Helps connect Router WRT160N and WEP key

Similar Questions

• Change the SSID and WEP key after changing the AP

  The Setup is a Linksys BEFSR41 router and a Linksys WAP54G access point.

  Initial Setup used by default no WEP and SSID.

  No problem connecting to my XPS1330.

  Now, I would change the SSID (to distinguish my home network from other networks) and

  Adding a WEP KEY.

  VISTA will allow me to change the current, marked network to home or should I delete this one and start again?

  Thank you

  Bill

  
  

• Tecra A8: Could not establish a wireless connection with encriptación WEP KEY

  Hello.

  I just got a new TECRA A8-143, and I am unable to connect to a 3COM Wireless ADSL Modem when the encriptación WEP key in active. The encriptación turns off as soon as I am connected to the internet, any suggestions!

  Thank you

  My first suggestion is you typed and was using an incorrect encryption key!
  Did you check these settings?

• Cannot connect Router wireless and wireless for windows printer

  I can connect to a wired router and print. But can't do wireless?

  I can connect to a wired router and print. But can't do wireless?

  Given what you have... Yes - no idea.

  If your Windows Vista-based computer has a network inside wireless device and it has the correct driver and software installed and that you have configured the router (if you know the settings) then sees the network wireless on the Windows Vista machine and can configure to match how you have configured the router - there is no reason that you should not be able to connect to the site because you are in-Beach/without any noise between yourself and the router other than equipment of poor quality or poor quality software.

• Help with SQL (sum and last key of table)

  I have a cust_transaction of the table (see def. below)
  
  The data are:
  CUST_ID TIMESTAMP PP_KEY TRANS
  * 39384 2009-10-08 2229345-2 *.
  * 39384 2009-10-09 2229346-1 *.
  * 39384 2009-10-20 2229345-1 *.
  
  What I want is a select statement that sum (trans) but get the last PP_KEY by customer_id.
  So, the result would be:
  * 39384 2229345 2 *.
  
  I tried som on patrition stuff but I saw not just.
  
  Any ideas?
  
  -Table def: +.
  CREATE TABLE TB. CUST_TRANSACTIONS
  +(+
  CUSTOMER_ID NUMBER,
  DATE TIME STAMP,
  NUMBER OF PP_KEY
  NUMBER OF TRANS
  +)+
  TABLESPACE TB
  PCTUSED 0
  PCTFREE 10
  INITRANS 1
  MAXTRANS 255
  STORAGE)
  64K INITIALS
  MINEXTENTS 1
  MAXEXTENTS UNLIMITED
  PCTINCREASE 0
  DEFAULT USER_TABLES
  +)+
  Logging
  NOCOMPRESS
  NOCACHE
  NOPARALLEL
  NOMONITORING;
  
  -INSERTS +.
  TOGETHER TO DEFINE
  Insert into CUST_TRANSACTIONS
  + (CUSTOMER_ID, TIMESTAMP, PP_KEY, TRANS) +.
  Values
  + (39384, TO_DATE (OCTOBER 20, 2009 00:00:00 ',' DD/MM/YYYY HH24:MI:SS'), 2229345, 1); +
  Insert into CUST_TRANSACTIONS
  + (CUSTOMER_ID, TIMESTAMP, PP_KEY, TRANS) +.
  Values
  + (39384, TO_DATE (9 OCTOBER 2009 00:00:00 ',' DD/MM/YYYY HH24:MI:SS'), 2229346, - 1); +
  Insert into CUST_TRANSACTIONS
  + (CUSTOMER_ID, TIMESTAMP, PP_KEY, TRANS) +.
  Values
  + (39384, TO_DATE (8 OCTOBER 2009 00:00:00 ',' DD/MM/YYYY HH24:MI:SS'), 2229345, 2); +
  COMMIT;

   SELECT customer_id,
    SUM(trans)       ,
    MAX(pp_key) KEEP (DENSE_RANK FIRST
  ORDER BY TIMESTAMP )
     FROM cust_transactions
  GROUP BY customer_id
  

  Ravi Kumar

  Published by: ravikumar.sv on December 4, 2009 16:10

• Help with router, crashing, mario kart wii, question

  I seem to have trouble with my router, I have the latest firmware installed and have tried repeatedly to re write the firmware for the router BEFW11s4 V 4

  1. when I go on a site for example bbc.co.uk/radio1 and try to listen live at a show, or 'listen again' my router goes down, and I have to restart my router every time.

