Help with a Cisco Aironet 1242AG

Similar Questions

• Cisco aironet 1131AG AP radio interface down

  Hello
  I have a problem with my cisco aironet 1131ag AP radio interface.
  I configured the ssid, authentication and encryptation me have it (the ssid) associated with the radio interface, but the interface of dot11radio still in a State of remission to zero, and if a restart the interface this msg appears "% DOT11-4-NO_SSID: no SSID configured." Not started Dot11Radio0 ' what I need to do?
  Help, please

  Configuration:

  Building configuration...

  Current configuration: 1394 bytes
  !
  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  host ap name
  !
  Select the 5 secret $1$ Mf3YfBFQQS2.6MSWHQOeG0 $URAK
  !
  No aaa new-model
  domain IP Nida.local
  !
  !
  !
  dot11 ssid Nida
  VLAN 1
  open authentication
  authentication wpa key management
  Comments-mode
  WPA - psk ascii 7 01100F175804575D72
  admit-traffic
  !
  !
  diet pre-standard trading online
  !
  !
  username Cisco privilege 15 password 7 123A0C041104
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  IP 192.168.1.80 255.255.255.0
  no ip route cache
  !
  algorithms for encryption tkip encryption mode
  !
  encryption vlan 1 tkip encryption mode
  !
  SSID Nida
  !
  root of station-role
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0
  192.168.1.81 IP address 255.255.255.0
  no ip route cache
  automatic duplex
  automatic speed
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface BVI1
  customer_id FastEthernet0 dhcp IP address
  no ip route cache
  !
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  local connection
  !
  end

  You must create the dot11radio0.1 and fastethernet0.1 interface

  Must be something like this:

  version 12.4
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  encryption password service
  !
  host ap name
  !
  Select the 5 secret $1$ Mf3YfBFQQS2.6MSWHQOeG0 $URAK
  !
  No aaa new-model
  domain IP Nida.local
  !
  !
  !
  dot11 ssid Nida
  VLAN 1
  open authentication
  authentication wpa key management
  Comments-mode
  WPA - psk ascii 7 01100F175804575D72
  admit-traffic
  !
  !
  diet pre-standard trading online
  !
  !
  !
  Bridge IRB
  !
  !
  interface Dot11Radio0
  no ip route cache
  !
  algorithms for encryption tkip encryption mode
  !
  encryption vlan 1 tkip encryption mode
  !
  SSID Nida
  !
  root of station-role

  interface dot11radio0.1
  encapsulation dot1q 1 native
  Bridge-Group 1
  Bridge-group subscriber-loop-control 1
  Bridge-Group 1 block-unknown-source
  No source of bridge-Group 1-learning
  unicast bridge-Group 1-floods
  Bridge-Group 1 covering-disabled people
  !
  interface FastEthernet0
  no ip route cache
  automatic duplex
  automatic speed
   
  interface Fastethernet0.1
  encapsulation dot1q 1 native
  192.168.1.81 IP address 255.255.255.0
  Bridge-Group 1
  No source of bridge-Group 1-learning
  Bridge-Group 1 covering-disabled people
  !
  interface BVI1
  customer_id FastEthernet0 dhcp IP address
  no ip route cache
  !
  IP http server
  no ip http secure server
  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
  1 channel ip bridge
  !
  !
  !
  Line con 0
  line vty 0 4
  local connection
  !
  end

  PS has also removed the ip address dot11 interface slot and I'm not sure why the role of station is root?

• Point of access Cisco Aironet 1200 series help

  We have 4 Cisco Aironet 1200 Access Points and they are all set to authenticate with our RADIUS server. However, authentication is hooked and can't understand why. Does anyone have any knowledge/experience with Cisco Aironet 1200 Access Points configuration?

