How can I fix com surrogate does not not under Vista?

Similar Questions

• How can I fix computer that does not start after the fan turns phase?

  I have a Compaq Presario SR5510F PC, Windows Vista Home Premium, AMD Athlon x 2. Lately, my computer is even worse at the start. When my computer starts, the fan should run for a few seconds, then it should stop and lead at the start with Compaq logo screen. But lately, the startup was completely terrible for my computer. Today, most of the time when I press the button in the box of the computer, the fan turns on and it continues to turn, and nothing comes on the screen. It isn't that rarely when the fan stops running, but then the monitor displays always upwards in white and VERY rarely when the startup screen appears, then it freezes on this screen. At this rate, my computer is totally useless when it does nothing but run his fan. This means that I can not go to boot options at all and go to the "last good configuration". What can I do to fix the computer when I can't have anything with her while she is empty?

  It sounds like a hardware problem, not a software problem.  If the computer rarely gets past the BIOS (material audit) stage of the startup sequence, then Windows is is not yet involved in the boot process again.  Request assistance from someone trained in the skills of troubleshooting hardware since this can become very expensive very quickly.

  "Maersk Custard" wrote in the new message: * e-mail address is removed from the privacy... *

  I have a Compaq Presario SR5510F PC, Windows Vista Home Premium, AMD Athlon x 2. Lately, my computer is even worse at the start. When my computer starts, the fan should run for a few seconds, then it should stop and lead at the start with Compaq logo screen. But lately, the startup was completely terrible for my computer. Today, most of the time when I press the button in the box of the computer, the fan turns on and it continues to turn, and nothing comes on the screen. It isn't that rarely when the fan stops running, but then the monitor displays always upwards in white and VERY rarely when the startup screen appears, then it freezes on this screen. At this rate, my computer is totally useless when it does nothing but run his fan. This means that I can not go to boot options at all and go to the "last good configuration". What can I do to fix the computer when I can't have anything with her while she is empty?

• How can I order i-Tunes DOES NOT close automatically after 30 minutes... Despite having put in place to save energy to stay active for 2 hours?

  i mac OSX10-9-5 2015.   How can I order i-Tunes DOES NOT close automatically after 30 minutes... Despite having put in place to save energy to stay active for 2 hours?

  To the best of my knowledge iTunes has all of the features that could stop him. What make you believe it's iTunes rather than some other power saving feature? What happens exactly 30 minutes? It's happens during playback video or audio?

  TT2

• How can I fix the problem of not being able to open files by double clicking with photoshop

  How can I fix the problem of not being able to open files with photoshop by double-clicking it in windows Explorer?

  This problem affects psd, jpg, and png files.  I get an error saying "the program can't start because adbeape.dll is missing on your computer.  I can open all these types of files in the menu 'open' in photoshop.  It is not a matter of them not having no not extensions.  I use windows 7.

  Thank you

  Thanks for the update.

  Just for test, could you please rename Photoshop.exe to Photoshop CC2015.exe location: C:\Program Files\Adobe\Adobe Photoshop CC2015

  then change the file association to the new renamed exe file and let us know if this helps or not.

• I have corrupted files as determined by SFC scan. How can I fix that SFC could not fix?

  I used a (RegZooka) registry repair tool and must have damaged some files.  At the time I discovered, RegZooka could not help me, but another suggested that I have run the System File Checker.  I did and got a newspaper that shows some of the files that it could not fix.  How can I fix them?

  Hello.

  The manufacturer's recovery disks do not normally offer the options of 'work' to do a repair Installation

  If you still have problems with files SFC cannot repair, you can borrow a DVD of visits of Microsoft from a friend of friend or work, not the manufacturer's recovery disc and try a repair installation:

  "How to perform a repair for Vista Installation"

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  See you soon.

• How can I say Migration Wizard does not use WiFi?

  I'm trying to migrate from

  an old Macbook Pro running Yosemite

  for a new Macbook El Capitan running.

  I normally connect these machines to the internet through WiFi and DHCP.

  When I tried to migrate using WiFi it is too slow.

