Hitachi touro usb 3 hardrive does not work in windows 8

Similar Questions

• USB Flash drive does not work with Windows 7 Pro 64-bit

  I have several USB thumb drives, some of them do not work when I plug them in while others work very well. By experimenting, I reduced the problem with the 64-bit Version Windows. All of these USB keys works well in my other computers that have 32-bit installed and also even computer with the 32-bit version installed on different hard drive. All of these thumdrives are detected immediately and works without a problem. The 64-bit version, I have uninstalles and reinstalled readers, drivers updated for readers and controllers USB chipset, reasigning letter drive without a resolution of the problem.

  It is interesting to know that this problem only occurs with some discs that I (like Ativa 4 GB, 4 GB generic and Verbatim 4 GB). While I discovered that you can do all the nonworking day thumdrives work once if you shutdown computer and plug the thumdrive into the USB port and the computer to boot, boot time is longer than usual and when it is operational in 30 to 45 seconds drive appears in the list of devices and you can read, write and format normally without any problem to experiment. When you pull chase him and reconnect to USB port after 10 seconds same problem appears aggai. First of all, you get the message that the disk must be formatted and if you try to format you will get a message that windows cannot format the drive. If you try to access the drive, you get message that Drive is not accessible. If I take this player and plug it from 32-bit without problem, you see all the files in the drive and are able to read the writing and the format is normally.

  I'd appreciate if I am able to get an answer as a way to solve the problem.

  Pavan

  When you disconnected the battery of the laptop, you did, be sure to press and hold the power button for about 10 seconds?  This causes the rest of completely discharge power.

  This tip came in practice more than once in my experience.   ^_^

• USB 3.0 does not work on HP Pavilion 23 g010

  USB 3.0 does not work on HP Pavilion 23 g010. Can not find the driver from HP site that works. Can anyone help please because it is a new computer? Windows 8 is installed, but owner downgraded to Windows 7. I tried the drivers that are supposed to work and the said error box "this computer does not meet the minimum requirements for installing this software"... don't know what to do but would appreciate greatly any input...

  Hello:

  Your model has an AMD chipset and processor.  Therefore, the Intel chipset driver will not work.

  First, install the AMD chipset driver and restart.

  You want to download the 49.7 MB file.

  http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064

  If that does not install the USB 3.0 drivers (see the file they are included), then download and install both of these drivers and USB 3.0 will work for sure in this way.

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5359417&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_123787_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5359417&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D%257CswItem%253Dob_118744_1%257CswEnvOID%253D4058%257CitemLocale%253D%257CswLang%253D%257Cmode%253D%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  If there is any other drivers you need for this model, please let me know.

• I installed Windows XP on my new computer (with Windows 7 PRO), but my USB does not work on Windows XP. It works fine on Windows 7

  I installed Windows XP on my new computer (with Windows 7 PRO), but my USB does not work on Windows XP. It works fine on Windows 7.

  Hello

  And much more: (XP mode requires professional, Ultimate or Enterprise).
  

  Get all the benefits of Windows 7 and continue to take advantage of your investments and more
  business and productivity programs that require a PC running Windows XP.

  Note: Windows XP Mode requires a download.
  http://www.Microsoft.com/Windows/Windows-7/features/Windows-XP-mode.aspx

  Windows XP mode
  http://www.Microsoft.com/Windows/Virtual-PC/Download.aspx

  Windows XP Mode is supported through Technet

  TechNet - Forums - Windows 7 virtualization
  http://social.technet.Microsoft.com/forums/en/w7itprovirt/threads

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• my support of modem usb, USB 1.1, but it does not work on windows 7 to the motherboard desktop h61

  my support of modem usb, USB 1.1, but it does not work on windows 7 to the card mother h61 with duel core 2nd computer office prossesor genration

  If your USB modem is provided by your ISP, check for an Ethernet RJ45 port. If the modem doesn't, connect a RJ45 connection between the modem and the computer cable and UNPLUG the USB cable. Your computer should now connect to the Internet without any problem...

