HID of USB 2.0 high speed, broadband, end points supported for windows 7?

Similar Questions

• How can I add a USB host controller high-speed to my PC?

  My OS is windows xp home edition. I get this message that the HI-SPEED device attached to Non HI-SPEED USB Hub.

  The USB Composite device is a USB HI-SPEED device and will function at reduced speed when plugged into a port not HI-SPEED.

  There is no host controller USB HI-SPEED installed on this computer.

  Recommendation: You add a USB host controller high-speed on this computer in order to get maximum performance.

  So, how can I add this USB host controller high-speed to my PC? Is - this material I must add and physically install to my PC?

  As always, any help is greatly appreciated.

  Thank you!

  drake68

  Hi Drake,

  Review the devices USB connected to your PC and make sure that there is not a USB 1.x device connected to the same USB HUB (front or rear).  USB 1.x devices will cause the USB HUB at the bottom shift to 1.x speeds.

  You have an old PC (2002), it is possible that your PC does not have a USB HUB 2.0.  In this case, you need to install a USB PCI adapter card.

• upgrade to usb host controller high-speed

  I received a message that my device could run faster if I have upgraded to a usb host controller high-speed. Is this something that I can download or I have to buy a new usb controller? Thank you, Kevin

  If your system is old, it may have have USB 1.1 ports. Only way to fix it (if you use USB 2 devices. Either buy USB 2 PCI cards), or upgrade the system. If you get / have ports USB 2

• IdeaPad Flex 2 - 14 d: constantly running at high speed of the fan: 8.1 Windows

  Hello.

  I have a Flex 2 - 14 d running Windows 8.1 Ideapad and real pilots.

  The fan runs constantly at high speed.

  So I have no complaint about overheating, but instead, I have to complain about is cold knees.

  Y at - it a possibility to adjust the fan speed?

  Best regards

  Eleichstetten

  I have Flex 2-15 and suffered from the same problem. By trial and error, I found that (although not documented) a specific version of the TPFanControl (http://www.staff.uni-marburg.de/~schmitzr/tpfc.html) does not work with my laptop. Opt for the 0.62e version. It is a cool utility, has several conditions of default security in standard BIOS procedures if something is still wrong. Temperature to the fan speed mappings are user adjustible, so you must refine your laptop (default values are designed for Edge E520, so don't not necesserily ideal).

  A HUGE relief!

• Card high speed does not work after installing Windows Service Pack for Vista

  I just installed Windows Service Pack for Vista and now my card Sprint high speed does not work.  The message I get is that the "peripheral No. is recognized. I was using the card top debit without any problems for over 6 months.

  What can I do to get this corrected.

  John

  Assuming that the Vista SP2...

  Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support, initially planned to end on November 26, 2009, has been extended until February 26, 2010. Availability of support chat or messaging differs depending on your location. Some questions may require that more support for which he is advanced a charge.  Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; ( Problems after installing a service pack). ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Lost USB 2.0 high speed

  I did a Clean install of Windows 7 in my HP Media Center PC m1160n, who had a Media Center XP on it. Now every time I plug into a USB port (6) I get a message back that I should use a USB 2.0 for faster operation. I do not know where they were going, they were USB 2.0 under the o/s XP but seems to have lost the drivers for them now. If I goto Device Manager, I find (Standard Enhanced PCI to USB Host Controller) with 2 USB Composite devices USB Mass Storage Device, USB print media and 4 USB hub root. But as I said, if I plug it into one of the ports is one of the 4 back or one of the 2 in front with my USB webcam it reports he would run faster on a USB 2.0 slot. What am I trying to find USB 2.0 for this drivers and install?

  HP Media Center m1160n PC

  SER # MXK4450W0P

  Prod. # HP Media Center M1000?

  Old operating system XP Professional

  New o/s 7-Ultimate window

  USB 1.0 devices connected to a hub will give the speed from 2.0 to 1.0.  Keep your devices USB 1.0 on separate hubs.

