How to implement a time UI?

Similar Questions

• How can implement you not with Tim Capsule and AirPort their simulation on the iMac?

  Hello

  How can implement you not with Time Capsule and AirPort their simulation on the iMac?

  I don't know what you're asking.

  AirPort Extreme is a wireless router.

  A Time Capsule airport is an AirPort Extreme with a built-in hard drive for data storage.

  An iMac is a Mac computer.

  An iMac is not a wireless router, so he is unable to perform the functions of a wireless router.

• Implement a timer on an SMU-6361

  I need to implement a timer by using one of the counters/Timers on a SMU-6361 Multifunction DAQ module. I don't find any help on the web view OR to implement the timers.  I guess to study the manual of the X series that I would use the single pulse generation with trigger function.  I need assign a clock shipped as SOURCE, assign an entry PFI as the DOOR (Start Trigger), set the value of the impulse for my timing delay, define the pulse width and assign a PFI as the OUTPUT Terminal.  However, I can't find any information about what nidaqmx functions I would use to perform this action.

  Can anyone address this operation?

  wkesling3 wrote:

  All examples of OR are for the meter entry tasks. Everyone says to use the example of counting digital event that needs to be changed to make it work.

  It of weird, is it some sort of filtering option in CVI?  I have examples of ANSI C meter output to:

  C:\Users\Public\Documents\National Instruments\NI-DAQ\Examples\DAQmx ANSI C\Counter\Generate Pulse

  I took out the DAQmx calls from the code you have written so that they are easier to see on the forum:

  DAQmxCreateCOPulseChanTicks (EchoTaskHandle, chan, "", "/ PXI1Slot3/20MHzRefClock", idleState, initialDelay, lowTicks, highTicks);                                                                                                       
  
  DAQmxExportSignal (EchoTaskHandle, DAQmx_Val_CounterOutputEvent, "/ PXI1Slot3/PFI3");                                                                                      
  
  DAQmxCfgDigEdgeStartTrig (EchoTaskHandle, "/ PXI1Slot3/PFI4", DAQmx_Val_Rising ");
  
  DAQmxStartTask (EchoTaskHandle);

  I see only a few small changes to make:

  20MHzRefClock is not a valid terminal, you probably want to use 20 MHztime base.

  Instead of DAQmxExportSignal, I use DAQmxSetCOPulseTerm.  The output is already on one of the default PFI lines (depending on the meter) and setting the output of an explicit PFI line will change the output terminal.  Export the output event counter I think sends the output of a second terminal (I'm not positive if flippant... calls might actually be equivalent, but DAQmxSetCOPulseTerm is most commonly used).

  You define the task to be redeclenchables if you intend to trigger the exit several times (DAQmxSetStartTrigRetriggerable).  You could alternatively, you can restart the task after each trigger in software, but this is inefficient and you will have several ms downtime compared to the redeclenchables task which will be immediately re-army after the release completed (within 10 seconds of ns anyway).

  wkesling3 wrote:

  Hi John,.

  When (or why) would be the next function call used when the output is already
  
      defined in the DAQmxCreateCOPulseChanTicks()   function call.
  
  //
  
    DAQmxErrChk (DAQmxSetExportedSignalAttribute (taskHandleDist,
  
                                                                      DAQmx_Exported_CtrOutEvent_OutputBehavior, DAQmx_Val_Pulse));

  The meter has in fact two different modes.

  "Toggle" is the default value for the tasks of the meter output, in which the output of the meter will switch to the opposite value when it reached number of terminals (how a new value is loaded into the account register and the meter begins to count down).  So in your case, 'Initial period' will be loaded first, then when the meter lorsque le compteur atteint reached TC output will rise to high and "High Ticks" is then loaded into the registry.  When the counter reaches TC again the output will switch down (and in your example pulse, the output will stop - in the generation of pulses multiple 'Low Ticks"would be then responsible).

  "Pulse" mode the meter emits only a short pulse (I think 2 ticks long timebase) when it reached TC.  It is used by default on meter entry tasks (for example the meter output can serve as an event to detect overview for the tasks of entry conditions).  Exit tasks can be configured to "Pulse" too, but in this case the names 'high ticks' and the ' weak ' are unsuitable because the output signal is high only for a very short time (they would be more appropriately called "interval 1" and "interval 2" or something like that).

