Help with vista crashing, please.

Similar Questions

• Help with Vista SP2

  The system is;

  Manufacturer: ASUSTek Computer Inc..

  Model: ASUS G50VT Notebook series

  System type: 64-bit operating system

  I can't get the Vista SP2 to settle... I even tried to do it manually.

  Help me please...

  A Google search for 10 seconds found...

  
  Use the hidden, reserved for the purpose of recovery, partition in the hard disk to restore your computer to factory settings.  Backup your data first.

  Restart your computer.  Press the F9 key immediately when the logo ASUS appears.  This will start the recovery procedure, including the installation of all the drivers and utilities.  Follow the instructions.  Your computer will be restored to factory settings.
  
  Source: (BestBuy) http://vip.asus.com/forum/view.aspx?board_id=3&model=G50Vt & id = 20100112105613468 & page = 1 & SLanguage = en - us

  If you need additional help with the new installation, contact ASUS support or start a new thread in this forum: http://social.answers.microsoft.com/Forums/en-US/vistarepair/threads

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• 1IZ satellite A200 with Vista crashes every day without no reason

  Hello guys,.

  I have a Satellite A200 with Vista Home Premium installed. In the past months, the BONE is suspended every day, I was not able to detect the reason. nothing is having replied to the questionnaire, not even Ctrl-Alt-Delete, the only solution is to stop from the power switch.
  I do not found something wrong in the system log, so I do not know what to do. Toshiba PC diagnostic shows everithing OK.

  What can I do? Perhaps a cooling problem? A guide for cleaning?

  Thank you.

  Hello

  So to be honest, it's hard to say what are the really causes your system to hang. Possible reasons:

  HIV 1-infected
  2 problem of file system Os including drivers, programms...
  3 had to be clean
  hardware problem 4

  I recommend:

  1 search for viruses
  2 reinstall the drivers (especially as a vga and chipset drivers). Check installed programs
  3 use compressed air jet to blow off the dust from the cooling module.

  If this does not help, do a fresh install of the operating system. Then we will see what to do

  Welcome them

• Help with shared folders, please

  Running Win Vista/64, almost all folders and files under Documents are also shared, with the "two guys" icon superimposed on the icons of folders and files.  Obviously because they are 'shared', these files and folders are very difficult to remove or move, take resources from the computer for a minute or more per operation.  I tried 'break' them and even to remove the names of all listed users for the file or folder, but can't get them to the State not shared.  Can someone please?  Either way, all folders and files becomes shared when I opened Windows Movie Maker once to see what it could be used for.  Just open the program seems to be what has marked all these files and folders as 'shared '.

  Finally, I realized that for me.  With Windows Explorer, click a shared folder in the left pane so that all shared files are visible on the right.  Select (highlight) all the files, then right click on one and when the window opens, click on: "share...." ».  Then click on "Stop sharing" and to sit back and wait a few minutes.  I have no idea why, but it takes for-ev-er to run the "stop sharing".  Once the files 'no sharing', then you right click on the folder and do the same thing with her.  Be prepared to spend a lot of time to exercise, according to the number of files shared.

  Always start at the lowest level (deeper?) and backward from there.  You can not cancel sharing a folder until all the files inside are shared.

  Yet once, which required all this simply opened the program Windows Movie Maker comes with Vista.  Of course, it goes through your hard drive and share all the files that could never have no interaction with the Movie Maker program... same word .doc and .pdf files.

• Need help with the composer please?

  I am very new to view and work my way through the implementation in our society. I get two different messages when the composer fails.

  "Could not perform the operation active directory. COM 2147016654 "error code

  "the partial distinguished name of the ad container specified is not valid.

  I would appreciate help with this. Thank you very much in advance!

  -Brandon

  Please consider awarding points by scoring responses as 'correct' or 'useful '.

• Help with required fields please

  I tried to get help with a required field and of forum aid said he's got to work for me but I can't and I have not been able to get answers more of him to help me more.

  I try to have a radio box when YES is selected to demand another field to fill.  The script I got is:

  getField("Location").required = (getField("Group1").value == 'Yes');

  Location is the area I need to be filled if the Group 1 is Yes.  The previous programme of assistance forum said I had to have this script in the two fields in Group 1 and when I do that, nothing else happens.

