HP 15-AC044TU: how to enable the wifi/connection wireless network in my laptop HP 15-AC044TU win-7 64-bit

Similar Questions

• Satellite C660 - 15K - how to enable the wifi module?

  Laptop has no mechanical switch the WiFi module.
  What utility or driver must be installed to enable the WiFi module?

  Network adapter driver installed with no problem, in the properties of the computer module is active and active, but does not see available networks.

  Assistant to Toshiba at the same time said that the module is disabled...

  Help, please!

  > What utility or driver must be installed to enable the WiFi module?
  You must activate the Wlan using FN + F8 key combination.
  Have you tried that?

  If this does not work, then you must install the VAP (value added package) and utility support Flash Card that controls the keys FN.

• Satellite P10: How to enable the WiFi of Intel 2200BG card

  Hello

  I have a psp10e Satellite that I recently installed a WiFi of Intel 2200BG card. After having problems to light up I put the Ribbon on the PIN 13 on the map to turn on the radio.

  I have installed all the latest drivers / BIOS updates and spend hours searching the Internet I am still yet to find a cure for the hardware switch/fn + f8 and the WiFi led to work.

  Is there something that everybody has understood to make the switch/led work material? There must be a better remedy than a piece of duct tape! It is the BIOS that has nothing to do with the hardware switch?

  Hello

  You isolated the correct pin code? With the 13 PIN is pin 7 when you look at the map. And unfortunately there is no biosupdate for these machines, because everything is 'wired', then you will need to follow the alternative route...

  Sorry man

  Welcome them

• How to enable the AHCI for SSD on M6-1010TX laptop computer HP

  HELO

  Have tried to install an EVO of 840 Samsung 240 GB SSD on my laptop of M6-1010TX with WIN7x64 i5/4 GB and running.

  The SSD seems to work OK, but I when I run Samsung magician this is a warning that it must be set to AHCI.

  Also, most of the menu items are grayed out and unavailable in Wizard, so I can't see or adjust all parameters. I don't even know if the TRIM work.

  There is no possibility of setting to AHCI in the BIOS. (In fact there is no provision for seting pretty much anything in the BIOS)

  I've seen a remedy to a similar problem on this forum under 'How to enable AHCI for HP ENVY TouchSmart m6-k015dx Sleekbook' which offers to upgrade to the latest version of Intel RST, which is supposed to give favor SSD attitude to go with the 7 series Intel chipset.

  I already have the updated HP version of installed RST (2012-05-04 11.1.0.1006), but the Intel site has versions up to 13.1.0.1058 in date 27-05-2014.

  Anyone know if these later versions of Intel are safe to install?

  PS - I 840 Samsung SSD EVO running on 2 HP ProBooks's a little older, and they run like lightning.

  A simple setting in the BIOS to enable the AHCI is available on these. Why not in the new M6?

  Thank you

  OK Hüffer---> we have a update

  I had the opportunity to re - install the SSD drive this morning.

  It seems that you were mostly correct, but there is also a bit of a conflict between the Samsung software and HP hardware.

  When I re-installed this time I connected the SSD in USB BEFORE installing the software (Samsung instructions say to connect AFTER insalling software). This has resulted in much better recognition of the SSD and all the options are now available in Sasung magician.

  EXCEPT - 1. He always warns AHCI mode being "Deactivated (IDE or RAID).

  2. it does not recognize the SATA 3 Interface

  HOWEVER - it seems to work quite fantasmagorically FAAAAAAST

  Samsung Benchmark gives random read/write speeds about 30% above their maximum rate quotes

  These reference speeds are about double what I get from the above, 2 HP ProBooks who have SATA 2 interfaces, so it seems that the SATA3 interface actually works correctly.

  I am now very happy with this performance (but I wish that AHCI warnings were not there)

  So the secret seems to be to connect the SSD drive first and do believe not all alerts when the evidence says it actually works OK.

  Thank you once again to Hüffer,

  Hawkeye

• How to share the WiFi connection between Mac (host) for XP (comments)?

  Hello

  When my Mac is connected to an ethernet cable, I am able to share the connection with my XP VMWare (bootcamp).

  Now I use a WiFi connection and I can't get a connection when you use NAT or bridged in VMWare network settings. Help please?

  Restart the Mac and then without starting the merge run the following command in a Terminal (/ Applications/Utilities/Terminal).  Just copy and paste the command and press ENTER.

  kextstat | grep vmware; ps -ax | grep vmnet
  

  The output should be similar to the following.

