HP G60 - 235DX NOTEBOOK PC: System Restore
Did a restore of the system with the recovery cd, and then click Finish now the screen installation software hp continues to come and stop
Did you do a Factory Reset with the recovery discs? If this is not the case, do.
When you did the recovery discs?
Why do you restore?
Tags: Notebooks
Similar Questions
-
HP G60-235DX notebook pc does not recognize the drive d (cd - dvd drive)
I'm reading a music cd in d drive. My computer does not recognize the drive. I can solve this problem?
Press the Windows Logo key and the R key to open the run.
Type; regedit, and then click OK
Navigate to:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
With the right button of the upper filters button, if necessary, and then click 'remove '. Click on the Yes"" button.
Click the lower filters key, if present and click 'delete '. Click on the Yes"" button.
Try again your CD.
-
System Restore DVD Vista vs Windows 7
I'm new here and I apologize if this has been asked before. I looked around and tried to search but can't find my answer.
I just reveived my new HP Pavilion dv7t last night. Notebook Essentials booklet says to create a set of DVD system restore, but This can only be done once. I am in the process to register for the upgrade to Windows 7 snce is expected within a week.
Should I go ahead and create the restore DVD system with the Vista operating system, and if I do I then will be able to create another System Restore DVD for Windows 7?
I want to assure you that I have a restore of the system based on both operating systems, where I need to go back to Vista, but still have a system for Windows 7 restore, if it proves to be stable and I like the OS.
I hope this makes sense...
Make your Vista recovery DVD. Two reasons...
1. you will not be able to do a cover of 7 Win set, (unless, of course, HP offers a magic here).
2. If you install Win 7 and you need to reinstall it later, you will have to start with the Vista installation and repeat the upgrade process (unless HP upgrade version works differently from the retail... version did not get a response on this one here).
Of course, you can always use an application of imaging to make an image of the newly installed Win 7 to use in the case of a reinstall. Acronis True Image or Macrium Reflect are 2 choices. Macrium is my preference.
-
NEED DRIVERS AFTER SYSTEM RESTORE
HP Pavilion g6-2128tx Notebook PC
Serial number: 5CD2231LJF{Information}
After system restore a bunch of drivers was missing, I managed to update some drivers but I need some I can't find. Help!
Hardware ID
Ethernet controller:
PCI\VEN_10EC & DEV_8136 & SUBSYS_183E103C & REV_05
BCM20702A0
USB\VID_0A5C & PID_21E3 & REV_0112
PCI device
PCI\VEN_10EC & DEV_5229 & SUBSYS_183E103C & REV_01
PCI Simple Communications controller
PCI\VEN_8086 & DEV_1E3A & SUBSYS_183E103C & REV_04
SM Bus controller
PCI\VEN_8086 & DEV_1E22 & SUBSYS_183E103C & REV_04
(USB) Universal Serial Bus controller
PCI\VEN_8086 & DEV_1E31 & SUBSYS_183E103C & REV_04
I run on Windows Ultimate-64-bit
Help would be GREAT
Hello
Download and install the following.
After this Setup is complete, restart the laptop.
Intel Management Engine Interface.
Intel USB 3.0 Host Controller Driver.
Kind regards
DP - K
-
System restored automatically after the installation of updates & a few missing desktop icons.
Original title: same set of updates on both computers due to different problems, one problem being a system restore.
I have two Windows 7 computers in my house. They all have two problems after installing updates a month ago. The problem for 'Computer 1' is a bigger problem than the problem of the "Computer 2". 2 computer problem not really seems to be a problem now, but I'll give you the information for comparison purposes. Sorry for the length of this post - I am trying to be thorough.
1 COMPUTER DETAILS:
News of the computer: Dell Studio 1745 laptop computer running Windows 7 Home Premium 64 bit, six months at the time of the problem, now age of seven months. It came with Norton pre-installed, never used and uninstalled. Trend Micro Internet Security installed at the beginning of the use of the computer. Analyses Micro trend came clean.
Background: set up with a single account (Administrator, of course) and after a few days of putting in place computer, said ale user account for everyday use. Computer is configured to warn me before downloading/installation of updates of Windows, with permission for each type of account to install Windows updates.