  What I am doing wrong?

  Please, I need to fix this immediately and I'll use this java script on many other forms that I have so I need to get there soon.

  Thank you in advance.

  This works.  It's perfect.  Thank you very much. You're my hero!

• Help with button code please?

  I am a novice and have completed my first animated film. I need help with action script.

  The film is currently in a loop and I created and invisible button the size of the frame with the intention that a user can click on the picture of the movie to stop it and the second click continue the film from where it stopped.

  I used AS event handler method to stop the sequence. I tested it and it works. But I can't understand the appropriate code to restart the movie.

  Two questions;

  1. I go to the task the right way? (should I use two buttons, a stop, a tenure)?

  2. If my approach is possible, can someone give me the right to re - start the movie and put me out of my misery please?

  You can use the following after having changed 'yourbutton' and 'yourmovieclip' to use appropriate instance names:

  {yourbutton.onRelease = function ()}

  {if(!this.) Toggle)}

  yourmovieclip. Stop();

  } else {}

  yourmovieclip. Play();

  }

  This.Toggle =! This.Toggle;

  }

• Help with multitasking it please?

  Since I got my phone (Moto G 8 GB), multitasking has been terrible. I love the phone, but it's his left out major. Switching between the 2 applications at the same time generally involves having to reload the entire application, even some of the lighter applications such as contacts. I looked in the settings and everything is OK, as the apos as the default background. Also, I don't seem to have any heavy applications running in the background. Facebook is the heaviest app I have on my phone. I wonder if there is anything I can do to remedy to this or if anyone else has this problem?

  When you switch between applications, they restart because the system runs on the RAM. You see the message to reboot on some of these processes because the system killed these processes in order to keep others running and to free some RAM when its need is why you always have a bit of free RAM.

  Even the Air iPad with 1 GB of RAM, even that bike G, has problems, keeping applications running in the background. I'm afraid that this problem is quite normal if you have applications that run in the background taking up RAM. The system kills just the process relatively little important, as Google play music and display of WiFi, to keep others running and have at least a little memory available when it is needed.

  So you're an Android user average above that you have several applications that won't install average consumers, so I recommend going with a phone in the future who has at least 2 GB of RAM.

  P.S. I read in places that Motorola is aggressive with background applications to help with the battery, so maybe that is why the system cannot even keep apps simple people in memory, even if you have still a few available RAM.

• Help with vista configuration update 3 of 3 Please do notturn your machine off

  Please help my pc went into the update and was stuck in this now for about 8 housr. Have tried twice to restart in safe mode, but it still shows the same.

  I have no idea what to do and I'm afraid I'm not very technical so if anyone has any ideas please run by me in a very simple way.

  Thank you

  Give this one a whirl:- http://support.microsoft.com/kb/949358>

• Need help with windows update please!

  Tried for months now to get windows update to work properly. I still see a message pop up in my lower toolbar, that says: windows cannot verify the updates, with a red x. I'll try to update manually and it shows 0% all the time. When I go and check to see if there have been updated, it will show a little from time to time, who have downloaded successfully, but believe that is made during a unrolled task he is set to make only 1 or two from time to time will show. I don't know what else to do. It's Windows Vista. Help, please... My Windows defender seems to fine day. Help, please... Thank you...

  Hello

  I guess that part of the question could be a driver which is really old or similar should not be loaded.

  This exit Windows updates on (after you have access) and stop the updates of the driver to load.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ---------------------------------------------------

  You can use the solutions in this KB - 3 methods and I listed a little help for them below

  The update is not installed successfully, you receive a message, and the computer restarts when you try to
  install an update in Windows Vista
  http://support.Microsoft.com/kb/949358

  Method 1: Start Windows Vista with the Windows installation media and use the repair feature

  How to do a startup repair in Vista
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  You can also do a safe mode startup repair to access the Recovery Options If you have them available
  or use the DVD as described above.

  This tells you how to access the System Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Method 2: Start the system in safe mode and then use the system restore feature

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can also do a restore of the system of starting with a Vista disk.

