How / change CPU fan on T41 1.7 Ghz

Similar Questions

• Doesn't let me change the Cpu fan!

  Hey guys,.

  My cpu hp craped out fan and I tried to buy another fan I removed the old an and replace now the new fan will only work 830 RPM compared to the former which took place in 1800 as soon as the computer I tired about three different fans, it seems that he wants only foxxcon fan to work right so my question is How can I change the cpu fan with a one outside the foxxcon aftermartket because I can not find the same! model is a P6000 P6741f series!

  really want your help, I won't heat my cpu!

  Thank you!!!

  Ryan. D

  Therefore, replace the fan with a new and new thermal interface materials.

  Check the time against the maximum allowed for your CPU. Temperatures 10 degrees cooler (in degrees C) thean max when you run a game requiring high graphics so stop worrying.

• Satellite A500-138 - how to change the fan speed?

  Hello

  I have a question how to I change the fan on my A500 speed?

  I mean with power of change in BIOS, I don't have the option advanced on my BIOS so I can't change that... Any ideas?

  Hello

  > I have a question how to I change the fan on my A500 speed?
  > I mean with power of change in BIOS, I don't have the option advanced on my BIOS so I can't change that... Any ideas?

  You cannot change fan speed yourself, because there is no option in the Bios. I also tried to change with utilities like a fan speed control utility. But I couldn't stand it. Perhaps, someday they will out of the Bios with support for fan speed control. :)

• CPU fan noisy in Satellite P200-17 b - how to remove dust

  My toshiba p200-17 b is now several weeks ago about 16 months old, the CPU fan works conttineously all the time.
  The air fan, I see there is a lot of dust in the CPU fan.

  What should I do now?
  Is the clean cpu fan included in the warranty?
  Is it possible to do this cleaning by myself?

  Yes, you can clean yourself.

  For this, you can use compressed air jet and could blow the dust from the fan. Should not disassemble the laptop.

  But before this, shut down your laptop.

• I have a p6310f and I have my cpu fan connected directly in my msu and fan controller how do I

  can say that the cpu fan has no error and fan service doesn't have a system soon error

  EDTII

  The fans (CPU and case) are attached to the motherboard for this (the sensors) headers. Connect directly to the power supply (not a ' SSM') bypassed motherboard sensor circuit.

• Pavilion 500-160ev: CPU fan control

  Hello.im trying to figure out how to increase the number of turns of my cpu (pwm) fan in my Desktop hp Pavilion 500-160ev. I tried to do it in the BIOS, but there is no such option. Also I updated my BIOS but I can't find anywhere where to change the fan speed, the option is obviously locked. Third-party program does not work as SpeedFan.I have almost tried everything. Any ideas?

  40 c seems quite acceptable.

  The Noctua NH - D9L has a maximum speed of 2000 rpm, minimum speed of 400 rpm

  If it is open to only 800 RPM it shows me that your system runs pretty cool.

  You can install the free programReal Temp, it will show your CPU current temp as well as distance max temp and "the thermal State.

  You can run a CPU Stress Test program to test your fan. As the program your CPU at 100%, you should see the ramp speed of the fan to the top.

  If you found my answer helpful please say thank you by clicking on the icon of the thumb.
  If my answer has solved your problem, please mark it as accepted Solution. Thank you!

• Compaq Presario CQ5110Y: Compatibility of CPU fan

  After doing a little research, I have another question regarding the change of my CPU fan.

  An article I read said that I need to check the compatibility of the new fan that I use as a replacement for my fan CPU 7 year and liked because he must blow at the same speed as the original fan; otherwise, the BIOS may not recognize the fan.

  How can I find out if the new fan specifications are the same as the old one? I already bought a 80 mm fan, but I don't know if it's the right to be placed on the radiator.

  Thank you.

  Thanks for asking this question.  The simple answer is a program called CPUIDHWMonitor.

• Error: Failure of CPU fan

  The original motherboard was not on my Pavilion a6528p. I got fed up with accidents several blue screen whenever I started to use it. Once he ran for a while (an hour or two), he has generally kept running. Worked to try to eliminate the virus/malware (multiple programs found no no), the memory test (used memtest86 +, ran all night without fault), CPU test (Prime95 torture test used, ran all night without fail) decided to try another motherboard. Not able to find a new, so decided to take a chance on a used.