  OK, I do not work with the GUI so although the memory is a little hazy but from the APs home page look on the left hand side and there is an option for something like "Software Setup" or something to that effect. You should be able to find the IOS version of here. This requires that you are indeed runnig IOS code. How old are these APs? If more than a few years ago (and perhaps even more recent) that they could very well be running VxWorks and then we are in a different ball game. If you see what I have described above and the homepage for the AP is often white with a bit of greenish-blue, bluish-green color then IOS, if it is more colorful, yellow stuff and VxWOrks.

  I hope this helps. Let me know if you need anything that anyone else. I will try to answer as soon as POSSIBLE.

• Help with M6348 connecting to a Cisco network

  Hello

  Can someone help me with best practices by putting R710 via a M6348 stacked with a cisco network.

  Our configuration is the following

  M1000e

  2 x 1 GB pass-through fabric a

  2 x M6348 wired in a pile in the B fabric

  6 x popular R710 with four NIC ports in the fabric B (3 are general purpose servers, 3 are Hyper-V servers in a cluster)

  Cisco network

  For most of the Cisco 3560 switches

  20 VLAN (1 per building) configured, mainly for the isolation of traffic (VLAN 300-320)

  What (I think) that we want to

  The M6348 connect to the core network in a SHIFT (4 x 1 GB ports. Can it be divided 2 ports each of the stacked M6348?)

  Have a mapping of right for 1-3 to VLAN 301 R710

  Configure R710 4-6 for access to all VLANS for the Hyper-V hosts can be placed on the VLAN correct

  Use the fabric for the connection to the San

  Network management is carried out by a third party (we are unable to change this) and they claim that they are unable to connect Cisco/Dell!

  We are server guys, guys network no, so something stupid (especially for Cisco to give to our management company) would be appreciated.

  We tried to configure the switches in Simple mode, using a Dell deployment guide, but all we seem to get is the default VLAN to all ports on the switch 1 battery, but no other VLAN and no active port 2 in the stack.

  I've probably missed lost info on and were not very clear, so if more info is needed, please get back to me.

  Thanks in advance for the help

  Rich

  Thanks for the information updated, actually, this confirms that the problem is with the connection to the Cisco switch. Is that what we tried a general link, instead of trunk?

  mode console # switchport general

  Console # switchport General allowed vlan add 300-320 tag

  Console # pvid General switchport 301

  Console # end

  Are we sure that the VLAN 301 IP address is 10.49.56.0? This doesn't seem fair.

  When we try to pings on the trunk/General connection to the Cisco switch, make sure you that the servers have the default gateway defined on the VLAN IP address they are in access mode. Thus, when in the access mode VLAN 301 the gateway server would need to be 10.49.56.0. I would like to verify that the IP address, however.

• Beginner needs help with Aironet 1131 G Wireless Access Point

  I have a new Cisco Aironet 1131 G wireless access point.  It takes an IP address and I can ping this address.  However, I can't access it via the graphical user interface based on the web or the CLI.  I preformed reset.  Any suggestions would be greatly appreciated.

  Thank you.

  Hello

  I can't access that means? you are not able to go to the CONFIG T of the CLI prompt? and if you are in the same subnet as the AP, are you not able to open to the top of the GUI? If you are not able to then, with the command 'show version' on the AP CLI and see if your image is "RCVKW8". If so you will need to convert the same IOS using the method below.

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap22-trouble.html#wp1038660

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• Need help with configuration on cisco vpn client settings 1941

  Hey all,.

  I just bought a new router 1941 SRI and need help with the configuration of the parameters of the VPN client. Orders aspect a little different here, as I'm used to the configuration of ASA and PIX for vpn, routers not...

  If anyone can help with orders?

  I need the installation:

  user names, authentication group etc.

  Thank you!

  Take a peek inside has the below examples of config - everything you need: -.

  http://www.Cisco.com/en/us/products/ps5854/prod_configuration_examples_list.html

  HTH >

  Andrew.

• help with 2 concurrent internal users trying to VPN (Cisco s/w) at extern

  Hi all

  We are a small office running Small Business Server 2003 - which means that we miss the ISA 2004 firewall.

