is not for games etc, its a home computer that I'm trying to be as updated as possible for a minimal cost. I am realistic, however, and I know it's an old PC. More I am not worried about existing programs (32-bit), I certainly intend on a new installation

  RickCraw,

  Here are the specifications of your Compaq Presario SR5710F desktop computer and its card mother MCP61PM-HM (Iris8). According to the specification, this model has PCIe x 16 graphics card slot and a 250 watt power supply.

  (1) most retail graphics cards require a 300 watts or more big power supply system to work properly. Install a new graphics card to detail will require the replacement of power supply as well.

  (2) Yes, you can install Windows 7 64 bit on this computer. I recommend the upgrade of RAM at a minimum of 4 GB for use with a Windows 64-bit operating system.

  (3) NO, you cannot change the speed of the RAM. Your system is limited to the following specifications/configurations of memory;

  Dual channel memory architecture

  Two connectors DIMM DDR2 240-pin

  Supported DIMM types:

  PC2-4200 (533 MHz)

  PC2-5300 (667 MHz)

  PC2-6400 (800 MHz)

  Memory non - ECC, unbuffered

  Supports DIMM DDR2 2 GB modules

  Supports up to 4 GB (2 x 2 GB = 4 GB)

  Please send Bravo

• Compaq Presario SR5710F upgrade the video upon hearing the motherboard cannot handle high power supp

  What is the best graphics card upgrade which can my Compaq Presario SR5710F can support? I'm ready to upgrade the power also, but hear that the motherboard do not put anything above 350 watts regardless of power.

  You can install any PCIe x 16 video card you want. The limiting factor is going to be the power supply. More power the longer video card POWER supply. About what you hear about the motherboard, I found nothing to that effect. To qoute request-leo,' I heard a matter of concern that a power high power can somehow 'forcing' the power on the computer, resulting in overheating and burnout. Nothing could be further from the truth. A power supply provides power in response to the need; It does not matter where power grow. If your computer only needs 100 watts, then a 500 Watt power supply will only provide 100 watts. Why have a 500 Watt power supply? For the use of 'pic' (sometimes material will require 'sudden' power, as at the beginning upward or under heavy load) and for future expansion. »

  It is better to have too much power too littleand to get the right size. By that I mean the physical size - come in many standard sizes out there, and they are not interchangeable.

  Frank

• Task Scheduler error: "an error has occurred for task reminders - portable home. "Error message: the specified account name is not valid.

  HelloW everyone,

  I changed my name to the laptop and now every time I have lunch Planner task, I receive the following error message:

  "An error has occurred for task reminders - portable home. "Error message: the specified account name is not valid.

  I also have the problem with restore points, so these two issues relate to eachother? How can I solve the problem of the user name.

  Any suggestion and help appreciated

  Hello

  You can check out the link and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-performance/odd-Scheduler-error-messages/a487d70b-61c9-499F-ae15-ac903d6174eb

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following windows Help article.
  Back up the registry
  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

• Installation of an EVGA in a Compaq Presario SR5710F 5600GT

  Hello, users of the forum!

  A few moments ago, I bought a Compaq Presario SR5710. I noticed the horrible integrated graphics card (nforce 430 motherboard w / GeForce 6150SE) supplied with the machine, so I'm interested to the EVGA 5600GT graphics card as a replacement. However, I don't know if this replacement will be compatible with the motherboard and its power. A lot, I would like to know if I'll be able to use this graphics card with my current SR5710F. Thanks in advance!

  goldblattster

  GB, here is a link to a power supply which is highly recommended on this forum:

  http://www.Newegg.com/product/product.aspx?item=N82E16817139008

  Another good brand is OCZ.  I used the PSU for more than two years.  They fully support their products.

  Please check the measurements of your current diet and news for you ensure that she never goes in the space provided.

• An on-screen volume indicator has disappeared from the Compaq Presario running Windows 7

  I have a Compaq Presario CG56 with Windows 7 64 bit.  All of a sudden the volume display on the screen (NOT the taskbar icon) does not appear when I adjust the volume.  I don't change anything on the computer.  Any ideas?

  Hi again,

  If you do not want to install / uninstall anything, then you can restore your system to the point where you remember that visuals work ok.

  Resources:

  How to do a system restore in Windows 7

  When it will not work then you will need to use the solution to my previous answer.

• Compaq Presario CQ57: bios error 501

  What should I do to get rid of this problem?  Please help me someone.

