High with e1200 latency

Similar Questions

• Linksys E8350 have problem with some latency every bit of packages

  Hello

  I have the problem with latency high each 6 pack when I try to ping IP of the router via wifi.

  $ ping 192.168.1.1
  PING 192.168.1.1 (192.168.1.1): 56 data bytes
  64 bytes from 192.168.1.1: icmp_seq = 0 ttl = 64 time = 3,437 ms
  64 bytes from 192.168.1.1: icmp_seq = 1 ttl = 64 time = 2,957 ms
  64 bytes from 192.168.1.1: icmp_seq = 2 ttl = 64 time = ms 3,392
  64 bytes from 192.168.1.1: icmp_seq = 3 ttl = 64 time = 3,715 ms
  64 bytes from 192.168.1.1: icmp_seq = 4 ttl = 64 time = 3,284 ms
  64 bytes from 192.168.1.1: icmp_seq = 5 ttl = 64 time = 386,280 ms
  64 bytes from 192.168.1.1: icmp_seq = 6 ttl = 64 time = 427,748 ms
  64 bytes from 192.168.1.1: icmp_seq = 7 ttl = 64 time = 53,266 ms
  64 bytes from 192.168.1.1: icmp_seq = 8 ttl = 64 time = 523,208 ms
  64 bytes from 192.168.1.1: icmp_seq = 9 ttl = 64 time = 3,666 ms
  64 bytes from 192.168.1.1: icmp_seq = 10 ttl = 64 time = 2,508 ms
  64 bytes from 192.168.1.1: icmp_seq = 11 ttl = 64 time = 3,440 ms
  64 bytes from 192.168.1.1: icmp_seq = 12 ttl = 64 time = ms 3,579
  64 bytes from 192.168.1.1: icmp_seq = 13 ttl = 64 time = 2,608 ms
  64 bytes from 192.168.1.1: icmp_seq = 14 ttl = 64 time = ms 3,154
  64 bytes from 192.168.1.1: icmp_seq = 15 ttl = 64 time = 326,885 ms
  64 bytes from 192.168.1.1: icmp_seq = 16 ttl = 64 time = 371,978 ms
  64 bytes from 192.168.1.1: icmp_seq = 17 ttl = 64 time = 2,855 ms
  64 bytes from 192.168.1.1: icmp_seq = 18 ttl = 64 time = 469,882 ms
  64 bytes from 192.168.1.1: icmp_seq = 19 ttl = 64 time = 2.841 ms
  64 bytes from 192.168.1.1: icmp_seq = 20 ttl = 64 time = 2,563 ms
  64 bytes from 192.168.1.1: icmp_seq = 21 ttl = 64 time = 2,477 ms
  64 bytes from 192.168.1.1: icmp_seq = 22 ttl = 64 time = 3,560 ms
  64 bytes from 192.168.1.1: icmp_seq = 23 ttl = 64 time = 3,572 ms
  64 bytes from 192.168.1.1: icmp_seq = 24 ttl = 64 time = 2,605 ms
  64 bytes from 192.168.1.1: icmp_seq = 25 ttl = 64 time = 278,522 ms
  64 bytes from 192.168.1.1: icmp_seq = 26 ttl = 64 time = 325,989 ms
  64 bytes from 192.168.1.1: icmp_seq = 27 ttl = 64 time = 687,060 ms
  64 bytes from 192.168.1.1: icmp_seq = 28 ttl = 64 time = 417,529 ms
  64 bytes from 192.168.1.1: icmp_seq = 29 ttl = 64 time = 2.659 ms

  Latest firmware 1.0.02.9. Router has been reset to factory default and firmware has been restored.

  It is made from material? You guys can recommend?

  I think that it is a Wireless Mac driver problem. I've seen this symptom in reverse when ping Mac from another computer on the network. My Mac Mini has similar problems and I have tested a lot of the router. The departure of ping well off the coast and then ramps up really bad and then cycles to good. I have found no solution but my Mac Mini is still usable and the flow seems good, just with a latency.

• Slow buffering when shooting in burst mode high with my 7DMarkii... What is the fastest SD card?

  When shooting in burst mode high with my 7 D Mark ii, I do not get optimal performance... the buffer fills up fast and backup... while I can't take shots more... I disabled the quite high definition noise reduction... Usually, I only have an SD card in the camera. I do not use the other card slot... is it because I didn't have the fastest SD card... For those of you who shoot regularly 7 D Mark ii, make it a point to always shoot with a SAndisk SD 95 map... ? I'd get better performance if I used the slot for CF card or both?

