HP charger compatibility

Similar Questions

• ProBook 6460 b: Charger Compatibility

  Hello

  I have a probook 6460 b that came with an HP 90W 18.5V power adapter. I also have a 120w 18.5V wich adapter (from my dv7 Pavilion 7050 hp previous-eb) that I use on with the probook. Can I use the charger 120w? or it does not damage the battery or something? (had to replace the battery and do not want to damage it).

  Thanks in advance

  Stijn

  Stijn_DeMeyer wrote:
  

  Hello

  I have a probook 6460 b that came with an HP 90W 18.5V power adapter. I also have a 120w 18.5V wich adapter (from my dv7 Pavilion 7050 hp previous-eb) that I use on with the probook. Can I use the charger 120w? or it does not damage the battery or something? (had to replace the battery and do not want to damage it).

  Thanks in advance

  Stijn

  More it will not damage but please make sure that the charger port is the same size and shape. Otherwise, you may cause arcs and damage the port.

• HHP Pavilion DV6-6177la: Charger Compatibility

  My old charger no longer works, was the number of 609941-001, PPP016L-E model substitution, output: 120 W, 18, 5V-6. 5a.

  I have an a new spirit a differenc part number: 384022-002, model PPP016, characteristics and connector and not work immediately.
  I want to know if there is a difference between them, and if it can cause me problems in the future.

  even power plug (volts, AMPS) and same connector = no problem

• BlackBerry Smartphones charger compatibility

  Can I use my old model charger for new 8330 8700?  Are they compatible?

  Altogether. Can of course. I do, even those of my 7100.

  All models 71xx, 81xx, 82xx, 83xx, 88xx 9000 use the same Mini-USB charger.

  The 95xx use Micro USB.

• The magnetic charger compatibility

  I was wondering if the magnetic compact xperia z1 (DK32) loading dock works with the xperia z2.

  The dimensions are exactly the same thing on the aceessory page.

  the dimensions of the hull may be the same, however there are inserts to accommodate different size phones - that you mention, I can confirm works with the Z1 and Z Ultra if you change the inserts because of different widths - I would check Xperia care for an answer official http://www.sonymobile.com/global-en/support/contact-us/

• USB charger - 29W C - compatibility with 12.9 "iPad Pro

  I'm looking for an answer as to if the USB - C 29W charger is compatible with the iPad to 12.9 "Pro. I know this question has been asked and answered by the communities in the past, but when I went to the Apple Store to buy the charger today, the staff told me that the charger could damage my battery over time. I then started a support chat session to confirm the answer and the representative said (and I quote) "If 2 people advised me not to do something, I would not even waste my time." We could care less if you want to damage your unit. »

  First of all, I never got a rude responses to Apple, so it was a surprise. Secondly, I really just trying to get an answer to the question. Can anyone (especially Apple) help out me? Thank you!

  If it is not in the specs of the iPad, you're crazy to use it. The Chargers are cheap, the iPad is not.

  Barry

• The compatibility of Applications programs when I want Bitdefender 2013 charger, ' jai windows seven 64-bit could you help me thanks Frank

  So I bought the latest version of Bitdefender total security 2013 when I want Bitdefender charger it me appears when the files are installed in a rectangle bdagent.exe 0xc000007b application, I can't used my antivirus, ' jai windows seven 64-bit could you help me thanks Frank

  Please select your language from the drop-down menu at the bottom of the page to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the desired language, support for additional international sites options are by following the link below:
  

  Good day

  Please get your language in the drop-down list above pour post your question in the language of your choice. The forum you posted is in English only. If you can't find the language of your choice above, options of fees to pay to other international destinations can be found by following the link below:

  Thank you
  
  http://answers.Microsoft.com/fr-FR/windowslive/Forum?tab=unanswered
  http://support.Microsoft.com/common/international.aspx

• Can I charge my iPod Shuffle 4th Gen with a wall charger or do I need to use a computer?

  Can I charge my iPod Shuffle 4th Gen with a wall charger or do I need to use a computer?