  Welcome to the community of HP @ANAKONDA support,

  Thank you for joining on the HP's Support Forums! It is a great place to ask questions, find solutions and get help from others in the community! I read your post on the Forums of HP Support.

  I wanted to join you and help! I understand that you have a problem with an APPLICATION (501) BIOS ERROR on your Compaq Presario CQ57 laptop PC.

  Remove all USB devices. Disconnect all non-essential devices, because they can cause some problems.

  Try starting your laptop normally after having disconnected all. If that does not solve the problem, please continue with troubleshooting.

  The next step would be for you to try to restore the BIOS. You will see that the document says:

  If the BIOS of your laptop becomes corrupted, and a failure to upgrade the BIOS or damage caused by a virus, the computer can display all the following symptoms:

  • The computer displays the error message from the BIOS APPLICATION ERROR 501.

  After restoring the BIOS see if you can start the computer normally.

  Thank you for your participation in the Forums of HP where we want to help you as well as others who may encounter a similar problem that you have. Remember to mark this message as an acceptable Solution if it solves the problem for you.

  To show recognition for my efforts please click the Thumbs Up below.

  If you need assistance, I would be more than happy to continue to help you. Please re-post with the results of the resolution of the problems. Could you please also provide your model number (How can I find my model number or product number?)

  Have a wonderful day!

• Installation of Java has wiped out everything on the computer receiver error message: "windows-delayed write filed" hard drive failure ' x 5

  I installed java and it wiped out my computer, no program, no picures, no parameters on the left? He even wiped my restore points.

  I tried to restore to the point of installation of java, but alas nothing has happened, now I get all these boxes warning "windows-delayed write filed" hard drive failure ' x 5 and also warning mean my HDD is in peril of the personal data.  This single icon left on my desk is the internet explore and internet runs very slowly, I am reluctant to sign something incase, there a virus or something.

  Please help me!

  Hi Carolinelightfoot,

  This error message occurs when the system could not read and write data to the registry file. The error indicates a problem with the registry.

  Method 1:

  You can run a Checkdisk to see if there are drive errors that can cause this problem.

  Check your hard drive for errors

  Note: When you run the disk check, there is a chance of losing the data that you can take a backup of important data before you run checkdisk.

  Method 2:

  You can also try to boot from a full version of Windows Vista installation disc and try to perform a restore of the system to WinRE (Windows Recovery Environment)

  What are the system recovery options in Windows Vista?

  Hope this information is useful.

• Windows backup / reader Error Message

  When I try to create an image of sytem, I get a Windows error message.  Legend of error: backup of the files.  The error section reads as follows:
  The reader \\?\Volume{4abe5988-c73f-11df-8bbd ... contains errors.  The error text is:

  Windows has detected corruption of file system on \\?\Volume{4abe5988-c73f-11df-8bbd-806e6f6e6963}. You should check the drive to the case before you can restore it.

  Check the drive for errors IGNORE OK

  By clicking on "Check the drive for errors" a new dialogue "Check Disk... "automatically opens with options to resolve the errors of system files and Scan for and attempt recovery of bad sections.  One or two control options and clicking Start Windows returns a new error: "Windows could not complete the disk check.

  To create this situation, I take the following steps:

  1. start > Control Panel

  2 backup and restore

  3. create the system image

  4. Select the backup location > OK

  5 backup C:\ (System) and RECOVERY (System) > next

  6. the error occurs.

  If I ignore error ther, the backup image is created, but because of this error, I'm not very confident that it will work if necessary :-(

  Background:

  1. I created a system image on 17/12/12 without problem (no error)
  2. I have all the windows of critics and other updates of software installed MS (Windows last updated 11/01/2013)

  3. I tried a restore point from before the windows update and it failed.

  4. my PC has been partially infected with "System of Progressive Protection" malware a 09/01/13.  I caught it starts to open the closure of the PC.  I ran MalwareBytes, Advanced System Care, MaAffee Security Center, Super Anti-Spyware, ChkDisk, sfc scannow and two applications separate from tune-up Dell PC with Global hard drive Diagnostics.  All indicate that the virus has been removed successfully, and that there is no error in drive on my PC.

  5. I find the Volumn number register (is not here).

  6. I did the recommended deletion of 'System of Progressive Protection' blogs McAffee and MalwareBytes.  Both indicate that the virus has been removed.