  I tried to disable WiFi on both machines and directly

  connect using an Ethernet cable

  as the Migration Assistant suggested doc.

  I needed a lightning for Ethernet card to connect to this

  cable for the new Macbook Pro.

  So I ran the Migration Wizard on both machines.

  The Migration Wizard insisted to turn on the WiFi again.

  How can I say Migration Wizard to use the cable and not WiFi?

  I guess I have to configure something on the network first,

  but the Migration Wizard documentation does not explain how

  to do manually and does not correct it automatically.

  Connect by Ethernet or drive directly to the computer and turn off Wi - Fi.

• How can I fix error Code 800706BE on my Windows Vista?

  My computer has installed an update and I got an 800706BE error Code on my Windows Vista computer.

  How can I fix it?

  Make sure that your anti-virus is off and try again the update, if it still doesn't work, try updating in a clean boot environment:

  Test in a clean boot environment to see if the problem is related to other services or programs-

  How to troubleshoot a problem by performing a clean boot...
  http://support.Microsoft.com/kb/929135

• How can I fix PES-entry point not found?

  I have successfully installed PSE11, but can not open because of two warnings:

  (1) the procedure entry point HandleWindowFont could not be located in thePLUGIN.dll.

  

  2) .. Plugin "Topaz" is that is not designed to tun on windows or it conyains an error...

  

  I can probably fix the other by myself.

  How can I correct the first point?

  Try http://forums.adobe.com/message/4879888.

  "Topaz" plugins are fully compatible with PSE11. There is no need to uninstall. Just make sure that they are installed in the correct folder according to the instructions on the site "Topaz".

• COM Surrogate does not work on my computer. I installed all THE updates, but this still does not work. Help, please.

  I don't know what is COM Surrogate.  It lights up just on the screen and I don't know why!  He just tells me to install important updates, what I've done.

  Hi Carolina,.

  According to Alexander in this thread of TechNet:
  "COM Surrogate (dllhost.exe) is an application that is often used by Windows Explorer to isolate themselves from codecs (if explore would be the codecs in its own process, it would crash as it did in XP, so explore generates dllhost to actually treat the miniatures, etc outside its process space)."
  http://social.technet.Microsoft.com/forums/en-us/itprovistadesktopui/thread/f6630b7b-4692-46df-91bc-db10da2d1346/
  There are a few things that people have done to solve the problem.
  1. If you have Nero or Roxio Easy CD Creator installed, try to uninstall it to see if this problem is still happening.
  http://Windows.Microsoft.com/en-us/Windows-Vista/uninstall-or-change-a-program
  ' 2 ' Kiifer ' reported that checking the "Always show icons" option in folder options seems to have solved their problem.
  Click Start > click computer > press the Alt key to bring up the menu option Tools > click on options files > click the View tab > check the box for always show icons, never thumbnails. This is the first check box under files and folders.
  Please keep us updated.

• How can I fix the USB ports on work for Vista?

  I have Windows Vista basic and USB does not work for all devices when they are plugged in. I get the message "devices connected to the computer USB has malfuctioned and Windows does not. "I also noticed that in the pilot do message"No driver for this device"Port_ #001.Hub_0007 ' if plug all devices including a USB key or a mouse, goed by single power. Any ideas how hard to pull of this problem.  Thanks in advance

  You can try to go to Device Manager and uninstall all the drivers remove all listed (only the hubs and not others) cos of your terminal and restart your computer. After restarting plug your rear hub.

• Satellite X 200-15 k - how can I activate the advanced buffer HARD drive under vista?

  How can I turn on buffer advanced performance HARD drive under vista? This option is not available for this drive?

  * Check this box: *.

  1. right click on the computer in the Start Menu, then select Options.
  2. click on advanced on the left system settings.
  3 select the Hardware tab in the System Properties window.
  4. click on the Device Manager button.
  5 expand disk drives.
  6 right-click on a hard drive under disk drives, and then select Properties.
  7. Select the policies tab in the Properties window for the device.
  8. check Enable advanced performance.
  9. click OK to save the changes and reboot your computer.

  If this is not possible then the buffer of advanced performance is not possible with this HARD drive.

