How does them VLANS in Cisco UCS

Similar Questions

• How does them mode chapter audio books?

  If I do the mp3s of my audiobook CD and load them on my Clip 2gig (with firmware 1.01.29a), what makes "mode chapter? No matter what? Or is this only valid/good if you listen to audio books in a different format?

  Thank you!

  For Audible mode chapter will pop you through the large audible section piecewise (in my experience the chapters of the book, not just not really different points in the book to navigate more easily).

  For mp3, overdrive etc. Chapter mode allows to use buttons to jump between the fwd/rew audiobook files and will allow the number of files in the upper part of the screen.

• How to move a stand-alone series C of Cisco UCS managed service profile without losing any data?

  Hello

  We currently have a stand-alone series cisco C with 2012 Windows Server installed on the local disks.  We need to go this Cisco UCS server managed with a service profile, but can not lose existing data and the method of operating system boot.

  Does anyone know how to do this?

  Thank you

  Hi Adrien,.

  To be able to accomplish this together the local drive to 'any Configuration' policy this way UCSM won't overwrite the current raid on the server configuration.

  See the link below

  http://www.Cisco.com/c/en/us/TD/docs/unified_computing/UCS/SW/GUI/config...

  Let me know if that helps

• Reserved Vlan ID in Cisco UCS

  I understand that to be true with Cisco UCS platform:

  "you cannot create a VLAN with ID from 3968 to 4047. This VLAN ID range is reserved. »

  I have a private network 172.16.x.x North on my network is in the vlan what ID 4001, I wanted to present this southbound on NGC.  Maybe it's a stupid question but the only way to be arounf to change the Vlan ID to the one who is sitting in the pool of UCS Vlan IDS that are allowed?

  Yes, unfortunately

• How can Cisco ucs c220 m4 I start with 12g cisco sas controller? 2012 UEFI Server installation issues

  first time with cisco ucs c220 m4, check my photos

  You have a VD 11TB.

  Only way to start on this is by using UEFI.

  You need to activate UEFI in the boot order.

  Anything over 2 TB and more 4 K sector size readers require the UEFI boot option.

  BIOS will not process the VDs when manages UEFI.

  Kirk...

  Summary for those who seek a similar question:

  • Client a large VD created, 11TB
  • 2 TB and more, 4K sector drives, require boot UEFI + GPT, cannot use the legacy/MBR
  • To set startup to local HD option, that referenced the PCI-E Slot, the raid controller was in (HBA slot in this case)
  • UEFI mode, can't score a VD as "bootable disk / startup.
  • You will see not the VD/raid controller appear in the 'real' boot order during the OS install.
  • Once the installation of the OS compatible UEFI is made, it will create a UEFI boot to the operating system "Windows Boot Manager" entry in our case.
  • After the next reboot, if you check your boot order, you should see this UEFI OS boot manager entry.

• Configuring the Cisco UCS 5108 ports

  Hi all

  I'm new in the world of the Cisco UCS server and am setting up Cisco UCS 5108 blade server. The server has two Cisco UCS 6324 interconnections fabric I did the initial Setup on and I try to configure the ports for the blades. Looking through the various articles and tutorials after setting global policies, I see the whole world establishment of uplink and server ports. What I read the uplink ports are plugged directly into the switches (I work with two cisco nexus switches), and server ports are used to connect to the chassis.

  I wonder once the configured ports server what exactly are supposed to connect to? I assumed they would also connect to the switch nexus with the uplink ports. However, every time I set up the server ports and plug them in, the switch doesn't seem to have flooded and we lose all connectivity. If I unplug, the connection is restored almost immediately.

  The current configuration, that I work with is two ports uplink on each fabric interconnect (4 2 total in each switch of nexus), two server ports on each (4 2 total, in every nexus switch). The only other element connected to the nexus switches is a SAINT who will be configured as a boot and storage of the UCS 5108.

  Looks like you have a Mini UCS (6324), with 4-port 10 GB (each FI/IOM) with port QSFP 40 GB that can provide network connectivity linking rising, or if configured as a server port, could be used to connect to a server in a rack compatible Cisco UCS, or connect to a 5108 additional with IOM 2204XP chassis.  The blades installed in your initial 5108 chassis 6324 FI/IOM of housing have internal connectivity to the FIs / IOM without the need to configure ports 'server'...

  Please take a look at some of the visuals in the datasheet below.

  http://www.Cisco.com/c/en/us/products/collateral/servers-unified-computing/UCS-6300-series-fabric-interconnects/datasheet-C78-732207.html

  Unified ports can also be configured as a FC ports for connectivity of FC switch upstream or directly related to CF Storage processors.

  After having watched the datasheet, let me know if you have any other questions, and I'll try to address them.

  You'll not need actually configure ports such as ports 'server' unless you connect servers in a rack.

