HP 4530 s, Win7 64 bit, Hp protect tools does not not on any browser except Internet Explorer

Similar Questions

• Win7 64 bit freezes & arrow function does not work, do not click to navigate anywhere

  Win7 64 bit PC crashes & arrow function does not work, do not click to navigate anywhere, exceptionally after being on ~ 2 + hrs. I can only turn off by pressing the power switch for about 5 seconds.

  Hello

  You did changes to the computer before the show?
  
  Method 1
  Step 1: I suggest to start the computer in safe mode and check if the problem persists.
  
  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2:  If the problem is solved in safe mode, then I suggest you perform the clean boot and remove the program that is causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: Follow step 7 clean boot KB929135 article to reset the computer in normal mode.

  Method 2
  I suggest you try the steps from the following link:

  Optimize Windows 7 for better performance
  http://Windows.Microsoft.com/is-is/Windows7/optimize-Windows-7-for-better-performance

  Also provide an observer event logs.
  Open event viewer
  http://Windows.Microsoft.com/en-in/Windows7/open-Event-Viewer

• Portege M750 Win7 64 bit Wireless Manager (3G) will not work

  I can't TOSHIBA Wireless Manager (3G) to work in a new installation of Win 7 64 bit.

  I did a test installation of Windows 7 64 - bit on and old SATA hard drive and checked TOSHIBA Wireless Manager would work. He did.

  I then did a fresh install of Windows 7 64 - bit on a new Crucial C300 Real SSD 256Go.

  The new facility with the Crucial SSD is not very successful... The operation "stop and restart" does not - the closing not always power off completely and you must push the switch down to.

  Sometimes the SSD does not start - you enter the password of the BIOS but then nothing happens. Sometimes you turn off the power and remove the battery before as the startup disk.

  But the biggest problem is that the (3G) Wireless Manager will not work. The application opens and indicates that "died" - which it is impossible that I use WiFi to post this question.

  I tried to install the software Vodafone 3 G portal. It detects the presence of the 'mobile device' (SIM in housing) but then can not turn it on.

  I downloaded and installed all the latest drivers for the chip, the pilot 3G, 3G software, LAN driver, LAN software and all updates of Windows 7.

  I have the latest version of the BIOS (3.0) but this has not been updated by Toshiba since 11/04/09.

  I would point out that Diagnostic PC Toshiba tool does not recognize the installed 8 GB memory (but ccleaner):

  Model name PORTEGE M750
  Part number PPM75E-00N017EN
  Version of the OS Microsoft Windows 7 Home Premium 6.1.7600
  Version of the BIOS Version 3.00
  Processor Intel (r) Core (TM) 2 Duo CPU P8400 2.26 GHz
  Physical memory 4096 MB RAM
  Disk capacity hard 256,052,899,840 [bytes] 238.468 [GB]
  Network Intel(r) 82567LM Gigabit Network Connection = 10.0.2.2 version = MAC address
  TOSHIBA F3507g Mobile Broadband Network Adapter version 1.3.0.9 = MAC = address
  Version of Intel(r) WiFi Link 5100 AGN = 13.4.0.9 = MAC address
  F3507g Mobile Broadband Modem Modem TOSHIBA version = 5.24.3.0
  Internet Explorer 8.0.7600.16385

  This indicates a BIOS problem?

  -don't

  points to a problem of firmware on the SSD drive (is it sandforce) torque to the incompatibility of BIOS of the SSD.

  I assume that all drivers installed etc were identical on the installation of the trial of HARD drive? so if this is the case it must be the SSD does not not with the BIOS correctly, so the other issues as well

• Satellite P305-S8997E: cannot switch to Win7 64 bit - error: your system is not there to upgrade

  Hello world.

  I have the Toshiba disk for Windows 7 Home Premium Upgrade, as I'm currently running Vista Home Premium 64 - bit.

  I do not choose the path of upgrading with the upgrade wizard Toshiba 64 bit version.
  However, I am stunned with the Toshiba Upgrade Wizard dialog box, saying: "your system is not applicable to the upgrade. You can see http://www.csdsupport.toshiba.com/tais/csd/support/windows7upgrade/ information Windows 7 upgrade"after he checks the first 4 criteria as being correct.

  Any help would be appreciated.

  I did buy my notebook of the USA, but live in Australia. However, I was able to order the disk to upgrade Windows 7 from Australia when I arranged for my laptop model to add to the eligible improvements on the website.

