Help RV180W Cisco

Similar Questions

• Help with Cisco PIX 506th

  I need help setting up a Cisco PIX 506th Version 6.3 (5)

  I use the PDM to configure the device, because I don't know enough of CLI. I want to just the simplest of configurations.

  Here is what is happening, I set up then I hang the Interface 1 to my laptop and use DHCP to get an ip address, but I can't get out to the internet like that. Thanks PDM tools, I can ping outside the IPS very well.

  6.3 (5) PIX version
  interface ethernet0 car
  Auto interface ethernet1
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate the encrypted password of DkreNA9TaOYv27T8
  c4EBnG8v5uKhu.PA encrypted passwd
  hostname EWMS-PIX-630
  domain ciscopix.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  object-group service udp test
  port-object eq isakmp
  inside_access_in ip access list allow a whole
  access-list inside_access_in allow a tcp
  access-list inside_access_in allow icmp a whole
  Allow Access-list inside_access_in esp a whole
  inside_access_in tcp allowed access list all eq www everything
  inside_outbound_nat0_acl list of permitted access interface ip inside 10.10.10.96 255.255.255.240
  inside_outbound_nat0_acl ip access list allow any 10.10.10.192 255.255.255.224
  pager lines 24
  timestamp of the record
  recording of debug trap
  host of logging inside the 10.10.10.13
  Outside 1500 MTU
  Within 1500 MTU
  IP outdoor 75.146.94.109 255.255.255.248
  IP address inside 10.10.10.250 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  location of PDM 10.10.10.1 255.255.255.255 inside
  location of PDM 10.10.10.13 255.255.255.255 inside
  location of PDM 10.10.10.253 255.255.255.255 inside
  location of PDM 75.146.94.105 255.255.255.255 inside
  location of PDM 75.146.94.106 255.255.255.255 inside
  location of PDM 10.10.10.96 255.255.255.240 outside
  location of PDM 10.10.10.192 255.255.255.224 outside
  PDM logging 100 information
  history of PDM activate
  ARP timeout 14400
  NAT (inside) 0-list of access inside_outbound_nat0_acl
  NAT (inside) 0 0.0.0.0 0.0.0.0 0 0
  inside_access_in access to the interface inside group
  Route outside 0.0.0.0 0.0.0.0 75.146.94.110 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-RADIUS (inside) host 10.10.10.1 server timeout 10
  AAA-server local LOCAL Protocol
  Enable http server
  http 10.10.10.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
  ISAKMP allows outside
  ISAKMP peer ip 206.196.18.227 No.-xauth No.-config-mode
  ISAKMP nat-traversal 20
  ISAKMP policy 20 authentication rsa - sig
  encryption of ISAKMP policy 20
  ISAKMP policy 20 md5 hash
  20 1 ISAKMP policy group
  ISAKMP duration strategy of life 20 86400
  part of pre authentication ISAKMP policy 40
  encryption of ISAKMP policy 40
  ISAKMP policy 40 md5 hash
  40 2 ISAKMP policy group
  ISAKMP duration strategy of life 40 86400
  ISAKMP policy 60 authentication rsa - sig
  encryption of ISAKMP policy 60
  ISAKMP policy 60 md5 hash
  60 2 ISAKMP policy group
  ISAKMP strategy life 60 86400
  Telnet 10.10.10.0 255.255.255.0 inside
  Telnet timeout 5
  SSH timeout 5
  Console timeout 0
  dhcpd address 10.10.10.2 - 10.10.10.5 inside
  dhcpd dns 68.87.72.130
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd allow inside
  btork encrypted Ww3clvi.ynWeGweE privilege 15 password username
  vpnclient Server 10.10.10.1
  vpnclient-mode client mode
  vpnclient GroupA vpngroup password *.
  vpnclient username btork password *.
  Terminal width 80
  Cryptochecksum:5ef06e69c17b6128e1778e988d1b9f5d
  : end
  [OK]

  any HEP would be appreciated.