  2 - while connected to the router using the nintendo wii, after 20 minutes of online game an error message saying that I need to restart the wii. and the game closes its doors, this seems to be a problem with the exact configuration of my router after a google search, and a lot of people have mentioned certain ports need opening, but I'm really not sure on how to do this, as I don't want to spoil things.

  any help appreciated, Lee

  I ended up buying a new router wrt160n and its solved the problem

• Router WRT160N - Macbook Pro can connect but not Internet

  For some reason any my macbook pro can no longer access the internet wirelessly through my WRT160N. It works very well through a cable connected. I can even connect to the wireless router - full signal and get only one ip address, but it does not connect to the internet - via my browser - I get "cannot find server" and "internet connection doesn't seem to work." Or other applications that use the internet don't work.

  My mac has always been able to connect to other wireless routers. My router is the latest firmware.

  I tried a lot of the things I found in various forums - redo manual settings of router configuration on the router, security (WEP, WPA, unsecured) settings and one suggesting same zap the PRAM. Any Suggestions?

  If your MAC can connect to other networks / Wireless Router, it must do something with your wireless network...

  In this case a simple reset can help you solve your problem, you need to reset your router to default and then re - configure the router from scratch...

  To reset the router press and hold the reset button for 30 seconds... Release the reset button... Unplug the power cable from your router, wait 30 seconds and reconnect the power cable... Now re - configure your router...

  If your Internet Service is cable follow this link

  If your Internet Service is DSL follow this link

  Adjust the settings on your router wireless-

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the Wireless tab
  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

  If you have a second see computer/laptop wireless if it connects to your wireless network of...

• How can I find the name of the network and the WEP key or passphrase WPA from my computer

  I need to install a printer on my laptop, and I wanted to do it by using a wi - fi connection.  But its asking me my network name and the WEP key or the WPA passphrase!  Of course, you can say I'm not very computer savvy and my son actually made me the laptop for Christmas and it was all set up but now I try to install this printer all on my own and I don't know where I can find this info on my computer.  Help!

  Her often on the back or the bottom of your wireless router.

• mx459 won't let me enter the WEP key number, allows only symbols and letters. How to enter numbers?

  mx459 won't let me enter the WEP key number, allows only symbols or letters. How to enter numbers?

  John

  This might help

  Press the SETUP button on the control panel of your printer.
  Using the arrows, select DEVICE SETTINGS, press OK.
  Select local network SETTINGS, then press OK.
  Select Configuration LAN wireless, and then press OK.
  If a message appears, press the WPS button, press STOP to cancel.
  Select STANDARD INSTALLATION in the next screen that appears, and then press OK.
  Select your access point or router, and then press OK.
  Press OK to confirm the access point name.
  Enter your password using the numeric keypad on the right.
  On the screen where you enter your password at the top right of the LCD screen, you should see a: 1. This indicates you are in digital input mode. If you press the asterisk (*) will be fixed: has or uppercase mode, pressing asterisk with tiny switch. To enter a letter in letter mode, you press the digital key to scroll through the available letters. For example: to enter a letter 'c', you press the '2' three times.
  Press OK when finished.
  The LCD will say "Connected", if the password is correct.

• Need help for WRT160N and Vista

  You don't know if there is still a problem, but that's.

  I have Time Warner cable internet and a router WRT160N connected to my desktop on the 2nd floor, all right, download speed is great, near 740 kb/s most of the time.