  $ kextstat | grep vmware; ps -ax | grep vmnet
  327    0 0x34962000 0xd3000    0xd2000    com.vmware.kext.vmx86 (2.0.2) <12 6 5 4 2>
  328    0 0x34223000 0xb000     0xa000     com.vmware.kext.vmci (2.0.2) <6 5 4 2>
  329    0 0x3422e000 0x6000     0x5000     com.vmware.kext.vmioplug (2.0.2) <41 21 6 5 4>
  330    0 0x342ca000 0x9000     0x8000     com.vmware.kext.vmnet (2.0.2) <12 6 5 4 2>
  12815 ??         0:00.01 /Library/Application Support/VMware Fusion/vmnet-natd -c /Library/Application Support/VMware Fusion/vmnet8/nat.conf -m /Library/Application Support/VMware Fusion/vmnet8/nat.mac -d /var/run/vmnet-natd-vmnet8.pid vmnet8
  12821 ??         0:00.00 /Library/Application Support/VMware Fusion/vmnet-dhcpd -cf /Library/Application Support/VMware Fusion/vmnet8/dhcpd.conf -lf /var/db/vmware/vmnet-dhcpd-vmnet8.leases -pf /var/run/vmnet-dhcpd-vmnet8.pid vmnet8
  12823 ??         0:00.00 /Library/Application Support/VMware Fusion/vmnet-netifup -d /var/run/vmnet-netif-vmnet8.pid vmnet8 vmnet8
  12826 ??         0:00.00 /Library/Application Support/VMware Fusion/vmnet-netifup -d /var/run/vmnet-netif-vmnet1.pid vmnet1 vmnet1
  12829 ??         0:00.00 /Library/Application Support/VMware Fusion/vmnet-dhcpd -cf /Library/Application Support/VMware Fusion/vmnet1/dhcpd.conf -lf /var/db/vmware/vmnet-dhcpd-vmnet1.leases -pf /var/run/vmnet-dhcpd-vmnet1.pid vmnet1
  12831 ??         0:00.00 /Library/Application Support/VMware Fusion/vmnet-bridge -d /var/run/vmnet-bridge-vmnet0.pid vmnet0
  12904 ttys001    0:00.01 grep vmnet
  $
  

  What does your show?

• How to extend the Airport Express Wireless Network at guesthouse?

  Currently have an Airport Express (fairly new, updated). Centrally located in my house.

  I have a guest house which has a garage and a front door door aside.

  Guest House is about 56 feet from the main house.

  I can get the wifi outside, (4 bars) up to 3 feet of the guesthouse before he gets spotty or the connection is lost.

  If I go into the Guest House, I see the other neighbors networks, but not my own. (Signals strong, 4 bars).

  My question is: How can I extend the range of my network wireless in my guest house? If I need another Terminal Airport Express?

  Where would he put regarding my 1st Express?

  I would appreciate comments, thank you.

  As a first step, it may be good idea to test the different locations of the existing base station. Temporarily connect an Ethernet for inbound Internet cable. Try moving the base station to various locations. Avoid stray objects/structures (Wi - Fi and Bluetooth: potential sources of interference wireless - Apple Support).

  If necessary, an extension of the network (Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo...) are possible. The best way to do it would be through an Ethernet connection to the extended base station (placed in the main, if possible). Alternatively, you can test whether a link of powerline network adapter could be used instead of an Ethernet cable to the extended base station.

• How to disable the auto connect wireless in windows 7

  every time I turn on my pc it connects to the WiFi automatically, I want to know how to disable this option, I want that it ask me to put the password key to connect to my wireless network, at the same time that it always automatically connect pls give me the solution to this...

  for the first time that I have connected to the wireless network, he asked me to put in the password to connect, now everytime I turn on the computer it connects to the net without prompt to put me in the authentication key...

  Go to control panel > all items in the control panel > network and sharing Center > manage network wireless (in the left pane) and right click the one you want to change, and then click Properties > tab connection.

  There are three fields that can be changed: automatically connect when range, connect to a more preferred network and connect even if the network is not broadcasting. Change them accordingly.

• Satellite L510 - how to install the driver for wireless network card?

  Hello

  I recently bought Toshiba Satellite L510 laptop and problem in the installation of the wireless driver. I downloaded the driver from Toshiba sites.
  And installation get competed with success but it always ask for divers 'Network controller' and 'Askey for Toshiba.
  I'm trying different drivers of these last two days, but without success.

  Can someone Guild me please how to configure computer L510 laptop wireless. Also where can I get the drivers mentioned above.

  Thanks in advance.

  Hi mate,

  I m asking you to install the WLAN driver on your laptop computer purchased recently. Normally all the stuff is already preinstalled the operating system with all the drivers and tools. He s ready to use.

  However, what you mean exactly with her always ask for divers to Askey Toshiba network controller?

  Your wireless network card is listed in the Manager device correctly or yellow exclamation? What WLAN card you have?

• How fast is the Atheros AR5007EG wireless network adapter?

  I have an Atheros AR5007EG wireless network adapter in my computer. For six months, we have Broadbank 100Mbit/s in our House. When I call the support (support of the broadband company) they ask me to check if my computer can handle it. How can I check that?

  I think the Atheros AR5007EG is a 802. 11 b / g device. Which would have a maximum speed of 54 Mbps.

  For 100 Mbps, you need a Wireless N - 802.11n device.

• Satellite L500 - how to enable the WLAN?

