How to remove the cover of the expansion Bay/PCI-e?

Similar Questions

• 2015 envy 17 t-n100 I76700HQ: how to remove the back cover of a 17 t-n100 envy?

  Hello, I upgrade my Ram and hard drive 16 GB of Ram and 1 TB ssd drive. I looked everywhere, but for the life of me I can't find any info on how to remove the back cover. There are utube videos that show older versions, but they are completely different. You can provide any help would be greatly appreciated.

  Thank you

  Hello

  Did you know that it's a job for parts of authorized service provider ? If you wish, for the RAM, try it please:

  1. turn off the computer. If you don't know if the computer is off or in hibernation, turn on the computer and then stop it through the operating system.
  2. remove power from the computer by disconnecting the power cord from the computer.
  3. disconnect all external devices from the computer.
  4. remove the battery (see battery on page 27).
  5. remove the optical drive (see optical drive on page 28).
  6. remove the bottom cover (see low cover on page 31).

  as mentioned on page #38 of the following record:

  http://h10032.www1.HP.com/CTG/manual/c04696907.PDF

  DIY will void the warranty.

  Good luck.

• I want to know how to remove the back cover of my HP Pavilion Sleekbook 15 to install the new memory?

  I want to know how to remove the back cover of my HP product name: HP Pavilion Sleekbook 15 to install the new memory?  All site shows HP Web is how remove caches memory.  Unfortunately, with the newer models like mine, the whole back cover needs to be removed.  I have tried in vain to remove it, but so far all that I managed to do is scratch my cover.  If anyone can help?

  Dear David

  It's a very good idea, it would also be a good excuse to use my new phone for this.  So I'll say thanks again for the good advice.  Have a great weekend you Mr.  As I said earlier, you're a star...

  Yours Sincerely

  Alan

• XPRT: How to remove the battery cover?

  How to remove the cover of the battery on the XPRT correctly? You lift up the slot on the bottom next to the mic or what? Nothing really seems to drag...

  Hold the phone upside down, the back facing you, place your middle finger

  into the slot that is located just above the speaker.

  A little pull with your middle finger back enough to place your index finger and

  ring finger away from each side.

  Place your thumb in the center of the lid, close the Motorola "M" logo

  Pull with your index, middle and ring finger with your thumb as

  leverage and the back will be open.

  You can remove the lid of the compartment from the rest of the way by pulling

  you.

  The back door is pretty thin, so be careful not to overdo with

  your thumb, you try not to snap paused just half, the 'seal '.

  the bottom of the phone.

  On Saturday, June 25, 2011 at 22:19, rwhite

• Studio XPS 8100 - how to remove the cover of the modular Bay?

  I would remove the plastic cover of the modular Bay on the front of my venerable Studio XPS 8100 so I can install a USB 3.0 3.5 inch hub instead. However, I can't find instructions for it. In fact, I can't find any description of how to use the modular Bay.

  To start: how to remove the cover plastic modular Bay?

  Also: If someone has found the instructions on how to insert a player or another device in the modular Bay, I would be glad to know where I can find them.

  Hello rdunnil

  I took off the glasses and I saw how the metal plate is attached. Applying light pressure with a screwdriver flat head will do the job. Exchange on USB 2.0 ports would also work: I found directions for the removed from their metal case. Whatever it is, I'm all set. Thank you for pushing me in the right direction. It is much more valuable than the useless, generic link you gave me.

• Satellite M35 Pro - how to remove the screen bezel?

  Hey everybody,

  Please help me, I was able to disassemble the computer laptop everything and now I have the screen and the top cover out as well. I don't know how to remove the display frame to remove the hinges.

  Can you please help me with this!

  Thanks in advance!

  Hello

  Well my friend, in my opinion you should not try to disassemble the laptop if you n t have the necessary experience and don t know to do this!
  You could damage other parts that you know

  You're stuck on the LCD mask?
  As far as I know the LCD mask is covered by two screws that are hidden under the joints.
  You will need to remove both seals of mask LCD, and then you could remove the two screws hidden under the seals mentioned.
  Then, you could put your fingers between the mask and the LCD screen in order to release the LCD mask plastic locks.

  But note; Be careful, don't use any force!

• Portege M400 - how to remove the condensation of water?

  I received a second hand toshiba portege m400 mail and saw there probably a condensation of water trapped between the external display and touch screen behind her. because the screen in the upper left corner looks whitish. and the sender of the laptop said he wasn't there when he sent it. I have a picture of trapped moisture, for those who want to see it.

  so, I opened the screen by unscrewing. and I saw that most of the moisture is stuck between the external screen glas and one other layer behind him, which I guess, is the part of the touch screen. who looks inaccessible. These 2? the layers form the upperpart of the screen.

  the lcdscreen with all the electronics in this layer, form the lower part of the screen or if you want, cover. This part is now oke. He also had a condensation of water on it and I was able to gently wipe the little moisture of the lcdscreen without problem. This helped a bit with this problem.

  but moisture remains trapped between the part of the touchscreen layer and this layer of glass in the upperpart of the screen/cover.

  hoping to evaporate the moisture, I left the enlightened a bit more open for a day, I broke even the upperpart and the lowerpart of the screen. I applied a little of an infrared lamp, a remote backup heat. anything that did not help.

