Ho envy 5646: turns off Hp envy 5646

Similar Questions

• ENVY 15: Turn off Adaptive display for ca mode

  Hello

  I'm in the curiosity of how I can turn off Adaptive brightness for the external mode display.

  http://i.imgur.com/nnDnd9Y.jpg

  I already turned off in Power Options in Control Panel. Initially, it wasn't only to turn off Adaptive brightness so I also disabled display Power Saving Technology for battery operation of the Intel Graphics Control Panel.

  It works like a charm for Adaptive functioning on battery power but display is always active when the external power and I couldn't find an option to turn off in Intel Graphics Control Panel, there is no display of techniques for saving power for external power.

  http://i.imgur.com/WtLe6kB.jpg

  So, how can I stop the Adaptive brightness for current alternative before going blind in the sudden brightness changes when I am plugged into the wall?

  Any help is appreciated.

  Thank you!

  Hi @yldzanl ,

  Thank you for visiting the Forums HP's Support and welcome. I looked in your question about your HP ENVY 15 laptop and wanted to turn down the brightness in AC mode. On your first page it shows you in editing parameters. You will notice that the brightness level, one for battery mode and the other for the AC adapter / CC, they are not the same.

  Change this to be the same for the battery and save the settings.

  Thank you should take care of it.

  Thank you.

• HP ENVY m4-1015dx Notebook PC: hp envy m4 battery not charging but fresh when the laptop is turned off

  Hello!

  I was with my hp envy m4 core i7 for quite a while now... recently, I formatted and installed windows 8.1 64-bit installed. I decided to download some drivers from the hp site and I realized I needed to provide my model of laptop model number I could not remember so I decided to remove the battery while the computer is still connected to the power for the number, then I went back to the battery. the latter, I realized that the cell had not accused beyond of 7%, which was the level of support, until I removed the battery and when I checked the charge level, it indicated that it was plugged in but does not support. When I tried to repeat the entire process as well as close the laptop, remove the battery and turning it again nothing work and completely refusing to charge for its on.when I decided to turn off completely and then it was off it perfectly complete accused 100% operating battery estimated more than six hours of charge time, guys help me to understand what might have developed and what will be the best solution.

  Hi @Phanz,

  Thank you for your inquiry.

  I entered which you have tried to download the driver on the HP website for your laptop but realized you need the model number.  You have removed the battery while the laptop is running.  Now when you reinstall the battery, it shows that it is connected but does not charge and continues to 7%.   You have repeated the process and close Notepad and removed and reinstalled battery, but there was no change. If you turn off it charges the battery to 100%.

  You did all your Windows updates?

  Have you tried the troubleshooter in Windows?

  First of all, I would like to try a Windows restore to before remove you the battery.

  HP computers - using the Microsoft System Restore (Windows 8)

  If restore doesn't work or is not possible, you could try a Refresh Your PC to solve problems (Windows 8).

  Then you can try the following steps.

  HP laptops - test and calibrate the battery (Windows 8)

  The battery method compatible ACPI Microsoft control is basically the driver that communicates between the computer and the battery. There is a chance that it became corrupt and bad reads the battery level.

  Step 1. Go to the Device Manager
  Step 2. Select the stacks
  Step 3. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 4. Click on uninstall
  Step 5. At the command prompt, put a checkmark in the box to remove the current driver
  Step 6. Shut down the computer

  Step 7: Remove the battery for a minute and then put new
  
  When the computer returns to the top it should automatically find the driver.
  
  Step 8. Go to the Device Manager
  Step 9. Select the stacks
  Step 10. Click with the right button on the "Microsoft compatible battery ACPI Control method" which is in the list
  Step 11. Click "automatically search for an updated driver.

  Do the same thing with embedded controller compatible ACPI Microsoft.

  Last option is to reinstall your Windows 8.1 Pro.

  Good luck!

• HP ENVY 4520 all-in-one: HP ENVY all-in-one 4520 can't turn off

  I can't turn off my printer, it enters mode "Eve" only.  I press the power button, it comes to life, tap again and ensure that as soon as the switch mode.  Any help would be appreciated.

  Hi @Freckles60,

  Welcome to the Forums of HP Support! I see that you have problems with putting off the printer. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  Do a hard reset of the printer.
  Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  Reconnect the power cable to the output of the printer and the wall, and not a surge protector.
  This ensures that the printer is full on and can help this situation.

  I would say for updating the firmware of the printer, to see if that can help, printer All - in - One HP ENVY 4520

  Select your operating system.

  How is the printer connected?

  What operating system do you use? How to find the Windows Edition and the Version on your computer.

  Please let me know the result and if there is anything else I can help you. Thank you.

• ENVY 15-k008ne Notebook PC: my laptop does not completely turn off

  Hello

  When I have shutdown/Hibernate / standby my laptop, it will turn off completely.

