Home wireless network users can no longer connect to the internet via router, but can connect to the network

Similar Questions

• Recently installed vista update. I can no longer connect to my home wireless network.

  Recently installed vista update.  I can no longer connect to my home wireless network.  I get a message that says 'wireless link failed because windows did not receive response from the access point or wireless router.  I troubleshott he said of computing could be from low signal strength and yet it shows the strength of 100%.  Anyone have any ideas?

  Hello

  Check the firewall it is maybe it has been reset.

  In general.

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Home wireless network communication problems

  I can't connect with my other computer on my home wireless network. I don't see the other computer files, on my computer, I could before. I could see them before and I could save the files/folders from one computer to another, but suddnely stopped this from happening.

  I have Windows XP Home Edition

  Hello

  Maybe this can help.

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq#trusted

  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040
  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP -http://support.microsoft.com/kb/875357

  In Win XP pro you can visually see the setting of authorization/security and configure them according to your preferences.

  http://www.Microsoft.com/windowsxp/using/security/learnmore/AccessControl.mspx#securityTab

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  
  

• problem with express mini pci wireless lan card. I can't connect to internet via wifi but I can connect to the internet via cable.

  Hello! I have a problem with my card express 11 b/g/n wireless lan mini pci because I can't connect to internet via wifi but I can connect to the internet via cable. whenever I try to connect it repeat to myself that there is a problem with your wireless network card. I tried troubleshooting, uninstall and reinstall the program, but always the same result. I'm updating too but still the same thing. I use a windows 7 Professional on my Lenovo 412. can someone help me? Thank you!

  Hello

  Method 1: I suggest you to follow the instructions of the link to solve the problem of network card:

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems

  Method 2: Troubleshoot wired and wireless in Windows network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Reference: http://forums.lenovo.com/t5/R-and-L-Series-ThinkPad-Laptops/L412-Wireless-Automatically-Disables/td-p/264447

  You can also post your question in the forum of Lenovo to get help:

  http://forums.Lenovo.com/

• I have a home wireless network that is not safe. Need step by step instructions on how to secure.

  I have a home wireless network which is not safe, the instructions need step by step how to secure.

  Password protect to avoid any other login.

  http://www.ehow.com/how_5043404_password-protect-wireless-router.html

• I have a user who no longer works for the company.  Someone took his place, the same computer.  She used the same account as the former user.  I would like to delete the old user and assign the new.  It will lose something if I do this?  I shouldn't

  I have a user who no longer works for the company.  Someone took his place, the same computer.  She used the same account as the former user.  I would like to delete the old user and assign the new.  It will lose something if I do this?  I wouldn't reinstall anything, right?

  Hi Greg,.

  You won't lose any application on the computer.

  You can remove a user from the license and assign it to another user according to the help below document:

  Using creative cloud | Manage your creative cloud to the membership of the teams

  Kind regards

  Sheena

• Home wireless network connections cut - a router issue?

  I have 2 PC:

  1 desktop running XP (SP3) on a H61DE/S3 Asrock mobo and Intel G620 2.6ghz CPU. RAM = 2 x 2 GB.
  2. laptop running Windows 7 + Intel i3 CPU
  3 wireless router D-Link DSL-2680 =
  The office is directly connected to the router via an ethernet cable wireless.
  I created a wireless network which consists of my office and cell phones with the help of a USB and the XP Wizard on my desk. I then clicked on "Network Setup Wizard" in the Control Panel on my desktop (XP) and created the network connections.
  When I boot-up the two machines, I can see and access the connections network of desktop and laptop.
  HOWEVER, if I let the machines for a while and then come back, although I can see the icon for "DESKTOP" in my network places on my laptop, when I click the icon, the cursor looks like this market, but then an error window appears stating that it cannot find the device and I want to diagnose the connection. When I click YES, sometimes, it detects the OFFICE and sometimes it doesn't.
  The same thing happens on the desktop when I click on the "PORTABLE computer" icon in "My Network places".
  The strange thing is, when I try to connect via Start Menu / run / \\'IP address on the laptop or desktop, I can connect usually either to the PC.
  The questions are
  1 can you explain why I should b affected by these connection question - is this a problem of compatibility between window7 and XP?
  2. what type of home network, maintained by the router or directly between the laptop and desktop computer without involving the router?
  Thank you

  I assume that the HOMEDESKTOP, in this case, XP is the master browser because it is physically connected to the router and it is this machine that I created the wireless network and local.