  Brian

  Brian

  NAT is your problem, IE.

  NAT (inside) 0-list of access inside_outbound_nat0_acl
  NAT (inside) 0 0.0.0.0 0.0.0.0 0 0

  presumanly first NAT is fot your good VPN that acl looks a little funny, what exactly are you doing with that?

  The second NAT is the real problem but for outgoing internet access - the NAT statement, you said not NAT one of your addresses 10.10.10.x which is a problem as 10.x.x.x address is not routable on the Internet.

  You must change this setting IE. -

  (1) remove the second NAT statement IE. "no nat (inside) 0 0.0.0.0 0.0.0.0.

  (2) add a new statement of NAT - ' nat (inside) 1 0.0.0.0 0.0.0.0.

  (3) add a corresponding statement global - global (outside) 1 interface.

  This will be PAT all your 10.10.10.x to external IP addresses.

  Apologies, but these are some CLI commands that I don't use PDM.

  Jon

• With the help of Cisco ACS 5.2 (GANYMEDE +) with other than Cisco devices

  Hi all

  I was hoping that someone could help me with what might be a silly question. I'm trying to implement a solution whereby an operator can control all their nodes (other than Cisco) network via GANYMEDE + involved nodes are

  Juniper M10i running Junos 9.2, M120

  M320 running Junos 8.5 Juniper

  Extremes of BD8810 and BD8806 running 12.4.1.17 XOS

  3804 Alpine extreme Extremeware 7.8.3.5 running

  My question is, can I use Cisco ACS 5.2 (or 4.2) to authenticate using GANYMEDE + to these other than Cisco devices. Has anyone else done this or I have to use RADIUS? If someone has done this are problems of interoperability with Cisco CS and Junos or XOS extreme. Thank you

  / John

  John,

  We have a very large deployment of Juniper (T-series, series MX, etc.). We use Cisco ACS and GANYMEDE to manage these devices. The configuration of the ACS is fairly simple. You'll want to create users to connect and match them to the classes on your JUNOS routers. Here is an example:

  set system login user uid of engineering 2000
  Set system login user engineering genius-class class
  set the connection user uid to NOC 2001 System
  Set system login user AC AC-class class

  define the system connection Engineering-class idle-timeout 15
  define a connection system class engineering-class permissions all
  define the system connection AC-class idle-timeout 15
  define the connection class AC system class view permissions
  Set connection AC-class permissions see the system configuration

  We use two classes of genius and NOC. One is defined as a read / write and the second read-only. This is in turn then mapped in ACS (in our case version 4.2) by user or group (preferred). First, you change the configuration of the interface and add a Ganymede junos-exec service and do not enter the Protocol field. Then, you change the attributes of the user group. I've attached screenshots for both on this subject.

  Hope this helps.

  Derek

• Need help on Cisco UCS Certification

  Hi all

  I need your help.

  I intend to take the certification Cisco UCS. Please help me on this I am confused that you take as it is DCUCI or guide DCUCD please if it is DCUCI how to start and if DCUCD how to start.

  Currently working on vmware support and little UCS. I am after reading docs, and communities through videos from train signal UCS.

  Can some expert guide please, how further will be a great help

  Thanks in advance

  Vincent

  Vincent,

  Since how long did you ask? I want to mention that CCNA/P DC was relesed in November, before a review as DCUCI was a full certification and it is now part of the CCNP instead.

  CCNA has 2 reviews, DCICN & DCICT

  I couldn't find a link where it is specifically stated that you must follow a specific order, for example here:

  http://www.Cisco.com/Web/learning/certifications/specialist/DC/uc_support.html you can find specialized support requirements are:

  642-999 DCUCI (one of the basic tests I mentioned) & DCUCT 642-035 (one of the troubleshooting tests I mentioned as well)

  For CCNA, there is no choice, only 2 exams available, it does not matter for CCNP, but 4 you access CCNP, different combinations will give Add tax certifications.