  Most people just use the default behavior and explicitly set the output behavior unless they have a reason to change the default (which is rare).

  Best regards

• How to implement point filters fixed for FPGA

  Hello!

  I am applying the bandpass filter Butterworth for FPGA.

  I managed to develop filters of fixed point that suits my needs, but I don't know how to implement on a table in a project after the FPGA code generation. I tried to understand it in the examples, but I was not very successful.

  My time to finish what runs, any help would be really appreciated...

  Any suggestions?... some examples?

  Thanks in advance

  I've already done that and solved the problem.

  In any case thank you and have a nice day

  Ljubica

• How to implement the reading of data from a matte file on a cRIO?

  Hi all!

  I'm still not sure, it is plausible, but I'll ask rather before you begin complicating. So far, I found no useful information on reading in the data to a device of RT from a file (type of a simulation test - data is simulated).

  I have the MatLab plugin that allows the storage of data read a MAT file, which has a number of columns that represent the different signals and lines representing the samples at a time (depending on the time of the sample - sample every time has its own line of signal data).

  I have no idea how to implement this at cRIO.

  The idea is:

  I have some algorithms running on the controller of RIO in a timed loop. As the entries of these algorithms I need to access each of the values of columns in the row, which is the time of the sample (sort of a time series - without written actual times).

  I am fairly new to RT and LV development, so any help would be appreciated.

  Thank you

  Luka

  Dear Luka!

  I think the reading of all the samples in a single channel is exactly what you need here, because reading the files may take some time and is not deterministic, so it is best to read all the data in memory (or if this is not feasible due to problems of size, fairly large pieces may be sufficient). The table read can be provided and then in the loop simulating outings, something like this:

  

  I used here separate channels so it's more graphic, but you can build all the channels in a 2D array and array index corresponding to the samples fom 1 who. You can also use for loops with indexing as tunnels are setup and then you won't need the index functions and the number of iterations is also set automatically, but you have to take care of synchronization settings.

  Best regards:

  Andrew Valko

  National Instruments

• Found that the solution does not know how to implement

  Hello

  In my reports (using oracle obiee 11.1.1.7.0) I need to display the values in the chart in percentage and value at the same time, but I don't know how. (for example in a pie chart, I can only see one, either the actual value or percentage of the slice)

  I found this solution the percentage and value of pie , but I do not know how to implement it.

  The solution is to apply this:

  FormatString = '_VALUE %, _PERCENT_OF_CATEGORY % '.

  
  

  OK, but where? and how

  Anyone want to explain further? Thank you
  

  Thanks ofr version information.

  As I said, the solution of John was for 10g, which means a version where OBI has always used the engine Corda to render graphics, and so there was the *.pcxml files which you can hack.

  This solution is no longer applicable since 11g and I think that there is no work around at the moment. At least the last thread of 5-10 on the subject gave no tangible results IIRC.

• How to implement the process of climbing BPM 11 g?

  Hi Experts,
  
  Can any help with process step by step how to implement climbing for 3 levels...
  
  For example, User1 doesn't complete the task at some time say 1 day then this task must be wound to its Director Say User2 and if is not finish it even then it must be the second Director of level for 1 day as well for the third level manager.
  
  Note:
  Where as one when user 1 task is up to the manager (User2) then user 1 tasks should be sent to the User2, even if its value from table.
  
  Please please experts throw some idea on this with an example...
  
  
  Kind regards
  Pavan

  Hi Pavan,

  There are couple ways to do this. This is the very detailed description of what you would do if you want to set your climbing inside the process using the timer to limit events.

  1. Add three interactive activities and put them in three roles representing the roles for your users 1, 2 and 3.
  2. Add a "Timer intercept the event" on the edge of your Interactive activity for your user 1. Associate the new timer event with Interactive activity for your user 2. This will create a new event of border and climbing you want for the user 1.
  3. the name of the new event to limit 'Question degenerate'-> in the "Application" tab, define the new event of the timer limit as an event interrupting-> specify the range to be "1 d" (one day).
  4. in the same way, add another event of the timer limit interruption between your interactive for user 2 and 3 activities.

  I could have missed something, but it looks like your table is just a process data object variable that will be made as part of the payload with the work item instance when he travels through the process.