  I replaced a hard drive of mine (L500 PSLS0A - 08 p 002) and I installed Windows7 64 bit on it.
  I used to market its WIFI by pressing the FN + F8 keys.
  But now I can't on it using the method.
  I downloaded its end drivers.
  In reality its all the function keys do not work.
  Please let me know how to enable the WLAN and function keys.

  Hi kim2kjy,

  You have installed Windows 7 Toshiba or normal Microsoft disk recovery disk?

  The FN keys to install Toshiba Value added Package, and Flash Cards Support utility. These two tools can be downloaded on the official page of Toshiba.

  Check this box!

• Equium A110-252: how to enable the wireless function?

  Hi, first time ive been on this forum. I recently bought the toshiba satellite (think that's the spelling) and a wireless router. now, the router works well with my other computer, is very fast, but I can't go online with the laptop. all the info I get, is that the wireless is not activated? its got beat me, so I hope someone out there can help me to solve the problem, so I can start using my laptop in the room. Thanks in advance. Susi

  Hello Susi

  The first use of WLAN switch and move it to THE post. The WLAN control light should be on. After this check in If Device Manager card is correctly registered.

  The last step is to use the FN + F8 key combination to activate and enable the wireless network adapter. When activated the WLAN connection must be configured correctly. I assume that your camera comes with WLAN client utility. If you use this utility to configure the WIFI connection, please ensure that this WLAN Windows option is disabled.

• How to enable the continuation of the Standby Option for a USB mouse: I do not see the "allow this device to wake the system from standby mode' check box__

  I use Windows XP Home Edition and I am fully up to date with the latest version of the software.

  I would like to activate my mouse USB power out "sleep mode" on my computer.  I found the help topic that describes how to do this: http://support.microsoft.com/kb/280108 how to enable the continuation of the Standby Option for a USB mouse

  However, when I follow these steps, I don't see the 'allow this device to wake the system from standby mode ' check box on any of the windows as described in the documentation for Ms.
  I use a Microsoft Comfort Optical Mouse 3000 (IntelliPoint) USB

  Any help would be greatly appreciated!

  This gives a test:

  1. click on START
  2. click on 'run '.
  3 type "notepad" (without the quotes) and press enter
  4. copy and paste this into Notepad:

  Windows Registry Editor Version 5.00

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\usb]
  "USBBIOSHACKS" = DWORD: 00000000
  "USBBIOSx" = DWORD: 00000000

  5. click on file > save as
  6. change the dropdown to "all files".
  7 type usb.reg as the file name and save the file somewhere easy to access
  8 go find the file and double click it. Confirm that you want to add it to the registry
  9 restart the computer and see if you can wake the system from standby mode

  For reference, take a look at this:
  http://www.dslreports.com/Forum/r19635912-missing-power-management-tab

  Let us know,

  Thank you!

  Ryan Thieman
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to enable the automatic configuration service in Windows XP

  How to enable the automatic configuration service in Windows XP

  Hi SamuelOkon,

  Are you facing any problem on your computer?

  You can follow the steps in this link & check if it helps.

  How to activate the Wireless Auto Configuration startup type?

  Hope the helps of information.
  Please post back and we do know.

• How to put a WIFI-connect button directly on the home screen?

  Hi all

  I know there is a wifi - connect button in the notification Panel, but I have to turn on my screen, open the Control Panel, then click on the "quick settings" button, then click on the WiFi connect button... " 4 actions connect within my own wifi network!

  (Note that I don't want the automatic connection setting because I don't want to be connected to each time)

  I wish I had just a "wifi - connect ' on my screen which allow me to connect just by clicking this button."
  I can't find a widget or application in my phone to do this.

  Do you know how?

  Thank you very much
  Guy

  Hello

  The best thing would be to follow the advice of dandy63of s, by downloading a third-party application that can handle it. The closest you can get this as standard (without having to download any third-party application), would be to add a shortcut to settings > Wi - Fi. This can be if you long press on an empty space on your home screen > select Apps > shortcuts > settings > Wi - Fi.

• How to enable the ReadyBoost feature?

  I would like to know how to enable the ReadyBoost feature.

  Does anyone have any suggestions?
  Thanks in advance for your suggestions

  I would like to know if it is possible to assign an SSD internal to do this instead of using a USB drive or not.  I tried ReadyBoost option in SSD drive is not available.

  Do you have any suggestions?
  Thanks a lot for your suggestions :>

  Hello

  Sorry, but you cannot use an internal hard drive for ReadyBoost. Indeed, an SSD can not use ReadyBoost.

  This feature can use a USB flash drive external as a hard drive cache to improve the disk read performance.

  More information on the following links.

  Understand the ReadyBoost and the question of whether it will Speed Up your system
  http://TechNet.Microsoft.com/en-us/magazine/ff356869.aspx

  Turn ReadyBoost on or off a storage device:
  http://Windows.Microsoft.com/en-us/Windows7/turn-ReadyBoost-on-or-off-for-a-storage-device

  Concerning