  You can use a wall charger. The following, for example, shows in the section compatibility as being compatible with the iPod Shuffle 4th generation: http://www.apple.com/shop/product/MD810LL/A/apple-5w-usb-power-adapter?fnode=0a8 96cef6682809aaf80e8c3741f09ed6d7df9585e7fc21bb39381e2a99a7f56b6f149e5ab72d8416a9 bfa670e36cc43168558b8b8c033b881948c1230b7156cbe51af44f7fd2b9ab533d7cb453e844ccd1 80b8e71aa7359ff2698b40de39b3b

  The foregoing generally comes with iPhones, but if you have a charger which comes with an iPad, which can also be used with the Shuffle: http://www.apple.com/shop/product/MD836LL/A/apple-12w-usb-power-adapter?fnode=0a 896cef6682809aaf80e8c3741f09ed6d7df9585e7fc21bb39381e2a99a7f56b6f149e5ab72d8416a 9bfa670e36cc43168558b8b8c033b881948c1230b7156cbe51af44f7fd2b9ab533d7cb453e844ccd 180b8e71aa7359ff2698b40de39b3b

• Watch USA/UK compatibility

  Hello

  a friend has offered to make me a Apple Watch when she goes to the United States as soon as she thinks they may be less expensive than buying one in England? So my first question is... are they cheaper to buy in the USA? Second, I don't know if there will be compatibility problems, use it in the United Kingdom.

  Any advice would be much appreciated.

  Thank you

  Hard to say, really.  Prices in the United States are generally tax-free and tax must be added at time of purchase and varies depending on the State.

  You must also consider shipping costs and import tax differences in the United States and the United Kingdom.

  Search shops online from Apple for the United States and the United Kingdom the watch you want and compare prices.

  Regarding compatibility, the watch is equivalent to one everywhere. You will need to get a form of adaptation for u.k taken wall then you can plug the charger well.

• Can I charge my iPod with my iPad charger or different voltage

  Can I charge my iPod Classic with my iPad charger or the voltage is different?

  The voltage is the same, so you can try it safely.  Apple says...

  Using the iPad with your iPhone, iPad, and iPod - Apple Support power adapters

  However, I have seen the reports here this iPod classic does not work with some of Apple's USB adapters.  For example, it is the adapter of 12 watts of power, which is the one that is provided with some iPad models

  http://www.Apple.com/shop/product/MD836LL/A/Apple-12W-USB-power-adapter

  While other iPods are listed under compatibility, iPod classic is not.  The smaller adapter 5 watts of power (which came with mini iPad)

  http://www.Apple.com/shop/product/MD810LL/A/Apple-5W-USB-power-adapter

  shows iPod classic models under compatibility.  Another power supply supplied with iPads works 10 watts; There is no separate current entry for it in the Apple Store.

• Question about the compatibility of battery

  I have the battery problem with my laptop. When it is installed in my laptop, it is not very compatible.
  Therefore, I have to buy a new charger http://www.batterystyle.com

  Bought new battery is good but I still want to learn more about this battery issue.
  Why it is not very compatible?

  Hello Darling

  To be honest I do not understand your problem at all. Can you please provide a little more information on your laptop?
  Please be so kind and explain the more detailed problem, especially what you mean under compatibility.

• USBOTG and Charge at the same time on Stream 8

  To keep this thread as productive as possible and efficient for those who find it useful to:

  Unless you have under your eyes

  1. a schematic representation of the 8 Stream USB port (USB port and battery electric circuit etc.)

  2 source code for the firmware BIOS and kernel that controls the material

  Please DO NOT respond or say "is not possible".  In view of the above is true, you do not have enough information to say '' not possible. ''

  If no one replys with a solution, what he calls not possible by default.

  Also please do not answer to say ' I don't know how "or" but I know how to do anything else that ' is also not that useful.

  An update of the BIOS or other software update may be required by HP, Microsoft or both to offer this feature really intuitive and quite possible.

  And I hope that this thread can be an effort consolidated by all who have the 8 flow to make the necessary changes.  The majority of the other tablet PCs are capable of it.  It seems that only the 8 Stream and a few others have trouble with her.

  ~~~~

  I want the ability to use a simple, inexpensive cable and perhaps standard (with electronic active minimum inside) which allows me to host and to use one or more USB devices on the Stream via its USB port B microphone 8 while this cable can also be connected to a charger standard and charge 8 flow simultaneously.  This means that the cable has a minimum of three connectors.  One of the possible configurations are as follows (apart from the normal charging cable):

  1 cable Micro USB B Male - connect to the stream 8

  2 USB male A - connect to the AC charger (IE one that came with the 8 Stream)

  3. USB A female - one or several connectors to plug into the key of USB data, keyboard, mouse or even a hub.

  Connector # 2. above shall provide a power supply to recharge the 8 Stream via conn. #1 and the power supply for external USB devices via conn. #3 so that they are in use - all at the same time.

  A and if the same cable can act as a normal OTG no charger for when no external power supply is available.  This may necessitate a switch or an electrontics active inside.

  The last part of this goal is unimportant for various reasons.  I wish that HP, the manufacturer of 8 flow, to State in writing good mode necessary to do this, so that other manufacturers or even-it yourself can make maximum use of their tablet HP equipment.

