How to configure Windows server 2008 r2

Similar Questions

• I would like to know how to install Windows Server 2008 and Windows 7 Enterprise from a USB key, please.

  I would like to know how to install Windows Server 2008 and Windows 7 Enterprise from a USB key, please.

  I'm not trying to run either on the USB key, I just need to know how to install from a USB key. I tried Multiboot, grub for DOS and other, but they do not seem to work :/

  I am going through a book that uses these two to form Microsoft MCITP: Server 2008 Administrator and if I could install these Via USB, this would save my records and a lot of hassle... basically just for convenience, as everything that I need will be on a stick * lol *.

  Otherwise, I'll have to use discs instead :)

  Take a look at this:

  http://www.Haiders.NET/post/installing-Windows-Server-2008-from-a-USB-Flash-pen-drive.aspx

  Like to make a bootable USB with WIndows 7, take a look to use the following:

  Download Windows 7 USB/DVD tool

  http://store.Microsoft.com/help/ISO-tool

• How to: install Windows Server 2008 R2 (64-bit) in ESXi 4.1 - 260247 with controller 'LSI Logic SAS'?

  Hello

  I have a newly installed ESXi 4.1 - 260247 on a Fujitsu - Siemens GROUND RX300 S4 with 2 x Intel Xeon E5420 @ 2.5 GHz with 36 GB of RAM.

  Storage controller is a LSI MegaRAID SAS 1078 6 x 750 GB SATA - drives configured with 3xRAID-1 logical drives. BIOS Version 4.06 Rev 1.04.2519

  Now, I'm trying to install "Microsoft Windows Server 2008 R2 64-bit" in a virtual machine, but fail because the virtual hard disk cannot be found.

  I tried with all Types of SCSI controller, but when running of the "Create Virtual Machine"-magician, he suggests 'LSI Logic SAS'. "." I tried 'LSI Logic parallel' and "VMware Paravirtual" but it did not work. However, I have not tried "Parallel BusLogic", since it clearly says no "recommended for this guest operating system".

  I was unable to find documentation on how and where I can find the "LSI Logic SAS" - pilot to be able to continue the installation. The

  Windows Server 2008 R2 installation is an ISO obtained directly from Microsoft eLicensing.

  I also downloaded the drivers floppy 'pvscsi - Windows2008.flp' and 'vmscsi.flp' from the ESXi server, but the program finds no driver validates the installation of Windows on them.

  I also extracted files "windows.iso' of the ESXi machine, but not drivers there as well.

  So my question is, what model is the "LSI Logic SAS", I guess I can download these LSI directly, I need to know what model?

  Any help appreciated.

  Thank you!

  Kind regards

  Christian

  chrkad,

  I think you have the same problem I had.   Trying to install 2008 R2 and asked for drivers?

  The issue wound up being an ISO corrupt Ms.

  Try to download the ISO using the java-based download manager.  This will tell you if your download is getting disturbed, as mine was.  It will also be the image once completed to ensure you've got the whole thing of checksum.  Just download via HTTP does not.

  I found myself in download the image of the House and burn a DVD and realize that the back of the office,

• How to downgrade windows server 2008 r2 for Server 2003?

  I bought windows Server 2008 but license my workplace always use Windows server 2003
  How can I demote the Server 2008, Server 2003
  Give step by step instructions and all necessary means

  Thank you for visiting the Microsoft Answers site. The question you have posted is related to Windows Server 2003 / 2008 and would be better suited to the Windows Server TechCenter community. Please visit the link below to find a community that will support what ask you:

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads

• Installation of PowerEdge R220 Raid Configuration + Windows Server 2008 r2

  I have dell poweredge server R220 am tring to install windows server 2008r2, but can't so please guide me how to install before the end of March I should install os

  What do you mean 'impossible'... What's the problem?

• Failed to configure windows server 2008 with a fixed IP address on VMware WS 9.0

  I have VMware Workstation 9.0 installed on my Windows 7 Ultimate on a Dell precision 4700. Intel I7 2.6 GZ (8 CPUs) and 16 GB.

  I have developed networks to open and

  Hi André,.

  I think that I thought about it.