  All programs will be closed (when stop or restart) and I think that OS will also close. But the laptop will not turn off. Power LIGHT and fan will stay on.

  And when I try to Hibernate, everything is ok, but I have the same problem.

  Whenever I have to turn it off by holding the power button, otherwise the battery will be discharged.

  After manual turn off, when I turn it on again, everything works correctly:

  -If hibernation: OS will continue to last situation.

  -If stop: OS works normally without error or warning.

  After sleep, OS works from the beginning. Because the data stored in RAM and will be deleted after power off.

  Perhaps a portable automatic perevent equipment turned off. All the drivers are up to date.

  Is there a parameter/software to check and fix my problem?

  Thank you

  Hello

  Try the following.

  Open settings and select System.  Select food and sleep, and then click additional power settings - in the next window, click on "Choose what the power button" in the left pane.

  In the next window, click on "Change settings that are currently unavailable" (close), then Remove the check mark from the box against 'Turn on a quick start (recommended) '.  Click on the button Save the settings, and then close the open windows and restart the laptop.

  When windows has reloaded, download the driver directly from Intel IMEI on the following link, unzip the and run the installer.

  https://Downloadcenter.Intel.com/download/26127/Intel-management-engine-consumer-driver-for-Intel-nu...

  Once the installation is complete, restart the laptop.

  When the machine rebooted, re - activate the quick start and restart the computer once more - let Windows take over completely for a few minutes before checking.

  Kind regards

  DP - K

• envy dv7: how to turn off "Windows defender"?

  How can I turn off "Windows defender"?

  Hello Steve,.

  Welcome! Thanks for posting in the HP Support forum.

  Usually, if you install the 3rd AV software part (for example, Kaspersky, Norton, McAfee, Tredn Micro...) it allows to disable Windows Defender. However you can do it manually.

  Several options are described here

  > > http://www.tenforums.com/tutorials/5918-windows-defender-turn-off-windows-10-a.html

  and here > > http://www.howtogeek.com/howto/15788/how-to-uninstall-disable-and-remove-windows-defender.-also-how-turn-it-off/

  I hope this helps.

• Example: ENVY, M7K39AV: my 1 month old FANCY turns off

  Turns off intermittently. It's as if I clicked on "restart". Stop then comes right back to my boot password. VERY intermittent. Contacted HP. They Reset some BIOS seemed ok for about 4 days. Now it all started. Help! Please?

  A question like this is usually hardware related. Call HP again.

• HP ENVY Notebook m6: Airplane Mode turned off my internet connection. How can I stop this from happening?

  Airplane mode resumed my internet for several weeks, then stopped working.  No internet service.  Said the repair man when the airplane mode takes longer, sometimes internet service cannot be restored.  Why is-mode plane capable of replacing my internet service?   How can I avoid this?

  Hi there @Carolyn42,

  Thank you for visiting the Forums HP's Support and welcome! I read your message on the HP Support Forums and see that you are having problems with the airplane Mode. You mentioned that the phone automatically goes into airplane Mode.

  I'd be happy to help you. If none of the steps I provide in this post help you solve the problem, please indicate this post as one acceptable Solution to another with the same question can find the solution.

  I found a document for you called airplane Mode a Forums Post on the Microsoft Community website called Airplane Mode will not turn off - WiFi will not start-up. TracyDillon on the post on the Forum said, "I have a button wifi real on top of the right side of the keyboard after F12, I pressed on that and off airplane mode and then allowed me to turn on the wifi (I did it manually)." And I'm on! "

  Here is another post from the Microsoft Community Website. This one is called hp wireless button mode "change airplane".

  After restarting the laptop you should not have flight Mode more.

  Please re-post with your model number (How can I find my model number or product number?) If you need help, and I'd be happy of this issue of research for you more far. Please show your appreciation by clicking on the thumbs up button.

  Thank you for posting!

  Have a great day!

• K010 ENVY: my laptop will not turn off

  Hello

  When I shutdown/hibernate/standby/resume my laptop, it will die completely.

  All programs will be closed (when stop or restart) and I think that OS will also close. But the laptop will not turn off. Power LIGHT and fan will stay on.

  And when I try to Hibernate, everything is ok, but I have the same problem.

  Whenever I have to turn it off by holding the power button, otherwise the battery will be discharged.

  After manual turn off, when I turn it on again, everything works correctly:

  -If hibernation: OS will continue to last situation.

  -If start/stop: OS works normally without error or warning.

  After sleep, OS works from the beginning. Because the data stored in RAM and will be deleted after power off.

  Perhaps a portable automatic perevent equipment turned off. All the drivers are up to date.

  Is there a parameter/software to check and fix my problem?

  Thank you

  Hello

  You are welcome

  On some machines, the pilot for 11 series IMEI has been known to cause that kind of question of the judgment, so it may be worth trying an earlier version.

  You can use the following method to install an earlier version of the driver IMEI.

