How to configure the host network to pass

Similar Questions

• How to configure the private network interface between two VMS os invited using red hat linux

  Hello:

  I'm trying to set up a Real Application Cluster on my home office so that I can install Oracle 11 g RAC which is a facility where you have two servers accessing the same shared of storage (chipboard).

  In addition they will have a network interface private and a public network interface, so it will be for public interface eth0 and eth1 for interconnection of private networks.

  I read that I can set up using VMWare server, create Virtual Machines and install the operating system invited to them.

  I intend to install Red Hat Linux guest OS.

  My question is basically, how can I do for the establishment of the private network eth1, will be the guest OS to automatically install the sense (do I need to have 2 NIC cards for this), or where and how can this be configured?

  Also, how these two speeches of Virtual Machines to another on the private interconnect?

  And is it possible to use DHCP or do I need to add the IP addresses manually?

  Very grateful for your contribution to this topic, thank you.

  Kind regards

  Sam

  You can have network private without assigning a NIC cards (adapt).

  Hope this helps

• Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?

  Can someone give an example of how to configure the subnet mask associated with the network and host of an IP address part?

  Hi stuckfree,

  The question you posted would be more appropriate on the TechNet Forums. I would recommend posting your request here.

  http://social.technet.Microsoft.com/forums/en/itproxpsp/threads

• How to configure the network adapter when you run ESXi on VmWare workstation?

  How to configure the network card installing ESXi on VmWare workstation 6.0.0?

  These are the options: I tried bridged, host-only NAP.  None of them works

  

  What Miss me? driver or adapater?

  I'm running on vmware workstation on Windows 7 with Lenovo laptop.

  in the configuration of your virtual machine, the main issue is memory. you gave the 2 GB of RAM, whereas ESXi 6 cannot go forward without minimum 4 GB of RAM.

  If please have 4 GB of RAM and re-run Setup. you will get through.

  message about the network card should also not appear after that. What kind of network you choose depends on your need.

• Configure the host and the VM on two separate wireless networks

  Hello community, I was a browser for a long time, but this will be my first post.

  I would like to begin by saying that I have always found the answer I was looking for by browsing these forums and that I browsed discussions thereon and consulted the chapters regarding virtual networks in the manual workstation 7.1, but at this stage were still unable to solve my problem.

  The scenario:

  I'm a small business working in a House (upstairs) / hookah lounge (bottom). We recently had a second internet connection (WORK), Internet home of my family (HOME), to provide our customers with a free wi - fi. I would use the connection of WORK (during our hours of downtime) in a Ubuntu VM for folding and seeding of torrents. I want to put this far on a network traffic will not affect the other.

  The network:

  SE host: Windows 7 Pro 64-bit

  (Host) NIC: Intel PRO/Wireless 3945ABG (Mini PCI)

  VM: Ubuntu 10.04 on VMWare Workstation 7.0.0 build-203739

  NIC (VM): Alfa awus036h (USB)

  
  

  The current configuration:

  Network connection is made, the State of replication physical physical network is unchecked.

  The Alfa is connected to the virtual machine and is no longer present on the list of the network adapters in Windows.

  It seems that I have to manually disable the "auto eth 1" interface or the virtual machine using the internet connection in host rather than the network of your choice that the Alfa connects to in VMWorkstation. The speed of the internet with eth auto 1 is connected is quick and consistent, but using it defeats the purpose. Strangely, when I go to network connections, under the "last use" for "eth 1 auto ' it is said 'never '.

  When "eth 1 car" is disconnected, it seems that the virtual machine uses the network wireless connected to the Alfa. But the internet speed is very slow and inconsistent. On downloads, the speed varies considerably; Also, it remains at 0 kb/s for a while before going to 80 KB/s, then works his way down to 0 kb/s again.

  Possible solutions:

  1. it's a driver problem for the Alfa inside the VM environment all this time?

  2 just misunderstood how to set up this kind of virtual network?

  3 is it possible to get the desired configuration by filling the WORK and VMnet0/1/8?

