HP Envy 700 PC series: Windows 8 for Windows 10

Similar Questions

• HP Envy 700-414: HP Envy 700-414 Office windows 7 64 drivers

  I didn't like Windows 8.1, because of crashes and recoveries almost every day. So I contacted HP, does not and according to the frustration, I erased the hard drive, disk recovery and all partitions and installed Windows 7 ultimate 64 not knowing not only desktop 700-414 HP Envy Legacy CMOS and HP support don't like no change of. Also, the biggest problem is supported for the HP Envy 700-414 Office windows 7 64 drivers are extremely hard to find, especially drivers LAN Modem, if they exist in HP supports. What can I do?

  Hello:

  This model has the same motherboard as you and has a complete set of W7 x 64 drivers.

  Do not use the BIOS or the files of the firmware of this model on your.

  http://support.HP.com/us-en/drivers/selfservice/HP-envy-700-200-desktop-PC-series/5399651/model/6529898

• HP Envy 700 406 PC: windows 7 drivers for hp envy 700 x 64

  I bought a PC HP Envy 700 406 which had originally windows 8.1 on it, but due to problems of compatibility to work, I had this downgrade to Windows 7 Ultimate 64-bit.  Now I have to get all the drivers to make these computers run smoothly again, but the Internet HP site has only the drivers listed for Windows 8.1 for this PC.  Can someone tell me where to find the drivers I need?

  Hello

  AMD SMBUS driver

  http://ftp.HP.com/pub/SoftPaq/sp65501-66000/sp65990.exe

  Driver USB 3.0 AMD

  http://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69719.exe

  CODEC Audio of IDT high definition (HD)

  http://ftp.HP.com/pub/SoftPaq/sp67001-67500/sp67081.exe

  Alcor Micro USB driver card reader

  http://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69823.exe

  AMD graphics driver

  http://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69692.exe

  RF remote control for viewing slide show and eject pilot

  http://ftp.HP.com/pub/SoftPaq/sp66001-66500/sp66396.exe

  Controller Realtek network driver

  http://ftp.HP.com/pub/SoftPaq/sp67001-67500/sp67085.exe

  Driver LAN wireless Broadcom

  http://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69679.exe

  Driver Bluetooth Broadcom 2070/20702

  http://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69680.exe

• HP Envy (700-420nx): HP Envy 700-420nx Ethernet (network driver) for Windows Server 2012

  I recently converted my desktop (HP Envy 700-420nx) in a server machine PC, running Windows Server 2012. But unfortunately the network stopped working. Then I installed the network (Realtalk) for windows 8.1 driver. But the problems still exist as it is. Says "No correct IP configuration" after an auto repair, "United Nations identified network" on the list of the networks.

  This is why I would like to download the specific driver for Windows server 2012 or any other possible solution to this matter is appreciated.

  Thank you

  Hello:

  See if the driver directly from Realtek works... DL and install the 3rd pilot (4th point) on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• HP ENVY 700-214: map new graphics for HP ENVY 700-214

  OK, so I have a HP ENVY 700-214 (plug here: http://support.hp.com/us-en/document/c04100558 ) and I'd like to get a new graphics card that is compatible with my setup. Everything is wxactly the way I bought it. I want a graphics card that will be easy to install, but also the best in the price range of 200 to 350 dollars. Ive been looking around, but don't can't find anything that tells me what I want to know. Thank you for your time, any input would be apreciated.

  @DudeSame, welcome to the forum.

  This is a great little video card that will fit easily in your case and give you good performance.  However, you need to check to see if power supply (PSU) in the computer unit has a connector 6 extra pins.  Most maps in the price range you want to require at least a connector, 6 or 8 pins or both.  At present, it is out of stock.  You may be able to find an another etailer.  Read the reviews to see what users have to say about it.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• HP ENVY 700-515xt CTO: Windows 7 HD4600 Graphics Crash and recover

  Hello-

  I'm new here and I am also a first time HP customer. I got my new pc for about 5-6 weeks now and have problems with the graphics card crashing and recover. The pilot we (HP Support Tech) installed to try to fix this is:

  Worm 10.18.14.4029 11/18/2014 on the site of HP Software and Driver Downloads, however, the driver that there are listed is actually a version lower than that actually installs. I always get the senario crash/recover.