  I have a laptop running Vista about 75' away and on the 1st floor. The signal strength is very good, most of the time bars 4. Problem is that the download speed is around 20 to 35 kb/s most of the time if I download anything on the computer directly connected or not.

  This is my wifes computer and she had to take the Vista operating system. I still use XP.

  My question is... is there some switch or command I have to on Vista to achieve best download speed. Or should I say forget the wireless and ethernet cable to the laptop.

  Thank you... Bob

  You can make this change on your wireless router, this will solve your problem and you will get the speed good download on your wireless laptop.

  Open an Internet Explorer browser page. In the address bar type - 192.168.1.1 leave name empty username & password for admin to use lower-case... or the wireless settings, follow these steps: -.
  Click on the tab - Wireless

  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the standard channel at 11-2, 462 GHz...

  - And wireless SSID broadcast should be enabled, and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and not letters) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network.

  Click Advanced Wireless-
  settings > change the tag to 75 interval > change the Fragmentation...
  Threshold to 2304 change the RTS threshold to 2307 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect...

• Printer all in one HP3520 - how to select the wireless network and enter the WEP key?

  According to print my wireless network is detected.

  How to connect the! @# % printer $ fo the wireless network and enter the WEP key?

  Instructions on the HP site tell me to selet NETWORK on the printer control panel.  Well, there's a way to select the NETWORK from the control panel.  It is not an option for him.

  I downnloaded and installed the latest drivers.

  I have restored the default settings.

  How to select the wireless network and enter the WEP key?

  All of HP's instructions seem to be for a newer printer with a touchscreen.

  I want that the printer is connected to my main computer via the USB port.  I want to be able to print wireless phones and tablets.

  My 3520 is not a 'touch Screen' and it has wifi.

  However, the following work:

  Try to open the HP Deskjet 3520 icon, open the utilities tab, click on convert USB wireless, by following the steps on the screen.

  This leads me to believe that ONLY the wireless doesn't work.  I know now that the part of the sentence "Convert USB to wireless connection" is supposed to mean "works like USB and wireless.

  Thank you for your help

• How can I find the WEP key for my wireless network so that I can connect to it?

  How can I find the WEP key

  Steps to find a WEP key:

  1. open a browser (the program used to access the internet). The following process worked for me when using the

  Internet Explorer, Firefox and Opera browsers, although I'm not sure it will work for other browsers (for example

  Chrome, Safari etc.).

  2 type the following in the address bar of the browser. If you use a Linksys router type in "192.168.1.1" and if

  using a type of router Belkin "192.168.2.1". The address bar is the area where the Web pages are typed. It is important

  When you enter there is NO http://www. before the numbers.

  3. If everything is is well past that should open a page which says that Linksys or Belkin.

  3. There may be the need of connection. When you use a Linksys if you don't know what are the user name and password, it may

  always be the factory settings and then enter "admin" for the username and "password" for the password. If you are using a

  Belkin router, the factory settings often come without password, click just send without having to type a password.

  4. click on one) "wireless" or b) "settings".

  5. click one) "Wireless security" or b) "wireless settings".

  6. There should be a page with a specified WEP key.

  7 writing it to the down/copy and use as you wish!

• PC cable loss of internet connection with router WRT160N V2

  I'm new to routers and I just added a router WRT160N (V2).  Wireless through my laptop is great. However, I have 1 PC connected physically to the router. The internet connection is sporadic on this PC. I have "wireless" internet service high speed and sometimes you click internet or check your emails, and there is no internet connection. It seems to be after the PC has been idle for a while. When you click on the internet icon PC on the router not even flashes her - it's like the PC and the router do not speak. If it does not connect, the connection is great. Any help would be appreciated!

  There is a known problem with intermittent connectivity and firmware to build 11 for the WRT160N V2. 11 is the current firmware on the Linksys site. Check if you have 11 build if your router is a V2.
  Downgraded to build 8 fits usually correct these deficiencies, but Linksys told several people that they do not have firmware version 8 to give end users.