  Please configure any ethernet SFP type connected to your switches nexus upstream as 'network' uplinks.  I guess that you don't plan on a disjoint config layer 2 (where each FI has several sets of uplinks will different devices upstream, or the same device with different VLANS allowed on each link).    If you are, we can have a separate thread about how you need to configure that.

  Thank you

  Kirk...

• Cisco ucs with VMware 5 auto deploy

  Hello

  In our lab, I test with 5 VMware and Cisco UCS. We run UCSM 2.0 (1 m). I am now to test the auto hand deploy. I have auto configuration to deploy in VMware and it works (first of all, I had some problems with DHCP on windows which is solved in version 2.0 of UCSM (q)). vSphere gets deployed to the blade. When the blade (vShpere) wants to connect to vCenter I get an error of vCenter has enough licesing for this action. I loaded a lot of low-income VMware. When I create a virtual machine, it starts perfectly and apears in vCenter.

  I search on the internet for people who have the problem of the simailer, but could not find.

  Some body the same problem our help me?

  Thanks in advance,

  Robin

  Robin,

  This looks more like a VC related question (UCS) platform.  UCS has no effect on the functionality of licenses of the VC.

  If the host does not connect to the CR, how are you VMs to "start perfectly and appear in vCenter?

  Kind regards

  Robert

• Dell TL4000 Tape Library on Cisco UCS 6120

  Hello

  We have Cisco UCS 5108 2 6120XP fabric of interconnection. We are running VMware on my Cisco blades. I have I need to connect my Dell TL 4000 LTO3 tape library this Cisco UCS so that I can configure a virtual machine with the EMC Networker software for backup of virtual machine data. When I connect the Cisco UCS library, it does not recoginize as tape drive.

  Please suggest how to set up the same.

  Thank you

  Amit,

  We do not support direct damage attach FC tape library to the FI currently.

  It may be a CF or CF storage end switch.

  . / Afonso

• How does Card Crypto knows what ISAKMP policy to use?

   ip access-list extended ACL_SITE1_TO_SITE2 permit ip 10.0.12.0 0.0.0.255 10.0.22.0 0.0.0.255 ! crypto isakmp policy 10 encr aes hash sha256 authentication pre-share group 14 crypto isakmp policy 20 encr aes 256 hash sha512 authentication pre-share group 16 crypto isakmp key cisco123 address 200.0.2.2 ! crypto ipsec transform-set [TRANS_SET]PHASE_2 esp-aes esp-sha256-hmac mode tunnel ! crypto map [CRYPT_MAP]VPN_SITE1_TO_SITE2 11 ipsec-isakmp set peer 200.0.2.2 set transform-set [TRANS_SET]PHASE_2 match address ACL_SITE1_TO_SITE2 ! interface FastEthernet0/0 ip address 200.0.1.1 255.255.255.0 crypto map [CRYPT_MAP]VPN_SITE1_TO_SITE2

  How does Card Crypto knows what ISAKMP policy to use, or use of the ISAKMP policy at all?

  It comes from "ipsec-isakmp?

  I mean... I do not see any "set isakmp policy 10" in the Crypto map

  This is what he chooses just the top-down approach?

  As part of the negotiation of the phase 1 and is a top-down proposal based on the sequence number.  You can get the details in tunnel using configuration:

  Debug crypto ISAKMP

  Cisco IOS has built/strategies default ISAKMP, but the pre 15.x versions were terrible default.  New default values are strong, although I still like to configure them myself.

• Need help on Cisco UCS Certification

  Hi all

  I need your help.

  I intend to take the certification Cisco UCS. Please help me on this I am confused that you take as it is DCUCI or guide DCUCD please if it is DCUCI how to start and if DCUCD how to start.

  Currently working on vmware support and little UCS. I am after reading docs, and communities through videos from train signal UCS.

  Can some expert guide please, how further will be a great help

  Thanks in advance

  Vincent

  Vincent,

  Since how long did you ask? I want to mention that CCNA/P DC was relesed in November, before a review as DCUCI was a full certification and it is now part of the CCNP instead.

  CCNA has 2 reviews, DCICN & DCICT

  I couldn't find a link where it is specifically stated that you must follow a specific order, for example here:

  http://www.Cisco.com/Web/learning/certifications/specialist/DC/uc_support.html you can find specialized support requirements are:

  642-999 DCUCI (one of the basic tests I mentioned) & DCUCT 642-035 (one of the troubleshooting tests I mentioned as well)

  For CCNA, there is no choice, only 2 exams available, it does not matter for CCNP, but 4 you access CCNP, different combinations will give Add tax certifications.

  However, keeping in mind the names of examinations, which can give you an idea of what you want to learn first:

  DCUCI: implementation of Unified Computing DC

  DCUFI: implementation of DC Unified Fabric

  DCUFD: Data Center Unified Fabric Solutions Design

  DCUCD: Data Center Unified Computing Systems Design

  DCUFT: Troubleshooting Cisco Unified Fabric data center

  DCUCT: Troubleshooting Cisco Unified Computing data center

  I hope this helps clarify.

