HP dv5 1015ea - after change of hard disk, the notebook freezes

Similar Questions

• After change of hard disk

  When I change my hard drive of my laptop. computer watch

  

  What, in other words somethings else was unemployed? What can I do?

  My laptop is Dell inspiron 15 7537, and I change the same hard driver band for my laptop

  Hi James101ku,

  You must install Windows on your new hard drive. Please refer to my link below for a good installation guide for Windows.

  Good luck!

• 0xC8000247 error, cannot install Windows Update after change of hard disk.

  Error code original title: 0xC8000247

  I just replaced the hard drive in two laptops.  Set to launch on the third.  After replacing the hard drive by using EZ gig cloning software iv install the new drive hitachi that I tried to run windows update and received this error message.

  Hello

  Method 1:

  I suggest you to perform a System File Checker scan.

  Click on the link mentioned below for more information about the System File Checker analysis

  http://support.Microsoft.com/kb/929833

  Note: you may be prompted to insert the Windows Vista installation DVD, if all files are proven to be absent or corrupt.

  Try to install the update once the scan is complete.

  Method 2:

  I also suggest you to follow the steps mentioned in the link and check.

  Follow the steps listed in the article mentioned and check.

  Important:

  How to back up and restore the registry in Windows Vista

  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Cannot install updates in Windows Vista, Windows 7, Windows Server 2008 and Windows Server 2008 R2

  http://support.Microsoft.com/kb/2509997

  If the steps do not contribute not to proceed to method 3:

  Method 3:

  How to perform an upgrade on the spot on Windows Vista, Windows 7, Windows Server 2008 & Windows Server 2008 R2

  http://support.Microsoft.com/kb/2255099

  Note: After the upgrade on site, your personal data and installed programs will not be deleted, but you may need to run Windows Update to install all the updates that are available for your system to update these files system to the current version.

  If your installation DVD disc is prior to Sp1, and you have the SP1 is installed on your computer, you will need to uninstall SP1 to finish the upgrade on the spot and then reinstall the necessary windows updates. This applies if you have SP2 also.

  Try to install the updates once the installation is complete.

  Hope this helps and keep us posted.

• Can not reinstall the software after change of hard disk

  My old hard drive failed on me last week, so I had to buy a new one. I want to reinstall my suite adobe CS5.5, but the computer just spits the disc after a few minuets. What I am doing wrong?

  I have a mac book pro, mid-2009, with Snow leopard OS x 10.6.8

  You can work around the disc and download the free trial from the page linked below.  Then use your serial number to activate the software to use fully.

  Don't forget to follow the steps described in the Note: very important article Instructions on the pages to download to this site or the download may not work properly.

  CS5.5: http://prodesigntools.com/adobe-cs5-5-direct-download-links.html

  If it works, then there may be a problem with the configuration of your hard drive.

• Change of hard disk: System update will work?

  I consider changing my 7200 RPM HD with a new Intel Solid - State Drive 520 series 180 GB. How this will affect the use of the system to update? He will be able to detect and work with my new hardware, or it will stop working?

  Currently I left 725 days my Lenovo warranty. Change of hard disk would probably void the warranty.

  PC: ThinkPad X 1 (1294-2PG)
  5-2520M (2.50GHz), 4 GB RAM, 320 GB HD 7200 RPM, LCD 13.3 in 1366 x 768, Intel 802.11agn wireless, WWAN, Bluetooth, Intel HD graphics card, 1 Gb Ethernet, Ultranav, Secure Chip

  Hello.

  (1) you should have no problem with the update of the system after the upgrade of your player.

  (2) change the Player won't empty your warranty as long as you don't cause damage by improper installation.

  the player is called a "self-service CRU" (CRUS by). If you look at the hardware maintenance manual pg98 (http://support.lenovo.com/en_US/downloads/detail.page?DocID=UM006394), you will see that the disk is not #5 in the exploded view. a page to the bottom, you will see a single * in the RAW Id column for the items in the list #5. Scroll to pg97 and you will see the definition of a "CRU" self-service ".

  HTH a little.

• Portege S100 - upgrade after cloning BSOD & HARD disk

  Hi all

  I wonder if anyone can help me please. I have a laptop Portege S100 with a standard 80 GB drive. I want to upgrade to a 200 GB drive.
  Here's what I did.

  I ran Acronis to save an image of the 80 GB HARD drive. All backed by an external USB disk and checked. I inverted the readers and restored the image on the 200 GB drive. All restored and verified.

  I restart the PC with the new hard drive in place. "Windows XP" logo comes up, then aarrgh blue screen. Stop x7B.
  Swapped the old disk, system boots fine.
  Check in the BIOS, with the old hard drive in place that the RAID configuration is enabled by default

  New swap disk, JBOD configuration is enabled in the BIOS. Could this be why it is not booting? If I want to activate the RAID configuration, it is ok, but I'm told that it will wipe the hard drive!

