HP envy pro 4-b000

Similar Questions

• Bios\admin reset password HP Envy pro 4-b000

  If possible could you please help unlock my computer. Its a HP Envy pro 4-b000 and after 3 attempts I get the number "59738431" any help would be greatly appreciated.

  Thank you very much for your help.

  Try j.

  46690417

  Use this code to go into the BIOS.

  Disable all passwords that are enabled.

  If demand for CURRENT password using this code.

  Request NEW password just press ENTER.

  If asked to hit just to CHECK password to enter.

  Save and exit.

  REO

  I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.

• HP ENVY Pro 4-b000: what is the port of hard drive on my laptop?

  I was going to upgrade to an SSD, but I need to know what is the port for the hard drive?

  P/N: B8W17AA #ABA laptop

  grizzogor

  Hello;

  Let me welcome you on the HP forums!

  Sorry but I don't understand your reference to a 'port' for the hard drive.  A 'port' is typically a connector on the case of a laptop when you plug a cable any in.  And, in this sense, there is no "port" for the hard drive.

  This link is to the Service and maintenance for your PC Guide: http://h20566.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=5271152&docId=emr_na-c03404932&docLocale=en_US

  Information hard disk, as well as the replacement instructions, begin on page 37.  Understand, though, that this isn't a deletion-the-cover, ease of use; Instead, you must disassemble the laptop.  Unless you are experienced in doing that, my recommendation is to have the disk swap is completed in an HP Service Center.

  Here is information on Service Centers: http://support.hp.com/us-en/document/c00372730?jumpid=reg_r1002_usen_c-001_title_r0004

  Here are a few troubleshooting steps you can try:

  Good luck

  ========================================================================
  I'm a volunteer and I do not work for, or represent, HP.
  ---------------------------------------------------------------
  Please click on 'Accept as Solution' on the post that solves your problem to help others to find the solution.
  Please click on the symbol of the thumbs-up to the left of the answer key to say thanks fopr my help.
  ========================================================================

• ENVI Pro: Want Bios administrator password

  Hello

  I have a laptop with administrator password of bias.

  I received the code (59244637)

  Can someone help me

  Thanks in advance

  Please enter = 46122219

  Steps to follow after you have reset the password:

  1. Use the posted above unlock code to access the BIOS
  2. Disable all passwords that are enabled
  3. If current password request - type the unlock code
  4. New password, simply press the ENTER key
  5. Repeat the same thing to check the password column.
  6. Then exit the BIOS saving & exit option to save the changes.

  Troubleshooting steps:

  Incase if the password does not work please try a Hard Reset as follows.

  1. Shut down the laptop
  2. Disconnect the power adapter and remove the battery
  3. Hold down the Power button for 30 seconds
  4. Plug the power supply/AC adapter (leave the battery for now) & start Notepad
  5. If now see you a password, please enter the same password I've shared before and press on enter

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the button white Thumbs Up on the right of say thank you*.

  Make it easier for others to find solutions by checking a response "accept as Solution" if it solves your problem.

  Thank you

  KNRK

  Although I am an employee of HP, I speak for myself and not for HP

• HP ENVY 15-j142na: HP ENVY 15-j142na Samsung 950 PRO NVMe m2 update?

  Support HP ENVY 15-j142na Samsung 950 PRO NVMe m2 dose?

  Negative results. There a WSSD but it is the older form factor, not m2 and even the old player of WSSD type may not be bootable is a cache acceleration only.

• 8.1 Windows Pro update the problem (from Windows 8 Pro) on Envy 23 TouchSmart all-in-One...

  Hello

  I have a HP Envy 23 Touchsmart all-in-one that I bought a year ago (12/2012). It comes preinstalled with Windows 8.

  System information:

  (a) Intel (r) Core i7 - 3770 S CPU @ 3.10 GHz

  (b) 8192 MB of RAM

  A few weeks after that I had bought the system, I've upgraded to Windows 8 Pro with Media Center that I bought through Microsoft upgrade program.

  Last week (19/10/2013), I saw the option upgrade to Windows 8. 1 in the store and decided to upgrade.

  After a few minutes, I got a prompt asking me to restart the computer, and I did.

  However, I noticed that the screen has turned white, but it restarts not really - I have seen that the hard drive light was still flashing and I waited for about 15 minutes. I know it does not restart because if that were the case I would have seen the HP logo on the screen of the BIOS. A little later, the system entered into mode 'sleep' (at least the light blinked slowly as if it was the sleep). As it was late at night, I decided to leave the system alone and decided to check on it the next morning. The next morning, he was still in mode 'sleep' (as I feared) - when I tried to wake up from her sleep by moving the mouse/hit the return key, he did the exact sounds as if he were to wake up from its sleep (as it always does), but the screen is still blank. The light power button lit up constantly indicating he's awake now.

  At this point, I decided to turn off the system by holding the button for a few seconds. To restart, I saw the HP logo on the BIOS boot screen and the screen went white and nothing came.

  So I decided do a system recovery using my Windows 8 recovery CD and turn off the system with the CD in its niche. This time, the system came and began immediately to restore my OS to a previous version.