  Now, I wonder about the Chipset Intel 9 Series driver. Here is a picture of what appears to be using the same driver. Something seems to have updated.

  

  Of course, I would appreciate help on this issue. I had a Support of look of the India on the remote pc, and it is one that has installed the latest graphics driver. I'm sorry to say, but he has not answered all my questions and has scared me with its procedures. Never do that!

  I have a few other occurrences with "sfc/scannow" and something within the control of the diagnostic report Performance/system related to chess and non repairable files, respectively. Please note the failures shown in the following figure:

  

  In advance, I would like to express my gratitude and thanks for any help give you me - thank you!

  Tim

  Great spirits have always encountered violent opposition from mediocre minds

  Hello

  HP has an official presence on this forum other than for administration and moderation. The help you receive is mainly by volunteers.

  I have seen your situation several times based on your description of the SFC is not able to correct the errors. There are operating system and maybe the registry files that are corrupted on your system.

  Try to return to a know good Windows restore point before the problems started.  It's procedure is good for about 1 in 50 when SFC cannot correct errors.

  If you criticize the help on this forum of volunteers so don't expect more assistance.

• HP ENVY 700-059c: 10 Windows cannot set up a homegroup on this computer

  The message I get when I try to put in place a homegroup on this computer is "Windows cannot configure a homegroup on this computer". I tried everything that was suggested on troubleshooting of the forums that I searched the web on this problem but without success. I am trying to create a network with your computer and a Dell 64 bit of Windws 10 laptop.
  Two computers on the same workgroup and I can set up a homegroup on the Dell, but when I try to join the homegroup on the HP I get the same error message. It has been suggested that I have delete the Group residential Dell and put in place a new homegroup on the HP, but HP won't let me set up a new group of residential. Where am I wrong?

  As I said in my last post, I had no chance to get all of my network to the top, but after going through the fixes proposed by WAWood I realized that fixation on the establishment of a group residential wasn't getting me anywhere. I decided to search the web forums for a solution for the operation of "Peer Networking Grouping" of service, something I had not been able to do (strangely enough by clicking on the button 'Start' a billion times has absolutely nothing) since this mess began. Here are the procedures that seemed most likely to have success. First test was to change the registry using a suggestion of:

  http://www.tenforums.com/network-sharing/9691-computer-can-not-join-create-HomeGroup.html

  Modify the key to register IPv6 to enable IPV6
  ==========================
  a. Click Start, type regedit in the search bar and then click regedit in the list programs.
  Note: If you are prompted for an administrator password or a confirmation, type your password or click on continue.
  b. look for, and then click the following registry subkey:
  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\TCPIP6\Parameters
  c. check whether the "DisabledComponents" registry key exists. If so, move on the next steps.
  d. double-click "DisabledComponents" registry key and change the value to 0.
  (If the key does not exist, please create the above key and assign a value of 0)
  e. exit the registry editor and then restart the computer.

  So far no change. On the next dose of:

  http://blogs.technet.com/b/Win7/archive/2011/02/16/quot-peer-name-resolution-protocol-quot-service-could-not-be-started-and-HomeGroup-is-not-working.aspx

  1. from the high CMD prompt, type the following command:

  net stop p2pimsvc /y

  2 delete the following file:

  'C:\Windows\ServiceProfiles\LocalService\AppData\Roaming\PeerNetworking\idstore.sst '.

  3. restart the computer.

  These two patches, apparently has not changed anything, but when I went back to Services and double clicked on grouping network of peers, and then clicked on the 'Connect' tab I found that the "Local System account" is selected and the box "Allow service to interact with desktop" was checked. Since I knew my many visits in this tab that it wasn't the way it was configured initially, I checked the properties of the service directly under it (Peer Networking Identity Manager) the tab 'Connect' showed that this account has been selected, and the term "Local Service" was in the right text box to the right of this account. In the two boxes just below this text box were two boxes labeled password and confirm password boxes contained 14 points. I decided it looked a lot like what I remember that the log on tab of the properties of "Peer Networking Grouping" dialog box has been initially configured. I returned to the journal of Peer Networking Grouping tab and made properties the following steps.