• Jet 7 Tablet 5709: HP Jet 7 touch screen does not work in Windows even if it works in the BIOS menu advanced starup

  Less than two months ago, I upgraded my HP Jet Windows 7 to 10. Over time some questions popped up (random apps that could not be opened, etc.) so I decided to do a full reset, deleting the files from the user. Once the 'install' process is complete he brought me to the initial configuration for Windows 10 screen, asking me my keyboard and language preference. He would not accept any contact entry. I rebooted it and he went to the advanced configuration where I could use the touch screen to do a complete reset. That has not changed anything. I found the info on the HP website and did a reset of the BIOS. That has not changed anything. I got an OTG cable, but was not able to get a keyboard work. I did, however, get a mouse works and has managed to create a new user and login. However, the touchscreen does not work in Windows. I was able to get into the settings and looked at the Device Manager settings. There was only a mouse driver listed under Human Interface. I also noticed a number of question marks in the subtopic of the processor drivers.

  I was able to use the OTG cable to try to re - install Windows 10 from a USB key. When a similar initial settings (language, keyboard) screen broke, I couldn't use the touchscreen. Later, I created a USB with Windows 8.1 thinking he might have a better chance. The same problem. He does not touch inputs. And with a key USB installed via the OTG cable, I can't launch a mouse at the same time.

  It is strange that I have not the problem in the BIOS or advanced startup options. It seems that there is a corruption somewhere, but how do I fix?

  Hello Moronihah,

  You did a clean install (delete all files and programs) the 2nd time you reinstalled Windows 10?

  That's what you need to do first.

  Then, you have to go to the HP website and install the drivers on your USB.

  Above all, you need to include the Goodix Touch Controller Driver and pilot, allowing Malta G-Sensor.

  HP Software and Driver Downloads

  You're using a hub 4 ports with your OTG cable? Which will allow you to use the mouse, the keyboard and the entire USB drive.

  

• Qosmio G30 - Media center remote control does not work in windows

  Dear all,

  I have a Qosmio G30-194,
  first I had a problem with VGA, send it for repair, when she comes back, I noticed that the remote does not work on windows Media Center, while that in A / mode V work perfectly.

  I tried a full system recovery DVD restore, but nothing has changed, even, I installed Windows Vista with all its pilots.
  Nothing has changed too, I borrowed a USB IR received for another remote that it worked perfectly with my remote on windows.

  Please advise me what to do, should I send it to the service center, or there is an easier solution.

  Mazen h
  NB:,: my laptop info are:

  PQG32E-01P018AR model number

  Thanks in advance

  Hello

  > first of all, I had a problem with VGA, send it for repair, when she comes back, I noticed that the remote does not work on windows Media Center, while that in A / mode V work perfectly.

  If you had a problem with the VGA chip then the whole motherboard has been replaced.
  Maybe it has something to do with your problem.

  Anyway, as far as I know you don t need any special drivers if you want to use the MCE Remote control. For the use of the remote control with Qosmio player you need to connect a USB infrared.

• U2413 SD card reader does not work with Windows 8.1

  My SD card reader does not work with Windows 8.1. There is no problem with the USB ports. Anyone else with problems?

  I have the same problem here too.

  The driver above does not work.

  

• lovely better does not work with windows vista home Premium what another program removes LSO and HOW to prevent the trackers?

  Question
  better privacy does not work with windows vista home Premium that another program removes LSO and HOW to prevent the trackers? Edit
  Details

  In current versions of Flash you can also do this via the control panel.

  • Control Panel > Flash Player, click on remove and erase data

• Touch screen does not work in Windows XP - Portege 3505

  Hey

  Anyone know why the touch screen on my portege 3505 does not work in windows xp?

  A lot of cheers

  Steve

  and no one knows what you have done or installed on your laptop?

  Sorry about that, but who need to know that? Have you changed something on your laptop >
  Did you install a new OS? Have you used the Toshiba recovery image?

• Satellite A505-s6970: Toshiba Service Station does not work on Windows 7

  Hey guys I need your help,

  I installed windows 7 ultimate on my toshiba Satellite A505 s6970 and I downloaded all the drivers from http://www.csd.toshiba.com/ and I installed all.