  -Kenny

• How to read the papers of ucs tech support

  Hi team

  Can you please tell me how to read the newspapers of ucs tech support to find out hardware problems

  Greetings.

  Your question is probably something that is difficult to address in this format.

  Hardware and firmware is so rapidly changing, so are the various capabilities of diagnosis (and how, when, where they write to newspapers).  I think that it would be virtually impossible to maintain a full guide updated content of tech support file and how to interpret them.

  That being said, there are some more frequent for both blade/UCSM and stand alone C series servers such as SALT that connects usually record the major mistakes such as chess DIMM, HD failures, etc.

  There are general troubleshooting guides such as http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ts/guide/UCSTroubleshooting/UCSTroubleshooting_chapter_0111.html

  There are also courses that correspond to the review DCUCT 642 - 035 http://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/dcuct.html entering some details by looking at newspapers, among other things.

  Is there some hardware problems that you try searching?  You have some sort of polling app that parses the files you are trying to Setup alerts for, etc.?

  Thank you

  Kirk

• Service profile of the CISCO UCS for ESXi

  Do you need multiple boot LUN on the storage array for each host that you want to apply the service profile to? I'm just confused, let's say I have 12 blades that I want to designate as boot SAN for ESXi, y aura-t 12 profiles of separate service for each of them, and will need me 12 different LUNS on our storage? I am new to this and I just want to make it as clean as possible! Any help is appreciated.

  Hi Justin,

  You can have the same LUN ID for multiple service profiles, as well as the same target ID. However, your initiators will be different and you will need to configure the zoning on your switch upstream if you use the end host mode.

  Here is a good guide, review the basics and how to put in place.

  http://jeffsaidso.com/2010/11/boot-from-San-101-with-Cisco-UCS/

  Also here is an excellent guide to troubleshooting;

  http://www.Cisco.com/c/en/us/support/docs/servers-unified-computing/UCS-...

  Kind regards

• receive calls on the problems on my computer, how does this happen?

  How can I report errors on my computer

  I keep getting calls that my computer is about to crash and they will help you. I'm skeptical of all. How does this person know that something is wrong if I didn't report?

  Camella

  It is a common scam. Do not give them information, do not give them access to your PC and do not go to all the websites that they suggest. One moment. See:

  http://www.microsoft.com/en-gb/security/online-privacy/msname.aspx .

• Cisco UCS C210 M2: PXE - E61: Media test failure, check cable of

  Hello

  I'm working on Cisco UCS C210 M2 servers. I got 10 146 GB SAS HD with LSI MegaRAID Raid Controller. I did run the Raid Controller and choose RAID6. After that I installed ESXi and it said to reboot the server. Now, when I restart the server I get the following error message:

  PXE - E61: Media test failure, check cable of

  PXE - M0F: Exit Boradcom PXE ROM

  Restart, and then select proper boot service

  or Insert Boot Media in some boot device and press a key

  Any suggestions how I can solve this problem.

  Thank you.

  You will need to go into the Bios of the controller LSI MegaRaid (Ctrl + H) and select the option of virtual drives on the left. When the virtual command window opens, you must select the drive (Raid Volume) on which you want your drive master boot and underneath there will be an option to set as your boot device. Apply and save.

• Connection Cisco UCS 6120 FI directly to Cisco Catalyst 6500?

  I watch a lot of design with the Cisco UCS solution guide and everywhere it is Cisco Nexus 5000/7000 connects to the uplink ports of Cisco UCS 6120 FI with the benefits of technology to the vPC.

  How about connect Cisco UCS 6120 FI directly to 10GE ports in Cisco Catalyst 6500 (without VSS and VSS)? It is possible to design?

  If I use C6500VSS there will be port-channel of the aggregation of the UCS Nx10GE all the bandwidth?

  And what happens if I use C6500 (without VSS) - how it will be on the many links between UCS and two boxes C6500? It will be blocked by STP? A little on the other?

  Please explain to me, because we have only C6500 switches in our data center and want to test a Cisco UCS schassis.

  Yes, you can connect the 6120 s to cat6500s with or without vs. With VSS, you get a vPC as port channel where 2 links to a single 6120 can be connected to different 2 6500 s in a port LACP-channel.

  VSS is not necessary, you can connect a 10 G uplinks / 1 G of 1 or more of a 6120 at cat6500s. I you have 2 cat6500s (non - vss) and 2 uplinks by 6120, then you want to connect 1 cat6500-1 and the other to cat6500-2. I would recommend going ahead and creating a single port-channel port so that you can easily add the uplinks in the furture without interruption of service.

  Ideally, for non - vss, I would have 4 10 uplinks by 6120; 2 in a channel port cat6500-1 and 2 in a port in cat6500-2 channel