  Chose "This account" and deselect "Local System account".

  "Local Service" text typed into the text box next to "this account".

  Delete all the points in the 'Password' and 'Confirm password' boxes

  Clicked on apply

  Clicked on the tab general and click the button start (Yay he actually started)

  Restarted the computer

  From there on, I was able to set up a homegroup, and then I was able to reach him this homegroup on my laptop connected wireless and viola, I have a network.

  Thanks to WAWood for set me on the path to try to get the 'Peer Networking Grouping' service running as my ultimate goal.

• HP ENVY 700-030qe: BIOS updates for my HP desktop computer

  I have a desktop HP ENVY 700-030qe with Windows 8. While looking through the updates of software available for my system, I have seen two listed in the BIOS:

  (1) HP Compaq consumer Desktop PC BIOS for ROM family SSID 2AF3 dated October 2014.

  (2) HP Desktop BIOS update system for PC HP ENVY 700/800/810 with 2AF3 family ROM dated May 2014.

  1. How will I know what family of ROM BIOS I have? I have pictures of all the screens of BIOS that I could get and nothing mentioned family BIOS ROM. I still have the BIOS original version KAI 80.07.

  2. the two updates apply to my computer? The wording is confusing. It seems that only the second apply to my system unless one applies to a more general category of the office. If both apply, as the first is the most recent, which would be the one to use?

  3. There is an issued for the BIOS in June security update that I ran across here. Which does not appear in the update list. Why would that not replace the other? Can I assume that the October update would include this security update?

  Thank you

  JohnD

  Hello @jpd_az,

  I read your post about how you're looking to update your system BIOS and what version of the software to install. I'd be happy to help you in this case!

  The version of the BIOS, you want to download and install is 80.23 A, which can be downloaded by clicking on the link below:

  • Update BIOS HP Compaq consumer desktop PC (SSID family ROM 2AF3)

  To update this software, I recommend that you follow the steps described in this document on the updates to the BIOS.

  Please re-post with the results of your troubleshooting, and I look forward to your response!

  Concerning

• HP Envy 700-470na: changing the case of the HP Envy 700-470na.

  Today, I upgraded my PSU and GPU for my HP Envy 700-470na. The case for my PC is too small and I can barely sort out the cables.
  
  If someone can recommend a decent case that is less than £50, can put all the pieces of pc HP in the case like the motherboard, hard drive etc and lots of space for the circulation of air and cables. Who would be appreciated! Thank you. I hope that my problem can be resolved soon.
  
  PSU - Corsair CX600M
  GPU - EVGA GTX 970

  The form factor for the motherboard is: Μatx: 24.4 cm (9.6 inches) x 24.4 cm (9.6 inches).  You must buy a case that is made for this.  This means that the accessory in the case must match the holes in the motherboard.  HP has their mothers caught their specifactions cards.  So, they can be standard.  In addition, the connectors in the case may not match the connectors on the motherboard.  The front connector for the power button is the one who comes to mind.  It is very difficult to recommend a case that is certain to work.  You can find the case you like and contact the manufacturer for Technical Support to see if they can make sure it will work for your components.

  Please click on the button + Thumbs up if I helped you and click on accept as Solution If your problem is resolved.

• Want to 700-329: how to switch from windows 8.1 for al profession windows 7 on Envy 700-329

  I'm fed up with the problems resulting from Windows 8.1, for example the program incompatibility, Slow / no response in browsers, particularly IE 11, forced to use touchscreen interface style on conventional monitor and so on and so forth. I have a license of Windows 7 Professional 64 bit for my Dell Vostro laptop. Can I use it on my HP Envy Office 700-329 to replace Windows 8.1?

  Hello:

  It is forbidden to transfer the license OEM of Windows or using product key OEM the Dell laptop on HP desktop computer.

  Please read the FAQ below... specifically...