  After connecting to the system recovered, I received the following message:

  "Could not update for Windows 8.1.

  Sorry, we could not complete the update Windows 8.1. We have restored the previous version of Windows on this computer.

  0xC1900101 - 0 x 40019.

  I tried to reinstall Windows 8.1 a couple of times after that. Once to disable all non-Microsoft services and disabling all startup programs. Always the same result.

  I have no antivirus software on my other system protection of Microsoft default system software.

  Any help, greatly appreciated.

  Thank you.

  I have disabled active secure boot existing starter and the update worked.  Now we get the error of watermark "secure boot not configured correctly.  But I have re-enabled secure boot and the error disappeared.

• Upgrade Windows 7 to 8.1 Pro for HP Envy 810 - 145qe (J0X43AAR #ABA)

  I just bought a HP Envy Phoenix 810-145qe which is preinstalled with Windows 7.  Specifically, I bought this system because it was faster than my old desktop processor and I could spend 24 GB memory to 32 gb that I did.

  I went to the HP site and checked if this model has been tested by HP that came back had not been tested with Windows Pro 8.1.  Can someone tell me if I've stuck with Windows 7 on this new machine?  I really need to have Windows Pro 8.1 because I develop e-Learning programs that need to be tested in an environment Windows OS 8.1. Please notify.

  Hello

  I don't see a problem with the installation of Windows Pro 8.1 on the 810-145 envy.  HP has released drivers for Windows 8.1. There is little difference between Windows 8.1 and Windows Pro 8.1.

  1. Check with the manufacturers of your application to make sure that you don't have a problem with Windows 8.1
  2. Run Microsoft Windows 8 upgrade assistant
  3. Don't forget to create the external HP recovery media.
  4. Back up your data and also download drivers HP Windows 8.1 posted on external media.
  5. Buy licensed Windows 8.1 and download Microsoft support.  The Microsoft download process will allow you to create a bootable USB flash drive or an optical medium.  I would recommend that you download the ISO support and then create the desired boot media.
  6. Follow these instructions from Microsoftto install Windows 8.1.

• Downgrade to windows 7 Windows 8 pro Hp Envy dv6-1090ee

  I recently bought a new Hp dv6-1090ee envy which has windows 7 preinstalled. I used the offer to upgrade to windows 8 pro for $ 14.99, but I did not like the new interface of windows 8 and I would go down to my original windows 7 with the factory settings.

  I checked the multiple sources in the best way and more confused when I started has finished. I really hope I can get the best solution here or at least performed on the best site where I could follow the appropriate directions.

  Some useful information:

  I have upgraded to windows 8 pro and did not have a facility clean (I still have a windows.old folder).

  I don't have a recovery disc for my windows 7.

  I don't remember the version of windows 7, I had.

  I have an old windows 7 installation disc, but I don't know the product key provided for windows 7 with the laptop.

  I just wanted to say that I could solve my problem with a very simple method. I contacted HP support through my HP support assistant at home and the solution was much easier than I anticipated.

  Since I've only updated, I still had the windows.old folder. so, I followed the following procedure:

  1 restart my pc.

  2. press F11 before that windows 8 has begun.

  3. the Recovery Manager open.

  4. I chose to restore the computer to factory without backup (since I had already backed up all my data on a Portable hard drive previously).

  5. the Installer started and the computer was still brand new.

  Everything worked well. Thank you HP support.

  It is a solution to my personal problem and on my model, I don't know if it works on all new HP laptops. My best advice for anyone with a problem is to contact HP support through HP support assistant, it is a very useful tool.

• No 1110ea audio envy 15 after installation of windows 8 64 pro

  No sound on my 1110ea envy 15 after installation of windows 8 64 pro.

  Maybe the audio drivers hp are repaced by victory 8 drivers?

  ass pls

  Hello

  Try the driver from the following link and see if it works...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?cc=us & LC = on & DLC = in & softwareitem = ob-113849-1

• HP ENVY M6-1106er: Windows 8 Pro hang up to begin after adding Hyper-V role

  Hello.

  Have a problem with HP ENVY M6-1106er

  After the OEM Win8 upgrade to the Pro version, I added the Hyper-V role for my system and restart the laptop.

  After the restart boot OS freezes on the screen with the HP logo and rotating circles.

  If I disable AMD Virtualization in the BIOS - system starts, but the hypervisor does not work.

  With virtualization enabled in the system BIOS will not start with the Hyper-V role installed.

  Help, please.

  Hello Sir,

  Here's what you need to do.

  1. enter in the BIOS setup and define virtualization as being disabled and reboot the system.

  2. after starting windows 8, enter the control panel and remove the bluetooth driver.

  3. download and install Ralink Bluetooth driver 9.2.101.10 version (SP59632)

  4. restart the system and reactivate the virtualization technology.

  I hope this helps.

• HP ENVY 17 Notebook PC: Can't activate Windows 8 Pro after a factory reset (hard drive reformatted).

  Hello:

  I had to make a drastic clean the C drive of my ENVY 17 laptop and did a Factory Reset. I was able to reload Windows 8 Pro to my USB stick recovery.