  I have no qualms about wiping the new hard drive, but it will work? If I change the RAID configuration, then restore the image? The only reason why I have not done it so far is because it took some time to create the image, and then writing it back on the new disk and at that time there the owner of the laptop is needed it back. !

  Help appreciated!
  Thank you very much
  Alex

  Hello!

  Can you post the BSOD detailed please?

  I'm a little confused on RAID m parameters are you wrote. As I know the Portege S100 can handle only a single HARD disk.
  In addition, you must use the same settings as with the old HDD RAID.

  Maybe the SATA controller has a limitation of LBA 28 bit and can't handle a 200 GB HARD drive. In this case, the larger HARD drive should have 120 GB. Here you can learn more about the limitation:
  http://www.48bitlba.com

  Last but not least, you can see the new HARD drive for errors. Maybe it s faulty. For this, you can use the Drive Fitness Test:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT

  Sorry, but for the moment I put t have more ideas.

  Good bye

• Restores possible OneKey Rescue button on change of hard disk physical?

  I am a very new user of lenovo and recently bought an Ideapad Y460.

  The default hard drive is 500 GB with a speed of 5400 RPM.

  I wanted to change my hard drive to an SSD hard to increase performance.

  Before doing so, I created a set of recovery plant (3 DVDs) discs using the pre-installed OneKey Rescue System.

  I am aware that for the button OneKey Rescue work, the system must have a separate with the original disk image partition.

  My question is that if I install a new hard drive, the recovery of the DVD discs recover the original function of my laptop, returns to its new factory-installed state?

  The OneKey recovery will work properly?

  The recovery disks sutomatically will make the hidden partition, the C and the disks on my new SSD?

  Thanks for your time and any help will be greatly appreciated.

  replacing hard drive with rpm higher can help you.

  (consider about upgrading ram, too)

  http://Forum.Lenovo.com/T5/IdeaPad-Y-U-B-V-and-Z-series/disk-partioning-and-OneKey-recovery-feature/...

  (please, hit that "accept as solution" response if any message helped you to solve)

• I change my hard disk 500 GB, he had a particion front and right is now read 300gh, how do I retrieve the disc?

  I tried to format it, but the phone told me I don't have enough authority.

  Hello

  ·         What is the brand and model of hard drive?

  ·         Internal or external HDD that you use?

  Method 1:

  You can try to fix this by checking a disk or disks to find errors.

  I suggest to follow the steps outlined in the article below and check if it helps to solve the problem:

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Method 2:

  I recommend you change the drive letter for the drive and check if it solves the problem.

  a. Click Start on the taskbar, and then right click on my computer on the desktop or in the start menu then click on manage.

  b. under computer management, click Disk Management.

  c. in the list of drives in the right pane, right click on the removable device and then click on change drive letter and paths.

  d. click on edit and in the drop-down list box, specify a drive letter for the removable device, choosing one that is not assigned to the mapped network drives.

  e. click OK, and then click OK again. To assign a drive letter if it has not already received, click Add, click the letter you want to use, and then click OK.

  Method 3:

  You can also check out the article below and check if it helps:

  Formatting disks and drives

  http://Windows.Microsoft.com/en-us/Windows-Vista/formatting-disks-and-drives

  Note: Formatting erases all existing files on a hard drive. If you format a hard drive with files it contains, the files will be deleted. Make sure that you back up all your important data.

  Thank you and best regards,

• Qosmio F50-125: change of hard disk

  Hello.

  I would like to replace built-in HDD: 400 GB, 5400 rpm
  with other 3.5 "HARD drive: 320 GB, 7200 RPM

  The end user is able to do?
  In is it guaranteed?
  Can I use the rescue CD, which I created with the Toshiba utility (with current HARD disk) to preload the new drive with operating system and Toshiba Utilities?

  Thank you.

  Hello

  You cannot use the 3.5 HARD drive
  Qosmio F50 supports SATA 2.5 HARD disk

  Usually it s HARD drive no matter what speed it is.
  Important are the specifications mentioned above; 2.5 and SATA interface.

  With regard to the guarantee.
  Usually the upgrade of RAM and HARD drive should not avoid the warranty

  See you soon

• Cannot open acrobat 9 pro after upgrade mac and change of hard disk

  I worked with the Adobe Creative Suite and Adobe Acrobat Prop 9 years without any problem. Recently, I had to put my mac OS to El Capitan and replace the hard drive. Even though I reinstalled all data and programs of a time machine back up the new disk, since this happened my pro reader adobe acrobat does not open. It freezes. I don't know it is a compatibility issue with El Capitan or a problem created from the new hard drive, but I would appreciate anyone help and advice on how to solve this problem.

  Thank you.