  When I open the Device Manager, 3 devices are not installed (Base-2 system device / / 1-Unknown device).
  Then I installed toshiba service station (Windows Vista / 7 32-64 bit because my windows is 64) it will search for and automatically download all necessary devices, but it does not work on windows 7, it worked perfectly in windows vista.

  Also the eco utility does not work, and the media touch buttons work just fine, but without giving that voice tone.

  Thanks for your help

  Hello

  To be honest I have no experience with this tool.
  I m using Tempro.

  However, I guess that Toshiba service station was not tested and not designed for Win 7 at the moment.
  You may need to wait for the next update that works correctly with Windows 7.

  You must understand that the Windows 7 drivers have been released in Beta version, it would mean that the final version would be released in the near future
  In my opinion, you should take a look from time to time on the Toshiba page we.
  I noticed that each new day pilot is released and released.

• 1670 CDS satellite - modem does not work on Windows 2000

  Hi-

  I removed the Toshiba W98SE and installed Win 2000 (new installation). I managed to put it on the audio driver using downloads on your website (and it works).

  I do a test on the dial installation upward and that you have installed the modem also since your website (Conexant Soft K56 Data, Fax PCI Modem). This is intended for W98SE but microsoft message is

  The port looks ok. Please advise - is it the right driver?

  Thank you.

  A Windows 98 driver does not work on Windows 2000. Therefore, you need a new driver for Windows 2000.

  I have checked the Toshiba site but your model no available Windows 2000 driver exists.
  I think you have to search the site of the factory of the modem. Maybe you can find a driver or another portable model that has the same modem.

  Good luck!

• Bluetooth does not work on Windows in Satellite C660-A047

  Hello everyone,

  I have a problem with my laptop (satellite c660-A047) Bluetooth does not work on windows (7 and 8), but it works very well under Linux (Ubuntu, Fedora, Backtrack).

  I have an outgoing method :) to do run on windows, start Linux Live then set the Bluetooth adapter to the off State, and then reboot (do not stop, restart only), and then start windows this time this Bluetooth adapter works great and updated automatically in the Device Manager.

  To use Bluetooth on windows I have to do the same steps: (.)

  If someone wants to know all the details to help me solve these curious case, I will be grateful.

  Thanks, looking forward to hearing from you soon.

  The laptop supports Wlan Atheros / module combo BT.
  This means that a single module shares WiFi and BT connectivity.

  Using Win 7 you must add the additional drivers called filter for driver Atheros BT package.
  So first the Atheros WLan driver must be installed, secondly Atheros BT filter after battery Toshiba BT.

  To help to win 8, you must install two components of driver manually to enable the Bluetooth feature: System Toshiba + Atheros Bluetooth driver driver filter
  [Turn on the Bluetooth feature after a clean install of Windows 8 | http://aps2.toshiba-tro.de/kb0/TSB2C03FI0001R04.htm]

• Satellite A210 (PSAEG) - Microphone does not work on Windows 7 64 bit

  Hello, the microphone does not work on windows 7 64-bit, the driver that I use is 64-bit Windows Vsta. The volume is implemented maximum and so is the amplification but no way to make it work with the software assistant camera Skype or toshiba.
  Can someone help me?

  Thank you

  Hi Largo09,

  Usually, you need to install the webcam driver and sound to get the microphone working. The microphone is a part of webcam

  As you wrote, Satellite A210 is not Windows 7 64 bit supported, so the only option you have the Vista 64 bit drivers

  In my opinion, you should check if the Microphone is turned on in Windows audio settings. There you can also activate the Microphone Amplifier, which can increase the volume of the microphone.

• Qosmio F50-126 - Subwoofer does not work in Windows 7

  My subwoofer does not work in Windows 7.
  I installed the audio driver Dolby Digital... Basically controls the bass.

  That didn't activate it because I don't think the pulse of air, that I used to get under Vista. What driver am I missin?

  I don't have this model laptop but it will be interesting to know if you have that you compared the sound settings in Vista and Win7?
  Can you change anything to make box works properly?

  AFAIK there is no special driver for subwoofer features.