  N ° master of domain is chosen in an election.  All devices have an equal chance of being elected little matter how they are connected. (A domain controller can always win, but that's neither here nor there).  The problem here is that the Win 7 machine doesn't listen to the broadcasts and therefore think that it is the only device on the network and therefore chooses himself as master of go.  The XP machine is involved in a normal election except that the Win 7 machine does not participate because he is not listening.  They both choose and for a while, you have two masters to browse.  The only listening to computer (XP) finally gets tired of hearing machine Win7 and abandoned as a master browser.  Win 7 becomes the only browser then, but it does not work because he doesn't listen to any computer on the network.  You can check this by bringing a window prompt (start-> Run-> "cmd") and enter the command:
  nbtstat - a HOMEDESKTOP
  or
  nbtstat - a ROMANLAP1-PC
  If the targen computer thinks that he is a master of travel, you will see a line "__MSBROWSE__".

  For some reason, keeping the folders "My Documents" opened on both machines maintained the connection for 15 hours that day.

  Anyway that you can keep the active connection, the machines will partner with the other.  Once a connection is idling, then it must re-establish contact and is when the master browser or a response of diffusion is necessary and the Win 7 machine is unresponsive.

  Try following all the steps in the article according to which apply to your configuration:

  "Networking of computers running different Versions of Windows"
    <>http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows >

  I don't think there is a firewall in itself, but the way Windows 7 manages 'Home' vs networks 'Public' that can do behave like a firewall and cause problems with firewall-like. Article states that ' the network location is a setting that allows Windows to automatically adjust security and other settings according to the type of network to which the computer is connected. "  --they don't talk a firewall, but this is part of what makes a firewall...

  HTH,
  JW

• Laptop will not connect to my home wireless network

  I've had my laptop for a few months and my home network wireless also. My laptop has always worked perfectly until last night, I was in the living room and my phone cut because it ran out of battery. I went to restart, and when I did, NO network could be found, and several others usually appear outside my home network. The wireless switch is turned on and I rebooted the computer several times, I ran the wizards and shooters of boredom, I started the wireless zero configuration, but nothing happens. everything he says is "wireless networks could not be found", and when I click on the message, a black box appears with a message saying "windows has encountered an illegal instruction. I don't know what to do. my laptop model is a Sony Vaio, but that's what I know. My ipod connects to the wireless perfectly, so I know its my laptop that needs fixing.

  Hello

  Maybe this can help, http://www.ezlan.net/wireless.html

• Windows 7 does not recognize that I am connected to my home wireless network.

  I've recently updated my desktop and my laptop at home for Win 7. I'm trying to set up a home network, but on my laptop, I can't change my home network location. Even though my laptop is connected to the internet via my wireless router, Windows don't think that I'm connected to a network. When I click on "connect to a network", it shows that I am connected to my wireless router. When I try to set up a home network on the laptop, it tells me I need to change the network location of the Public at home, but since he did not think that I am connected, it will not allow to do me this.  I searched the internet and worked through it for hours, but can't seem to find a solution to this problem.

  http://social.answers.Microsoft.com/forums/en-us/w7network/threads

  Windows 7: to connect to the Internet, a group home and by e-mail at the link above.
  

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Home wireless network connection problems

  What should I do if I normally connect to the wireless network does not appear?  It is not a network card problem, because I can connect to other wireless and school and other places.  I tried to reset the router, ping and by unplugging and seeing what I could understand on the computer at home, but nothing does.  Any ideas or suggestions would be greatly appreciated.

  Thank you.

  Hello

  Have you tried other computers to connect to your router? You use both wire and wireless
  connection?

