Hesitant to import my old photos into Lightroom as they have all been published on my Sony play memories... wouldn't be better to just start with the new pictures that I take every day?  (not published)

Similar Questions

• Hi, I'm rookiee and I just started with the first steps of creating a Web site. the katies-coffee-building file is on my desk and uplouded in the library. That has worked well. Now I'm putting the button in Photo Shop (banner), I have pull down on file/pl

  Message "Hi, I'm rookiee and I just started with the first steps of creating a Web site. the katies-coffee-building file is on my desk and uplouded in the library. That has worked well. Now, I'm putting the button in Photo Shop (banner) in. I pull down on the file Photo Shop button instead and try to select the Banner.psd file. Unfortunately all of the (active) folder is not accessible to all. One is not visibel. Please - need some help here. Thank you.

  @Ach ja, meine Muttersprache ist Deutsch

  You must use the file > Place Photoshop button (Cmd / Ctrl + B).

• Windows 7 does not start with the new msi motherboard

  Yesterday, I bought a new motherboard, processor and 8g of ram in my computer. After all what adjustment and replacement of my old motherboard with the new, I started my computer to find that Windows 7 unbootable not. Instead of windows 7, I get the screen click on BIOS II (2). The configuration screen allows me to launch Winki but not Windows 7 because it was not found. The motherboard came with a utility disk drivers msi and AMD chipset which, when inserted in my hard disk, loads up to Winki. This version of windows 7 (Home Premium 64-bit) came pre-installed with my old mother/computer(Thus, I do not have the windows 7 installation disk) card. Is there a way I need to activate Windows 7 on my new motherboard?

  Hello

  Well, you have some problems. First of all, with a new motherboard you need a new copy of Windows - not only the DVD, but a whole new product key must be purchased. It's just the terms of the license: a new motherboard is equivalent to a new computer, and each computer must have its own copy of Windows.

  So where you buy your copy of Windows 7, I would make sure that it came with a DVD image. Otherwise, you can tell us which version of Windows 7 you (will) actually buy, and we can send you a link to the copy of the DVD for this version of Windows 7.

  To purchase a copy of Windows 7 you can check Newegg.com, here: http://www.newegg.com/Product/ProductList.aspx?Submit=ENE&DEPA=0&Order=BESTMATCH&Description=windows+7&N=-1&isNodeId=1 .

  I hope that answers your question.

  Kind regards

  BearPup

• Satellite 1800-712 does not start with the new HARD drive

  Hello world.

  I am currently trying to install a new HARD drive in my notebook of 1800-712.
  I'm having a few trubbles as my Satellite won't start with my new HARD drive.

  I upgraded my BIOS to the latest version.
  The new HARD drive is a 40 GB Samsung.

  Any suggestions on what I need to do to make it all works?

  THX, Philippe

  Hello

  This device was shipped with 20 GB HARD drive.
  You again is 40 GB.
  I guess that the BIOS does not recognize the HARD drive because of the size.

• I usually use my account from Microsoft to connect, but with the new update that I can not connect with her

  After the new update on the login screen it asks a Skype name and password. I used to use my microsoft account to connect to Skype and therefor have no idea how to connect with this new interface. I tried every password I can think and even changed my password on behalf of microsoft and still can't connect.

  Have you tried the login with the Microsoft account option.

  https://support.Skype.com/en/FAQ/FA12081/how-do-i-sign-in-to-Skype-for-Windows-desktop-with-my-micro...

• I tried to copy the pictures from my digital camera on computer memory card and now I can not find them, and they have all been removed from the map. What should I do?

  I inserted the memory card from my digital camera in the slot on my HP laptop.  I went into my computer and 'file' tab and press "copy".  He asked a folder name called 'Photos '.  I then went in the 'photos' file and it says it's empty.  I then inserted the memory card in my camera and were not the picture about it.  I am so upset... There are 665 photos that can never be replaced.  What should I do?

  Hello

  The operating system that you are running on your computer?

  You may have set the option "Erase after importing" when importing the photos. At the end of the import process, then pictures should appear in the Windows Photo Viewer.