  However, keeping in mind the names of examinations, which can give you an idea of what you want to learn first:

  DCUCI: implementation of Unified Computing DC

  DCUFI: implementation of DC Unified Fabric

  DCUFD: Data Center Unified Fabric Solutions Design

  DCUCD: Data Center Unified Computing Systems Design

  DCUFT: Troubleshooting Cisco Unified Fabric data center

  DCUCT: Troubleshooting Cisco Unified Computing data center

  I hope this helps clarify.

  -Kenny

• Newbie Help Needed: Cisco 1941 router site to site VPN traffic routing issue

  Hello

  Please I need help with a VPN site-to site, I installed a router Cisco 1941 and a VPN concentrator based on Linux (Sophos UTM).

  The VPN is established between them, but I can't say the cisco router to send and receive traffic through the tunnel.

  Please, what missing am me?

  A few exits:

  ISAKMP crypto to show her:

  isakmp crypto #show her

  IPv4 Crypto ISAKMP Security Association

  DST CBC conn-State id

  62.173.32.122 62.173.32.50 QM_IDLE 1045 ACTIVE

  IPv6 Crypto ISAKMP Security Association

  Crypto ipsec to show her:

  Interface: GigabitEthernet0/0

  Tag crypto map: QRIOSMAP, local addr 62.173.32.122

  protégé of the vrf: (none)

  local ident (addr, mask, prot, port): (192.168.20.0/255.255.255.0/0/0)

  Remote ident (addr, mask, prot, port): (192.168.2.0/255.255.255.0/0/0)

  current_peer 62.173.32.50 port 500

  LICENCE, flags is {origin_is_acl},

  #pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

  #pkts decaps: 52, #pkts decrypt: 52, #pkts check: 52

  compressed #pkts: 0, unzipped #pkts: 0

  #pkts uncompressed: 0, #pkts compr. has failed: 0

  #pkts not unpacked: 0, #pkts decompress failed: 0

  Errors #send 0, #recv 0 errors

  local crypto endpt. : 62.173.32.122, remote Start crypto. : 62.173.32.50

  Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0

  current outbound SPI: 0x4D7E4817 (1300121623)

  PFS (Y/N): Y, Diffie-Hellman group: group2

  SAS of the esp on arrival:

  SPI: 0xEACF9A (15388570)

  transform: esp-3des esp-md5-hmac.

  running parameters = {Tunnel}

  Conn ID: 2277, flow_id: VPN:277 on board, sibling_flags 80000046, crypto card: QRIOSMAP

  calendar of his: service life remaining (k/s) key: (4491222/1015)

  Size IV: 8 bytes

  support for replay detection: Y

  Status: ACTIVE

  Please see my config:

  crypto ISAKMP policy 1

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  encryption... isakmp key address 62.X.X... 50

  ISAKMP crypto keepalive 10 periodicals

  !

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac TS-QRIOS

  !

  QRIOSMAP 10 ipsec-isakmp crypto map

  peer 62.X.X set... 50

  transformation-TS-QRIOS game

  PFS group2 Set

  match address 100

  !

  !

  !

  !

  !

  interface GigabitEthernet0/0

  Description WAN CONNECTION

  62.X.X IP... 124 255.255.255.248 secondary

  62.X.X IP... 123 255.255.255.248 secondary

  62.X.X IP... 122 255.255.255.248

  NAT outside IP

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  card crypto QRIOSMAP

  !

  interface GigabitEthernet0/0.2

  !

  interface GigabitEthernet0/1

  LAN CONNECTION description $ES_LAN$

  address 192.168.20.1 255.255.255.0

  IP nat inside

  IP virtual-reassembly in

  automatic duplex

  automatic speed

  !