• I'm supposed to have access to high-speed broadband. How can I enter the access code?

  Hello

  I am currently resident in a property with connection broadband, and I do not know how to enter the code to access the internet.  Any assistance is welcome.

  Kind regards

  Clare - Technophobe

  [Original title: Please help]

  Hello and welcome!

  If you are experiencing internet problems, I would recommend that you contact your internet service provider.

• USB missing on hp 15-b041dx after down ranking for windows 7 64 driver

  I uninstalled windows 8 on a 15-b041dx hp and installed windows 7 64-bit.  I have all the drivers usb excenpt the hardware id is VEN 8086 DEV 1e315subsys 1900103c rev4 anyone know where can get the windows 7 drivers for this machine?  I found out it is a chipset intel but I am at a loss.

  Thank you

  Mark

  I FOUND IT HERE - > http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063 & lc = on & cc = us & dlc = in & sw_lang = & product = 5278311 #N269

  The USB chipset worked!

• Ports high speed USB Equium A100

  I installed a webcam Advent (before exchanging it for a better creative). Part of the installation process involves installing a Microsoft's USB controller. (OS is Windows XP Home Edition). I uninstalled the ADVENT software when I got back to the webcam.

  Since then, I started getting messages every time I plug a USB device, on a device high-speed, requiring a port high speed.

  When I look in Device Manager, I have two sets of Bus USB controllers:

  One includes 2 standard OpenHCD USB host controllers, 2 USB, 1 support 2 USB hubs and USB printing composite devices. Their drivers are dated 2001.

  The other includes 1 class PCI USB 2.0 enhanced host controller and USB Root Hub Device 1. Their drivers are dated 2006.

  I have 4 USB ports and all seem to be using the first series of USB controllers. If I disable one of the controllers, then various USB devices stop working.

  As my laptop is only 18 months old, I would have thought that all USB ports are 2.0 version?

  How can I 'forcing' the laptop to use the second set of controllers?

  Hello

  I think that the biggest problem, it is you would waste more time to fix such a driver related issue then just entering the recovery CD and performing a recovery of your entire system.

  Perhaps the fastest way to put little life back to your ports USB 2.0 high-speed. Otherwise, I had suggested to remove all ports from the Device Manager and let windows after a restart re-install all the drivers, but before perform the reboot it would be better to manually remove all THE drivers installed previously.

  Maybe it helps, but if not he would have definitely better to perform the recustomization...

  Concerning

• Message: This device can perform faster if you connect high speed USB

  Hello

  I have a laptop Toshiba Satellite 2009 of Vista.
  I just bought a multimedia design Memup Feel of the disc hard 500 GB.

  My concern is that when I connect to my PC, I have the following message:
  + This device can perform faster. USB devices can be faster if you connect to a USB 2.0 high speed +.
  + To get the list of available ports, click here. +

  Then I have a list of ports in bold, but I don't know what to do with.

  How to solve my problem?

  Thank you

  Hello

  Are you sure that your laptop is Satellite 2009?
  I put t know this model of laptop.

  But I know that this error message; This message appears if you connect a USB 2.0 device to a slower USB port; That is, USB 1.1
  But I think that your laptop supports USB 2.0 ports either TI problem disc external HARD s or the issue of USB drivers
  Try updating the chipset driver you can also delete all the USB controllers and hubs in Device Manager ports. Restart the unit. After restarting again the OS would recognize all USB ports.
  Then try to reconnect the USB HDD

• Satellite A100 - the fan runs at high speed after idle standby

  Hello

  My laptop is Satellite A100-912.

  The problem is when I suspend it for more the a few minutes when the fan is running at high speed. This occurs on both Windows XP and Linux GNU. When the temperature of the two nuclei will more then 51 degrees C fan slows down and begins to work as expected. Suspended for a short time (about a minute or two) the fan speed is OK.

  I've updated to the latest version of the BIOS.

  Hello

  What version of BIOS you have installed? Has recently been the machine in for repair? A few interesting facts where I need some information to help you...
  By the way: is your machine still in warranty?

