HDMI monitor receives no signal - worked before

Similar Questions

• How to fix a pc when the monitor receives no signal?

  I have a hp m9000t series, recently, I do some changes in the BIOS and after the record setting and the release of the bios computer restarts, but monitor losing signal. After many restarts still no luck still blank monitor. How can I fix my pc without monitor get a signal? BTW... I'm sure that all devices are working correctly. It is in any case to restore the setting without the bios screen?

  Hello

  Shut down the PC, remove the AC power supply.  Follow the procedure to clear the CMOS, which is under the heading "Compensation bios settings" to the bottom of the page on the link below.  You must make sure that you put yourself in the Earth or wear an anti-static strap to prevent damage to components on the motherboard.

  http://support.HP.com/us-en/document/c01077641

  I hope this helps.

  Best wishes

  DP - K

• 2nd monitor receives no signal

  I recently bought a HP 2511 x monitor to extend my desktop.  I use it as my main screen with my old monitor as my second screen.  They have worked very well for two days since I plugged the but just now after having to restart my computer the second monitor no signal.  My computer is a HP HPE-400y with an ATI Radeon HD 5450 video card that says it's working properly.  Any suggestions would be greatly appreciated!

  Hello

  Try to swap the two monitors and cables have a for one and see if the question follows the cable of the monitor/or rest on the same video card port.

• HDX18 external monitor receives no signal

  My HDX18 connected to an external monitor.  Powered monitor 'no signal' message is displayed on the monitor.  It was a working arrangement and has recently stopped after disconnection and reconnection of the monitor.

  Try to connect the monitor to another machine to make sure that the monitor is working.  Try to attach another monitor to your machine.  Recently point any driver software, including video?  Tried the function and the combination of F keys for switching between external, internal and two screens?

• Windows XP used... TV being used as an external monitor receives a signal from the laptop, but displays no office or something more

  My Samsung DLP is connected to my laptop and it shows the logo of the computer but I can't get anything else, such as the desktop... any help would be appreciated

  Hi jayvee53,

  1. don't you make changes before the show?

  We recommend that you adjust the size of the screen in digital and analog Mode in Windows (resolution setting)
  If the image is too large or too small, very probably, you must set your computer to optimal resolution screen and/or the optimal frequency (vertical frequency) to your TV.

  Step 1: To set the optimal resolution, follow these steps:
  a. Click Start > settings > Control Panel.
  (b) in the Control Panel window, double-click display. Display of the dialog box is displayed.
  c. click on the settings tab in the display dialog box. The settings dialog box is displayed.
  d. in the screen resolution section, move the cursor to the optimal resolution for your TV and then click OK.
  e. in most of the cases, the screen goes out for a moment or two and then re - appears in the new resolution, display a dialog box asking if you want to keep the new setting.
  f. click Yes.

  Important: The Optimum resolution for your LCD TV should be included in the section display PC of your manual.

  Step 2: To set the optimal refresh rate, follow these steps:
  a. Click Start > settings > Control Panel.
  (b) in the Control Panel window, double-click display. Display of the dialog box is displayed.
  c. click on the settings tab in the display dialog box. The settings dialog box is displayed.
  d. click the Advanced Options button at the bottom right of the dialog box.
  e. in the dialog box that appears, click the monitor tab.
  f. on the tab monitor in the monitor settings box, click screen refresh fall down, then 60 Hertz.
  g. click OK.

  Note: We recommend that you also download and install the latest video card driver on your computer.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• My ability to thunderbird to receive the mail suddenly stop and it worked before. What can be the reason? Now, I'm not able to receive all e-mails.

  My ability to thunderbird to receive the mail suddenly stop and it worked before. What can be the reason? Now, I'm not able to receive all e-mails.

  This forum is the official place to support Thunderbird. There is no phone support.
  If you think that this helps to explain the problem, you can add a screenshot to your message.
  You are supposed to follow instructions and suggestions that precede.

• Qosmio X 500 - enternal monitor gets no signal

  Hello

  It s come a time where I need an external monitor to extend my desktop. I plugged in one of my monitors to the laptop. Qosmio he sees but the screen does not receive a signal. Tried a 2nd monitor and it does the same thing, said cable not connected on 1 and power save on the other.

  I tested the monitors and the cables on another laptop in the House and they work fine then it s down to the laptop. I tried hdmi on tv and that works fine, seems to be just the vga as the laptop see the monitor when connected does that mean the vga port is ok?