  Open the Windows Photo Viewer and check if you can see these photos.

  Check this link for more information:
  http://Windows.Microsoft.com/en-us/Windows-Vista/working-with-digital-pictures

• Errors with the new Motorola Moto G4 more and WiFi not working not

  Hello, I got a brand new Motorola Moto more G4 64 GB phone two days ago, and since then, I have had several different problems.

  When I started my phone for the first time that I saw that there was an update (after initial installation) and I clicked to install the update and in the end, I received a message saying that the update failed, but I never got re - apply the update again and unfortunately I do not know what was in this update.

  Anyway, the first day I was able to connect to my WiFi at home, but since yesterday my WiFi setting is always off and when I try to tap on the button nothing happens. My phone is not even show the available WiFi connections, because the WiFi is completely turned off (as in airplane mode). When I try to turn on the WiFo then it immediately clicks back OFF - no message or whatever. I have tried several things but essentially decided to do a factory reset, and I also deleted the cache partition.

  After the reset, I get several errors now:

  'Unfortunately not stopped the user interface of the system.',

  "Unfortunately the retail Config Service was stopped.", etc.

  I did a clean reset several times and it happens every time. When I click on them away I can always configure my phone but the WiFi problem. Also after the reset, there is no update available, I found weird because it is the first time. My Android version is 6.0.1.

  Anyone know what to do? I feel that this phone is totally buggy and I would maybe return to Motorola if I can't fix it myself.

  dustinmoris wrote:

  Hello, I got a brand new Motorola Moto more G4 64 GB phone two days ago, and since then, I have had several different problems.

  When I started my phone for the first time that I saw that there was an update (after initial installation) and I clicked to install the update and in the end, I received a message saying that the update failed, but I never got re - apply the update again and unfortunately I do not know what was in this update.

  Anyway, the first day I was able to connect to my WiFi at home, but since yesterday my WiFi setting is always off and when I try to tap on the button nothing happens. My phone is not even show the available WiFi connections, because the WiFi is completely turned off (as in airplane mode). When I try to turn on the WiFo then it immediately clicks back OFF - no message or whatever. I have tried several things but essentially decided to do a factory reset, and I also deleted the cache partition.

  After the reset, I get several errors now:

  'Unfortunately not stopped the user interface of the system.',

  "Unfortunately the retail Config Service was stopped.", etc.

  I did a clean reset several times and it happens every time. When I click on them away I can always configure my phone but the WiFi problem. Also after the reset, there is no update available, I found weird because it is the first time. My Android version is 6.0.1.

  Anyone know what to do? I feel that this phone is totally buggy and I would maybe return to Motorola if I can't fix it myself.

  Hi dustinmoris,

  Sorry to hear that. Since you have already completed a factory data reset, repair indeed is necessary. But you mentioned that the phone is brand new and you received it just 2 days ago, you can go back to where you bought it so that they help you more.

  Kind regards

  Joy

  Motorola support

• Satellite Pro 460 does not start with the new drive in

  I recently received a Satellite Pro 460, but he had no hard drive.
  It starts great without a disc in but as soon as I put a new hard drive in it does not start.

  I thought that it might be again a hard drive, so I pulled out my old Toshiba Satellite with my old drive to work, and yet, it does not start.

  Someone has any ideas why this is and what I can do about it

  I think that you can not do much. Satellite pro 460 CDT, for example, comes with 2 GB of HARD drive. If you try to get it work with similar HDD without success, it may be defective IDE port on the motherboard.

  What HARD drive you are trying to use on this good old classic?

• Pavilion p6 - 2120t: Windows will not start with the new graphics card

  Installed a Zotac GT 740 profile down in my desktop PC graphics card HP Pavilion p6 - 2120t and now the PC does not start.

  HP Pavilion p6 - 2120t CTO desktop PC

  Configuration:
  Intel Pentium CPU [email protected]
  4.0 GB RAM
  Intel HD Graphics Driver version Family: 8.15.10.2291 dated 27/01/2011
  Motherboard: IPISB-CU (Carmel2) (1 open PCI Express 16 expansion slot pins)

  BIOS to Version 7.18

  Running:
  Windows 7 Home premium 64-bit w/service pack 1
  Two monitors (VGA, 1 digital port 1)

  Before installing the new graphics card, I replaced the power supply original 300w with a 400w power supply.