  ~~~~

  The neat thing it will alow a person to do with their tablet, it is to work at home using the Tablet as a desktop PC by connecting a keyboard, mouse, perhaps external screen (with USB to the display adapter) and knit for a long time without time limit prescribed by the battery life because the charger provides energy to all involved.

  If there is only a single connector on the cable #3, then an additional node of coarse had to provide support for these multiple USB devices at the same time.  However, it would be better if there were several #3 connectors integrated in the cable itself.  This would be better as a suitable USB hub also requires its own power.  That an adapter is necessary if the whole thing were integrated into one.

  ~~~~

  I really want answers from anyone who has already accomplished USB OTG delivered with simultaneous load with flow 8. (independent of any published 'proper' way is also welcome)

  Today's date is 2015-01-16.  If in 2015-02-16 (one month), nobody has posted a solution and then starts to bug HP and Microsoft on it's us?

  ~~~~

  Technical training:

  I understand the possibility the tablet software and firmware must take a decision on the manner in which power flows on the power port USB microphone B pins.

  I know that with a proper design of the electronic circuit carring these signals of power inside the Tablet could be sensitive to what is connected and without risk to decide for himself what to do without needing to control software.  For example by testing/detecting periodically differential voltage or current management to see what sides of the connector can supply.

  But this is only one of the many "could bes".

  In addition, this can be no standard regarding the standard USB.  What seems to be actually the case with a lot of cables OTG + fresh, is that physical clues embedded in the cable or charger are used to signal to the Tablet what the situation is.  Then the signal of software/firmware of the Tablet, interprets what the situation is intelligently and responds by flipping the bits of correct hardware control to activate, or deactivate the power flow in the port and also control its direction in or out.

  I'm not familiar with the standard USB.  Maybe I could do more research, if I believed that HP followed with 8 Stream or even the standard covered this situation explicitly.

  But to a certain extent, it seems I'll have to invent something that should be intuitively just like it does with other tablets. Isn't it?  Maybe I'm overthinking, but I can't find any USB OTG + cables load that specify compatibility with 8 HP flow.

  In any case, I was familiar with both methods other use of tablets to send the highest mentioned signal to the hardware/firmware/software of the tablet to the idea that it's time to load / time of OTG or both.

  The first method is a 0 Ohm to 200 ohms short between pin USB A 2 and 3.  This is the bidirectional data differential lines D - and D + respectively.  In data mode, all the data passes back and forth on those lines.  When you load with a cable, it's the charger module that puts this short, not on the cable.  I measured the short on three different Chargers.  It is 0 Ohms on two of them, one of those who are the charger that came with the 8 HP flow.  The others 0 ohms was generic.  The third was for an apple iPad and it measured on 53KOhms.  It's probably not the resistance ohms 0-200, but probably it is impedance termination indicating that there is some intelligent serial port communication in the charger itself.  Leave it to Apple to be different.

  This method is somewhat questionable, as this signaling mode would prevent OTG + fee because it seems unlikely that you will be able to OTG when the data lines are shorted each and overloaded with such low impedance.  I could be wrong on this subject...

  The other method I have seen suggested to work with some tablets and phones other than the 8 stream is too short the USB microphone B pin 5 to Terminal 4 with 0 Ohms to 100 000 Ohms.

  USB B has 5 pins.  USB has only 4.  The extra pin on B moves the GND pin 4 pin 5 pin to and makes pin 4 PIN ID.

  If this signal applies to a drop in the ID pin (4) or in some cases, I saw that she proposed, he runs down with 0 Ohms.

  Dead shorting things always makes me nervous.  If ID is a simple normally high impedance high input, resistance could be used to make voltage well below the low or zero threshold while also preventing the risk of damage when cheat on him with a device that you do not have the diagram for.

  Yet, 100K is a bit high for a 'pull down' in most of the situations that I'm used to.  Even a 10K would be uncertain. A 1 K or 2 K seems reliable enough, but then things are weaker and in know more nowadays low...   All but a dead short but if possible.