  Hey Buddy

• How can I resolve USB arbitration does not start error 31: a device does not work

  Any ideas how to fix or troubleshoot this error.

  I read the following thread but has not been able to post to the thread (because it was LOCKED).

  Wire 1383098 VMWare communities

  I bought a new Win7 box and VMWare Workstation 7 is installed.  It works great EXCEPT that I can't access USB devices.  To start the virtual machine, I get an error saying:

  Disabled host devices USB connections.

  The connection to the VMware USB arbitration service has failed.  Please check the status of this service in the Microsoft Management Console.

  I watched the news of C:\Windows\Temp\vmware-SYSTEM\vmware-usbarb-SYSTEM-###.log, and there is not much more than the above error.  It is shown below:

  -

  ---

  10 Nov 05:10:24.039: usbArb | Journal for VMware USB Arbitration Service pid = 3520 version = 3.0.0 build = build-203739 option = output

  10 Nov 05:10:24.039: usbArb | The process is 32-bit.

  10 Nov 05:10:24.039: usbArb | Host codepage = encoding windows-1252 = windows-1252

  10 Nov 05:10:24.039: usbArb | DICT - USER PREFERENCES C:\Windows\system32\config\systemprofile\AppData\Roaming\VMware\preferences.ini

  10 Nov 05:10:24.040: usbArb | DICT - C:\Windows\system32\config\systemprofile\AppData\Roaming\VMware\config.ini default USER

  10 Nov 05:10:24.040: usbArb | DICT - HOST by DEFAULT C:\ProgramData\VMware\VMware USB arbitration Service\config.ini

  10 Nov 05:10:24.040: usbArb | DICT - of the SITE by DEFAULT C:\ProgramData\VMware\VMware USB arbitration Service\config.ini

  05:10:24.042 nov 10: usbArb-3536. USBArb: From VMUSBArbService args: "VMUSBArbService."

  05:10:24.043 nov 10: usbArb-3536. USBArb: USBArbInit failed with the error: 31

  05:10:24.044 nov 10: usbArb-3536. USBArb: Stop service, status: 31

  -

  ---

  I looked at some of the newspapers (but there were too many pass by) to current user\AppData\Local\Temp c:\users\.  Newspapers have been named: vminst.log, vmsetup.log, vmmsi.log.  I can post them if it will help, but there are several of them and different copies under different users (admin1, user1, user2, etc.)

  I tried to manually start the USB Arbitration Service and it starts not (same simple error, error 31 above).

  I looked for a "AMD USB filter driver ' to turn it off (it worked for someone else) but not found one installed.

  My configuration is:

  Hardware: HP Pavilion Elite - AMD X 4 2.6 GHz 8Gig DDR3

  SE host: Windows 7 Home Premium, 64-bit (Build 7600) 6.1.7600

  Guest OS: Win XP Pro SP3 (but I think that the problem is not related to the guest)

  VMWare Worksation: 7.0.0 build-203739

  I like the speed of the system, but I also met problems disc cloaning (for some reason, the SATA drives are not detected by some software disk imaging).   I was able to get the ghost at work but not Acronis, Paragon or.  I think that it is a separate issue but leaving it where it is important.  In these cases, the messages indicated that the X 58 chipset (I think this is right, but I'm not positive).  He is a level too low to follow me.

  I have fought this same problem on a Vista machine.

  Try to right click on one of the USB hubs and looking at the details of the driver. If usbfilter.sys is listed open HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {36FC9E60-C465-11CF-8056-444553540000} and remove the UpperFilter, pair of usbfilter.

  I rebooted and it works fine now.

  Shad

• How can I fix my "iDRAC is not ready' problems?

  We have a PowerEdge R420 running a server VMware ESXi 5.1 in RAID mode.
   
  We had a power failure which resulted in obtaining R420 one ' SWC0700: iDRAC is not ready "error.  Our version of setting iDRAC is 1.30.30.27.  I found the report on the iDRAC reset and update the firmware of the iDRAC with this version and error state.  Following suggestions to disconnect power cables, USB cables and then keeping the power button for 15 seconds until not clearly the problem.  Boots following this process had the same error of SWC0700.