  For more information, I was able to get my hands on a disc of Windows 7 Ultimate 64-bit full version. On this basis, I chose Windows 7 Edition Home Premium than the version I bought.
  I have used my product key from my Windows 7 Home Premium Upgrade disc and chose the upgrade version.

  There are 3 the memory usage possibilities that are incompatible with Windows 7 so I uninstalled them and used the Toshiba Windows 7 driver updates to install what I could. Everything works fine and update MS naturally recognizes the genuine key.

  However, it defeated the purpose of why I can't upgrade from upgrade disc.

  Thank you.

  Hello

  Did you use the preinstalled Toshiba Vista OS until you used the Windows 7 upgrade disk?

  How about a new installation? This should be possible as well Win 7 Toshiba drivers can be downloaded from the Toshiba driver page we

  Welcome them

• Vista 32 bit Toshiba Power Saver does not work - Satellite L300 PSLB0E

  I have problem with Toshiba power saver - it does not work.
  I have not found a driver for Vista 32 bit here.

  Toshiba Satellite L300 PSLB0E-04R012RU VISTA HOME PREMIUM

  Thanks for your help

  Hello

  What do you mean with it does not work?
  What energy savings you used?

  The Vista operating system uses clean power options and there is no special Toshiba Power saver for Vista as for Win XP

  Maybe you tried to install the saver of energy for Win XP?

• Win 7 64 bit HP recovery CD does not work

  Hi all

  I ordered the HP Windows 7 64 bit recovery CD and it doesn't work.

  When it separates partitions, and it displays its progress as usual for example

  1/7 full
  2/7 full
  3/7 full (files copied etc..)

  but around 3/7 or 4/7, the sound of the CD in road changes and it seems that it restarts continually.

  I am confident that the problem is related to this CD because the other disks work properly and the 32-bit recovery CD, I had with laptop computer reinstalled Windows very well.

  I wonder what could happen? I have contacted the company on this topic and am waiting to hear. I see no damage to the evidence on the record, and I take great care in general. All I know is it does not work. Any ideas?

  Thank you

  > I ordered the HP Windows 7 64 bit recovery CD and it doesn't work.
  What do you want with a HP recovery disk?
  If you have a Toshiba laptop, then you must use a recovery disk Toshiba

• HP Scanjet 5590: Scanjet 5590 & Win10 64-bit - install and scanning does not work

  1 install the latest official software for Scanjet 5590 stops in the Middle after the first component (software scanjet 5590) before TWAIN / Iris etc. Macromedia window remains opent "Please wait" but the 2nd part of the installation process does not start.

  2. no doubt as a result no scanninng. Before the scanner buttons not working do not (missing twain) and scan from the software installed launch the scanner (activate powersave); Opens the window of the software, but analysis does not start.

  Win10 64-bit; USB. HP CP1025nw the wireless is the other HP product installed. ASUS z97 MB, i7 - 4790 k / 16GB, SSD.

  I tried and does not work:

  -different, another USB port USB cable

  -new installation of 64-bit Win10

  -a lot of removing the software and driver (windows install cleaner, file removal, registry) and reinstall

  -HP support assistant/framework/scanning, printing doctor [result "don't install the driver" awhile, but obviously it is installed and the wizard fails to resintall it]

  Installation of the software in safe mode (after editing registry it is possible) all the complete component installs (scan software, iris, twain, etc.) but always the same questions: scanning does not work.

  Any idea or suggestion?

  OK, here's the solution that works for me:

  YouTube

  In brief

  -check out you the shape of the package files (winrar will be required)

  -HPZstub.exe (NOT run Setup.exe)

  problem solved...

  I went two hollow guidance package and remote session with support and got this link after my file submitted in support of the L2.

• Satellite C850D-115 / Win7 - key mode special funktion ist does not

  Hello

  key mode special funktion ist does not, but I've tried everything in the Bios and software "Toshiba hardware configuration utility".
  I still need to press on "FN +" to use the special function keys, while active bios mode!»
  Special function mode was never working, I have no more ideas. You...?

  As far as I know using Win7 you must press FN every time when you want to use the FN keys. There is just to Win8 option to change that and use the FN keys without maintaining the FN key.

  > Special function mode was never working...
  Maybe stupid question now but what do I say with special function mode?

• Vista Business 64-Bit with AutoCAD 2009 does not seem to use all 8 GB of RAM available.