  * so, how can I remove the condensation of water? *

  * is there a way to remove a layer in the upperpart of the screen to reach the humidity? *

  Hello olekike

  Please don t get me wrong, but I'm afraid, you need professional with this Mr. help as I see that your question is not answered for days now, and I think that nobody here has a lot of experience with this stuff.
  View replacement OK but how to remove the condensation of water on the touchscreen is perhaps too heavy for us.

  I recommend strongly to contact the nearest Toshiba service provider and ask for help. talking with the guys what we can do about it.

• How to remove the DVD ROM on the Satellite L300D 242?

  Hello

  my laptop (* Toshiba L300D 242 *) DVD ROM has been damaged and I have acquired a new and now I can not figure out how to remove my old DVD ROM and replace it with a new one... Please help me understand how to remove the old and replace it with a new one...
  Thank you...
  E-mail: [[email protected]]

  Agree with Feliks the ODD is secured by a screw hidden in the HARD drive Bay.
  So the HARD drive Bay cover must be removed to access this screw procedure is not really difficult, so you should be able to remove it easily.

• Satellite Pro 4260: How to remove the DVD drive?

  I have a 4260 Pro Satellite and it seems that the DVD drive is broken and I want to replace it. I can't figure out how to remove the old.
  Does anyone know how? Is there a manual with available how?

  Thank you

  Hello

  This notebook is not know for me but has checked some sites on the net and it seems that the top cover must be removed.
  Then lift the CD-ROM/DVD-ROM drive to disconnect PJ700 on the CD-ROM/DVD-ROM of PJ15 card on the system board.
  Remove the two screws that fix the Board Connector CD-ROM/DVD-ROM.
  Separate the brace connector connector Office CD-ROM/DVD-ROM and CD-ROM/DVD-ROM CD/DVD-ROM drive

  Well, I think that it of not easy for a person without experience.
  So if you n t know how to do and you have without much experience you should ask someone how knows what to do ;)

• Satellite Pro L100 - how to remove the keyboard

  I have a L100 which has been "sprayed"... don't ask...

  How to remove the keyboard... ideas please

  see you soon

  Bob

  Hello Bob

  The keyboard replacement procedure is almost on all Toshiba laptops. At, first of all it must remove the cover above the keyboard (where the buttons are placed).

  After doing this to remove the keyboard is very easy.

  BTW: is your laptop under warranty? Please be careful about this.

• Z500 how to remove the battery?

  
  

  Hi Flory2011,

  Len mentioned the Maintenance Manual material that is found on the link below...

  http://download.Lenovo.com/consumer/mobiles_pub/lenovo_z_p_series_hmm_v1.0.PDF

  You can also watch online tutorials on how to remove the bottom cover and the battery at this link in the section FRU...

  http://service.Lenovo.partner-management.com/content/CourseWarePublic/18359/player.html

• P645-MG how to remove the battery? I push with a paper clip in the hole of the icon on the back, but no reaction

  TravelMate P645-MG how to remove the main battery? Nothing happens when I push with a paper clip in the hole of the battery icon at the back of the computer. A video UTube said that a cover opens, but I can't find where there is a cover of the battery compartment.

  Hello

  Your laptop is equipped with an internal battery. You need to remove some modules and the bottom of the laptop to have access to it. The pinhole is only to reset the battery.

• How to remove the lid of the scanner on the Photosmart 5520?

  Manual to insist that the lid of the scanner of the Photosmart 5520 (model #CX042A) can be removed.

  When I try however, it does seem it Peel, as if a force is applied over it feels like it will break.

  I contacted HP technical support per session chat, and after about half an hour the technician finally dropped and referred me to the store where I bought it.  I went to Office Max, where I bought and asked them.  They were also puzzled with a right to the camera in front of us, they could not figure out how to remove the cover.  They were also afraid to break if they tried to remove it.

  Are there instructions indicating how to remove it so that the lid or the hinge is not destroyed in the process?

  The manual is not wrong.  You can remove the cover on a 5110.  I was just trying to do the right way the first time.  This post told me how to do it.  As far as I know, the only things that have changed since the 5510-5520 are the firmware and internal control.  The shell of the printer must be roughly the same.

• ST2220T repair? How to remove the shell back and standing?

  Hi all

  I just took my beautiful ST2220T and I need to remove the stand in order to have the screen adjustment / layout that I need. I tried to find a service manual, or some instructions on How to remove the back cover. I have a lot of experience with the hardware, and that's why I'm looking for it :) Because each new device has some trick in his bag and I really don't want to accidentally do something I might regret later :)

  Thus, any help is very appreciated :)

  Thanks in advance,

  Voja

  Cave of dwarf,

  Dell does not open any monitor to fix them. We will send them the manufacturer to do this kind of work. This is why we do not have any "Service Manuals" for Dell monitors. The ST2220T is not designed by us to have the base and back cover. Any damage caused while attempting this is not covered by the standard Dell warranty.

• How to remove the extension AM and substitution of the server

  Hello
  
  Can someone tell me please how to remove the possibility of existing substitution and expansion of the AM of the server.
  
  Concerning
  Swati

  Swati,

  You can remove the substitution using the API jdr_utils.deletedocument ('').
  The path will be as "oracle/apps/ap/xx/customizations/0/server /...» »

  Kind regards
  GYAN

  Published by: Gyan on June 3, 2011 19:28