  IP nat pool mypool 62.X.X... ... Of 122 62.X.X 122 30 prefix length

  IP nat inside source list 1 pool mypool overload

  overload of IP nat inside source list 100 interface GigabitEthernet0/0

  !

  access-list 1 permit 192.168.20.0 0.0.0.255

  access-list 2 allow 10.2.0.0 0.0.0.255

  Note access-list 100 category QRIOSVPNTRAFFIC = 4

  Note access-list 100 IPSec rule

  access-list 100 permit ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 101 permit esp 62.X.X host... 50 62.X.X host... 122

  access list 101 permit udp host 62.X.X... 50 62.X.X... host isakmp EQ. 122

  access-list 101 permit ahp host 62.X.X... 50 62.X.X host... 122

  access-list 101 deny ip any any newspaper

  access-list 110 deny ip 192.168.20.0 0.0.0.255 192.168.2.0 0.0.0.255

  access-list 110 permit ip 192.168.20.0 0.0.0.255 any

  !

  !

  !

  !

  sheep allowed 10 route map

  corresponds to the IP 110

  The parts of the configuration you posted seem better than earlier versions of the config. The initial problem was that traffic was not in the VPN tunnel. That works now?

  Here are the things I see in your config

  I don't understand the relationship of these 2 static routes by default. It identifies completely the next hop and a mask the bytes of Middleweight of the next hop. Sort of, it seems that they might be the same. But if they were the same, I don't understand why they both make their appearance in the config. Can provide you details?

  IP route 0.0.0.0 0.0.0.0 62.X.X... 121

  IP route 0.0.0.0 0.0.0.0 62.172.32.121

  This static route implies that there is another network (10.2.0/24) connected through the LAN. But there is no other reference to it and especially not for this translation. So I wonder how it works?

  IP route 10.2.0.0 255.255.255.0 192.168.20.2

  In this pair of static routes, the second route is a specific subnet more and would be included in the first and routes for the next of the same break. So I wonder why they are there are. There is not necessarily a problem, but is perhaps something that could be cleaned up.

  IP route 172.17.0.0 255.255.0.0 Tunnel20

  IP route 172.17.2.0 255.255.255.0 Tunnel20

  And these 2 static routes are similar. The second is a more precise indication and would be included in the first. And it is referred to the same next hop. So why have the other?

  IP route 172.18.0.0 255.255.0.0 Tunnel20

  IP route 172.18.0.0 Tunnel20 255.255.255.252

  HTH

  Rick

• Support stand not provided my replacement WRT-ngn350 - need help with Cisco contact

  Hello!

  I'm starting to feel like Michael Douglas in the movie Falling Down and need help.

  History:
  Finally, I sent to my bad WRT-ngn350 router and when I got the replacement of all but the plastic leg support has been included. I want to have my router stand up to save desktop space, but now I have no foot.

  "OK, should not be difficult to get Linksys to send me the missing foot stand" was my thought. Now, I called the online RMA and also emailed them and I get a similar response as Michael Douglas took with a smile

  I hear that I can't get the part because it is not on the list the content of the product. As this is * my * problem. I want the part and do not care if it's on a list or not. It is the part on the router in the image. I even asked the representative of Linksys to Google a little bit WRT-ngn350 and there are foot stands on almost all of the images and it is certainly included in the box. I was told that I could go nowhere elsewhere to help with that. I really some doubt but fail to find a channel of Linksys, which may be able to help.

  

  If some representative of Linksys sees this please help me!

  Thanks, Niklas

  RMA XXXXX - lack of router support/foot

  (Mod Note: under the guidance of the compliance of the directive.) E-mail deleted conversation.)

  SOLVED!

  The representative of Linksys has managed to dig a booth for me to a warehouse. It is mentioned that it is a unique thing because some parts should be sent. Don't forget to remove the stand and send only: router, power and eventually cable NW.

  Thanks to Linksys representative.

• Help! CISCO WAP54G BUTTON

  I had my WAP54G for about six months... works very well, but I accidentally pressed the CISCO while wiping clean logo and now it does not work! I tried to reset and nothing not past, .the installation disk keep saying that a wireless access point is not found... and modem/router from my phir no longer sees the WAP54G connection.

