Portege M750 Win7 64 bit Wireless Manager (3G) will not work

Similar Questions

• internal card reader must be disabled and then enabled in before Device Manager it will not work properly.

  Whenever I start my computer, my internal card reader must be disabled and then enabled in before Device Manager it will not work properly. I put an SD card in there and auto does not work. I check my computer and it shows that it is there, but when I double click on it to open it I get a message saying: Please insert the SD card. When I go to Device Manager and disable and enable fine orks. I tried different cards, but it makes no difference.
  I installed a different card reader, but another did the same thing. This leads me to think it's a matter of Windows.
  I tried to do a repair install, but it ends and said that the upgrade has failed?
  Anyone have any ideas on how to solve this problem.

  I am running Windows 7 Pro 64-bit. It is a Renesas controller and I use the 2.1.28.0 with firmware driver 4015.

  I'm not sure but I may have found the problem. I see where a guy here was having a similar problem and it was caused by Acronis. I recently installed Acronis 2012. I have been lucky to uninstall, but I will update this post when I do.  He was also running windows 7-64 bit on a motherboard ASUS!

  Acronis was the problem.  I uninstalled Acronis and now my card reader works as it should.  Strange!

• Portege M750 and Win8 - metro and touchpad interface does not work

  For those of you who, like myself, tried to install windows 8 in a Toshiba Portege M750 and had problems in tablet in portrait mode I recommend the following driver, it works perfectly:

  http://CDN.Wacom.com/U/drivers/TabletPC/ISD_DualTouch_710-8.zip

  The problem that I had was that shot didn't work with the metro interface and touch works also and in portrait, strangely, when you touch the secren with different directions woul two arrows appear.

  This driver solved my problem.

  Hope this can help...

  Thanks for the info.

• Win7 64 bit freezes & arrow function does not work, do not click to navigate anywhere

  Win7 64 bit PC crashes & arrow function does not work, do not click to navigate anywhere, exceptionally after being on ~ 2 + hrs. I can only turn off by pressing the power switch for about 5 seconds.

  Hello

  You did changes to the computer before the show?
  
  Method 1
  Step 1: I suggest to start the computer in safe mode and check if the problem persists.
  
  Start your computer in safe mode
  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2:  If the problem is solved in safe mode, then I suggest you perform the clean boot and remove the program that is causing the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: Follow step 7 clean boot KB929135 article to reset the computer in normal mode.

  Method 2
  I suggest you try the steps from the following link:

  Optimize Windows 7 for better performance
  http://Windows.Microsoft.com/is-is/Windows7/optimize-Windows-7-for-better-performance

  Also provide an observer event logs.
  Open event viewer
  http://Windows.Microsoft.com/en-in/Windows7/open-Event-Viewer

• My Atheros AR5007EG wireless network adapter will not work

  I have an Acer Aspire One AOA150ZG5 that only comes with Windows XP directly from the factory. I recently started having trouble with XP so I switched to Windows Vista Home Premium and now my wireless card doesn't work. I tried to go to the manufacturer's Web site, but they have only taken over XP, so I installed the XP driver and used the Vista Device Manager to update and it still does not work. Please help me I spent all my money on vista so I can't afford a new wireless card.

  If Acer is not taken support Vista for your model, there is nothing that can be done about it.

  Sorry about that.

  You can consult the Web site of the manufacturer of the wireless adapter.

  If they have no drivers Vista, same thing; nothing can be done about it.

  See you soon.

  Mick Murphy - Microsoft partner

• Drivers for NETGEAR WG311v3 54 Mbps Wireless PCI Adapter will not work.

  Windows 7 installs the drivers for the WG311v3 automatically, but after installation, the hardware does not work and I have an exclamation mark next to the card wireless in Device Manager.  I then looked at the properties and saw in the device state that "the device cannot start. (Code 10) "this device worked under vista, but doesn't work on 7. I installed the drivers that came with him and tried all compatibility modes, but nothing works. Any Suggestions?

  My hardware is
  -Intel Core 2 Quad CPU Q6600 @ 2.40 Ghz
  -4 GB DDR2 800
  -Geforce 9600 gt
  -motherboard: Asus PN5D

  Have a look here

  http://KB.NETGEAR.com/app/answers/detail/A_ID/11127/kW/Windows%207/r_id/100109

  above the link for the driver

  http://forum1.NETGEAR.com/showthread.php?t=41978

  I have not updated my, but did some research on the whole.

• scanner Kodak i40 64-bit of Windows 7 will not work

  Will not install drivers that work with windows 7 64 bit. Kodak has said that it should work, as possible. Said to contact Microsoft.