  So, it seems possible that the device might be able to "indicate" by the specific value of the resistance, which can be found here.  In other words the resistance is not a pull down but in fact a signature analog ID, in which case the exact value will be crucial. So if this is the case, a guess is not going to work.

  Obviously in such a system as described above, a chip inside the Stream 8 should be responsible to support this information. I hope the 8 Stream has such a chip.

  Probably a register inside this chip would be at all times what the State of the pin ID is a binary number.  All that is needed is for the BIOS to the chip and the registry in it and read this number via the bus to determine what happens to the port. Finally, he would use that signals of info to send the order of material to the electrontics of power set the appropriate direction to take etc.  (and change the State of the icon on the screen of the rude)

  I don't know if the PIN ID method described is a standard USB or not either.

  Eventually, there may be a third way. But I do not suspect that it would be possible with a non-active external device. In any case too complicated for the novice DIY for sure.

  The device would need to act is a kind of extension of bus.  As an active hub.  But she would use the negotiation of data USB serial lines and in addition to reproduce one or more additional USB ports, intelligently inform the tablet to get with the program which is "now we're going to otg and recharge at the same time."

  This requires a smart external device with a processor Inside, no doubt.

  It seems to me that many other tablets have been able achieve avecjoint here the need for a smart external device and thus the flow must also be able to do.

  There is a device that claims to be able to work with the HP Jet 7 and 8 and provides same ethernet and USB and big DVI ports so loads the data stream.  But its expensive because it is active.  Se here:

  http://AMZN.com/B00OVDE0GC

  It's called a "Docking Station".

  A reference to a product that does exactly what I want (possibly without active electronic components) is here:

  http://AMZN.com/B00LTHBCNM

  It's by Kirin and it is a device of type squid with four USB ports.  Precisely, which is my goal.  But read in the comments stream 7 user indicated that he would not be OTG and load, not really clear if it worked as a hub USB OTG or not.  Another evaluator stated that she would not support even a single USB device much less fees of 8 Stream.  This device has a switch.

  I forgot to mention that some 'hackers' have claimed success with other tablets to deceive their devices by using a multi-step process to plug things in.  Usually in general they would get connected Tablet and load first, then they would return a switch or something remove some resistance or the signal was introduced by the first position of the switch. For some reason any Tablet would continue to require. Then the data lines would be free and they would plug in a usb key and it mounts correctly even if the tablet was always in charge.

  It's like the power circuit has a lock which does not allow it to return to the mode "power flow" as long as he still feels the power flows inward regardless of what software it is telling.  Full proposal here.

  These tips seem dubious to me.  Changes in the BIOS could change the way it works.  Also you can not be sure what actually happens if you do not have a schematic representation.  You could damage your tablet.  Many people will support icon in the operating system whether the Tablet is in charge.  But I'm sort of a low-risk guy and my policy is generally indicators of intereperet not to have meaning at all once a device is functioning in a non-standard setting.  Especially when it's something that I did not built and could not fix if I FRY.

  Hypothetical reasoning: tell me what data sensory discs really the State of the charging light screen?  This reflect the bit of hardware control programs actually feeding management and status on the port?  Or does it measure the direction of the flow of power, said in the section of the circuit battery monitoring?  Point - none of us have a schema because it's owner. To really be sure according to the smart electronic hardware, the port must be mode flow under advisement "of power. If it's in a "power flow out" mode and power will be delivered externally as well you wind upward with both power supplies the same power at the wheel nets.  In this case, the two opposing regulators attempting both to drive 5 V can have slightly different voltage calibrations.  That could lead to fighting between them, with more than 100% of their capacity.  For example if you try to regulate 4.95 real V and the other and other attempts to regulate 5.05 V.  Current then flows to the tune of 100 mV / a few milliohms in the cables linking the two.  This may be several amperes. (many)  In other words, like I said: you want the tablet to know that power is coming in don't go out and automatically hitting the internal switches needed for that to happen. Probably the icon should indicate this with precision, but in some wacky situation, he could not. There may be a chance that the icon could indicate the load and still be burning or focusing on some circuits of the tablet or the charger.

  Another thing, I could see that happening is if you play with these reported resistance types enough you might find a resistance value that winds up place the device in an intermittent condition.  In other words it keeps flipping back and forth quickly between OTG and fresh.  It can give the illusion that it works.  You can have marginal communication with your USB devices and battery could even load.  But will still be a lot of stress on the power circuit.