  Now what?

  Manny

  I agree with Fredz... As reset you the router, now you must re - configure WAP from scratch. Try the link provided by Fredz and you will be able to configure your Access Point.

• Help on CISCO MARS20x 4.2.1

  My MARCH 4.2.1 just recognize netflow events, we need that they recognize the events and incidents, because in fact the only incidents created stipulates that ' rule of system: device Reporting CS-MARS inactive "how I can active, only configure us the netflow, what we need to do, or how long we have to wait, to recognize the CS-MARS and identify events.»

  Thank you very much, I expect you to your answers (excuse me for the English, but I am a beginner)

  Try these links:

  http://www.Cisco.com/en/us/products/ps6241/products_installation_and_configuration_guide_chapter09186a00804c4db4.html

  http://www.Cisco.com/en/us/products/ps6241/products_user_guide_chapter09186a00806056e6.html

• Help: Customer Cisco VPN & Split Tunnel but not Internet

  Hi Forum.

  We are faced with this problem: after having successfully open a VPN connection with the Cisco VPN Client to a router Cisco, the rest of the world are not properly available more.

  This is what has been verified / so far attempted to identify the problem on a Windows Vista computer:

  -Router: Split Tunneling is allowed according to sysop

  -On the VPN-Client: "allow Local Lan access" is checked

  -On the Client (statistics): only STI VPN-rout configured listed unter "guarantee routes." "Local Lan routes" is empty.

  -Calling 'http://www.google.com' in IE fails

  -Call ' 74.125.232.116' (IE IP) IE works / ping the IP works.

  -nslookup properly lists the current DNS server

  -nslookup www.google.com resolves correctly the name of intellectual property

  It seems that it is not that the connection with the rest of the Internet is deleted, but DNS resolution fails somehow, even though all signs point to the appropriate DNS server is in force and although the command line can resolve the name.

  does anyone have a tip how to debug this correctly?

  No worries Pat...

  Sent by Cisco Support technique iPhone App

  -Please evaluate solutions

• HELP of Cisco MOVI

  Dear,

  I have the Starter Pack of VCS Cisco implemented in my office with double network interface but I'm using only a single port network and his teeth to one ip address public static address and endpoint of c60 who is regesterd for vcs I have, and I can access my VCS on the internet via the public ip or domain in any case FULL name address I have a cisco MOVI installed in my house, I have followed cisco vcs starter pack deployment guide and I managed on the basis of rigester my movi of VCS, but when I try to call C60 endpoint I see the call is connected, but I get no audio and video.

  Please note that I am not an expert here, is there any other configuration as CLI commands that must be there please advise I only followed the Deployment Guide

  Commissioning doesn't have an internal external model like you would with TMS.

  You must therefore also a split DNS if you do not use both interfaces with commissioning.

  But when you deploy it appropriate also a model with the external ip address (with or without NAT, but always

  to connect to the external ip address) and the second interface on the network internal.

  I just use the public IP directly on the first interface and connect with all customers to the public ip address.

  (If your router supports to connect to IP using NAT outside that should also work).

  Please remember useful frequency responses and identify useful or correct answers.

• Help with logs on Cisco router

  First of all: if I'm in the wrong place, please let me know.

  Question: I'm digging orders Cisco, but the help of Cisco, Googe, Yahoo Sites and other types of resources can not give me the answer I wanted.

  Router: Cisco 7206VXR (NPE - G1) processor (revision C) with 983040K / 65536K bytes of memory.

  My question is simple and pleasant: I need to learn from the history of the Interface of one of our routers and not being is not in the domain of Cisco for a few years I can't find command. If I can find a command that draws a complete history that would be great.

  The commands I used:

  history

  history of show

  car1. Ash #sh interfaces se1/0/23:0 history
  ^
  Invalid entry % detected at ' ^' marker.

  car1. Ash #show interface se1/0/23:0 60 minutes story
  ^
  Invalid entry % detected at ' ^' marker.

