HP Deskjet 3522 - cannot close the cartridge access door

Similar Questions

• J5780 "open door. Close print cartridge access door. »

  I just installed a new HP 74 cartridge in my J5780 AIR. Orange flashes and the message 'close the door. Close print cartridge access door"keep scrolling in the message window. I can't find such door. When I close the half top of the machine, the amber light continues to blink and the error message continues to scroll. Help, please!

  This document open door message can help:

  http://support.HP.com/us-en/document/c01050739

• OfficeJet pro 6830: transport cannot return the cartridge access area

  I'm trying to set up my new printer 6830, but I got the transport Jam error message: "remove any packaging from inside the printer.» After all packaging is removed, turn the printer off and then turn it back on. "My new printer came not with the thing of white foam in the transport. And I think I've removed all the bands and plastic/foam of the printer as shown in the introduction the guide book. Could someone tell me where should I look for a package that needs to be deleted? Really appreciate any help.

  Hi Meiaja,

  Here is the link to HP customer care:

  https://support.HP.com/us-en/contact-HP/product/HP-OfficeJet-Pro-6830-e-all-in-one-printer-series/5390307/model/5390308

  Scroll down the page and you will find a support model to fill.  Once you fill out and click on 'Show the Options', you should get an option to call the help desk with a no of cases.

  I don't know the policies of Tiger Direct.  They can cover the cost of shipping, or they may not.

  I would call 1 HP customer care.

  Jean

• Error message = close print cartridge access door

  I've set up my new 4500 series printer and I can't get rid of this error message.  I tried all the steps listed on the HP support site, but no help.  I can't print at all.

  There is a document with the steps to solve a door open error. This document can be found here. You say that you did all the steps on the HP support site, but make sure that no steps have been omitted in the document.

  If the error persists, then try to perform a hard reset.

  Hard Reset:
  Unplug the unit when turned on
  Disconnect the other end of the power cord from the wall jack directly
  * Wait 30 seconds
  * Connect the device upwards.

  If the error persists, then try a partial reset. This reset path can be found in the document located here. The 4500 is not listed, but the reset is the same as the Group of the top in the document (method 3 and #).

  If this error continues to display after all these steps, then I recommend to contact HP Technical Support on this printer. If you are still in warranty, HP can replace the printer without cost to you. I'll link the information to get in touch with them below. The link takes you to a form to fill out. Once you fill it and she is treated, it will give you the printers warranty information, a file number and the phone number to call.

  HP Technical Support call case form:
  https://h10025.www1.HP.com/ewfrf/wc/phoneInput?cc=us&DLC=en&LC=en&product=5061082

• Cannot close the first with other (LH one end) tab open are closed.

  Cannot close the first tab (end of LH we) but others are closing. Indicator download on tab keeps indefinitely - running windows under all the tabs are functioning normally.
  Open another copy of Firefox allows all tabs to work normally in this copy

  If this does not work in mode without failure, then disable all extensions and then try to find out who is the cause by allowing both the problem reappears.

  • Choose "Disable all add-ons" on issues to troubleshoot Firefox in Safe Mode to set window to disable all extensions.
  • Close and restart Firefox after each change through "file > exit ' (Mac: ' Firefox > leave";) Linux: "file > exit ')

  See Troubleshooting extensions and themes and problems of hardware acceleration to resolve common Firefox problems

• I have a statioery box that appears in the cenbter of my screen. Cannot close - the cursor moves UNDER it. How can I get rid of him?

  I have a box of stationery that opens in the center of my screen.  Cannot close - the cursor moves UNDER it. How can I get rid of him?

  Hello

  1. when exactly you get the pop up?

  2. What is the pop up to say?

  Additional information on the issue so that we can better help you.

• Reinstall the cartridge on the printer access door.

  My Office Jet J6480 CB053A cartridge access door is out of the hinges.  I need instructions on how to reinstall the door.  Any help would be appreciated of course.

  Hey there haz9L,

  If access it carries has been completely removed and detached from printing the part would need to be replaced. I suggest you to contact HP for a replacement, especially if the hinges are broken.

  You can find the contact here Pnrtie:
  http://WWW8.HP.com/us/en/contact-HP/phone-assist.html

• PC W7 cannot close the creative Cloud application

  Does anyone know why my pc W7 cannot close the creative cloud application when I stopped my pc?