  A workstation newly built (S5000XVN Intel / Xeon / 8 GB RAM / 2 GB RAM video) with Windows Vista Business 64-bit is used with AutoCAD 2009 (64-bit).  The workstation hangs under stress, apparently because not enough RAM is available.  ("Stress" is "Turning entirely made of a certain complexity 3D drawings")

  The Task Manager / Performance tab indicates never to use RAM above about 3.25 GB, even if ten or more concurrent applications are loaded, including IE 8 (6 graphically heavy windows) and AutoCAD with 6 or more complex drawings open at the same time.

  There are two issues, I think:
  1. in the event that a busy workstation indicate use RAM above the 32-old bit of 3.2 GB limit?
  2 are there MS Windows Vista settings that are necessary to ensure the use of RAM available?

  Thanks in advance.

  Thanks for the reply.

  I studied the installation of AutoCAD 2009.  It's actually the 64-bit version that is installed, and the Task Manager reports it as a 64-bit application when it runs.  (In other words, it is not marked as a 32 bit application.)

  I must admit that I no longer believe that the machine is running out of resources or do not use all the resources available to it.  We tested the machine by throwing 18 complex, fully rendering the 3D drawings within the Academy, in addition to two cases of IE 8, three instances of Explorer Windows and MS Windows Mail.  Use of the RAM did climb, reaching finally the 4.06 GB, clearly indicating that the 32-bit 3.2 GB limit has been exceeded.  It seems that just drawings don't take up that much RAM.  BTW, there was no increase in the paging activity that I could see.

  However, the application does not seem to be frozen or looping when the client attempted to turn one of the drawings.  The CPU on the two wires (Xeon processor) usage increased to 55% and remained there. the State of the process, as reported by the task manager went to "Not responding" and stayed there; and the display of the image froze on an empty workspace, with a three seconds flash drawing on every 20 seconds.

  So: It now seems that there is a problem with AutoCAD, not a Vista problem.  I would appreciate comments, however, if you think that this analysis is wrong, incomplete or based on wrong assumptions.

  Thanks for your help.

• How to get a hp 4600 Color Laser jet print on a vista or Windows 7 64 - bit OS PC which does not have a parallel port connection?

  My hp 4600 color Laser Jet uses a parallel cable to connect to a Windows PC. When I had XP as the OS it worked fine. But now after the upgrade to Vista or Windows 7 64-bit OS it will not work and my PC does not even recognize it when it is plugged into the PC with the parallel to USB cable that worked so well before. So, what should I do to get the PC to recognize the Hp 4600 and have it printed again as before? (My first plan is to try to get the printer to work by hooking up through Wireless. Does anyone know if it will work? I'll answer my own question, if it does. Wish me luck! (Thank you!)

  According to the HP support site, there are drivers available for Vista and Windows 7 If you're lucky it. Download the appropriate drivers for your computers. According to the information of product from HP, this printer can be connected directly to the network by an ethernet cable. I don't see where it has wireless capability, but in any case ethernet is preferable for printer connections if possible.

  Connect the printer directly to your router or switch connected to your router and assign a static IP address outside the range the router DHCP. Then, install the drivers that you got from the HP website for your operating system.

  MS - MVP - Elephant Boy computers - don't panic!

• Windows 7 64 bit, Windows Media Center does not work

  After you activate Windows Home Server media sharing, I went to my 64 bit Windows 7 machines and tried to launch Windows Media Center.  After you run through the configuration of the connector of WMC, reboot, and then clicking Windows Media Center, I get:

  "Windows Media Center has stopped working".

  He said that it is looking for a solution, but after a few seconds, he goes and does not return.

  I never have a chance to fix anything, or even see if it connects or not.

  Any ideas?

  Hello
  Reinstall the WMC and should resolve in most cases.
  1 open the control panel-> programs and features.
  2. click on Turn Windows features on or off in the left pane.
  3 expand the multimedia functionality, turn off Windows Media Center. Click Yes to continue, and then click OK to exit. Then restart.
  4. open features Turn Windows turn on or off again. Functionality in Windows Media Center. Restart the computer.
   
  5. launch Windows Media Center, initialize the program.
  $C

  God will not look you over for medals, but for scars. Each winner has scars; I do this either on the same heart

• 16-bit data base software does not communicate with NT4 server on the windows computer 7.

  We are a small manufacturing company. I installed old software database (16 bit) on windows 7 (64-bit) a year earlier. This software has worked for a few months and then it stop working. Database software still works on the old xp based computers, but it does not work on my windows 7. We believe that this database software is not communicating with our windows NT4 Server. It could be the update of windows 7, but we're not sure. I contact you because this database software is worked for two months on my computer and then suddenly stop working, it's strange, and now I am not able to install again. So is there someone who can suggest me what would be my next step.