  I need to find the command that gives newspapers the following type:

  00:00:46: % LINK-3-UPDOWN: Interface Port-Channel, 1 changed State to
  00:00:47: % LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed State to
  00:00:47: % LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed State to
  00:00:48: % LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, state change downstairs
  00:00:48: % LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed
  State down 2 * 1 Mar 18:46:11: % SYS-5-CONFIG_I: configured from console by vty2
  (10.34.195.36)
  18:47:02: % SYS-5-CONFIG_I: configured from console vty2 (10.34.195.36)
  * 18:48:50.483 Mar 1 UTC: % SYS-5-CONFIG_I: configured from console vty2 (10.34.195.36)

  What you are looking for is not available using interface show orders but would be available using the show log command. You want something that could look like this

  view Journal | include 1/0/23:0

  Note that this is the search through the buffer of logging on the router. The amount of memory allocated to the record buffer and the volume of messages generated will determine how far back you can go. If the router sends syslog messages to a syslog server (or another feature of management that archive messages) then you can search the logs it and to go further back. Also note that the logging buffer is cleared when the router reloads.

  HTH

  Rick

• Support of Cisco

  I needed to download the latest firmware for E3000 router wireless.  I started on Friday evening, went to the E3000 support page, then to the download section.  Here you will enter your version.  But to my page that I had, he would not allow me to enter anything.  I made this Saturday several times and Sunday several times but get the same results.  To see if the E3000 page was bad, I tried the WRT610 (my old router) download page and got the same thing not allowing me to enter anything.  I'm doing something wrong or is there a problem with the help of Cisco?  Can anyone give me any help would be appreciated.

  I went to another computer in the House and was able to download the latest firmware without any problems.  It tells me that I have some kind of problem with my main computer.

• Pilot of the Cisco VT camera

  Hi guys,.

  Need a help with Cisco VT camera Driver download? I searched in cisco website, it takes me no where, can you guys please help me with this.

  I had the camera with me, but no cd driver? What can I do with it?... Thank you

  See you soon,.

  Hari

  Hi Olivier,.

  Please click the link below:

  http://www.Cisco.com/Cisco/software/release.html?mdfid=278781226&softwareid=282074313&i=RM

  I hope this helps!

  Thank you

  Knockaert

• Need help to set up voice VLAN in SG300

  Hello

  I spent too much time on it now and need help. I'm trying to set up a voice switch VLAN on a SG300 - 28 p. I need to charge a phone Cisco 7965 connected to a port on SG300 - 28 p to use VLAN 100, and a workstation connected to the phone to use Cisco 7965 on VLAN 101 by SG300 - 28 p. In the common Cisco IOS switches, this task is configured as follows:

  interface gi25

  switchport mode access

  switchport access vlan 101

  switchport voice vlan 100

  Trying to achieve this scenario with a Cisco SG300 switch turns into a nightmare. You will have to deal with a Dynamic of VLAN voice Auto Voice VLAN mode. Then, you must have a configured trigger and activated Automatic Smartport . I tried to do this in CLI nothing helps. Cisco 7965 receives an IP address of the access VLAN on Gi15 interface, which is 101 VLAN. I need to receive an address IP of the VLAN 100.

  The current configuration under Gi15 interface is as follows:

  interface gigabitethernet15

  activate the storm control

  broadcast storm control level kbit/s 10

  Storm-control include multicast

  port security throw trap 60

  maximum port security by 10 points

  port security mode max-addresses

  spanning tree portfast

  LLDP-med disable

  switchport mode access

  switchport access vlan 101

  ! next order is internal

  macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100

  Now, I don't know how the macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100 command in the config, and I do not know how to remove it.

  When I try to enter the command macro auto smartport type ip_phone_desktop under Gi15 interface, I get the following error message:

  The $voice_vlan macro setting is not configurable by the user

  It seems that the auto attendant smartport macro ip_phone_desktop can not apply the setting $voice_vlan with a value of 100. In fact, I explicitly does not use this parameter to everything in the order of macro auto smartport type ip_phone_desktop ; However, the SG300 switch knows that the voice VLAN VLAN 100, and he's trying to use this VLAN ID as the value of the $voice_vlan parameter, the macro fails.
  