  It's ONLY for the WRT160N V2 router. This firmware will not work on WRT160N V1.

  You can find it at http://audipages.com/router/

  Follow download them and instructions to downgrade firmware on this page.

• connection problems router WRT310N and wrt54gs * with DSL

  Until I can return to my apartment and after IPconfig etc. returns I wanted to see if anyone has had the following problem.

  I had a home wireless network set up with a wrt54gs v 5... I think it was BOM.

  A few days ago I tried to get the network key for the new smartphone and my roommate kind of stupidly locked myself and disconnected my phone then my Office Wireless adapted. passing through the standard power recycles and resets all him remains disconnected in the apartment as well.

  I have DSL through verizon, a toshiba satellite a135 with vista installed, all updates of drivers, and a westell 6100 dsl modem provided by my phone company.

  highlights include:

  (1) two nights now troubleshooting and browsing the forum. I have already exhausted simple corrections of linksys on his questions and help section.

  (2) new router, I wanted anyway a new and estimated that he was the problem. So I bought a wrt310N, hung, and he now obtained, there no longer updated set of firmware

  (3) internet connection is fine when I connect to my laptop directly to a dsl modem.

  router 4) implements the home network wireless very well, but with no internet connectivity

  (5) computer wired to the modem connects to the internet. wired computer for router modem does not connect to the internet. with two routers. If it connects not wired and wireless won't be better.

  I'm getting a little tired and tired, not to mention, I didn't my XBOX live fix to remove the stress of working in a military office all day lol

  everything seems to work until the router tries to connect to my dsl provider, at least as far as I can tell.

  and I'll be on the phone/forums with my ISP as well to make sure that I am not he mess up simply forgetting to fill in an optional field with info mandatory lol.

  so... help?

  still, when I go home for lunch I'll post information and specifications of real hardware if someone a little more savvy I know what to ask.

  Any ideas on where I'm wrong now?

  Fixed issue...

  in the end, it's a problem between the ISP's modem and the router that they helped me understand.

  My DSL service had changed their service, so TRP was no longer how they did the connections. Automatic DHCP was the current form. Following configurations of router DSL online provided inaccurate information. I didn't have the time to check with the ISP until yesterday afternoon when I was finally able to make a phone call and clarify things.

  We put the modem into bridge mode, checked some settings on the router, and then everything is back up now.

• Router WRT160N v2 lose wired connections have to restart the router, then all is well again.

  Hi all...

  I'm having some trouble with my WRT160N v2 router, now I use it only to share the internet connection between wired PC.

  I have tride (with the help of live chat) to reduce the size of the MTU to 1300, with no success, also an update of the firmware was informed, but I can't find an update for the version "v2" of the WRT160N router.

  The behavior is really funny:

  -Get random msgs "cable network is disconnected" and "local network connection is now connected".

  * plugged direct cable from my modem to the PC then there is no problem, me makes me believe cables are ok

  -Some sites don't be loading not on two PCs connected to the router, Firefox and IE8 trough during live chat, confirmed the site is up, it's as if something is stuck in the cache of the router or something that prevents some loading sites, sites that happen are random, the browser are not even a real attempt to connect but go now empty.

  -Repair windows and hollow EasyLink advisor will have no effect, Easylink advisor indicates that the connection is good when it doesn't appear, restart the router is always fix the problems (for a while)

  Modem: Comcast Cable

  Router: WRT160N v2

  PC1: XP Pro SP3 connected cable trough using Avast 4 Pro Security

  PC2: XP Pro SP3 connected hollow cable using Outpost Security Suite Pro 2009

  It's very frustrating because you can imagen, I hope someone got some clues for me on this one...

  Thanks in advance...

  Martijn greating

  It should list version 1, 2 and 3, when you go to: http://www.linksysbycisco.com/US/en/support/WRT160N/download

  Here are the instructions to DOWNGRADE the WRT160N V2, DO NOT USE this on VERSION 1 or 3, it will turn your router into a door stop!

  http://audipages.com/router/