  An external company provided us with the Cisco VPN (ver403a) software to access their site web network / secure.

  One user could connect to the network of the company for some time. It was working fine until two users tried to connect at the same time - using the same VPN user ID. We have learned by the company that it should work, but it just isn't so we asked a second VPN user ID to test with.

  Now what happens is that the user has to connect with success and user B can connect successfully at the same time however even if user B is connected, and you see even an IP assigned to the VPN adapter, the user can not ping the company website and then of course can not access it. Very strange indeed!

  I went back to the company and told her about our dilemma and we were told that there is nothing at their end, but a problem of Routing/NAT at our end. So here, I'm now looking for help I hope that some experts from Cisco. :-)

  Appropriate, the ports were opened in ISA and once again the two users will connect to the VPN very well, it's just that the second user can? t go further.

  It was suggested to me that is maybe not a routing problem, but that Cisco VPN server/box the company rejects the second connection because it comes from the same IP address - that would be the IP address of our ISA Server external network card.

  If anyone has any suggestions on how to solve this problem, I would be so grateful!

  Thank you very much.

  Tammy

  VPN configuration multiple tunnels for the same device (same public IP address) is not possible because it is not possible to have several (SA) IPsec Security Association for the same position. However, it is possible to configure multiple VPN tunnels to multiple devices. In your case, if your client PC using public IP addresses, they both can simultaneously connect to the remote vpn server. However if you are using a single public IP address so it is not possible to have mutiple vpn connections. If you have only a single ip address of your ISP then it would have to do PAT and you will be not able to have the two vpn clients to connect to even

  time.

• Support stand not provided my replacement WRT-ngn350 - need help with Cisco contact

  Hello!

  I'm starting to feel like Michael Douglas in the movie Falling Down and need help.

  History:
  Finally, I sent to my bad WRT-ngn350 router and when I got the replacement of all but the plastic leg support has been included. I want to have my router stand up to save desktop space, but now I have no foot.

  "OK, should not be difficult to get Linksys to send me the missing foot stand" was my thought. Now, I called the online RMA and also emailed them and I get a similar response as Michael Douglas took with a smile

  I hear that I can't get the part because it is not on the list the content of the product. As this is * my * problem. I want the part and do not care if it's on a list or not. It is the part on the router in the image. I even asked the representative of Linksys to Google a little bit WRT-ngn350 and there are foot stands on almost all of the images and it is certainly included in the box. I was told that I could go nowhere elsewhere to help with that. I really some doubt but fail to find a channel of Linksys, which may be able to help.

  

  If some representative of Linksys sees this please help me!

  Thanks, Niklas

  RMA XXXXX - lack of router support/foot

  (Mod Note: under the guidance of the compliance of the directive.) E-mail deleted conversation.)

  SOLVED!

  The representative of Linksys has managed to dig a booth for me to a warehouse. It is mentioned that it is a unique thing because some parts should be sent. Don't forget to remove the stand and send only: router, power and eventually cable NW.

  Thanks to Linksys representative.

• Cisco Aironet SAP1602E - changing open to WPA - PSK access remote (RAP and map)

  I currently have a deployment of Cisco Aironet SAP1602E Wireless point to point bridge (bridge using RAP and card, root wireless and Non-Root Bridge) to expand a layer 2 VLAN from one building to the other. It currently operates uisng open authentication and encryption - and is administered remotely via the bridge of root, to get wireless (manage) the bridge Non-Root - RAP wireless remote.