  The jury used (so far) has never crashed. It is therefore a good thing. However, every startup I get the message "ERROR: CPU fan failure! Press F2 to continue to start. "I believe that this message is incorrect because I ran Prime95 torture for hours test and the temperature of the Processor reported by CPUID HW Monitor program is around 52 degrees c for each carrot. When I run Prime95 torture test, the temperature of the CPU are much lower, around of 38 degrees C.

  The HP support document http://support.hp.com/us-en/document/c00013522 describes in detail by selecting Hardware Monitor in the Advanced BIOS menu. There is no choice in the latest version of the BIOS, I installed on the HP website, which identifies as BIOS Version/Date American Megatrends Inc. 5.43, 10/09/2009.
  
  Because the help document is incorrect and no help, someone has ideas how to eliminate this message CPU Fan has failed, what happens whenever I start the computer?

  JimK Hello,
  
  Not all BIOS versions have the same settings and you're right that your BIOS is not this setting. Looking at what the settings you have (http://goo.gl/1mCvq) there is no parameter, you can change even not to ignore the message.
  
  The motherboard doesn't like not the CPU fan that is currently installed, if the fan is not mounted in quick power enough, do not provide enough cooling, or is simply not sufficiently powered is unknown, nor can it be determined. You can try to unplug the CPU fan and reconnect to ensure a solid connection. Probably, you should be able to say that the CPU fan turns so you can figure out if she has no or not enough quickly.
  
  Your options after that are to
  1. process by pressing F2 at startup to work around the error
  2. try another fan for processor to see if you can get the motherboard like.

• «the cpu fan works not.» Check the fan connections and call for service. »

  I was wondering if a failure of different from 'CPU fan has failed... system in a few seconds will stop. " I have an office of DX - 2000 P4 under XP SP3 that I just changed the motherboard and CPU fan on. All the fans are running at about the same speed. (P/S, chassis and CPU). Not very fast but cannot see the fins. Computer sat for several years. I was wondering what is the real test and how the fan speed is controlled. I suppose that temperature sensors built into the cpu, somehow, there must be a variable voltage applied to the fans to change their speed and/or a measuring device to see what is their RPM. This must be controlled by the BIOS as is any pass/fail test. My next step is to replace the old fan and see what happens. I have a new p/s to install should be here today. Actually used, but cleaned up and tested. Economy of cleanup. Not sure if my older diet could be the cause of the issue with low Volt.

  If the fan is slower than the factory fan, you will have this problem.

• Disabling the cpu fan on HP p6210f

  I recently installed a Cooler Master Hyper 212 plus, which uses a power connector 4-pin CPU fan. The HP p6210f has a Pegatron M2N78 - THE motherboard, which has a 3 - pin CPU fan power connector. The fan turns on fine, but then stops and I get a message before Windows 7 Professional can load the CPU fan has failed and the computer turns off.

  Everything I've read suggests that the new fan does not spin fast enough for the taste of the motherboard and that, given that the fan works properly, I can safely disable the CPU fan error in the system BIOS. Yet, I don't see an option for this disable in the BIOS. How can I turn off the error on a HP p6210f CPU fan?

  RoJCor wrote... "I would still be able to access my full BIOS."

  What you have is the complete HP BIOS. HP and many other features of locking of the OEM in the BIOS to prevent users from accidentally and unintentionally change the settings which becomes a service call. The only way to restore the features which have been locked, is to ask a hack or modification of one of the sites that do this kind of thing. Don't forget that the desired function may not be in the BIOS first, the BIOS can be difficult to hack or modify, or that you end up with a virus or other.

• Export of Alienware CPU Fan

  Dear community Alienware

  Intro:

  Four days ago the fateful date were to occur, my 5 year system, bitten the dust, quite literately... dust so hidden in this case. So I got a new motherboard and a new case since there was unfortunately no more.

  So I wanted to save all even remotely from my old pc, as a souvenir, and since I don't see the point of throwing things that work.

  Question:

  How can I export my alienware cpu to my new system. Unfortunately the cpu pump seems to be a 'special' alienware, and I can't seem to know all decent positions if it's important or not. Or how to reconnect somehow. my current fan is the basic intel cpu fan you get for free and it is quite wrong to say the least.

  Other data:

  All parties except for the motherboard are always available.