  Method 3: Rename the Pending.xml file, and then change the registry (this method is part of the advanced troubleshooting)

  See article below for that.

  You can use this method on the updates that have this problem.
  http://support.Microsoft.com/kb/949358

  Hide the update (click right - HIDE in the updates of Windows) and go to the Microsoft Download Center to download
  and install it.

  Microsoft Download Center
  http://www.Microsoft.com/downloads/en/default.aspx

  ------------------------------------------------------

  Once you are in Windows I was running once again reset here as a precaution.

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Hope this helps sort it out for you.
  Rob - bicycle - Mark Twain said it is good.

• Problems with Vista Crash

  Hi, I bought a Dell XPS 1640 recently but after I installed Win7 OEM, a lot of blue screen

  that's happened. So I spent again in Vista 64-bit.

  But now I still have two problems

  (1) I can't install my official driver of Dell wireless 5530 HSPA network card minicards

  because whenever the installation process would automatically be terminted i even did nothing and

  close all anti-virus software or firewall.

  (2) now I got another question. Every time when I want to disconnect my external hard drive from Seagate,

  a blue screen happen as below

  Signature of the problem:
  Problem event name: BlueScreen
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 2057

  More information about the problem:
  BCCode: a
  BCP1: 0000000000000010
  BCP2: 000000000000000C
  BCP3: 0000000000000000
  BCP4: FFFFF80001C86489
  OS version: 6_0_6002
  Service Pack: 2_0
  Product: 768_1

  Files helping to describe the problem:
  C:\Windows\Minidump\Mini011910-01.dmp
  C:\Users\huang\AppData\Local\Temp\WER-49218-0.SysData.XML
  C:\Users\huang\AppData\Local\Temp\WER89A8.tmp.version.txt

  Read our privacy statement:

  http://go.Microsoft.com/fwlink/?LinkId=50163&clcid=0x0409

  Can anyone give me some suggestions? It is so annoying that I have nothing of win7 but still

  could not feel safe in Vista...

  Hello

  Added new hardware, updated drivers to date (don't forget to check in Control Panel - Windows Updates - pilot
  updates), or add key software lately? Pilots and security/antivirus/antispyware products are also likely
  suspects. Next message is my generic driver updated methods to use when you get to this section of the
  troubleshooter.

  BCCode: a 0x0000000A

  Cause

  This bug check is issued if the memory paged (or invalid) is accessible when the IRQL is too high.

  The error that usually generates this bug check occurs after the installation of the faulty device driver or service system, BIOS.

  If you encounter a bug 0xA control during the upgrade to a later version of Windows, this error can be caused by a device driver, system service, an anti-virus or a backup tool that is not compatible with the new version.

  Solve the problem

  If a kernel debugger is available, get a stack trace.

  To resolve an error caused by the faulty device driver or service system, BIOS

  1. Restart your computer.
  2. Press F8 to character-based menu that displays the choice of operating system.
  3. In the Windows Advanced Options menu, select last known good Configuration . This option is most effective when a pilot or a service is added at a time.

  To resolve an error caused by an incompatible device driver, system service, virus scanner, or backup tool

  1. Check the system log in Event Viewer for error messages that may identify the device or driver that caused the error.
  2. Try disabling the cache in memory of the BIOS.
  3. Run the diagnostics of equipment provided by the manufacturer of the system, in particular the scanner memory. For more information about these procedures, see the manual of your computer.
  4. Make sure that the latest Service Pack is installed.
  5. If your system has cards (SCSI) small computer system interface, contact the card manufacturer for updated Windows drivers. Try to disable sync negotiation in the SCSI BIOS, check the wiring and the SCSI ID of each device and confirming the proper termination.
  6. For devices (IDE) peripheral electronic integrated, set the built-in as only primary IDE port. Also, check each IDE device to the right setting master/slave/stand alone. Try to remove all IDE devices except for the hard drives.

  If the message appears during installation of Windows, make sure that the computer and installed devices are listed in the list of the products tested Microsoft Windows market.

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  It is my generic troubleshooting tool and can probably give more specific help when you give the ICC codes.