  * Note: Only VMnet1 and VMnet8 appear on the Windows network connections, however isn't VMnet0 bridged one responsible for networking?

  4. upgrade to the current version of the desktop would be useful?

  5. do this problem originally because of some settings on the router?

  * Note: The AP is close enough to provide a signal strength of 85-90%

  Sorry to be so talkative, I just wanted to be as clear as possible because I'm still a beginner to learn more about virtualization.

  Thank you in advance, as always, your help is greatly appreciated.

  First of all, I must say that when I did this last response, I've been on my Mac and I thought the configuration of a host of Windows XP however outside the nomenclature of the names of the host network settings dialog box the rest stands as it is on a host Windows 7 as described below, including a picture as an attachment.

  On a Windows 7 x 64 host with two network adapters, each on a different subnet and VMware Workstation 7.1.3 installed with the editor of virtual computer network configured for VMnet0 and VMnet2 jumpered separately to one of the host of NIC and I have not changed the settings for Windows 7 host NIC-1 and have network/Internet connectivity to the host of this NETWORK adapter as shown in the picture of Google in Internet Explorer on the host computer.  In VMware Workstation 7.1.3 I have a Linux Guest configured to use VMnet2, which is filled in the settings and the Windows 7 host NIC-2 have all with the exception of VMware Bridge Protocol unchecked and have network/Internet connectivity in the guest as indicated by Google in a browser.

  From the perspective of connectivity network between the host and the guest by NIC - 2 on the host computer when all with the exception of VMware Bridge Protocol unchecked there is no connectivity between the two on this subnet because there are no protocol at stake to allow the conversation to take place.

  So theoretically and in practice what I said previously, but didn't were not expressly with a Windows 7 host in mind, nevertheless what I said is true and accurate, as evidenced by world real test/use by what I said and with the image attached herein.

  FWIW Windows 7 has been configured with the default settings and the only changes to the host's network were those made during the installation of VMware Workstation 7.1.3 so with the configuration I discussed with the attached picture, there is no reason why the host and the guest cannot be on different physical networks and each network/Internet connectivity based on the information I have provided and they be isolated from each other by being on separate physical networks.

  That said, even if they can be isolated by being on separate physical networks can still can connectivity between the 2 through VMware shared folders it it turned on and of course & slide and other services so if absolute isolation is necessary to the point where it can be, and the guest still operating system run on a Virtual Machine in the host you would need to disable the Backdoor for VMware Tools cannot provide shared folders on VMware, & glide and other services.  So if you need this isolation level let me know and I will provide additional information to complete it.

• How to configure the CD driver on the host for a virtual machine?

  After you create a virture machine and put the CD of driver on host, when powered on the vertual machine, may not start the drive form the CD only from NIC.

  How to configure the CD driver on the host for a virtual machine?

  Right-click on the virtual computer and go to edit settings. Click the Options tab and under the tip list, there should be Boot Options. Enter an amount of milliseconds to wait before your boot, so you can activate the CD-ROM. You can also activate the CD even if it boots to the NETWORK card option, and then reset the virtual machine. Get the focus of this virtual machine on the console session, and then press ctrl-alt-insert. Your CD-ROM will stay connected if you do not want to delay the startup process.

• My IP security camera is different my network ip address, how to configure the camera to match the ip address with the router cable time Wörner

  Please someone help me configure my camera IPsecurity model m12 mobotix ag. It allows to work in the corporate network, but they close down and I didn't bring the camera House but there different IP address of my network and I don't know how to configure the camera to have the same IP address with my home router to TWC, thanks

  Router connections by opening network, in the Panel control, search for the router / properties, enter its configuration

  data in the boxes provided, you will get on the router, a sticker shows data. If lost or deleted, go to its Web

  for the data. Also, perhaps the home page of IP camera offers software/drivers.

• error "could not complete the configuration of the ha agent on the host computer.". misconfiguration of the installation of the host network.

  Hola y buenos dias, he puesto 2 hots directly in una DMZ y al activar el error HA da este:

  "Unable to complete the configuration of the ha agent on the host computer.". misconfiguration of the installation of the host network.