  And could be something else? Any advice is welcome a soon.

  John

  Your ad is a bit confusing to me and I do not see a clear structure. What you tested and the result is not clearly described.
  > I ve tried hdmi on tv and that works very well
  How did you test? With your Qosmio or what?

  Anyway, it is not easy to say what the problem is here. Try to test it again with TV. Connect your Qosmio to the TV using a HDMI cable, switch to HDMI to the TV port and use the FN + F5 key combination to switch between an LCD and TV screen.
  It work?
  > therefore seems to be just the vga as the laptop see the monitor when connected does that mean the vga port is ok?
  How to understand this? Desktop appears on the screen when you use the VGA port?

• TouchSmart 610 unable to receive the signal from the configuration box

  I have HP 610 TV tuner equipped touchsmart all-in-one.  TV work very right up until a few days ago, when I couldn't have a signal from the cable box.  Box has changed and cables without result.  Tried a HDMI cable, but can't find the source selection.  Hung a small tv for the area with a perfect image, so that the excluded the cable/box issue.  Very grateful for any suggestions/advice/help.  Thank you!

  Hi again SuZQT,

  It is good to hear from you!

  To enable your system to receive a signal once more, I recommend you to return your system to a previous restore point before the problem occurred. This can be done by following the steps described in this document on using Microsoft System Restore (Windows 7).

  Please re-post with the results of your troubleshooting, and I look forward to your response!

  Concerning

• How to connect 2 crush & 1 HDMI monitors

  I'm trying to connect a video monitor HDMI as well as my two screens normal thunderbolt to my MacPro 2013, but only two on three monitors show no signal (if I disconnect one of the Thunderbolt monitors then the HDMI monitor will start working).

  My Mac Pro (2013 8 core) has two over-pants D700 AMD graphics cards.

  I want to use my HDMI monitor purely as a video monitor, video editing

  Thank you in advance for your help!

  Make sure that you have all the screens on the same bus Thunderbolt.

  https://support.Apple.com/HT202801

  "This means that if you use the HDMI port, then only use one of the ports Thunderbolt two down (Bus 0).

• Satellite P20-102 - receiver remote not working do not after running recovery CD

  Hello

  I am running Windows Media Center Edition and on my laptop Satellite P20-102.

  I recently needed to run the recovery CD, the process went well except that my box of external remote control receiver provided with my laptop no longer works.

  The box works with XP Media Center Edition and the remote control before I ran the recovery CD. The receiver is detected and installed on the computer when it is connected and recognized in device like a USB Serial Converter Manager. The inner light flashes about 4 seconds. When you press a button on the remote control light both in the housing of the remote control receiver if it receives the signal.

  I guess it's a software problem, I can't find any information on the installation of the receiver or all the drivers for it.

  Any help would be greatly appreciated.

  Kind regards

  Paul

  Hi Paul

  I also P20 but unfortunately without MCE. I can't give you any help, but in my opinion, you should try to contact Toshiba hotline in your country. Maybe it's possible that one phone call can help you manage this matter in the right direction.

• Computer will not receive Comcast Digital adapter (DTA) receiving TV signal

  Until recently I had used a tuner for my computer (and Media Center of course) to access all cable channels I ordered via Comcast. In other words, until Comcast made the switch to digital, which means I need a decoder adapter digital transport (DTA). After the switch, and before that I'm the DTA, I was able to receive broadcast TV channels, but not basic cable (for evidence, I was able to record a show on a channel on my DVR).

  I got one of the Commission yesterday and followed the instructions to a T. Among these non-tamponnage my cable output directly from the computer and to the contrary put through the DTA, then a coaxial cable linking DTA to the computer. Unfortunately, Media Center told me that I had no signal TV at all (and therefore that I couldn't even check how worked the DTA). Comcast technicians told me that the box has been activated and it worked, so the problem is probably the communication between the Commission and my PC. The PC is not received the signal from the DTA, and I have no idea why.

  Some features:

  Windows XP 2002 OS, running on PC Gateway GM5066E, Media Center came with the machine (purchased in 2006/2007 or most), built in TV tuner, I have all the equipment/remotes...just IR no TV signal

  Any help you could give would be great!

  According to my instructions, the IR blaster NOT plug on the back of the DTA.
  The only thing that plugged into the back of the DTA is the COAXIAL cable from the wall and
  the power adapter cable. and you do NOT use the cable/IR extension which has been
  provided with the DTA. See point #5.
  You may need to buy a cable blaster if it did not come with the gateway.

  is that what you have:

  http://support.gateway.com/s/Accessor/104220/104220mv.shtml ?