  For starters, I disabled the onboard graphics in Device Manager. Then, I opened the case and installed the GT-740 in the open PCI Express slot. I made sure that the card was fully engaged in the slot.

  I plugged both monitors to their connections voted on the new map.

  When I tried to boot the PC, the digital monitor displays the screen HP (the one that indicates which key support to achieve the start menu) and then frozen. No other entries of key or mouse have been accepted.

  The PC then sounds 4 short beeps (about 10 seconds between each beep) and then a long beep before turning off the signal to the screen.

  Then, I removed the new graphics card on the PC that starts then. I have reactivated the original graphics drivers and the PC then worked normally.

  Tried the above process two more times with the same results.

  I then went into the start menu to look at the BIOS. The menu of the BIOS shows two options:

  > Sources of boot UEFI

  Windows Boot Manager

  > Sources of boot legacy

  ATAP I CD/DVD player

  SATA2

  Hard drive

  SATA0

  Network controller (Realtek PXE B06 D00)

  PC using UEFI Boot Manager Windows boots normally

  I have not tried Legacy Boot Sources because I don't know which one to choose.

  I went to the HP site and looked for an update to the newest BIOS, but updating them is a rev version 7.16 while my PC shows my BIOS to version 7.18

  I know that others have had a similar problem but I have not seen a solution that works for my PC.

  Any advice would be welcome.
  Thanks for your time.

  Hello

  Your PC isn't spec'd to run Windows 7 using the Windows Boot Manager.  I expect to a UEFI-based graphics card likely to work on an HP PC that does not have a BIOS version 8.

  The below listed OEM HP, graphics cards should work in your PC using a normal non - UEFI W7 and W8 installation.

  

• Continually get notification that AOL password is not accepted. If I go directly to AOL it accepts my password. It just started with the upgrade to ElCapitan.

  OSX ELCAPITAN 10.11.2 since this update, I keep getting the message that mail needs password. I know that this password is good, as I can sign directly to AOL, but the iMac has random challenges to get the post. Sometimes, it takes the password and brings in a block of mail, sometimes not.

  Hi Carol,.

  If you encounter a problem with the impossibility of obtaining the email because he keeps asking a correct password, I would say that you are troubleshooting by following the steps in this article - Mail if your Mac keeps asking for your password.

  Thank you for using communities of Apple Support.

  Sincerely.

• SMU 8108 does not start with the new hard drive

  Hello

  I am currently using SMU 8108 with SMU-1062 q.

  The previous record was borken, so I had to install a new hard drive.

  The new hard drive is fommatted as NTFS format, and it is currently mounted on 8108.

  Unfortunately, I don't have recovery disk available to the general public so I am trying to install Windows 7 on a blank hard drive.

  When you start, the LED OK PWK light is all the time, orange DRIVE LED turns on for a few seconds only when I turn on the switch.

  LabVIEW RT switches are all off, I cleared CMOS several times to the Board of Directors, but the screen does not show anything.

  I tried to use my DVI monitor with any other device as well, and it worked, so there is no problem with the monitor.

  In addition, I tried to go in window safe mode by pressing F8 or Del it didn't work, so I can't see anything on the screen when his kick upward.

  I tried to put a lot of information I can it will be very appreciated if you can help me with this problem please.

  You said that you can't in Windows safe mode, you have installed Windows on the hard drive?  Are you able to get into the BIOS of the controller?

  If you are not able to access the BIOS for the controller, it may be due to bad RAM.  If you are uncomfortable installing RAM and you have a few extra laptop RAM of the same type (I think it's the DDR3 for your controller) laying around, you can try to replace the RAM.

  Was your hard drive damaged through certain events, or it just stop working?

• Help! X 60 does not start with the new 320 GB HDD...

  I try to get a 320 GB Seagate Momentus 7200.3 SATA drive working with my thinkpad X 60 1706-M7M.