  Unplug the modem and Router 3 + minutes. And then reconnect the modem - when it is running
  Plug in the router - when it is running - restart the computer. This is known as a hard reset.

  Check with your router manufacturer support.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

• Win 7 does not recognize that I am connected to my home wireless network.

  Recently, I upgraded my desktop and my laptop at home to Win 7. I'm trying to set up a home network, but on my laptop, I can't change my home network location. Even though my laptop is connected to the internet via my wireless router, Windows don't think that I'm connected to a network. When I click on "connect to a network", it shows that I am connected to my wireless router. When I try to set up a home network on the laptop, it tells me I need to change the network location of the Public at home, but since he did not think that I am connected, it will not allow to do me this.  I searched the internet and worked through it for hours, but can't seem to find a solution to this problem. Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  I had this same problem.  I have a home group on my desktop running win 7 64 bit.  My laptop (win 7 64 bit) could not connect because the internet connection was showing pubic hair and I couldn't change it.  Here's what I did.  I deleted all my networks and groups off the laptop computer.  I restarted my laptop.  On my desktop, I went into Control Panel, home group and consulted my password.  I also need my wep key of wireless network.

  To better understand, my wireless network name is cleopatraiz

  On my laptop, I went into the wireless network connections through the status bar at the bottom right which displays all networks wireless scope.  I clicked on my wireless (cleopatraiz) and it prompted for the wep key.  I entered that and then I went into newwork & Sharing Center, was now showing my active network as cleopatriz, I clicked on choose home group and sharing options and joined using my password of the Group House of desktop computers.  It worked.

• Pavilion Elite e9290f: need to connect to a home wireless network

  We had bought our PC for several years and had it connected to a router to access the internet.  I think that the computer has the feature to connect to a wireless network, but you should never use this feature.  We moved recently, and now we are in a situation where we are unable to connect the PC to the router.   I'm not sure how to proceed.  I don't see that a WLAN listed in Device Manager.  We are running windows 10.  any guidance would be appreciated.

  Kaalee75, welcome to the forum.

  The computer has a wireless interface card:

  Figure: Wireless card - side view (version embedded antenna

• FOJ 8500 909 g will not fully install, not accessible from the computers in home wireless network

  I bought an Officejet Pro 8500 909 g which worked well on our home network for 18 months.  Desktop is 32-bit Windows 7 with a USB cable.  Two wireless devices are 64-bit Windows 7.  Printer suddenly has not recognized the cartridges and frozen with the message "problem with the ink cartridge.  Called HP (unassisted) and tech support of holders of the contract of service - without help.  They sent a refurbished (even) model which I can't install on USB or wireless connection completely.  Yesterday, I was able to print at least one 3 machines on the network (not every machine wireless).  Today, I can not print even the USB device.  5 days lost uninstall then reinstall the printer software, router, etc.  Connected wireless network.  Printer says it is on the wireless network.  HP Solution center is not accessible because the "printer is not completely installed. Help?

  Hi EWQuince,

  The information you have given it seems that the printer is not on the same network as the computer. If the printer was on the same network as the computer, the IP address would be 192.168.1 instead of 192.168.33. You must run the printer Wireless Setup Wizard and make sure that you connect it to a network, the computers are connected. Once you have the printer connected to the same network all your problems should be solved.

  To connect to the wireless network

   

• I'm trying to our laptop connecton to our home wireless network

  I tried to connect one of our PCs to our wireless network and continue to get the dialog box Windows network box indicating "wireless authentication failed because of a time-out" this pc had a virus on it, but has been deleted, clean and renovated.  It was plugged in and worked before why not now? He does not see the wireless network but will not connect help?

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  It will be useful.

• How to do to add a Windows XP existing home wireless network

  Existing wireless network computer is a Windows Vista laptop and I want to add a Windows XP computer using a flash drive or a CD or?

  Hi fouffana,

  See the article and check if that helps.

  Add a device or computer to a network

  http://Windows.Microsoft.com/en-us/Windows-Vista/add-a-device-or-computer-to-a-network