  It is difficult for me to risk a Tablet perfectly well if I don't know exactly what I'm doing.

  If a brave individual makes their own experimentation and verifies that it charges and OTGs and you tell the rest of us, you're a hero.

  Maybe one of you has a good knowledge on the USB standard to have more confidence in such an experience... like what the ID pin 4 REALLY supposed to work for example?

  That's what I know so far.  If you think you can help, thanks in advance, or if this helped you, then your quite welcome.

  It works

  http://Accessories.us.Dell.com/SNA/ProductDetail.aspx?c=us & l = to & CS = 19 & SKU = 470-abes & baynote_bnrank = 0 & baynote_irrank = 0 & ~ CK = baynoteSearch & dgc = CJ & cid = 47997 & lid = 4279734 & acd = 10550055-4485850-eb75dcb47e53437680ed323a1f4885fe

  Evidence

  http://targusblog.com/2014/11/25/how-to-turn-a-99-Tablet-into-a-workstation/

  But it's 4 x the price in Europe

  Have fun

• Satellite C660 - compatibility between motherboard and hard drive internal

  Hi, I have a problem with the compatibility between the internal (1 terabyte) hard drive and installing windows 7 pro.
  I broke my old internal hard drive (320 GB) and I bought the new hd (1 tb), but during the installation it says that w7 cannot be installed on this new hard drive.

  Can my pc motherboard (serial number: 3B071014k) support the new hard drive (serial number: wd10jpvx)?
  and if the answer is 'yes', how can I make it work?

  First of all the question has nothing to do with the motherboard and HARD drive compatibility.
  If the HARD drive is visible in the BIOS (first page), the HARD drive is supported by the BIOS and HARD disk controller.
  In the case where the drive HARD isn't recognized, you will need to replace this HARD drive with another. I guess the smaller size of the 2.5 SATA HDD THAT would be taken in charge (500 GB)

  However, in case the HARD disk is visible in the BIOS, you should be able to install Windows 7.
  Before starting the installation, you must format the HARD drive and should create the system partition.
  For this procedure, I recommend to use some tools such as partitions for example: GParted
  GParted is a freeware Linux tool.
  You can create a bootable USB key in order to start the device using GParted:
  http://gparted.sourceforge.NET/LiveCD.php

  Then, you should be able to format the HARD disk and create partitions.

• Charge dynadock U10 USB mode not working / charging

  Hi, when to detach before USB ports using the 2 do not charge an iPhone 4G. Its a Dynadock U10 PA3575E-1PRP. Set after undocking charge mode is checked in Dynadock Utility. iPhone charges ok when it is docked. As soon as the Dynadock is not docked iPhone stops to load.

  Any ideas?

  Only the remaining entries are here [http://forums.toshiba.com/t5/General-Technology/Cannot-charge-with-frontside-USB-Ports-on-Dyndock-U-with/td-p/143880] but no solution posted.

  Cheers, Dan.

  Other USB devices charge ok?

  It's may be an iPhone compatibility issue.

• Halo 2 for Windows Vista compatibility problems?

  I have problems of execution of Halo 2 for Vista after installing it on my Windows 7 installation.  Whenever I start it, it immediately goes to "No answer" as soon as it loads.  I tried to start with the compatibility options for all versions of Vista (plain, sp1, and sp2) but nothing works.  It seems to freeze at the part where it loads in the Games for Windows Live components.  I saw elsewhere that people have problems with this and that by removing completely all Games for Windows games and executives charge then reinstall them with Halo 2 first worked.  This has not worked for me, and after some further experimentation, I decided to check if it was a hardware problem, so I did a clean install of Vista and had no problem if he started.  All my drivers are up to date, but I can't find any more away.  Any suggestions?

  My computer is an Intel Core i7 920 on an Asus P6T with 6 GB of RAM running Windows 7 Ultimate x 64 with Nvidia GTX260 graphics.

  Developer, student, professional computer

  Yes of course a lot of people have problems.

  Here a few other sites:

  http://forums.gamesforwindows.com/p/8000/74420.aspx#74420

  http://forums.gamesforwindows.com/t/8958.aspx

  http://www.modacity.NET/forums/showthread.php?22030-Windows-7-walkarounds-%28Halo-2-for-Windows-Vista%29

  You can also try a clean boot .