  (1) in the virtual network Editor, I needed the jumpered to connect to the wireless card active network connection

  (2) I had a firewall problem

  Thanks for the help,

  Chris Schene

• How to configure the mode of kiosh for thin clients on windows server 2008

  I have an eight Thin Clients who will use RDP to access (Terminal Server Services) Remote Desktop Services on a Microsoft Windows Server 2008 R2 Standard. I would like to set up a group of users for these Thin Clients to be in a mode Kiosh so that they have very limited capabilities, can not download and run anything, unable to save anything in the computer except on the desktop and when they log off and back on everything, they had disappeared because the mandatory profile is loaded again.

  I'll have another group that more access is needed.

  Kiosk.

  Post in the Windows Server Forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• How to install the ssl certificate in windows server 2008?

  Hello

  Can someone give me the steps to install the SSL certificate on my application hosted on windows server 2008 R2?

  Hello

  Although technet.microsoft.com should be the best forum for the problems of server below is a guide on how to install an SSL certificate.

  It will be useful.

  To install your newly acquired in IIS 7 SSL certificate, first copy the file somewhere on the server and then follow these instructions:

  1. Click on the start menu, go to administrativetools and click on Manager of Services Internet (IIS).
  2. Click the server name in the links on the left column. Double-click server certificates.

     

  3. In the Actions column to the right, click Complète Certificate Request...

     

  4. Click on the button with the three points, and then select the server certificate that you received from the certificate authority. If the certificate does not have a .cer file extension, select this option to display all types. Enter a friendly name that you can keep track of certificate on this server. Click OK.

     

  5. If successful, you will see your newly installed in the list certificate. If you receive an error indicating that the request or the private key is not found, make sure that you use the correct certificate and you install it on the same server that you generated the CSR on. If you are sure these two things, you just create a new certificate and reissue or replace the certificate. If you have problems with this, contact your certification authority.

     

  Bind the certificate to a Web site

  1. In the column of links on the left, expand the sites folder, and click the Web site that you want to bind the certificate to click links... in the right column.

     

  2. Click the Add... button.

     

  3. Change the Type to https , and then select the SSL certificate that you just installed. Click OK.

     

  4. You will now see the listed link for port 443. Click close.

     

  Install all the intermediate certificates

  Most of the SSL providers issue certificates of server out of an intermediate certificate so you will need to install the intermediate certificate on the server as well or your visitors will receive a certificate error not approved. You can install each intermediate certificate (sometimes there are more than one) by following these instructions:

  1. Download the intermediate certificate in a folder on the server.
  2. Double-click the certificate to open the certificate information.
  3. At the bottom of the general tab, click the install Certificate button to start the Certificate Import Wizard. Click Next.

     

  4. Select place all certificates in the following store , and then click Browse.

     

  5. Select the Show physical stores checkbox, then expand the Intermediate certificate authorities folder, select the below folder on the Local computer . Click OK. Click Next, and then click Finish to complete the installation of the intermediate certificate.

     

  You may need to restart IIS so that it starts the new certificate to give. You can verify that the certificate is installed correctly by visiting the site in your web browser using https rather than http.

  Links

  • Move or copy an SSL certificate on a Windows Server to another Windows Server
  • How to disable SSL 2.0 in IIS 7
  • How to configure the SSL in IIS 7.0
  • Video tutorials to install an SSL certificate in IIS 7 to NetoMeter

  Kind regards

  Joel

• Cannot configure GPIB in Windows Server 2008

  I installed the version 2.8 IEEE488 driver on a Windows Server 2008 computer.  I have successfully added a GPIB-ENET under Measurmeent and Automation Explorer interface; However, he does allow me to change the configuration of the interface.  I get the message "the GPIB Interface Properties cannot be changed by an administrator" in the status bar.  I am the administrator for this computer group.  Does anyone have any suggestions?  Is there a different usergroup that I need her?  File permissions need to be addressed?  Is there another configuration setting that I need to do?

  I solved the problem.  Run as administrator.  Not enough coffee this morning.

• D20 problem of configuration of Windows Server 2008 R2 / 1 x SATA HD / 4 x SATA SSD

  Hi all

  I have a Mod D20. 4155 and want to use next to it is by default SATA HDD SATA SSD four disks of virtual machines. Windows Server 2008 R2 will be the OS with the use of its Hyper-V features.

  I have Aproblem with detection of drives in the configuration of the operating system. All 5 disks are visible in the Marvell controller BIOS setup. It is possible to configure a RAID on the SSD, etc, but I don't "see" any disk in the configuration of the operating system. I tried to load additional drivers in the part of the Setup utility GUI, but it did not work. I tried with the driver Marcell SAS and Intel Matrix driver, both located at http://www-307.ibm.com/pc/support/site.wss/migr-72280.html.