  Welcome them

• HP Compaq DC7800p Convertible: Fan never works at high speed

  Well Hello hp. My question is that I have the hp compaq dc7800p with intel q35 chipset. I also have the intel core 2 duo e6750, who comes to 66 without high-speed fan spining. I checked, the site of intel, that it is said that Tcase is 72 C I also have the problem with the chipset, there too big temperatures when you play. It goes up to 80 C. What I would do. Should I change cpu fan or don't start high speed at 70 ° C and for the chipset how cool up to at least 60 C, I have the normal aluminum without cooler chipset. I play the games are battlefield 3 and 4 and yesterday my pc freezes, and when I rebooted funs went at full speed, but nothing showed on the screen for 5 minutes, is now well, fortunately, but I all wory to much.

  Temperatures look ok so far.

  -In addition to being very energy efficient - Core2Duo processors have built-in thermal protection.

  If ever they come to high temperature, the frequency is decreased. If temperatures reach critical CPU turns off.

  Chipsets get usually a little hot under load.

  80 ° C is still about 25 degrees below criticism.

  What graphics card you have?

  As far as I know, feeding in these machines has only about 360 watts, which is not enough for some high power graphics cards. It is most likely the reason why your PC freezes. Video games cards consume not only a few watts, they also generate a huge amount of heat under load.

  Anyway, there are two things you can do:

  First, go to the HP Support and get the dc 7800 manual.

  Uninstall the CPU cooler and apply new thermal paste (don't forget to clean the old one).

  Then, increase the speed of the fan slowed down in BIOS F10 for better air circulation.

• How to configure a modem high speed in windows 98

  1. I have my old emachine running windows 98 Second edition, the problem is im trying to get my modem to broadband installation cricket, but he he reconizes just as usb mass storage, my pc running windows xp media with oem edition broke down cannot get to windows will not let me type in the command line. IM lost as to fix one and other to get online, I have the disc that came with both computers and they were pre-installed so I guess as its oem.

  Hello

  Support for Windows 98, Windows 98 Second edition and Windows Millennium Edition (me) ended on 11 July 2006. However, you may read this article for general troubleshooting of USB.

  http://support.Microsoft.com/kb/263218

  What about XP, we would need more information.

  1. what exactly caused your computer down?
  2 did you change your computer, after which the issue started?
  3 have you tried booting in safe mode?

  http://support.Microsoft.com/kb/555375

• How to change the speed of the pointer mouse?

  Hello

  I want to increase the speed of the pointer of the mouse through LabVIEW. Similar to change the speed of the pointer mouse in Windows "mouse properties".

  Thanks in advance.

  Here

• Portage Z30-A-13W connected to the high speed Port Replicator III - USB problems

  Hi all.

  We recently bought a new Portage Z30-A-13W and Hi-Speed Port Replicator III.
  Setting network and graphics work correctly with port replicator, but the USB ports don't work at all.

  I tried the port replicator USB 2.0 and USB 3.0 and I can't seem to work with a keyboard, mouse, USB key or a mobile phone.

  In the case of mobile phones, it is also no output power of the ports that the mobile does not start to load.

  At any one another experianced this problem and what was the resolution.

  Thank you very much

  Jonathan Davies

  Hello

  As far as I know additional drivers are not really needed to use the USB ports.
  This is why I m wondering why don t USB ports work.

  It might be possible that ports high speed Port Replicator III USB are faulty, but to be honest, I can't imagine that all 6 USB ports may bad work at the same time.

  So maybe it s a software problem.
  First of all, I would recommend the default BIOS and check the USB legacy support for keyboard and mouse could be activated.
  After access to the Device Manager and remove / delete the USB hubs and controllers in the list of devices.

  Keep high speed Port Replicator III connected to the computer and restart the device.
  Usually, the system should recognize automatically deleted USB ports and must update the drivers of USB ports.

  I hope that the USB ports don't work after this short workaround solution.
  Keep your fingers crossed.