  Sticky end cable blaster must be glued on her go to the DTA,
  covering the eye of the receiver. the other end should be connected to the foregoing
  accessory that must be plugged into a USB port.
  Still, you can't use the IR blaster extender cable supplied with the DTA and
  nothing branch at the rear of the DTA, other than the coaxial cable and power supply.

  On Friday, August 6, 2010 16:52:39 + 0000, jtaberle wrote:

  The make and model of computer are in the first post (gateway GM5066E running XP 2002). I use the WMC remote supplied with the computer. As I said, it works fine except for changing the channel (interaction with the DTA).

  Through the slit in the IR, I mean plug it into the back of the DTA to the IR receiver (NOT the IR USB receiver that I use, the piece that came with the DTA).

  Barb Bowman

  http://www.digitalmediaphile.com

• A00 receives no Signal

  Hi, I can't get this monitor to receive a signal from my computer.  He however appear in Device Manager and it even found an updated driver for it and installed it.  Which means that the computer records the device connected, but it still receives no signal?  That eliminates a problem of bad cable?  It eliminates a bad port problem?  Etc...

  I plugged on a couple of different computers as well but still nothing.  I also connected another monitor in the same port on the computer, so I know that's not the computer.

  Thanks for any help, appreciated.

  [Solved]  I just wanted to post this information for someone else who could get this problem.

  I finally had the chance to try with a different cable and it works now.  So, even if he was in communication with the computer, which indicates that the cable wasn't working at a certain level, it was always 'bad '.  Somehow, he was not able to deliver an image even if it was transmitting data.

• My Toshiba 22EL833G ceases to receive the signal from my Satellite U300 - 13H

  Hello

  When I connect my laptop to the TV and turn it on, I first receive signal at the entrance to loading windows, but when it comes to enetring my password, stops the TV receives the signal. I'm sure that problem comes from the TV as when you use another screen, everything is ok.

  Does anyone know what I can do?

  Thank you all for your time

  Hello

  What password do you mean exactly?

  If you think the troublemaker is your TV then you're in big trouble.
  Why? Because there's not a lot of parameters that could be changed.

  You must ensure that you use HDMI right channel (I assume you are using HDMI connection). From my point of view, it is one and only parameters that must be set for television.

• Cannot receive TV signal from my cable box to my Qosmio F20 numerci

  Hello everyone, I just bought a new laptop Qosmio F20, everything works well except the tv tuner.
  I tried to plug in a cable SCART, a yellow cable / red / white and a cable to an antenna in my cell phone and my digital cable box (Atlanta 5400) but I can't receive any signal.
  The best I can get is one second of the sound of the first string on each channel in windows media center.
  I work as a computer technician, but impossible to find a solution to this problem, is there something special to do to receipt the TV on my laptop?
  Hope to hear soon, thanks to all in advance

  Hello

  Have you used the Qosmio Player or MCE?
  As far as I know if you use MCE there is an option to select your TV signal. It must be defined on Satellite.
  In addition, please read the manual for this device. Here you can find detailed information, descriptions and images about watching television.

  In addition, you can view this topic:

  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=6043&MessageID=20842#20842

  Please tell us if you have solved this problem.

  Good bye

• Printer tests very well and worked before; but now I can't seem to print

  Original title: problem with the wireless printer.

  I have a HP photo printer c309 all-in-one. When I run the printer tests in order to check if it is wireless, it passes all the tests. On my computer, the printer icon said he's ready. It has worked before. Now it does not work. Did not work for some time. I tried everything I know. If I plug in, it works. It not scan from windows and scan fax either and he used also. I don't know if something has changed regarding the settings on my computer or what. Very frustrating. I use verizon for my internet connection. Can you please help?

  Hello

  1. who is the operating system installed on your computer?

  2 have you made changes on the computer before this problem?

  3. you receive error messages when you try to print?

  4. What are the troubleshooting that you tried?

  I suggest you to follow the methods mentioned below and check.

  Method 1: Temporarily disable the security software and then try to print.
  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software
  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

   Method 2: Follow the steps in the article.

   Why can I not print?
  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-print

  
  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Method 3: Try to update the printer drivers and check if that helps.

  Check out the link for additional assistance mentioned in the update drivers below:
  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Thank you