  I created an OSMA7.1 DVD boot and I tried to install, a USB drive, different versions of newer than 1.30 iDRAC, but every time that the system has reported/proc/ipmi/0 /: file not found (or something similar that I'm going on memory here).

  I needed the system upward, so I pressed F1 to continue to run.  The system seems well except that the fans turn at high speed.

  I saw another post on the button of the iDRAC for 15 seconds to reset the iDRAC, and I tried with the system in place and is functioning normally.  This did nothing for the speed of the fan, so I guess it has no effect on iDRAC.

  I installed the COnsole of Administration Dell, on the ESXi virtual machine in the hope of launching an upgrade of firmware iDRAC of this virtual machine, but I couldn't connect to vCenter, which is probably because I don't have a VCenter server, only two servers ESXi 5.1 - I think I misread the DELL site thought this could work somehow for me.

  Now, I think the performance of the ISO bootable, I found on this Web page: www.dell.com/.../SLN296511
  My fear is that something can go wrong, and I'm losing my server installation.

  If I put my confidence in the ISO bootable update?  Should I call Dell support - I am about 4 months out of warranty repair technician on-site - and plan to replace my motherboard as I read in other posts on this forum?  The motherboard can be replaced without altering my ESXi installation?

  I'm worried that runs the server with a "iDRAC is not ready" error will burn the server, or do anything else that will ruin the server.  Should I still worry about this?

  Thanks for the advice and suggestions in advance.

  The f

  It sounds like the replacement of parts is necessary. There is not a way to export the configuration of the BIOS. The fee for a replacement of tech is usually $299 for servers, plus the cost of the system board. I'm not sure what would be an extension of one year on the guarantee.

• How can I fix updates that do not update, but keep trying to update?

  5 same updates update everyday, or if it says "update successful". How updates without FRY? The updates are: KB2418241-KB983583-KB982524-KB979909-and KB982168. They are all for .NET Framework 2.0 SP2 and 3.5 SP1 except KB982168 and is for 3.5 SP1. Each of them have (x 86) at the end. It's the first time that this has happened so please forgive my ignorance. Jacob

  Error messages?

  Use them as a guide-

  When you try to install an update for .NET Framework 1.0, 1.1, 2.0, 3.0 or 3.5, you may receive Windows Update '0 x 643' error code or error code Windows install "1603".
  http://support.Microsoft.com/kb/923100

  When installing updates using Windows update or Microsoft Update you may receive error 80070643 0 x or 0 x 643
  http://support.Microsoft.com/kb/976982

  Vista
  http://Windows.Microsoft.com/en-us/Windows-Vista/Windows-Update-error-80070643

  As a guide, relocation order.

  1. the .net framework 3.5, then...
  2 .net framework 1.1, then...
  3 .net framework 1.1 SP1

  Error code: 0 x 80131700
  Error code: 0 x 643
  Error code: 0 x 80070002
  Error code: 0x66A
  Error codes above mean that you need to reinstall Framework

  1. How to determine what version of the .NET Framework is installed and determine whether the service packs have been applied
     http://support.Microsoft.com/kb/318785
     This article explains how to determine what versions of Microsoft .NET Framework installed on your computer.

  2. How to repair an existing installation of .NET Framework
     http://support.Microsoft.com/kb/306160
     You may need to repair your installation of .NET Framework, if you upgrade your operating system or if the installation of the current framework is damaged. This article explains how.

  Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• How can I fix my XP do not go to Setup boot sequence

  Somehow I messed up my boot sequence and now whenever I start, he goes to the selection of the F2 to enter setup or F1 to continue.  It seems works continue, but of course, I have an error in something.

  My windows is XP

  Anyone have a suggestion on how to restore my startup?

  Doug

  The seemingly obvious solution is to hit the F2 key to enter setup and fix everything that is bad.  The BIOS settings are closely related to the motherboard and vary a lot.  Some allow re-scan devices and then save the setting.  It seems that there is a setting in the BIOS that the system doesn't seem to like when it starts.  You just need find and fix.

  HTH,
  JW