  Q. my client bought a new PC and wants to move the OEM software from the old PC to the new. Users cannot do what they want with their software?

  A. no, the OEM software is licensed with the computer on which it was originally installed and system is linked to the original machine. OEM licenses are licenses for single use which cannot be installed on more than one computer system, even if the original machine is no longer in use. The 3668Microsoft Software License Terms, that the end user must accept before using the software, say that the license may not be shared, transferred or used concurrently on different computers. System integrators must provide support to the end user for the Windows license on build computers, they cannot support licenses on computers that they did not build. It is a fundamental reason why an OEM System Builder license cannot be transferred.

  http://www.Microsoft.com/OEM/en/licensing/sblicensing/pages/licensing_faq.aspx#fBid=Q44RMvZYHTG

  If you want to buy a license support and installation of W7, you can use the W7 x 74 drivers and the software of this model on your own, except the BIOS and firmware files.

  http://support.HP.com/us-en/product/HP-envy-700-desktop-PC-series/6886619/model/6988376/product-info

• HP ENVY J4W42AA: I need windows 8.1 drivers for my HP - 700-406 ENVY

  I had to install my motherbroad in a new case and I had to use a new hard drive so I need all the drivers for Windows 8.1 drivers. Please help and thank you

  Hello

  Please use the following link:

  http://support.HP.com/us-en/drivers/selfservice/HP-envy-700-desktop-PC-series/7161708/model/7269341#Z7_3054ICK0KGTE30AQO5O3KA30R1

  Kind regards.

• Want to 700-410 W/Beats Audio: HP Envy 700-410 i5 W/Beats Audio, need drivers for Win 7 NO HP SUPPORT

  So just a week after the arrival of my new desktop PC (earlier this year), I had a massive failure of hardrive. I have access in a similar to several corporations hardware industry and had several including a beautiful 248 G SSD kingston hardrives onsite. Having said that I do not think there sucj a problem just install the new SSD in read to send the unit back to HP for repair. I needed this system running and had no time to wait than the lead time of him having returned repaired, about 7-10 days. Yes, it was a huge mistake that has made this system essentially unusable. I did not like the unit running windows 8.1 because it was not a touch screen. I got a new Windows 7 Pro, which I installed it and he posted fine and oots upwards in seconds. No audio beats, but it's not really my thing, no biggie. I can not find information on obtaining network, adapters, Lan, Wan drivers and basically can not access my services Adobe CC, which is my main fucntion. I have since bought a Dell and never have a problem with sys op separate etc.. I return to the problem of tis after several monts and decided I will ive it oe more attempt and them I think Im going to test the aerodynamic viability of this office. I am sure that it will fly ut Im not confident on its ability to land without damage! Please help if you can.

  Hello:

  See if the W7 x 64 drivers of this model works on your.  It has the same motherboard.

  http://h22207.www2.HP.com/us-en/drivers/selfservice/HP-envy-700-200-desktop-PC-series/5399651/model/6529898

  Do not use the BIOS or the files of the firmware of this model on your.

• HP Envy 700-074 Graphics Card problem Windows 8

  Greetings,

  I recently bought the HP ENVY 700-074 (http://http://h10025.www1.hp.com/ewfrf/wc/product?cc=us & dlc = in & lang = to & lc = in & product = 5371495).

  Initial setup went fine without any problem.  I replaced the power supply so that I could add the graphics card from my old computer.  The power supply and graphics card worked perfectly for my old computer.  Feeding is a BFG Tech GX 550 watt modular power supply series.  The graphics card, I have installed is the Nvidia 560ti.

  The problem is that, when I start the computer, my screen goes to sleep (as there is no signal) until the login Windows 8 screen lights up. At this time, my screen lights up and it is normally.  However, if updates or restarts the computer, the screen turns off again and he returned sometimes when loading the desktop computer.  I tried to get into the BIOS to see if I could disable the onboard graphics, but I have been unable to access BIOS because I don't see anything on the screen during startup.  I removed the Nvidia card and returned to the use of the integrated graphics card and everything is back to normal.  I managed to enter the BIOS at the time here, but I don't see any possibility to disable the integrated graphics card or use the PCIe as main display (unless I missed something).