  However, Windows 8 Pro cannot be reactivated indicating that the product key is invalid or blocked. I understand that this is due to having the OS completely cleaned and formatted drive.

  My questions are:

  1. Will be the HP (which is available on order) recovery disks be able to help solve the situation described above?
  2. It will allow me to reactivate my Windows 8 Pro?
  3. Will the recovery be HP discs/media contain or are marked with the correct Windows product key?

  Thank you

  Rico.

  Solved! HP technical support took care of me Thank you so much.

• Want to 24-n075na: upgrade to Windows 10 Pro on Envy 24-n075na All-- One PC in

  I tried to upgrade to Windows Pro 10 on the Envy 24 - n075na all-in-One PC of Windows 10 Home. He can't be upgraded.  It seems to go through the process of upgrading shutsdown and restarts and then displays a message that says: it could not be upgraded.

  Any ideas.

  Thank you

  I thought about it. It was mcaffee blocking the upgrade. Remove and the update worked fine!

• HP Envy & LaserJet Pro: A free way to Fax

  I have two printers. An all in one LaserJet Pro and envy and I'll try to find a free way to fax.
  
  I checked the application here is a nun for faxing.
  
  So does anyone know of an Android App, free app Windows 10 or way in the browser of Fax?

  Although fax programs are beyond my scope of support, I would like to do everything I can to help. Since you can't scan to PDF and only have the option to scan as an image, I suspect that there is a problem with the software and suggest to uninstall and reinstall. Maybe, if you were able to scan in PDF, you should be able, you would be able to use the fax you program found.

  Concerning fax communication problems, you've been through, I suggest you take a look at the following document to make sure that you have done all the recommended solutions: products of Fax all-in - One HP - impossible to send or receive faxes: troubleshooting fax problems.

  Given that faxing is intermittent, I also recommend you call your phone provider to see if they can perform tests of line.

  I hope this helps.

• HP ENVY m6 1158ca: Windows 8 Pro Setup own activation fails 0xC004C003 blocked by OEM product key

  My hard drive died on my HP ENVY m6 1158ca.  I replaced and ran 6 discs recovery I created for my daughter and

  After the last completed album, I hit continue to do construction and each time after several reboots (ready devices... Prepares... ... Software administrator is installed) it would get the BSOD - 0xc000000f - a required device is not connected or not available.  SO I format the disk of 1 TB and do Factory reset again, and it still fails in the same way.

  After failing on several occasions, I've used a Windows DVD Pro 8 for another HP laptop and Windows 8 coming!

  However, the activation of Windows 8 needs a key I guess that the BIOS it will not work.

  Call Microsoft by using the "activate Windows by phone" gave rise to the statement "you must call OEM.

  to get a key and then call us back and then we can help you"

  The HP ENVY is out of warranty, who do I contact to get this key on the BIOS?  or the BIOS button does not work

  because the Windows 8 Pro does not correspond to something?  The laptop came originally with Windows 8.

  Thanks in advance for any help,

  Marlene

  Hi @ml88,

  Welcome to the HP Forums! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  The product key that is embedded in the BIOS may not work with the version of Windows 8 Pro.

  Here is a document HP-HP System Recovery troubleshooting (Windows 8) computers you can review. It can help restore the system from the recovery disks.

  If you need to get the recovery media:

  HP computers - get HP recovery disks or HP USB recovery disc

  Let me know how it goes.

  To say thank you, click on the "thumbs-up". Accept the post as a solution, if your problem solved, so that other people have the same problem can see it.

  Kind regards

• HP Envy 23: How can I install Windows 7 Pro Windows 8.1 pre-installed slim like 23?

  Hello... I HATE 8.1... but I saw your list of wonderful driver for your laptop and I was wondering if it is similar to a HP desktop computer when removing windows 8.1.   I already asked HP for help, but they, unfortunately, are "unable" to tell me that I can even load Windows 7 23 want.  People very nice, but very limited information.

  I managed to find 2 new copies of Windows 7 Pro, more a have on hand software... obviously, until Windows has the world dislikes phone applications on a computer, we need backup copies!

  My brand new mess is a HP Envy 23 I just bought last Sunday and hates carefully.

  I got the USB backup, just in case, but to wipe the drive (if I can) and change the boot order (if I have will be tolerated), and of course, eliminating all additional platforms I could find if this is possible)... What do I need to save the facility from 8.1 to make bits andpieces and love its color and whatever work?

  And what on Earth is UEFI?

  Thanks in advance... I know that this forum is a labor of love.

  Six days in a 30 days return... Help!

  Knowing the complete model of the computer help, HP Envy 23-xxxxxx

  Try to downgrade your system would probably void your warranty and a challenge trying to find drivers that would work with Windows 7, a real headache.

  If you want to go this route, you need to disable secure boot and enable legacy in order to change the boot order.

  It may be easier to keep what you have and make it Windows 8 look like Windows 7

  http://www.eightforums.com/tutorials/50124-Windows-8-1-make-look-feel-like-Windows-7-a.html

  or this:

  http://www.MakeUseOf.com/tag/make-Windows-8-8-1-look-like-Windows-7-XP/