  ESTOS son gemelos servidores y poner esta durante 2 Años last config antes han estado dentro infraestructuras en a cluster con otros 4 running perfectly. Ante nueva situation that met responsible security perimeter solo our esta posibilidad por lo as procedimos dio el a preparar los hots ante the nueva config enchufamos estos y an el swhitch of the demilitarized zone.

  Según me ha EDI el responsible of security perimeter, todo el trafico desde estos 2 hots hasta el esta allowed vCenter y asi mismo el cortafuegos responde al trafico ICMP a estos hots (este tema that he read in various Québec sites are important para el HA).

  Version of hots los Esxi 4.1.0 721871

  Me falta algo o tengo algo configurado evil?

  Important Algo a revisar?

  A greeting is gracias por adelantado

  Buenas

  Me designed that tendras 2 con 2 direcciones distintas vmkernel (lo del tema Las vlan y las tarjetas're menos ahora lo)

  Prueba has see the resolución desde el propio ESXi, prueba el uno a otro por both vmkernel ping, etc...

  A malas, saca ambos nodos del cluster y vuelve a unirlos con desactivado, cuando tengas los 2 HA, activa HA of nuevo y con eso you can smear of dudas so por el tema del VC University y UN vicio en BBDD.

  If todo esto falla, have as plantearte touch en el aam, are fairly complejo y peligroso if no to sabe hacer correctamente.

• How to configure the network device agent

  I added a network device (router) in the new platform, its not to go for all of the alerts in tool Hyperic. How to configure the network device to get information to the Hyperic server. Do we need to do any configuration of SNMP.
  
  Can someone help me please.

  Hi Cyndhya,

  Do you mean you want to see traps SNMP generated by your device network at HQ? To do this, you need to configure one of the agent HQ to receive traps and configure the network device to send the trap to the agent. Once this operation is complete, you should be able to add the device network platform (you must use the agent HQ for the monitoring network device connection).

  Here is the step by step guide:
  http://support.Hyperic.com/display/DOCSHQ30/agent+SNMP+trap+receiver

  Koffi

• After you move a crowd is to Cluster HA, got a misconfiguration in the host network configuration

  An existing host works well in the datacenter, which only had a NIC card. But he moved to Cluster HA, got

  HA configuration

  10.1.1.203

  Unable to complete the configuration of the

  HA agent on the host computer. See the details of the task

  For more information. Incorrect configuration

  in the configuration of the host network.

  Incorrect configuration

  in the configuration of the host network.

  It takes longer for HA NIC card? But, on the procedure for creating HA, not this requirements.

  Thank you!

  George

  Looking at your screenshots I would suggest that you create the second and third vSwitch with 192 and 172 port groups that exist on the other host.

  André

• How to configure the router Linksys DD - WRT for WVC54GCA E4200

  I don't know how to configure the router Linksys DD - WRT for WVC54GCA E4200. DD - WRT is very complcated. Help, please! Also, I used the TZO.com to the DDNS. Can I set up the DDNS for DD - WRT router? I used the DDNS to my old model router before. Thank you.

  I followed the TZO supporter last night. I can watch my WVC54GCA outside. All solution links:

  http://tzodns.com/support/tutorials/188

  http://tzodns.com/support/tutorials/190

  Hi Majekho,

  Your domain name has decided to 99.245.xx.x. If you go to www.test.tzo.com from the location of the host, you must see this IP address. If these numbers are the same, then all with TZO works correctly. I guess that it is a simple problem with ports (80, 1024) is not open in the router and forwarded to the right internal IP address of the device (for example. 192.168.1.xxx).

  In addition, if you have a DSL, you will need to call your ISP and ask them to show you how to put your modem in "bridge mode". This will disable the firewall in the modem that blocks incoming connections even if you open ports in your router.
  In addition, during the test, it is best to test on your device remotely, this is due to a common problem called loopback with most routers. For more information about looping, take a look at:

  http://helpdesk.TZO.com/cgi-bin/KB.cgi?view=140

• How to configure the settings of mail on HP Laserjet Enterprise 500 color MFP M575 printer/scanner?