  I cloned my existing OEM Hitachi 80 GB to the new drive using Acronis True Image. So far, I've done this four times, so I think that cloning is not the issue.

  BIOS changed in compatibility mode.

  The strange thing is that the rescue partition and recovery works but not the windows bootable partition?

  I see also all files on the new drive, both partitions are visible when it is plugged in via the USB enclosure. They look very well.

  I tried to make it work for 3 days and I'm ready to throw the laptop out the window!

  Thanks in advance.

  If you are ready, I would recommend using Easeus Disk Copy. It is a bootable CD that will clone the disk sector.

• With the new update version 29,0 gmail does not work?

  Whenever I try to open gmail, this gives:

  The page is not redirecting properly

  Firefox has detected that the server redirects the request for this address in a way that will never end.

     This problem can sometimes be caused by disabling or refusing to accept cookies.
  

  Otherwise, all other Google products work very well! Gmail only works.

  If you have not already tried to delete your existing Google cookies, please try this. You can load the Google search, then either:

  • Click on the padlock in the address bar > more information > Security > "View Cookies".
  • Right-click the page and choose View Page Info > Security > "View Cookies".
  • Menu Tools > Page Info > Security > "View Cookies".

  In the dialog box that appears, you can delete cookies from Google.

  Then try to reload the page and sign in again. Who help me?

• C55-A-1MW satellite does not start with the new RAM inserted

  Hey.

  I hope to find someone who can help me... I bought ram memories and tried 4 different memories in my C55 A 1MW Satellite. But each card RAM I have insert makes the computer cannot start... It lights just to stop again.

  Is there a compatibility issue or anything like that? I used 2 different aData Ram extensions cars, 1 1 and 4 GB 2 GB. the 4 GB card was 1333 mhz and was 2 GB 1600 mhz card. and I tried 2 corsair 4 GB 1600 mhz different cards.

  Is this something that makes only able to expand RAM with Toshibas own memories or is the second cardslot for broken RAM memory?

  As I see you use RAM modules with different specifications. Your problem is certainly of RAM compatibility and you must use the RAM modules with the same specifications.
  According to specification of laptop there are 4 slots of memory and laptop can handle up to 32 GB of RAM.

  The compatible RAM modules are:
  4 GB DDR3L-1600-PA5104U-1M4G
  8 GB DDR3L-1600-PA5104U-1M8G

  Of course, you can use modules from other manufacturers, but please do not use some cheap products. I can recommend the use of Kingston memory modules.

• Satellite L30 10Y does not start with the new RAM modules

  Hello
  regged just with this forum I have a problem to upgrade memory.

  I read through a few problems of memory here and all users that it is a problem of memory comaptible. I got Hynix 512 MB RAM in my laptop and I bought 2 x 1 GB memory Hynix these two are match sticks to the installed memory, but when I installed my laptop wouldn't boot at all. It would only boot if I had a stick in both.

  I tried to switch ports top and btm and even when a stick was installed it says in XP, Vista and Windows 7 (yes I tried all systems) 896 MB of available space. I even tried to use my other Hynix stick, but he won't start and showed more stick of 1 GB (896 MB usable in Windows 7). After reading all the threads I wonder if it is a hardware failure or is there a fix in the world of Toshiba or perhaps in the world of Toshiba, the L series is almost obsolete and not worth to help people who unwittingly bought their goods.

  I apologize for being slightly down on Toshiba but a laptop that shows what he can work and is not a company should hold his hand up and say that Yes, there is a fault and help deal with the problem.

  You see 896 MB, because the rest is reserved for VRAM for graphics card.

  Sometimes RAM may simply be incompatible, because of incompatibilities of calendar or RAM chip/controller design differences.

  What speed and timings is your original RAM?
  PCxxxx / DDRxxx =
  Schedules CASES/RAS =.

  What speed and timings is your new RAM?
  PCxxxx / DDRxxx =
  Schedules CASES/RAS =.

  You can display this information using a utility called CPU - Z
  http://www.CPUID.com/cpuz.php