  Try to configure the PSK WPA2-PSK remotely via the GUI or CLI - first setup - I informed a similar error to her below indicating that:

  Error: Key-management WPA is requried for WPA-PSK

  Read around, it seems, there is a configuration-control problem, and that I need to specify the mode as WPA2-PSK first, before then being able to specify the PSK there instead of using. However, as soon as this mode is specified on RAP, my remote administration is broken - as probably the RAP try to use WPA2-PSK to look for a PSK, which has not yet been configured. Am I missing something obvious here, or is the order of operations of CLI (1] convert to WPA - PSK; (2] shared secret to apply PSK) as a migration from open to WPA2-PSK cannot be configured remotely (short of preparation of a startup-config; TFTPing presents more; and issuance of a 'reload' remote control)? Can someone please enlighten me as to what the logic is here - no doubt I should be able to specify a PSK first (fo without worrying if I use WPA, WPA2 or other), and then be able to specify that I want as the layer of encryption (WPA) to make use of this pre-parameter PSK? If it was a router, you don't can me to add something to the authentication key chain OSPF; before clarifying its use - why so different Aironet Wireless IOS?

  You're right, and because you will have to enter several lines of configuration to switch to WPA2-PSK with AES didn't really matter; the AP would reset the radio anyway because you make changes related to the radio interface. It would be very useful that if Cisco router/switch IOS 'macro' feature available AP thus in changes like this, unfortunately this is not the case.

  Start with the nonroot AP and make sure that the following lines are added to your configuration. If you add by the console, the order must be like that, do it by downloading a new configuration of booting with tftp, that it does not matter.

  interface Dot11Radio0
  encryption ciphers aes - ccm mode

  SSID dot11 TEST
  authentication wpa key management
  WPA - psk ascii 0

  Please rate helpful messages... :-)

• Cisco Aironet 1830 disable broadcasting of the SSID

  I recently bought a Cisco Aironet 1830 with the mobility Express version. installed 8.2.100.0. This unit is my controller and my only AP. I configured the device, but I can't seem to find a setting in the GUI or the CLI of the controller or AP disable broadcasting of the SSID. Can someone help with this?

  Thank you

  The CLI is available, the following command:

  config ssid broadcast disable wlan where wlan id is the number of your wlan. If in doubt, do a show wlan summary which should give you this info, I hope.

  Ric

• Several points of access Cisco Aironet 1131AG and same SSID?

  We have several Cisco Aironet 1131AG, all wired devices on a switch (2560) Cisco L2 which is connected to the L3 switch (3550). We have assigned a VLAN for access point to the L3 switch which acts as a vtp Server (L2 switch is vtp client). All the ap will have a static ip address and all will have the same SSID and no security, and they will use several channels (e.g. 1,6,11).  They will work in 3 floors for a roaming wireless client. We not using any wireless controller.

  So my question is this: how to configure the same APs-all with a different ip address, can we use L3 switch to create the dhcp server to access points VLAN (pool for guests) and the rest of the static ip address for the ap? One of the ap can be WDS and on the same radius server local time with users without Cisco Secure ACS or similar controller or I did not understand this very well :-). I followed the guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_2_JA/configuration/guide/s32roamg.html for WDS where Abu Cisco ACS part is a problem, so I can use the same ap as a Local authenticator as a guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/configuration/guide/s34local.html#wp1035723.

  Thank you very much...

  Well, just so you know, WDS, and local RADIUS authentication is necessary only if you use authentication on your wireless connection.  You say that you do not plan to use security, so it's not necessary.  However, I highly recommend at least using a simple WPA2-PSK to lock your connection, otherwise you might end up giving free Internet access at best and at worst you could give access to the computers and corporate servers.  If you want to reuse a 802. 1 x or WPA authentication method, then Yes, you can use an AP as RADIUS and to improve WDS Server authenticated to roaming, but this is much more limited than the use of a Cisco ACS.

  As for your other questions, Yes, your APs can all be configured the same except for at least three settings: IP address, hostname, and channel.  Configure your static IP addresses on the interface of the PA BVI1.  Do not place it on the Radio or Ethernet interfaces, because if one of these interfaces goes down, you lose the ability to configure the AP, so it's best to use the BVI1 interface.