  New motherboard is the: msi z97Gaming 3 (yes I know, 3rd world country I am living, not really any decent other options)

  available heatpaste, the fan fits after a few changes of detail. (to the metal ring, I didn't touch the fan itself)

  at the end:

  
  Thanks in advance for any response, even if it's a soul crushing "he died mate, let her rest."

  Best regards, darkminaz

  You cannot use your alien-cooler, unless you cut the 7 pin connector, cut the wire, tie / crimp on 3 new terminals & insert correctly into a new connector for fan 3 pins:

  

  online stores pc etc.

  If you cannot do this, or someone do it for you, sell your cooler, buy a new cooler liqwid, Corsair, Antec Zalman, what you prefer. Donate your old stop, recycle, pass it as a gift or sell online, selling yard, colleague, etc.

  Your cpu is not a 1150, so it cannot go into the Z97. Sell everything you can to help him to pay the new rig...

• Intermittent operation of CPU fan

  We have a Dell Studio XPS 8100 December 2010.

  The last days, fan runs intermittently high/low to a 5s interval when the PC starts to heat.

  When we use the Speedfan introduced to manually control the behavior of the CPU fan, it does not.

  It seems so that the fan is not broken, but the CPU fan control algorithm has changed or is influenced in some way.

  Any ideas how to fix this problem without having to use the software speedfan?

  Well after looking through a hundred forums, I * think * I can found the solution.  Look in your programs to uninstall for Dell Datasafe.  You should notice it installed around the start of your problem (with the wizard of Support from Dell but I don't think that one is the problem).

  Uninstall anything that says Dell Datasafe, then restart the computer.

  I did and then I ran some graphic benchmarks to ensure that my CPU was well used.  The problem disappeared and has not returned since.

  If you uninstall Datasafe and keep Dell Support Assistant don't forget to tick boxes in Wizard help for automatic download or you can find Datasafe relocate again!

  Don't know what was Datasafe or why Dell has decided to install on my PC, but this seems to be the problem.  Good luck.

• Satellite P200 - need CPU fan replacement

  I have a Satellite P200-16V and my problem is on the cpu fan.

  I tried to open it, but after the keyboard, hard drive, Rams, OVOCHECK and 40-50 screws and some cables, I realized I have to get out the motherboard and screen mabe and I close it again after 3-4 hours. The cpu fan has been breaking and I don't know what to do.

  I am from Greece. If I go to the toshiba in Greece, I can find a cpu fan or any system cpu radiator? Can you help me?

  Hey Buddy,

  Looks like the fan needs to be replaced and therefore, you should contact the closest service provider authorized in your country. Guys can order a replacement part and swap it out.

  On the Toshiba site, you can find a list of them:
  http://EU.computers.Toshiba-Europe.com > support & downloads > find an authorized service provider

  Sorry, but everything that s what I can say. Here it s only a user forum so I think no one knows the exact number of part or a manual how to take apart the laptop but the ASP can do for you. :)

• Satellite L670 cpu fan noise

  As I sit in front of my new laptop L670, from the left end of the keyboard comes up and down a whirring frequent sound that I'm pretty sure is the CPU fan
  (not HD).
  What is too much? I find it disturbing. There is no sound from my old Toshiba 1 year. The room temperature is a constant 20degrees, so it is not overheating.
  And does so even when sitting idle with just the screen Windows7 IE no software activity going on at all.

  I'm worried that this is a faulty computer. It is old (for me) - 2 days, purchased new. Still able to resume.

  Grateful for any thoughts.

  L

  Hello

  I put t know how I can you use your laptop, but for normal use I recommend to use the balanced power plan. Enter the advanced power settings for the management of the balanced diet and open Toshiba power saver.
  You will find options for cooling method.
  Set to optimized battery.

  This should reduce the activity of fan cooling.
  Please test.

• Tecra S11 - CPU fan is high speed

  Hello

  We have a problem with nine Tecra S11 / Windows 7 64-bit. The CPU fan is noisy high speed during ignition and start Windows. No change after logon. Speed remains unchanged up to go to the sleep mode once. After waking up, everything is OK.

  For me, it seems to be a problem with the firmware (BIOS). Update V1.70 but no change. We have same problem with the S11.

  Any ideas?

  Cordially Stevep

  Hi Stevep_1,

  Have you tested different cooling options in Windows power management? Check it for each profile, and then select battery optimized cooling.

  It work?