  When I want to shut down the pc, I always have a message and must close the creative application Cloud by force (I don't know the passage of law).

  THX!

  This seems like a minor issue, so I recommend leaving her alone and allowing victory to force her to stop.

  You can also open your Preferences cc dialog box and not start cc when you connect if this prompt mind.  Just run the application cc, at most once a month.

  and if you want to solve the problem, you would probably need to uninstall any cc including the application office, specific to the use of the Adobe Creative Cloud cleaning tool to solve installation problems , restart your computer and reinstall the desktop by https://creative.adobe.com/products/creative-cloud application

• Problem installing G510n - "open cartridge access door.

  I want to install a printer/copier/fax g510n - just installed the ink cartridges and still receive the error message 'cartridge access door open - closed door acess cartridge' even if I closed the door.  I can't continue the installation. Suggestions?

  Hello

  Thanks for the post.  With this one, I might suggest the following two links below.  The first is a t - shooting document that covers the common things to look for with this error message.  Good luck!

  http://support.HP.com/us-en/document/c01952299

  http://support.HP.com/us-en/document/c00829896

• HP C7280: ink cartridge access door is open

  Hello

  My HP Potosmart C7280 AIO (all-in-one) is stuck with an error message.

  Door open

  Ink cartridge access door is open.

  I have reeived a printer replacement in support of July 2008 and HP will not help because my original printer was purchased in Dec 2007.

  Google did not help

  Search HP support site did not help

  User manual did not help.

  I also tried this:

  power off

  Unplug the power cable

  Wait a minute

  Press and hold the "#" and "6" keys

  Plug in power chords

  Be patient

  Wait for the white screen out.

  Release the keys #6

  Press the button power

  ... all of this in the hope that a false alert will disappear. There NO :-(

  Experts out there?

  Is - this firmware/hardware translation?

  In the future, I'm not spending a dime more with HP unless this issue is resolved in a satisfactory manner.

  Help to get forward.

  Pete

  Message edited by prnthlp on 05/21/2009 12:27

  I also sent the email below to HP support and hoping that someone will help.

  Sent by e-mail E-mail form
  Please contact the e-mail HP support

  Thank you for sending your e-mail to the customer of Hewlett-Packard. You will receive a system generated acknowledgement [[the lapse of time, may vary by region]]. If you do not, please resubmit take extra precautions to make sure that you enter a valid and functional e-mail address.

  If you have additional information or request for information, please contact HP

  
  When did you purchase your product? : 2008

  Product HP Photosmart C7280 all-in-One Printer

  Select a problem area: error messages

  What is your serial number (SN): MY82NH43NC

  What is your operating system? : Microsoft Windows Vista Home Premium 64

  How your product is connected to your PC? USB cable
  
  If there is an error message, please specify:

  Door opening / Inc. cartridge access door is open

  Description of the problem: the ink cartridge access door is not open, but this post just won't go away! The printer is in normal state (not open) and I am ready to print. How can I get rid off the coast of this message. Help, please.

  Please provide previous steps of troubleshooting, or information that can help HP help you. :

  I tried to plug the printer in holding together the "#" and "6". In the past it has helped to solve other problems of the firmware, but this time the message "access cartridge door is open" message remains on.

  Nothing changed since the device was working properly (installation of SW, settings, wiring, etc.): Nop.

  How would you describe your level of technical skill? : Advanced

• DeskJet 5550 cannot print the page to clean cartridges.

  DeskJet 5550, Win 7 64 bit, after clicking on the clean print cartridges, it does nothing. Power light is solid on. The menu box arrives with Click clean to clean the cartridges now. Clicking on clean makes this area of empty menu and nothing happens. No error or no program has stopped responding. Can the text and images fine print except that I need to run the utility for a few minor flaws. Past to the best setting which helped a lot. Does not print the calibration page either. Prints all the tests and the test page.

  I believe you can force a cycle of cleaning as follows: power on press and hold the power button, press on and release the button X twice quickly, then release the power button.  No page will print, but you should hear the printer to clean.  A more aggressive cleaning can be done by pressing the X button twice and once the page break button, a still more energetic cleaning by pressing the X button twice, then press the page twice break before releasing the power button.