  And Yes, configure a DHCP scope for your customers on your L3 switch is good design, or you can also use your DHCP server on a different subnet by using the command of support-ip address on the interface of L3.  I hope this helps!  Let me know if you need help to set all this up.

  Merry Christmas!

  Jeff

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• Helps with the rv180w and the Shrew soft vpn

  Hi, I'm trying to establish a vpn connection by using soft shrew for the cisco rv180w router.

  I watch and read everything I could find, but the connection drops during the opening of the tunnel.

  There were a few tuttorial here in the forum, but the links are down.

  I want Edifier is to establish communication and to be able to access my domain on the network.

  Any help with the settings would be greatly apeciated. I am new to vpn.

  Thanks in advance.

  Federico,

  Try to access the following link. It has good instructions for a similar model. The main difference is that the SA500 has double-WAN and the RV180W does not work.

  https://supportforums.Cisco.com/docs/doc-9378#comment-7216

  Here's another tutorial for the RVS4000 that can help:

  https://supportforums.Cisco.com/docs/doc-18443

  Check out the last post in the following thread, which received instructions for the RV220W (should be exactly the same as RV180W)

  https://supportforums.Cisco.com/message/4165652#4165652

  -Marty

• Cisco Aironet 1131AG and measure access points to the power of the wireless signal?

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  We have about forty points of access Cisco Aironet 1131AG spread over four floors and they all have a static IP (BVI1) on the same SSID, customers will be on its own virtual local area network (dhcp on 3750 switch) and they use several channels (1,6,11).  Cisco Wireless Control System is pending. This wireless network should support roaming for customers (there will be Wi - Fi tags of multiple AeroScout and wireless laptops). To measure the strength of the wireless signal and wireless coverage on each floor. My questions are:

  1. How to measure the strength of the wireless signal: we must meet at least three APs available with signal excellent (I guess for the WCS needs that will determine the position of the client in the building)? We thought to use NetStumbler and a few laptops with wifi and measure as many points as we can as simpler thing. Or should we use something like Cisco Aironet Client adapters for our mobile phone and then use Cisco Aironet Client Utility (is it worth buying for our analysis and measurement)? Any other idea?
  2. What signal level should we consider for a good wireless (dBm)?
  3. That we should propose for authentication, authorization and management accounting? What happens to the roaming wireless? I did not quiteunderstand WCS, WDS and WLC-that should be used for above tasks?

  Thanks in advance.

  "Use the command on the AP" sh dot11 associations "will give you the clients associated with success.  If you add the MAC address of the client at the end of the command, you will get detailed information.  Look under "Signal Strength" and "Signal to noise".  Under the strength of the Signal, you want a value of-75 dBm or lower (lower values the better).  -76 dBm and is bad.  Under Signal-noise, you want a value of 25 dBm or more (values higher the better).

  To measure the strength of the signal, I use Airmagnet, but you can use Netstumbler or Cisco Wireless Site Survey.

• Cisco Aironet 1140 Standalone AP

  Greetings. For some time I'm looking for bargains from a class wireless access point. I narrowed down it to the stand-alone Cisco Aironet 1140 (no controller). I'm no stranger to Cisco products. I worked with the routers, switches and firewalls Pix / ASA. However, I did not have the opportunity to work with their wireless access point I hope that someone here who has experience using these AP (more precisely the autonomous 1140), can provide information on the reliability and safety of these devices. Some of the features that I would like to have as Mgmt. Radio and Rogue AP Detection I see are only available on the controller base units. Do not have these features on the autonomous unit reduced its reliability and safety? It's for a small business and the budget does not drop to a controller at this time. Thank you!

  The 1140's are a good choice for standalone 802.11n. Regarding reliability and safety, it would be identical to a lightweight AP. you can use different types of encryption as well as using 802.1 x. You will not not reliable detection functions or management of radio since these are autonomous.

  Thank you

  Scott Fella

  Sent from my iPhone