  Error messages?

  Driver for Kodak page does not list Windows 7 drivers:
  http://graphics.kodak.com/docimaging/us/en/products/Document_Scanners/desktop/i40_Scanner/support/Drivers_And_Downloads/i30_and_i40_Scanner_Driver/index.htm

  JS http://www.pagestart.com

• NETGEAR Wireless adapter WG111v3 will not work

  So I have this adapter wireless netgear WG111v3 and cannot connect to the Internet. I have windows 7. My office says that I don't have a wired adapter. Help

  Anthony,

  I you have to check out these items-

  http://Windows.Microsoft.com/en-in/Windows7/view-and-connect-to-available-wireless-networks

  http://Windows.Microsoft.com/en-in/Windows7/add-a-device-or-computer-to-a-network

  http://Windows.Microsoft.com/en-in/Windows7/cant-connect-to-a-network

  http://Windows.Microsoft.com/en-in/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Let us know if that helps.

• Portege M200 - utility, formatting SD and utility Boot will not work

  I can't get the SD format or the boot utilities to work. None of them see the SD card which is a new Panasonic 256 MB. I uninstalled the software and SD drivers and reinstalled them (in the right order, as far as I can tell) but nothing is.

  Anyone has any suggestions as to why it don't work?

  Hello

  you have activated the service of smart card in the 'Services' in your "Administrative Tools" window which is in your "Control Panel"?

  Please check if the smart card service is marked to start automatically and check if all the service is started.
  Would appreciate some comments.

  Welcome them

• Moved an old (16-bit) software to XP, will not work.

  We ran a spectrophotometer on a Windows 3.1 via a GPIB-CIIP/IIA card machine, but when the computer is dead we have found another one with the older card slot so we used ae try the GPIB-USB-B on a Windows XP computer. The Explorer of the GPIB Solutions can communicate with the instrument, but the software does not see the instrument. In the original file for the spectrophotometer software, it says to go to system.ini and add the device=c:\gpib-pcw\vdmad.386 line.

  Because we no longer have this file we watched the Windows\System32 folder and found several gpib*.dll files. We tried gpib.dll, gpib - vdd.dll and gpib - 32.dl, instead of VDMAD.386 (we fixed the path name too) so far, but none of them worked. We also don't run the updatdos.exe successfully but saw no effect. We have a Win 98 machine that has a USB port, but we need a driver to run it. Any suggestion would be appreciated.

  I had the famous camera. The instrument is now running on the XP machine, but still doesn't work is not on the Windows 98 computer. I'll keep trying because the software starts the 98 machine and then crashes so I think I'm close here too. To rename the device in Windows 98, I could follow the assistance OR the models tab of device file. Windows XP I had to seek help on the Configuration utility to find the device model dialog box.

• Can I do a clean install of Windows 7 Pro 64 bit on Vista Ultimate 32-bit upgrade. Installation file will not work. The error is described below.

  The XPS 730 with Intel Q9450 computer yourself running Windows 7 64 bit? The details of performance show that it is capable of 64-bit. When I try to install Windows 7 pro 64-bit upgrade, the installer will not work. I get an error that reads:
  The version of this file is not compatible with the version of Windows that you are running.
  
  I'm currently running Vista Ultimate 32 bit. Everything that I read on Microsoft and elsewhere says that you can go from Vista 32 bit to an operating system Windows 7 64-bit as long as you do the clean install. I'm that far away since I can't even run the installation.
  Maybe nobody knows what could be the problem?

  Hi Hal K,

  Thank you for visiting Microsoft Answers.

  If you are currently running a 32-bit version of Windows, you can only perform an upgrade to another 32-bit version of Windows. Similarly, if you run a 64-bit version of Windows, you can perform an upgrade to another 64-bit Windows version.

  If you want to move from a 32-bit version of Windows to a 64-bit version of Windows, and vice versa, you will need to back up your files and then perform a custom of the version of Windows you want to install installation.

  You can see the following link, installation and reinstallation of windows: http://windows.microsoft.com/en-us/windows7/Installing-and-reinstalling-Windows

  http://Windows.Microsoft.com/en-us/Windows7/32-bit-and-64-bit-Windows-frequently-asked-questions

  Swati K - Microsoft support technician
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Portege R700 - Windows 7 32-bit - NETWORK adapter driver does not work.