  I tried statically configure the voice VLAN on the switch SG300 using the command id of the vlan 100 voice , but I couldn't get the ip_phone_desktop macro to configure interface Gi15 correctly. Then, I removed the command id of the vlan 100 voice and obtained SG300 to learn his voice VLAN ID of UC560 connected to the SG300 through a trunk port based on the port configuration (connected to SG300) for the trunk of the next UC560:

  switchport trunk vlan 101 native

  switchport mode trunk

  switchport voice vlan 100

  Cisco-switch macro description

  This is the command switchport voice vlan 100 who announces to SG300 via CDP VLAN 100 is a voice VLAN. When I run the command show vlan local VoIP on the SG300, I get the following result:

  VLAN ID - VPT DSCP Source MAC address Interface

  1                    5          46       default           ----                    ---

  * 100 CDP e0:5f:b9:xx:yy:zz gi28

  Thus, it is clear that the SG300 receives information from UC560 via CDP in port Gi28 VLAN 100 is the voice VLAN. However, I can not always apply the ip_phone_desktop macro to SG300 Gi15 interface.

  Also, I tried to set up vState ofoithis vlan auto-déclenché as well as the commands in global configuration State vlan automatic voice activated mode. Or setting changes anything view voice VLAN announced at Cisco 7965 where Cisco 7965 continues to use VLAN101 (access the VLAN assigned to the interface Gi15).

  Hello telecastle,

  The Macro just get in the way most of the time. A default state on the switch a user will set the id of the vlan voice with orders

  (config) #voice vlan id 100

  * This will create the vlan 100

  VLAN, VoIP? * You can use to change your defaults for dscp and cos a long with all the other settings.

  State of vlan (config) enabled automatic #voice

  (config) #interface rank fa1-24

  (config-if-range) #switchport trunk vlan 101 native

  trunk (config-if-range) #switchport allowed vlan add 100

  * This function will define the vlan native on the trunk to 101 for the data port and vlan tagged will be 101 for the voice.

  CDP is enabled automatically and should learn the features of the phone and get on the phone to the vlan 101 on this port.

  CDP of the UC should automatically fill in the switch of the SG. You may need to upgrade the switch to the latest firmware however. Also make sure that the DHCP server for the voice if the CPU must be configured accordingly.

  Let me know if this helps.

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security

• ceiling of 75 Mbps Wireless-N

  I have a laptop dv6-3040us with Atheros AR9285 wireless LAN.  I can connect to my Linksys E1000 using Wireless N, but caps out at 75 Mbps speed. At first, I thought it was the router since my dv6 connected to a Netgear wndr3700 at 300 Mbps.

  An hour with the help of Cisco, however, could not solve the problem.  They suggested that upgraded the Atheros driver on the laptop.  After I did, I could only connected wireless G!  So I rolled back the driver.  I then tried a router D - Link DIR - 665 Xtreme, and speeds were also capped at 75 Mbps.  In both cases, I put the laptop in 4 feet of the router (5 bars of signal strength).

  My wireless desktop computer doesn't have the same problem.  It can connect to over 100 for the Linksys E1000 Mbps, even if it is further away.

  I was also careful to only use the WPA2 encryption based on some previous posts.  Does anyone else have this problem?  Is this a driver problem?  Why it limits on 2 N Wireless routers, but not the Netgear?  Thanks in advance.

  -Gene

  Atheros AR9285 work with N - 2.4 GHz only supports a single stream of data... If the max you out of this 150 Mbps Wireless card...

  Now to achieve 150 Mbps, you need to set the linksys E1000 or any router 'Automatic Mode '...

  Check the screenshot below... On how to get the Mode "Auto" is enabled on the Linksys E1000