  How to configure the settings of mail on HP Laserjet Enterprise 500 color MFP M575 printer/scanner?  The Office has 5 staff members each with ending with [email protected] for example e-mail addresses.  We have also created an email for option analysis as [email protected] (not sure if creating an e-mail address for the scan option is required).  We are not part of any domain, and there is no server in the office.  When you try to configure the email on the printer/scanner control panel it asks the host name.

  What host name that I can use?

  If you try to configure the browser by using the IP address of the printer, he asks as the SMTP server. The MS Outlook 2010 all our emails use mail.junior - albania.org incoming mail server and outgoing.  Other settings in MS Outlook 2010 are box My outgoing server (SMTP) requires authentication checked and use the same settings as my mail server entering selected.  On the Advanced tab: incoming server (Pop3): 110 (SSL encryption is not checked) and outgoing (SMTP) server: 465 use the type of encrypted connection (SSL) following.

  What server SMTP should I use in this case?

  I would appreciate your help in the configuration of the HP printer/Scanner for scanning and sending by electronic mail to the members of the office staff email addresses.

  Thank you...

  I'll link you to the product page with several documents which I hope will help you to configure your e-mail settings. Please look through them and see which ones fit your needs:

  Scan and send (e-mail, send to folder, digital sending, etc..)

  Here is another site that has some videos that will guide you through the entire upward (here I would try everything first )

  Simulations of MFP - digital send

  If these don't work, please let me know and I will continue to search it for you.

• How to get the host name of the physical computer inside a virtual machine until the user logs in Windows?

  I don't know if this is the right place to post this question, I develop software to support VMWare PCoIP and need to know how to get the host name of the physical machine (which manages the virtual machine and View Client) within a virtual machine before the user logs in Windows of the virtual machine.

  I understand there are two ways to read the host name, via the HKEY_CURRENT_USER\Volatile Environment registry and environment variables, but they are available once the user is connected. I need info before the user connects.

  Is there a VMware API that can be called or asked the host name?

  Thank you.

  Not on the broker, but there are the startup scripts to log on to the computer virtual itself: http://pubs.vmware.com/view-52/topic/com.vmware.view.integration.doc/view_integration_startsession_script.9.2.html

  Note that these executed when a virtual desktop computer allocated connection, not to the point that the client connects - it is possible for the customer to not complete the connection (crash, cancel, network failure) and so any what solution you design must handle this.

  Mike

• How to configure the e-mail address of the form home and contact me form

  How to configure the e-mail address of the form at home and contact me form. I got two WARNING when exporting my muse as HTML file

  Muse will give the alert message if the e-mail address used is not on the same domain as hosting many platforms is not supports the emails from the external domain.

  You can check with your accommodation, where they take over other emails from field so it will not be a problem and you can ignore the warning message.

  Thank you

  Sanjit

• Printer all in one HP3520 - how to select the wireless network and enter the WEP key?

  According to print my wireless network is detected.

  How to connect the! @# % printer $ fo the wireless network and enter the WEP key?

  Instructions on the HP site tell me to selet NETWORK on the printer control panel.  Well, there's a way to select the NETWORK from the control panel.  It is not an option for him.

  I downnloaded and installed the latest drivers.

  I have restored the default settings.

  How to select the wireless network and enter the WEP key?

  All of HP's instructions seem to be for a newer printer with a touchscreen.

  I want that the printer is connected to my main computer via the USB port.  I want to be able to print wireless phones and tablets.

  My 3520 is not a 'touch Screen' and it has wifi.

  However, the following work:

  Try to open the HP Deskjet 3520 icon, open the utilities tab, click on convert USB wireless, by following the steps on the screen.

  This leads me to believe that ONLY the wireless doesn't work.  I know now that the part of the sentence "Convert USB to wireless connection" is supposed to mean "works like USB and wireless.

  Thank you for your help