  Windows 7 64-bit is not a 16-bit subsystem or a way to install the NTVDM extension that supports. You need to install a 32-bit version of Windows 7.

• Inspiron N5010 windows 7 64 bit driver driver Wireless does not

  Inspiron 15 Intel (N5010)

  After buying a new hard drive for my laptop and reload windows 7 home premium 64-bit, I started to download the proper drivers, most of them seems to work, except for my wireless adapter which does not pick up.

  I tried the site of dell support for drivers on this list don't seem to work either, I finished downloading the drivers as I can, as I do not know the brand of my card and my knowledge of the material is very limited.

  Please please help with the right drivers for my problem thank you very much.

  pharoah165b,

  When you reinstalled the operating system, have you installed the desktop system software / laptop (as appropriate) and drivers from the chipset first? If this is not the case, the rest of the drivers will not install. How to download and install drivers in the correct order

  Start with the computer system software and the chipset drivers and follow the list.

  Rick

• Hi, I installed a set of creative cloud including Adobe Acrobat Pro (64-bit Windows)... does not work

  I have a Windows 64 bit HP laptop that I removed and installed several times a CC package which includes PS, Illinois, LR, InD and Adobe Acrobat Pro.   Everything installs fine and works fine except for

  Adobe Acrobat Pro. For somereason it says it is installed but it does not appear when I try to find it.   In the programs, it shows as installed but it does not appear with the appropriate icon of Adobe.   It's as if there is a problem of copatibility.  Ideas?

  Hello

  I have corrected the problem.   Apparently with the subscription of creative cloud the

  Adobe Acrobat Pro installs the same way other products

  install.  Once downloaded the package you have to go the

  'Exceptions' folder which is part of the generation and install it then

  it.

  Thank you

  Ellen

  Friday, February 27, 2015 at 10:31, screen name of Test [email protected]

• Global Script Protection activation does not work when you add '& '.

  Hi all

  To prevent crosssite scripting attacks I ticked the checkbox 'Enable Global Script Protection' in the admin CF. But it doesn't work, I mean not able to prevent the attacks by scripts.

  I followed steps

  1] I run the below URL.

  https://xyz.ABC.com/index.cfm?cardholder_number= & < script > alert (1) < /script >

  [2] fornt ultimately I got a javascript alert message as injected into the URL.

  But this alert message should not be that I activated the script protection in CF Admin. law?

  Now, I have removed '&' (https://xyz.abc.com/index.cfm?cardholder_number= < script > alert (1) < /script >) since the above URL then I wasn't getting the javascript alert message. Does that mean that protection of script will not work if we add '&' to the URL?

  I searched the neo - security.xml and its looks like below.

  < var name = "CrossSiteScriptPatterns" > < struct type = 'coldfusion.server.ConfigMap' > < var name = '& lt; \s*(object|embed|script|applet|meta)' > < String > & lt; InvalidTag < / string > < / var > < /st ruct > < / var >

  Can someone help me solve this problem.

  Abdul L Koyappayil says:

  But even when a remnant of doubt why alert message is coming when there is '&' in the URL?

  This happens with "&" because it is a symbol special "Javascript" whose purpose is to delimit - i.e. separated - value of the URL query string key-value pairs. For example, in the URL www.myDomain.com/index.cfm?a=1&b=2, the '&' defines the query string in the key-value pairs 2

  a = 1

  b = 2

  Consider the case where the URL is www.myDomain.com/index.cfm?cardholder_number=& then . The & will delimit the query string in

  cardholder_number =

  The presence of '&' implies there are 2 variables. However, there is that a single sign "=", which means there is only a pair of key / value. In addition, cardholder_number is a name for a URL variable, while is not. The browser then sends the query string next to your application

  cardholder_number = EMPTY_STRING &

  However, Coldfusion's scriptprotect feature will intervene and this to neutralize

  cardholder_number = alert (1) EMPTY_STRING &

  that is harmless. These will come into Coldfusion variables URLS

  cardholder_number = EMPTY_STRING

  EMPTY_STRING = EMPTY_STRING

  The special nature of '&' as delimiter is what drives the browser to run the script. Indeed, by default, browsers will run any Javascript you place in the query string. Running, for example

  http://www.myDomain.com/index.cfm?

  But why tell I if they ask me why javascript alert then.

  As you have seen, the

  This isn't the case here.