  IRIS says:

  I'm shooting with a single card (SD), a Lexar pro 64 GB 150 MB/sec Class 10 and 3 inside the U (whatever that means), but I show a limit 16 popping up on my screen... so I do not understand... I'm shooting a low ISO... I have disabled noise reduction... I'm shooting a Standard picture style... I'm shooting RAW only... My battery is charged... Then why is it backup and buffering so often? I forgot something? is it's just that the CF card is faster? .... I doh't understand why I don't get the perfromance promised high 20 + something burst shots...

  First of all, Yes, CF cards are faster.

  Second, the number you see is the current buffer and does not include the write speed of your card.

  The only way to tell what your real brightness issue is therefore to test.

  Shooting RAW to SanDisk Extreme PRO 32 GB 160 MB/s UDMA 7 CF Card, I get about 30 shots before the outbreak slows. My viewfinder shows 15.

  Note When your feature of gust of defined test cards your lens to manual focus (MF) because according to your settings of priority to focus the camera auto focus can slow or even stop your glow.

• I'm latency getting high with all my games. Wow cs dod tf2.

  I am running windows 7 32 bit and my network drivers and video drivers are all updated. But I get about 3 times more latency as I did with XP 12 hours ago. Nothing has changed other then upgrade the operating system. {wow} is 300ms, and peaks at 1500 [w7] 150-180ms with [xp] ({CSS} 90-170ms [w7] 10-20 [xp]).

  Well, it could be that your network drivers are not very good and they need to come out with a better update.  Or you can have the rest of the network traffic that you aren't aware of.  If the problem persists, try asking in the forum of the network, they are able to help you in tracking down the issue.

• Win 7 BSOD, high with ndis.sys latency

  My laptop has experienced slow load time, audio popping/cracking. I also got BSOD when trying to restart/shutdown. It of like it since Oct/Nov ' 14 and did not get better. I uninstalled it, rebooted and will fix temporarily the problem, he'll be back in a day or two. All my drivers are up to date, no viruses or malware. No memory problem. Laptop works very well except for latency, whenever I go online to browse the internet or play a game.

  In addition, I'm unable to load the minidump file. When I try to load it OneDrive, I get an error saying: the file is empty. I can't download it from WinRar, "access denied." I am the only user on my laptop computer account.

  Any help is greatly appreciated.

  FM

  This phenomenon was linked to the pilot of packet filter NetGroup, part of the WinPcap packet capture library (list of programs that use it: http://www.winpcap.org/misc/links.htm )

  I just want to remove this

• Satellite A300-1IE - CPU usage high with Bluetooth active

  Hello!

  I recently installed Windows 7 and the Toshiba Software Installer on my Satellite A300-1IE.

  I have a problem with the bluetoothmanager, it's more than double the CPU usage when turned on. When I close the CPU usage goes down.
  This is not normal?

  When the BT active CPU usage is 9 to 15% and when not 1-3%

  Seems to be high. Try an update of the Bluetooth stack.
  http://APS2.toshiba-tro.de/Bluetooth/?page=download
  Ensure that you answer the question during the uninstallation, if all configurations should be removed, with Yes.

• Qosmio G20: CPU too high with video usage

  Hello

  I've got G20 (2.13 Ghz processor) and nVidia 128 MB GeForce Go 6600 and I noticed that when you run video that my CPU utilization goes up high enough. View tv goes up to about 80%, video in media player substantially the same, but the video clips on Web sites and sites with video banner Web can get up to 100%.

  I don't know if this normal that I had not really noticed before, but lately, with this hot weather, I found that on the days hottest occasionally my system stopped, probably because the fan may not follow.

  My question is if these ages CPU usage % are normal for this system, or I have some setting wrong that puts the load on the processor and not the graphics card. Can someone tell me if I can check how the video processing is done by the graphics card or how I can assure that this is the work and only in passing on overloading the CPU.

  Thank you very much.

  PS I am running the latest drivers video for this machine, obtained from the Toshiba draft.exe page.

  Hi William

  I had a lot of experiences with Qosmio G20 and activity of the CPU under pressure. With the use of the highest processor unit was never overheated just a little harder because of cooling fan.