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Need help with Vista updates

  Hi my computer tried to install Windows vista service pack 2 (KB948465) and update for Windows Vista (KB967723) security. And he said: updates could not be installed error found: 800 b Code 0100. Can someone please help me get this situated

  Hi Corey90,

  Welcome to the Microsoft Vista answers Forum!

  I have some steps that may help you.

  Step 1

  1 run (Checksur.exe) system update readiness tool

  2 download and run (Checksur.exe) system update readiness tool. After downloading this tool, it runs a scan of a time for inconsistencies that might prevent future maintenance operations.

  For more information about how to download and run the Checksur.exe tool, click on the number below to view the article in the Microsoft Knowledge Base:

  ·         Run the preparation tool the link for Windows Vista 64 bit http://www.microsoft.com/downloads/details.aspx?FamilyID=b950e3b1-3267-41c2-8f10-1fe9a4bfa44d system

  ·         Run the preparation tool the link for Windows Vista 32 bit http://www.microsoft.com/downloads/details.aspx?FamilyId=b4d90b06-c27d-4483-bc1f-04d43fa7b293&displaylang=en system

  Error message when you try to use Microsoft Update or Windows Update Web sites to install updates: "0x800B0100' http://support.microsoft.com/kb/956702

  Step 2

  You will need to maybe reset the Windows Update components, download the Microsoft fix - it from the link and run the wizard that automatically resets the windows update components, if it does not, I recommend that reset you manually update windows components from the link: http://support.microsoft.com/kb/971058

  Step 3

  Scan the file system [SFC] checker on the computer that replaces the corrupt files on the computer system, follow the steps below.

  1. start and type cmd in the box start the search.

  2 - Click on cmd in the list programs and then click Run as administrator.

  If you are prompted for an administrator password or a confirmation, type your password or click on continue

  3. at the command calls, the following line and press ENTER: sfc/scannow

  When the analysis is complete, test to see if the problem you are experiencing is resolved.

  Additional information: http://support.microsoft.com/kb/936212

  Diana
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Help with Vista Pack 2 64 bit OS

  I have Vista Pack 2-64 bit OS on my computer and want to download Cricut Design studio, which requires Vista 32 bit only... is there a way for me to change to 64-bit to 32-bit... How can .and I do this?  What else will be affected?  Help

  32-bit and 64-bit are two completely different operating systems.

  You will need to purchase a full version of Vista 32 bit operating system you want and do a clean install from a 64-bit operating system for a 32 bit one.

  How to clean install Vista:

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  See you soon.

  Mick Murphy - Microsoft partner

• Need help with Vista not recognizing the .sys file

  Please help me!  I am trying to load a driver USB 2wire on Vista and it does not recognize the .sys file.  Can I convert this easily to .exe, or y at - it another way to achieve this... I am a novice at best here.  Thank you!

  Can you check it out here:

  http://support.2Wire.com/?page=view&article=545

  just to see that you found the driver for the right adapter. It turns out that there are two.

  I won't be able to respond for a while.

• Help with drivers? Please, I beg you!

  Hello

  I recently had to buy a new hard drive for my Advent 5431. I had a Toshiba MK1652GSX 160 GB and have now bought a Samsung Spinpoint 250 GB.

  Having bought my computer PC World/The Tech guys it did not come with an installation CD, so I bought one on eBay.

  Anyhoo, I was wondering if after replacing the hard drive and the installation of vista, I said I have to install the drivers.

  Really, I have no idea about the drivers and I was wondering
  -How are?
  -where can I get a?
  and basically I was wondering what they are, etc. and if it would be easy to install and where to go.

  Any help is appreciated,
  Concerning
  Julie

  Hello

  Search for drivers updated, BIOS, software control (if any) and others that you can find in the
  Sites of the manufacturer the manufacturer of the device or system.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN -.
  REBOOT after each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check manually
  by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, that leaves about Windows updates but it will not install the drivers that will be generally
  older and cause problems. If updates offers a new driver and then HIDE it (right click on it) and
  Then, get new ones manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  Hope these helps.

  Rob - bicycle - Mark Twain said it is good.