  Hi all

  I rebuilt a Portege R700 with Windows 7 32-bit o/s. I downloaded the drivers from the Toshiba site but could not get the only rider listed working card. It seems to install ok but will not work. If I try to 'put to date pilot' with Device Manager and point to the files expanded, he said that the required software is not found.

  Is there a driver that works and can someone tell me where it is please?

  Concerning

  Dave

  > No idea what driver NETWORK card works and also which driver, I need for the controller PCI of communication Simple?

  This seems to be the controller of Intel AMT.
  You can download the driver form Intel page.
  Search for Intel AMT or check this link to the page of the Toshiba driver:

  [Intel Management Engine Interface | http://eu.computers.toshiba-europe.com/innovation/download_driver_details.jsp?service=EU&selCategory = 2 & selFamily = 4 & selSeries = 151 & selProduct = 5379 & selSh ortMod = 1019 & language = 13 & selOS = 29 & selType = all & yearu pload = & monthupload = & dayupload = & useDate = null & mode = a llMachines & search = & action = search & macId = & country = al l & selectedLanguage = 13 & type = all & page = 2 & ID = 75561 & OSI D = 29 & driverLanguage = 42]

• Wireless communication switch does not work - Satellite A200 - 23 c

  The laptop has been included, and both a WI - Fi connection stopped working.
  Wireless communication switch does not work. Do not ask is it possible to do?

  Your English confuses me a bit little, but can you please tell me what model of laptop you have and what is the problem here?

  Wireless network card is enabled correctly in Device Manager?

• Wireless, Satellite A500-17 x will not work

  Hello

  Bit of an issue, the wireless on my laptop will not work. It is certainly a problem with the laptop itself, the router etc are all fine. I can connect to the internet with a cable, but Wireless does just not all. The switch on the front of the laptop, which should turn the radio power, has no effect. Before this problem of switching on the position 'on' would cause icon connection Wireless next to the switch to light up, it's no longer the case. Furthermore, when I tried to check the drivers in Device Manager there are only one option under "Network adapters", which is the "Realtek PCIe GBE Family Controller. Right click and select "update driver software...". ' result in a message saying that the proper drivers are installed. I don't know, but I suspect that there may be a lack of adapter or something?

  Any help much appreciated.

  Maybe some unknown device appears in Device Manager?

  You should have 2 entries for network adapters. One for the LAN and the other for the WLAN.

  By the way: when you set switch WLAN on WE and when you use FN + F8 what happens exactly?

• The Peer Name Resolution Protocol service (PNRPsvc) or peer network (p2pimsvc) Identity Manager service does not work

  I get the following error message when you run windows network diagnostics. I ran the diagnosis because I have a network with Win 7 Ultimate 64 bit on a computer and WinXP 32 bit on the other.  Curiously, I can easily see and manipulate all files through the firewall of Windows XP. Either way, Windows XP can not see files on Win7. I can drag files to the shared folder, XP can see them, but can not open the same when I enable the share using Win7.  I can see the Win7 computer name and I have a home network without password. When I click on the folder with XP, the error popup grey box says that I might not have permissions to access these files. Contact the administrator of systems etc. My network has the same name on both computers, so I feel totally betrayed by what is happening here. There should be no problem but there is a.

   

  I get this error message when you run windows network diagnostics:

   

  The Peer Name Resolution Protocol service (PNRPsvc) or peer network (p2pimsvc) Identity Manager service does not work, The Peer Networking Grouping (p2psvc) service depends on these two services to work correctly

   

  I've followed these tips nothing does not:

   

  ·                                                                                                                                                                                                                                                     To see which services are/are not running click on the ORB start and type Services in the search box at the bottom of

  the menu. Select Services results.

  Check the columns of type status and commissioning for "Start" and "Manual".

  Those who are not running, then select properties in the right click menu.
  Click the startup type box and select manual in the menu, then click on apply, then OK at the bottom of the window.
  Now try to Start the service for the option in the main window.
  Try the homegroup connection, if the service starts

  Try a reboot if all goes well. The settings may or may not stick!

  Scroll down the page until you see the following...
  Select Services results.

  Hi MarkWebber,

  Method 1: I suggest you to follow the link provided below to start your computer in safe mode with network.

  Advanced, including safe mode startup options

  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  If it works fine in safe mode with network, try to put your system at startup mode minimum state helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 2: Studied the problem and found the solution. A file has been corrupted and remove he got running PNRP service. The file has been re-created correctly when the PNRP service started upward. Here is the file for future reference:

  'C:\Windows\ServiceProfiles\LocalService\AppData\Roaming\PeerNetworking\idstore.sst'.

  Hope this information is useful.