  For human tasks for user 2 and user 3, you must assign the task to the Manager of the previous participant.

  Hope this helps,
  Dan

• How to get the time(hh:mm:ss) system in the file jspx himself.

  Hi I am using jdeveloper 11.1.1.3.0.
  
  I have a transient VO attribute (data type is Timestamp and format is HH) and created the data control. Now, I am drag and drop this attribute in a single file jspx himself. If I run this average of page that I need time current system as an output. He'll run automatically in the output (such as digital clock - HH) page. How to implement this one help me please Sir.

  Have you seen this: {: identifier of the thread = 2126645}

• How to display date / time in the browser console?

  How to display date / time in the browser console?

  You can set through the Options (gear icon) page in the Web Console (Firefox/tools > Web Developer).
  This applies to the browser console and the Web console.

  • https://developer.Mozilla.org/Tools/Web_Console
  • https://developer.Mozilla.org/Tools/Tools_Toolbox#settings

• How we implemented personal signatures in Thunderbird?

  How we implemented personal signatures in Thunderbird?

  http://KB.mozillazine.org/Signatures_%28Thunderbird%29

• How to set the time that my screen stays on?

  How to set the time that my screen lights up.  I have an iPod Touch 6?

  Settings > general > auto-lock

• How to set the time between slides in a slideshow (iPhoto, el capitan)

  How to set the time to say - 5 seconds or 20 seconds - between slide show photos in iPhoto. I use el capitan.

  See the Settings button at the bottom right of the toolbar (at the bottom of the slide show). Click on it and you have a small window with two tabes, refers to all the slides, the other to the selected slide. You can make your choice

• On Apple Watch, how to change the time when traveling to a different country, like London or Singapore?

  For Apple Watch, can someone please show me how to change the time on my watch when I travel to another country, like London or Singapore? Thank you.

  Hello

  When traveling to a different time zone, it is not necessary to manually change the time on Apple Watch.

  After turning off the flight on each of your iPhone and Apple Watch, the time on your watch can be updated automatically to reflect the local time.

  If it is not the case, try restarting your watch:

  -To switch off your watch: press and hold the button side until you see the cursor off the power; slide it to turn off.

  -To reactivate: press and hold the side button until you see the Apple logo.

• How to import all times - not only the role of the iPhone camera?

  My hard drive with all my photos are dead. Fortunately I've stored them all on my iPhone. However when I go to import Photos to Mac I can import only photos taken on the device. How to import all times?

  However when I go to import Photos to Mac I can import only photos taken on the device. How to import all times?

  Your photos have been synchronized to the iPhone via iTunes?

  Then the mac cannot import photos from iPhone photos.  Synchronized pictures are not stored in the camera.

  Apple recommends to retrieve the synchronized photo sharing by e-mail.

  Sync photos to your iPhone, iPad, and iPod touch in iTunes - Apple Support

  • You cannot re-import photos synced from your computer to your device to your computer. You can only import photos from your device, or record, in your device to your computer. If you need recover photos synced from your device, send photos of the unit yourself. Then download the photos from the emails on your computer.

  It is heavy, because you cannot share multiple photos at once.

  Look for a third-party application that allows you to transfer pictures, for example http://www.wirelesstransferapp.com/

• How to remove backups Time Machine to a specific drive

  I can't find how to better use Time Machine in my situation. Here is my configuration:

  I have a 6 TB external drive dedicated as a Time Machine backup. It backs up my internal drive as well as the three external drives (A, B, C). Player "A" is always connected and is constantly supported, but readers 'B' and 'C' are linked only from time to time to archive older files.

  I recently made a few changes on the disc 'B' and left connected so it was saved, but Time Machine tells me I don't have enough room... it seems he's trying to save the whole 1.3 TB of data rather than the 15 GB or if I've changed.

  I'd like to time Machine would be just delete old backups from the 'B' drive specifically, but except that, what I would do is manually delete older backups for just the "B" drive get rid of enough space to do a new backup, but I get an error when you try to delete the files off the backups. How can I get rid of backups for a specific player?

  Thank you!

  Visit Time Machine FAQ of Pondini helps with Time Machine. You will use the Time Machine application in your Applications folder for managing backups. There is an excellent explanation on the site linked above that explains how to remove backups or backup files.