  There is not acrobat reader pro.  There is acrobat pro (costs money and you have a serial number) and adobe reader (free and no series number).

  assuming that you have acrobat pro, uninstall everything which is currently installed by using the adobe uninstaller program.

  then install properly using your serial number and the installation file.  also, you need allow unidentified publishers:

  http://Mac-how-to.WonderHowTo.com/how-to/open-third-party-apps-from-unidentified-Developer s-mac-os-x-0158095.

  Available downloadable Setup files:

  • Suites and programs: CC 2015 | CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4, CS4 Web Standard | CS3
  • Acrobat: DC, XI, X | Suite X | 9,8 | 9 pro extended exe,7z extended pro 9 | 9 standard | 8 standard
  • Captivate: 9 | 8 | 7 | 6 | 5.5, 5 | 1
  • Cold Fusion: 11: 10 | 9.0.2 version 9.0.0, 9.0.1, 8.0.1, 8.0.0, 7.0, 6.1, 6.0, 5.0, 4.0
  • Contribute: CS5 | CS4, CS3 | 3,2
  • FrameMaker: 12, 11, 10, 9, 8, 7.2
  • Lightroom: 6,7. 5.7.1|  4.4 | 3.6
  • Photoshop Elements: 14,13,12,11,10 | 9,8,7 win | 8 mac | 7 mac
  • Premiere Elements: 14,13,12,11,10| 9, 8, 7 win | 8 mac | 7 mac

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• Re-install Windows 7 after the main table and the change of hard disk.

  I had starting problems with my office. If all goes well, a technician isolated the problem and told me that I need a new motherboard, on order right now.

  Once it is installed, and I hope that everything ok, I intend to make use of a hard 'bigger' disc, I bought earlier and reinstall Windows 7.

  I am likely to receive queries from Microsoft during the 'already used product key' and thought, the operating system goes on another computer, what isn't? Microsoft do not use the IP address to identify?

  Second, a new hard drive requires formatting? I remember well the installation of a friend of an OS on a new hard drive has been put in shape was unnecessary, really a case of follow the instructions generated by the CD.

  Once, I am sure that the system works properly, I hope so to follow a command prompt for Windows 10 upgrade.

  Thank you.

  Retail OEM normally is not able to migrate, but die with the first motherboard to be installed on, however, there are reports of MS phone activation of exceptions, so it's interesting to try activating a clean reinstall Windows 7 with this product first key.

  If she rejects the activation, open an elevated command type slui 4, press ENTER, follow the instructions for the activation of the phone, explain to the officer that you have installed the wrong version to see if they will make an exception.

• NB550D - 10G - do I lose the warranty after change of HARD drive?

  I would like to change the HARD drive in my Toshiba NB550D - 10G for one SSD drive.
  Could someone tell me if I lose my warranty after doing this? I would also like to know evolves from 1 GB ram to 2 GB would indeed lose the warranty?

  Thanks for the help!

  No, I think that you that the warranty would be unaffected if you remove and replace the HARD drive.
  The HARD drive and memory are parts extensible user and replace this part will not void the warranty.

• How can I activate CS6 again after changing my hard drive on a Mac (I do not uninstall beforehand)?

  Recently I change the hard drive on my mac but not to uninstall present CS6 thereon.

  How to activate it again? It was a download version of computer applications and I do not have access to my purchase on Adobe CC

  Thanks a lot for helping me

  First of all, you must have your activation published by Adobe

  Don't forget to request ONLY activation support set your number of activations

  Serial number and activation support (no-Cloud) https://forums.adobe.com/thread/2041990

  Then you install programs exactly in the same way you did the 1st time... Launch the installer and enter your serial number when asked

  .

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a way to go to a page to download the Adobe programs if you do not have a disk or drive

  -you will need to enter your original serial number during the installation for non-Cloud programs

  - or kglad links in response to #1 here can help https://forums.adobe.com/thread/2203126

• 2009 iMac has none showing after restore and hard disk crash

  My 2009 iMac running 10.9.5 Mavericks locked up and I had to restore it from backup. After I restored it, it made 2 backups and then crashed. When I tried to restore it again there is no hard drive available. I got when starting was a folder flashing with an exclamation mark. When I started a drive (10.6) there was no available hard drive. The Profiler system showed no applications and no hard drive. Does anyone know how ix, or it is not repairable? Thanks, DJ

  Reboot into Recovery Mode and then reformat the drive of DiskUtility in recovery. Try again.

• Satellite A100-192: after Vista installation HARD disk capacity has decreased

  I am a user of Satellite A100-192 with 120 GB hard drive. After I installed Vista Ultimate, I saw this total capacity of my hard drive completely passed to 92, 8 GB instead of 120 GB while it was XP.

  What can be the problem? How can I reach the other capabilities of my hard drive?

  Hello

  Vista needs and used 2 partitions. The second partition is not visible and it s necessary to Vista backup and restore functions.
  Maybe you have verified that the size of the first partition (C) and didn't note the size of the second partition.

  Concerning