  As you know Qosmio G20 is powerful multimedia and video unit problem described in your message is really strange. If you wrote that you don't l l notice that before, I assume your personal configuration is responsible for this. On this path, it is not easy to say why this is happening. Try to check the processes running and at the end all of them you don't need. On this way the CPU use should be much lower.

• How to achieve high with Dalsa GigE camera

  Hello everyone

  I have dalsa spyder3 line-scan Camera, GigE, who says it's scanning line 36KHz device. But when I run this camera at the maximum rate of the line in labview and display data using a while loop, I do not reach the specified line 36KHz rate. To capture all frames that I have to use a capture card or there is a way to achieve this rate of line using another technique in labview. Please help to in the present.

  Concerning

  Charles

  Hi Charles,

  I realize that this is a line scan camera. However, the Spyder3 has the ability to buffer multiple lines in a single image. It is also highly critical of GigE Vision because there is a certain amount of load image by image, which would be very important to the rates that you will. By default the camera should give you more than one line per image - you should have manually configure for a smaller amount.  If you have configured to do one line per image, then it is likely that you drop frames in the acquisition or in your processing loop - two would probably have to follow with 36Khz rates. However, if you get a hundred or a thousand lines per image, then the load becomes trivial and you should have no problem to reach your desired line frequency.

  Eric

• Firepower - High CPU and latency

  Hey

  IM under firepower with a 5555 X. The FireSIGHT console to manage using.

  When sending one of our internet connected interface through the CPU power of fire leaped up 25-30% on the SAA and the latency rises with 40-150ms.

  I need to know what is the cause, Cisco licenses is expensive and I didn't know HW would pose a problem.

  The problem is worse when traffic increases. When you reach 600-700mpbs the ASA thus removes the packages.

  Thanx.

  You are very lucky if you can push 600-700Mbit/s through the FP module in your X-5555.
  With functionality STROKE and IPS, it is evaluated to 450Mbit/s, yet further with the URL and the amp on.

  If you need the functionality of the ASA, you should go with either:

  5585-X SSP EP 10/40

  SSP 5585-X 40

  5585-X SSP EP 20/60

• FT clusters supported in VMware stretched with 2ms latency?

  A client just wonder if FT is supported in a tense situation where data centers have 2ms max latency?

  I could not find this recommendation is subsidiary of millisecond latency < 1ms?

  • At the very least, use 1 GbE NIC for VMware FT logging network. Use 10 GbE NICS for increased bandwidth of FT
    
    
  • logging traffic.
    
    
  • Make sure that the latency between ESX hosts is sub millisecond latency is recommended for the
    
    
  • Network logging FT. Use vmkping to measure latency.
    
    
  • VMware vSwitch parameters on the hosts must be as uniform, for example using the same VLAN for VMware ft logging, to make these available hosts for the placement of VMs school enter a VMware® vNetwork Distributed Switch to avoid inconsistencies in the settings of a vSwitch.
    
    

  If it is better or not is not for me to decide who belongs to the client.

  In any case, two things:

  VPLEX is access anywhere, if fail the primary and secondary levels would resume their would be no real performance hit, just for a short period probably. There are 1 million documents on VPLEX there, I suggest you read those.

  Lag time, no matter what kind of latency will slow the VMs. latency is nothing more then a 'delay '. So if the latency increases your virtual machine slows down.

  See the white paper of vMSC to a feeling on what could play a role with an extended cluster, it is not as easy as many make it sound:

  http://blogs.VMware.com/vSphere/2012/05/vSphere-Metro-storage-cluster-white-paper-released.html

• Free/busy options high, with no shared storage

  Here is a little history on our Setup. CurrentY we run vmware server 2.0 on centos 5.4 on both servers in a data center to remove. Currently, what we are doing is a manual process to a level of poormans HA. We create a snapshot of the virtual machine (sometimes) and you use rsync to synchronize the virtual machine on the other server. Each server has 2 mirrored disks and disk 1 not mirrored. If each server synchronizes the reader not mirrored.

  I have a key for the company left, I wonder what would be my options for maximum availability with the two servers and HA. We would like to have the opportunity to have HA and FT, but the shared storage is not an option right now.

  Thank you!

  All VMware high availability options require a shred storage.

  You can create virtual shared storage on warehouses of local data (updated mirror network) with the Virtual SAN PHDVirtual, HP Lefthand VSA or StarWind iSCSI.