  Suggestions for the BIOS of the PC / BIOS Marvell / OS installation configurations?

  Best regards, Chrischmi

  Hi all

  I found the solution myself. After detection, the default drive is a SATA drive (and), I got the idea to test it on the Intel SATA controller. It was possible to install the spirit of the machine the disks attached to the Intel controller. After installation, I went to Device Manager and installed the driver of Lenovo Marvell, rekindled the Marvell controller disk and started the. Successfully. Yes!

  On my way to the solution, I had another problem: in the setup of Windows GUI part, I got an error of 0 x 80300001 with Lenovo's Intel SATA driver. It was not possible to install windows Server on the SATA drive with reason0x80300001. very helpful post, Microsoft! (-) I decided to use the default Microsoft for the Intel SATA controller driver after a reboot. Installer executed well, but ended with an error 0 x 80070017 and problems of copy of (unknown) files. The solution (found after a few hours...) was to burn a new installation of Windows Server DVD. I don't want to talk about it anymore...

  -Christoph

• Services Terminal Server Windows Server 2008 R2 improved Configuration Error IE

  We have a Windows Server 2008 R2 with enhanced IE configuration set to off for all users on the Server Terminal Server services only.  The sessions of the Terminal services Server running Windows XP.  Whenever an end user clicks on Microsoft Outlook in a session, it executes an error from IE Configuration improved mentioning that the site needs to be added to the zone of confidence (subject: internet.)  Unfortunately, I do not know what url he speaks out.  I would like to know what precisely needs to be disabled in order to avoid the mistake of filling.  We have already defined group policy to disable this, but apparently not take after or gpupdate/force runs a logoff of connection occurred.  Of alternatives that anyone can give would be great.  Thank you very much.

  Nick

  This issue is beyond the scope of this site which is for the consumer to related issues.
  To ensure that you get a proper answer, ask either on the Technet site, if it is a type of Pro problem, or MSDN if it's related to the developer
  *
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum

• I bought windows server 2008 R2 standard and Enterprise edition to install incorrectly, how do I activate windows?

  I bought windows server 2008 R2 standard and Enterprise edition to install incorrectly, how do I activate windows?

  Hello

  Please post your question in Server TechNet Forums.

  http://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  See you soon.

• How should I / can I install Windows 8 policies on a Windows Server 2008 system.

  Hello

  I am currently working on a customer's server that is running Windows Server 2008 R2. They are trying to upgrade their machines to Windows 8.

  The problem they have is that they don't want all the extra tiles on metro screen, so I exported a model of how they want it to look. The problem I have at the minute is to install Group Policy settings 8 windows on their server, so that I can put the filter pattern of departure for all machines in the domain.

  How to properly install Windows 8 strategies on the system? I downloaded them as files admx on the MS site ready to go, but it is not as simple as I thought.

  Thanks in advance,

  Kaelan. IARC - Smith

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• How to install Windows 8 Pro cd image in the Windows Deployment Services on the 32-bit version of Windows Server 2008?

  Hello.

  I wanted to ask you for example in Windows Server 2008 32-bit when there are Windows Deployment Service. From there you can add images and then you can install windows on the network. So I wanted to try to do it with the cd Windows 8 Pro where I but I couldn't do that because in the catalog of Sources, I find "install.esd" not "install.wim" how the server or service request, with the cd of Windows 7 you can do, but you can't do that with windows 8 Pro I have buyed haved. I want to try to do this with Windows 8 Pro cd on the network because I have 3 pc at home with Windows 8 Pro and I wanted to try out the service deployment with windows 8 when I need to install pc so I prefer to install it on the network not on cd or etc. P.S. for all PCs with windows 8 pro I have buyed them, I have license key and etc.

  I use the 32-bit version of Windows Server 2008 in thw.

  Hello

  You can view this issue in this help link:

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  It will be useful.

• How can I connect to my server (which runs on windows server 2008 rc2) via IP REAL using rdp, while the VPN connection is active?

  Hello

  How can I connect to my sServer (which runs on windows server 2008 rc2) via IP REAL using rdp, while the VPN connection is active?
  

  Hello Marie Smith.

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the link below.

  http://social.technet.Microsoft.com/forums/en-us/winservergen/threads/

  Hope this information helps.