  Download driver IMEI on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66228.exe

  Disable your wireless card (should be f12 ).

  Open your download folder and run the installer - it warns you that it is an earlier version, but simply continue.

  When finished, restart the laptop.

  If the computer shuts down correctly, turn on your wireless adapter and use the utility on the following link to prevent Windows 10 to update automatically the driver IMEI again.

  https://support.Microsoft.com/en-GB/KB/3073930

  Kind regards

  DP - K

• Envy laptop: my notebook of envy not turn off when I stopped in Windows 10?

  Hi all

  I tried everything to get my HP laptop work properly.  I am a computer programmer and my laptop not stop using the power HP power and sleep, using Windows 10.  I have to update the display driver, I tried different settings in the HP power settings and still no luck.  I have never seen anything like this before.  All my drivers are updated etc.  I'm about to give this thing!  When I select my phone stop Windows 10, should close and doesn't have the power button / light on.  When I try to go back on my laptop, it is dead and I hold the power button for about a minute before it turns off so I can restart the laptop?

  Thank you

  Mark

  Hi Mark,

  You've already tried this, but if not, it's definitely worth it.

  On some machines, the pilot for 11 series IMEI has been known to cause that kind of question of the judgment, so it may be worth trying an earlier version.

  You can use the following method to install an earlier version of the driver IMEI.

  Download driver IMEI on the link below and save it in your downloads folder.

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66228.exe

  Disable your wireless card (should be f12 ).

  Open your download folder and run the installer - it warns you that it is an earlier version, but simply continue.

  When finished, restart the laptop.

  If the computer shuts down correctly, turn on your wireless adapter and use the utility on the following link to prevent Windows 10 to update automatically the driver IMEI again.

  https://support.Microsoft.com/en-GB/KB/3073930

  Kind regards

  DP - K

• 810-160 Phoenix envy: turn off the lights inside the PC

  This computer will turn bright red. How do you turn off the infernal red lights inside the PC?

  Hello @onesa,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post on how the computer turns bright red as part of the aesthetics of your desktop computer chassis, and you want to turn it off. I'd love to help you!

  To find out what chassis PIN to remove the motherboard of your system (which should turn off the red lights), contact our technical support 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope this helps!

  Concerning

• turn off the ringer on the envy 7640

  I'm a new 7640 attached to a 2013 end Yosemite running iMac. My wife works from home and I would not have the ringtone on the sound off printer when a call comes in. Is it possible to turn off the ringer, as you can do on a phone?

  Hi @Neilkn,

  Welcome to the Forums of HP Support! I read your post and see that you want to turn off the ringer on the printer. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  I've provided the steps to disable the volume of faxes. Hope that helps.

  • On the printer, go to Fax settings.
  • Select the Fax Volume.
  • Select disabled.

  If there is anything else I can help you, let me know. Thank you.

• HP Envy 4500: New HP Envy 4500 is turn off Wifi for whole House

  The rest of my family can not use Wifi in the House when I have my printer.  When the printer is connected to the Wifi, the only thing that my family can see on their devices is the printer (not my NetGear Wifi).  When finished with my printer I have to turn off and put the Wifi for anyone to see him again.  How can I fix this.

  Hello jbitsko,

  Have you tried to disable wireless directly on the printer? My thought is that this feature is set by default to the 'go to' network when it is active on these devices. It is my first thought anyway, used to seeing injured. To disable live wireless, do the following on Page 56 of the User Guide: the User Guide, in the opposite direction.

  Follow-up of the results.

• Omen of HP: How to turn off the backlight of omen of HP

  How do I:

  1 turn off the backlight of this PC?  In the HP Envy, all I do is hit the sixth backlight the key "esc" key) but it does not work on Omen?

  2. How can I change the red light by default with another color?

  Thank you

  @Okenwa

  To toggle the backlight by pressing the FN key and pressing F5.

  To change the colors, you must use the control of harbinger of HP. The document how to use below.

  With the help of HP OMEN Control software to customize the game on laptops HP Omen 15 keyboard

  http://support.HP.com/us-en/document/c04492013

  Let us know if that answers your questions.

• Want TO M9X67AV: The screen turns off, the computer remains on

  My screen seems to have a loose fitting. It turns off when it is tilted back. Just a slight pressure to the back of it turns on again, and then turns off. I tilt it forward to keep it on. The computer stays on, just the screen turns white.

  Hi @HPEnvyuser1,

  Thank you for visiting the HP Forums!

  You have come to the right place to ask questions, find solutions and get help from others in the community!

  You said that your 17 Notebook t-n100 HP ENVY is having problems with the connections of LCD screen. Here a link to your manual page, 19 for service check the connections of the display screen.

  If you are in warranty, please call us.

  Please get back to me how that happens.

  You can say thank you easily by clicking on the Thumbs Up below!

  Thank you.