  ---

  MCSA, MCTS Hyper-V, VCP 3/4, VMware vExpert

  http://blog.vadmin.ru

• To access a medical database, a software print said I need now of TLS 1.1.  Printing the program says that if I get the good Lion 10.7.5 OX I should get the Safari 7.0 or higher with him.  I can't find the procedure to download Safari.

  Friends:

  I have a MacBook Pro - 2.3 GHz Intel Core i 5.  MEM at 1333 MHZ 4 GB DDR3.  My MAC OS X LIon is version 10.7.5.  MY current version of Safari is 6.1.6.

  I tried to connect to a medical/pharmacy/base database program and told me that I don't have a high enough version of TLS.  I have 1.0 and 1.1 is required.  The Lion of MAC OX 10.7.5 should have a version of Safari 7 that TLS 1.1 in - level items or can be upgraded to the level of TLS 1.1.  I looked at my app updates and do not find the update of Safari to 7.   No idea where in the system support or at the Apple retail I can get the update?  Thank you.

  Safari 7 is a very outdated version of Safari.

  Update of Safari, the only is to update your Mac to the new OS X El Capitan. Install it the latest Safari version 9.1.2.

  So see if your Mac can run El Capitan > update of OS X El Capitan - Apple Support

  An alternative would be to use the Firefox browser that still supports v10.7 > https://support.mozilla.org/en-US/kb/how-download-and-install-firefox-mac

• High with NEITHER 5673E scanning frequency

  Hello! I want to use the generator NOR 5673E. In the examples, I found the "scanning frequency" example for 5673E.

  My question is: what is the maximum speed of the generator can sweep. How to estimate time frequency of scanning program? For example, I have the range of frequencies from 2 GHz to 3 GHz, step 1 MHz. how long will it take? What is the shortest time as possible

  with the scan step frequency = 1 MHz, 0.1 MHz? Milliseconds, microseconds can nanoseconds?

  Hello

  On your SMU-5673E RF list mode will be the most effective approach for your scanning application.  The smallest you can get the duration of the step is 5 US on this material.  However, the speed at which you scan should be a factor of your specific needs, such as the frequency and accuracy of power (more adjustment time necessary for better performance).  Larger step sizes will require tuning more time for equivalent performance.  It is also interesting to note that the maximum amount of steps (limited by the amount of memory on-board) in the list view is 250.  This means that you will need to reconfigure your scan after 250 MHz (1 MHz/step * 250 not) in the software.  At this point, your total scan time will depend on the performance of your computer.

  I would recommend that you take a look at the SMU-5673E sheet beginning on page 5 learn more about tuning time.  Also, here is a link to obsolete documentation, we have online for RF list Mode:

  List of configuration - http://zone.ni.com/reference/en-XX/help/371025K-01/TOC112.htm

  For the most complete documentation and up to date on RF list Mode, please see the help of your computer RFSG documentation.

  Kind regards

• How to measure how long a Boolean value is high with thick County?

  I acquire the impulse response of a parallax Distance sensor, but I I don't know how to measure the number of features that this signal is high (the time of the input signal is high is proportional to the distance). I would like to reset the counter thickness when this signal is low. is this possible? Y at - it another option?

  Thank you...

  for (imstuck) wrote:

  You will need to adjust some if you want an indicator of up-to-date at all times.

  Here is a very minimalist version which updates the timer continuously while the switch is on and holds last value when the switch is off. Try it!

  

• With E1200 slow download speeds

  I have an E1200 that will work very well for a while, then suddenly the download speed for all wireless devices will be reduced to between 20-30 KB/s.  It happened last night when we were watching videos on Hulu.  We were explosive along the end, when all of a sudden the connection was pretty awful that it had to stop watching.  We have no idea of what has changed – there is only two of us in the House and we were both passively watch Hulu.

  It's already happened, and generally change something like the wireless channel fixed it, but not this time.

  The computers that we have connected to the router via Ethernet gets stuck between 1 to 3 MB/s, so I know that's not the modem or the access provider.

  The intensity of the signal is good (4-5 bars).  I tried to reposition the router and the wireless receiver, but that did not help.

  I have the latest firmware for the router, as far as I know (v2.0.02).

  I tried all channels available (including the ' Auto').  I tried to change the width of the channel between Auto and 40 MHz.  I tried to reset the router to factory settings and re - download my configuraiton.  I tried to set QoS.

  Any other ideas?

  Hmmm I have a router E4200 and had the same problem. But when I disabled it Support WMM and I was able to make it work properly.