  7. I tried to create a new account administor and creation and the image with the same error.

  I don't know whether or not the error message I see is caused by the virus. However, I'm fairly certain, and is so my Dell rep of tech support, the "drive" appears in the error message does not exist.  Anyone know what else I can do to eliminate this error?

  Thank you.

  ,

  I came across a solution.  It seems that the problem is due to my ignorance.  Three years when a particuation my hard drive I have not assigned a drive letter to the "ROCOVERY' player intalled by the OEM.  {This "volumn" has ID: \\?\Volume{4abe5988-c73f-11df-8bbd-806e6f6e6963}.

  Somehow this volumn developed a file system error.  I used disk management to assign a drive letter to this volumn and then, I could check with ChkDsk.  He corrected the mistake and now I can make a system image without this error occurring.

  Thank you.

• Satellite A110 - SD card reader - error message code 10 this device cannot start

  I have a number of cards memory SD, who used to work with the machine's card reader but now gives a code 10 this device cannot start, error message - is this a problem XP - ideas appreciated...

  Hello

  Well, it sounds to be really an XP problem. Eventually he s corrupt registry entry.
  Just try to remove the SD card from the Device Manager reader, and after restarting again try to install it again

  Next

• 34957172.exe has stopped working and was closed. Windows error message

  Since the installation of Service Pack 2 for Vista, I receive the following error message that causes my computer to freeze - "34957172.exe has stopped working and was closed.  A problem with the application to stop functioning properly.  Windows will notify you if a solution is available. "How can I solve this problem

  Hi SherriTeille,

  (1) what is you receive the exact error message?

  (2) when exactly you get the error message?

  Method 1: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 2:  Put the computer to boot and then check if the problem persists

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link

• How can I get the pc mode f11? Compaq presario SR5710F w / vista

  system returns to F11 recovery on each boot menus. How to start vista normally?

  Well, we finally had rebuild the system. First, we used one temporary version of Windows XP on another HDD to save the data of the disk of Vista unbootable. Then we did a clean install of Windows 7. Later the client retrieved the data from registers it on the temporary disk of XP.

• CD read - Error Message: Build with Autorun CD Studio has stopped working.

  I am running Vista and have had no problems reading CDs or DVDs.  However, I have a CD of my teacher built with Autorun, who will not play on my computer.  I tried 2 different copies without success, but the 2 same CDs play on all computers in the school and on the computers of the other students.  I have Microsoft Powerpoint and Word, that are required to read the files on the CD. When I insert the CD, I get the opening menu, but when I try to select any specific topic, I get the error "Build with Autorun CD Studio has stopped working" message.  I have downloaded and run the Microsoft FixIt! Program diagnosis/troubleshooting of Microsoft Support, but he could not find any problems.  I need this CD for upcoming classes and don't know what to do?

  Hi pinkpugsy,

  1. are you able to browse the contents of the CD using Windows Explorer?

  It looks like Autorun CD Studio program is defective. We recommend you to uninstall and reinstall the Autorun CD studio software on your computer and check the difference.

  Note: before you remove the software, make sure you have the Setup file of software with you.

  Step 1: Uninstall or change a program
  a. see Uninstall or change a program
  b. Once you have uninstalled the program, restart the computer.

  Step 2: Install the Autorun CD Studio software. Once you have installed the program, restart the computer and check the difference.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Compaq Presario CQ57: Parse error at line 1: unexpected end of file. C:\Program Files (x 86) \airtell internet\config\UUConf

  My computer does not have to install a mobile operating system!

  I need an answer! Please, I beg you.

• Error on starting of my Compaq Presario CQ57-339WM error on the box that says

  I get an error when I boot. Said HPQWUTILS. EXE = No disk there is no disc in the drive. Please insert a disk into the drive. then there \device\hard disc 1\ DR1, the bottom row says Cancel try again continue everything in boxes. If I hit Try again 5 times the system appears and works.

  Hi Lejunc,

  1. what operating system is installed on the computer?

  2. were there any changes (hardware or software) to the computer before the show?

  This error occurs due to Proxy HPQuickWeb.

  Click on the link below and see if it helps.

  http://h30434.www3.HP.com/T5/notebook-operating-systems-e-g-Windows-8-and-software/hpqwutils-exe-no-disc/m-p/1134331#M84333

  WARNING of THIRD PARTY SOFTWARE: Using third-party software, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  Hope this information helps.

  Please let us know if you face any issues.