  You can print a diagnostic page holding the power and then button by pressing the X button eight times followed by the button to jump to page four times, then release the power button.

• DeskJet 460, cannot use the Toolbox Windows in Windows 7

  Just bought mobile printer HP Deskjet 460 take traveling with the new laptop, which will no doubt be Windows 8.  Installed printer on my computer running Windows 7.  Installed automatically when I plugged it in.  Do not have installation CD.  Downloaded Windows box to tools on the HP site, but when I try to use it I get message cannot use it because the printer driver is not installed.  Tried the solution I found in this forum to run the Toolbox in compatibility mode for Vista and that caused a window to open it by saying I need to align the cartridges, but the Toolbox then basically hangs and will not function.  How can I perform the functions described in the user guide when they say open the Toolbox?

  The printer prints large so far, but I have a feeling I'll need Toolbox afterwards.

  Is this printer just not completely compatible with Windows 7 or 8?

  Is there another way outside the Toolbox to align the cartridges or clean them or what is in the box at tools?

  Hi @KathyAtHome

  There is no complete software driver for the 460 Deskjet which is compatible with Windows 7 or 8, instead, you use a driver in OS and features.

  With the - OS driver, some of the buttons on the product do not work, and some of the advanced features of these products are not available. For more information about your driver in the OS and see workarounds for lost features, go to the frequently asked questions section.

  You can see, " ", "workaround solutions use following HP Toolbox when you install the product using the driver in Windows 7. "

  

  BUT,

  You can use the print HP and doctor Scan to perform this maintenance like cleaning the print heads and to check ink levels.

  

  

  

  Click here to download and run the print and Scan Doctor > www.hp.com/go/tools

  If you need help, let me know if this resolves the issue, please let me know by marking this message as "accept as a Solution. Thank you.

• The title bar has stopped working and now I can't close the page with the cross or minimize or maximize, cannot close the pages

  Toolbar is not functional cannot use the cross at the top to close and cannot minimize or maximize the pages.

  What program is this (name and version)?

  Are you sure that the title bar is not hidden because the screen is in full screen mode?  Make sure it is in normal mode (usually hit the ESC key will do that).  When you say that you "cannot minimize or maximize or close pages" is because you don't see these icons or press them, and they do not work?  You see the title bar?  Is it the same with EACH program or all instances of this particular program, or only with this page?

  If it's an open program, you can still use the toolbar at the bottom of the screen and do a right click on the prgram open and then click Close.  If it isn't there, it can also be hidden. Move your mouse to the bottom of the screen and see if the toolbar appears.  If so right click on it and select properties and uncheck Hide able toolbar and click OK to close - that way it will always show (except when it is in full screen mode).

  You can also press CTRL-ALT = DEL to bring up the Manager tasks, go to Applications and select the program that you want to close, and then click end task.

  If you have access to the Menu bar, you can usually go into file, and then click close tab or simply close.

  If you can help me with answers to my questions (assuming that what I said has not solved the problem), then I will answer you with some suggestions to solve the problem (whatever it is)-, but there are too many possibilities without knowing more about the problem.

  Thanks and good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• J6840 cartridge access door does not close

  I just replaced my ink cartridges.  At the back of the access door are two sets of black bumps up and down. Tabs in one WILL NOT line up with the slots on the other.  I can open the door of ac cess to the rear, limited by the Ribbon control.  The printer will not do anything unless I can close that door and the back is always open about 3/4 ".  How can I get these tabs to line up so I can close the door?

  I tried to call technical support. Their solution was for me to buy a new printer.

• LaserJet pro 1415: cannot open the cartridge door and prints have red lines on them

  First problem was the red lines on the printed pages, now I can't open the cartridge door

  Just to close the loop, we decided to force the drawer open, because the printer was unusable anyway even if we have something broken. With a lot of pressure, the drawer open. We then tried to print something and a message there is a paper jam.  We opened the back door to clear paper jam and off broke a spring and a broken then only plastic parts. We cleared the jam and thought that the broken part just came to the door but was clearing of the works.  Then we printed out a page and everything worked fine.  If the door does not close completely because it is missing a piece, so what? The printer works fine. Thanks for trying to help.