  I also noticed that Windows 8 shows I have 2 screens installed when only 1 is installed physiclaly.  My HP (HP 2009 m) monitor is listed in Monitor 2 and I initially had to go through the windows to get my HP Monitor to display the entire desktop (as it origionally extended from the start, the desktop computer).  However, number of monitor 1 is listed as monitor of generic cards.  Thinking that the computer used the non-existent monitor like main display when starting, I deleted the generic monitor than to have to reinstall windows.  I also tried to disable, but the problem persists.

  I guess that there is a conflict between the integrated graphics card and the Nvidia card.  However, I assumed that the edge will be disabled automatically after inserting a card into the PCIe slot as the integrated graphics card watch is no longer under device mananger.

  Hello:

  Have you changed the settings of the BIOS 2 (required) before installing the video card no HP?

  If this isn't the case, please read the info on the link below.

  http://support.HP.com/us-en/document/c03653200

• HP Envy 700 215Xt: request info for BIOS described below

  I hope I'm posting in the appropriate section, basically a beginner in this room. I have a desktop HP Envy 215XT 700 with Windows 7 Pro 64 Bit OS. My interest is in the BIOS, and basically, I want to understand better. What I would like is to have a manual or guide for this BIOS, if there is such a thing. For example, if you have more than one drive installed, or even the DVD drive and HDD, other places to start from, if bring you up the BIOS screen, then select F10, you can select a boot device. You can also do this in F9. I have to do one, two or what? And in what order. I'm starting to think that this computer does NOT like the 2 discs hard bootable installed, period. A bootable, one works better,

  2AF7 system board / Cfg, ID 1.00 product / Bios Rev MEM v80.16 / CPU Intel core 17-4771 3.50 GHz cpu.

  1 can or I would be able to run (2) 1 terabyte drives in the computer, and can both be bootable or just one?

  2. does anyone know if there is a BIOS update or a newer firmware to do this, my opinion is not.

  3. I have here available, a person, a sort of User Guide with details of Setup when using this BIOS to go n informed approach?

  Thank you.

  John

  [email protected]

  Hello jpw389 ;
  
  Let me welcome you on the HP forums!
  
  I read your post on the BIOS info and wanted to help.
  
  You can have any number of disks bootable on a PC, but the BIOS has a defined order in which he sees these readers, and it will attempt to boot an OS in that order.  So, with more than one bootable disc to begin the second drive, you must do one of the following:

  (1) change the order of the drives in the list of the BIOS to move the other drive to the top of the list

  2) press the function key that allows you to select a drive to boot from

  The difference in the use of these two is that the first change is permanent, the second for a boot.

  Regarding versions of BIOS, the link is on the Page of the product HP to Win7 for your PC: http://support.hp.com/us-en/drivers/selfservice/HP-ENVY-700-Desktop-PC-series/5399651/model/6667346

  Under the BIOS section, you will see two updates to the BIOS.  You can check yours to see what version of BIOS uses at present.  There is no other update BIOS.

  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• HP ENVY 700-029eb desktop PC. Update to Windows not sure 8.1?

  Hello world

  HP ENVY 700-029eb-computer for office
  Model: E3H39EA

  Windows 8

  A question related to the following message on my HP computer:
  -----------------------------
  HP has not tested this PC with Windows 8.1
  For this reason, HP is unable to update providence instructions or Windows 8.1 drivers.
  You can now lose stability and basic functionality if you try to update your system.
  -----------------------------

  A Windows 8.1 update could make the System unstable, so the message of HP.

  But my computer is always busy preparing the update and guard asks me to do the 8.1 update.

  So can I install Windows 8.1 safely on this computer? Or how to turn off the update?

  We appreciate your comments and advice.

  GuyterB1964, welcome to the forum.

  I do not understand these messages.  Here is the download page for software and driver for the computer.  As you can see, all the drivers for win 8.1 are listed.  They would not list them as much as they have not been tested.  I see no reason not to do the update.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.