While in the standard account, I welcomed these download/install updates and was prompted to restart the computer. I was done with the computer, so I just closed instead of restart. According to "Your update history Review", it's updates and they were all successful:
Update for Windows 7 for x 64-based systems (KB980846)
Microsoft .NET Framework 4 Client Profile for Windows 7 x 64-based Systems (KB982670)
Update for Windows 7 for x 64-based systems (KB982519)
Update Microsoft .NET Framework 3.5 SP1 for Windows 7 and Windows Server 2008 R2 for x 64 systems (KB982526)
Cumulative update for Media Center for Windows 7 x 64-based Systems (KB981078)After you turn on computer back, everything seemed normal. I opened Firefox and I got a notice that Firefox has an update is available, a standard user cannot. Unlike some programs, there is no popup to sign as an administrator, so I went to start > switch user and signed as an administrator. (There was no update of Firefox at this point - just a switch single user.) That's where the problem appeared: instead of normally load the admin Office, I had to wait while Windows configured my desk (it's new)... wait... wait... wait... wait... BAM! Your computer has been successfully restored * insert date here * (I don't remember what it was - January of this year, perhaps - because I was so incredulous that it happened and I continued to watch the game "successfully restored"). I do not have the computer to eat, and it don't has not asked me if I wanted to restore it. He just did, just on its own initiative, when I went on the admin account. A bunch of shortcut icons are missing from the Office of the admin acct and the ACCT. standard, and wallpaper to the admin account has been changed. I am not absolutely sure if nothing else was touched.
I have searched online to try to understand why it happened, and I remember well from my only find, is that if I went to the restoration of the system, there will be an option to cancel it, but I don't see such an option. So I told the computer to eat on a few days to a week before that updates. It doesn't seem to help. Shortcut icons are still missing. Looked at the update history and it shows the five latest updates as being installed successfully, but Windows Update tells me that I need to these five updates AND this time, the little check marks are only already there on four of the five updates listed. (The first time, the little checkmarks were already there for all five.) This is the update that is NOT now pre-checked:
Microsoft .NET Framework 4 Client Profile for Windows 7 x 64-based Systems (KB982670)
Do not reinstall the five updates. I don't know if I should jump install them again, or if I should install only the
now, four are already "pre-checked." I'm very hesitant to install KB982670, because this update seems to be the likely cause of the problem given the fact that it is already pré-coché in the Windows and the following information updates for computer 2.Since I installed the latest updates for 1 computer with no apparent problems:
X 64-July Windows malicious software removal tool (KB890830) 2010
Update security for Windows 7 for x 64-based systems (KB2032276)NEWS ON COMPUTER 2:
The computer news: Systemax desktop running Windows 7 Professional 64-bit, a month at the time of the problem, now age of two months. It has not come with any pre-installed antivirus. Trend Micro Internet Security installed at the beginning of the use of the computer. Analyses Micro trend came clean.
Reminder: Set up immediately with an admin account and a standard account for everyday use. Computer has been set to automatically download and install updates for Windows, but is about to inform me first.
At the time of the problem above with the laptop, desktop computer has been enabled. As all loading,.
an error message came that there was some kind of issue with the .NET framework. At another person asked if he knew what was up with that, and it didn't. Did not note the specific message, thinking he would tell me again if there was a real problem. I thought it could have been some kind of Windows hiccups when starting the computer, not even knowing about update problems. I have yet to see this message. After the number of laptop (computer 1), I took a peek at the desktop computer (computer 2) to check that Windows Update and I saw that an update is available, which is the referenced above same update that the notebook had already the check mark in its box (KB982670), which gives me the choice to check the little to install it. Very curious, since, as already mentioned, the computer has been configured to automatically download and install Windows updates. Looked at the update history, and it has already downloaded and installed the other four updates that the laptop has been. Changed the automatic Windows Update setting to warn me before you download and install updates. I have not installed the missing update. Said the only other person in the House who would probably bother install updates to not install it.A month later, 2 computer has a notification from Windows update that 21 or 22 updates are available (as a result, by clicking on the icon of the trial of Microsoft Office). The update not installed a month ago is no longer on the list, and update history shows as having been installed a few days before, apparently because someone else in the House must have thought it looked like a good idea. I installed all the 'important' updates and have not seen any more problems with computer 2.
BACK TO THE COMPUTER 1:
Yes, is there anyone with ideas on how to get 1 computer back to its state before the 5 updates listed above, and what to do about to reinstall some or all of them, I hope, without more problems, for example a random food system does not happen? I have a feeling I will say that the random system restoration do not occur, but he did.
Thanks for any help.
No, I don't use the Norton removal tool.
IN RE COMPUTER 1 ONLY:
1. download the Norton Removal Tool, save it to your desktop: ftp://ftp.symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe
2. close all open applications (that is, anything with an icon on the taskbar).
3. click right on the file saved in #1 above, and then select run as administrator to run the utility. DO TAP not your keyboard until the race ends, then restart.
4 for good measure, reset Windows Update by...
How to reset the Windows Update components?
-Online skip the section to APPLY to; KB971058 access via I8 32-bit only; Run the difficulty in DEFAULT and modes, then AGGRESSIVE [1]
http://support.Microsoft.com/kb/9710585. restart & test.
~~~~~~~~~~~~~~~~~~~~~~~~
[1] full Disclosure: the difficulty operating in AGGRESSIVE mode will delete your update history (but not list updates in the updates installed)~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft
-
I try a system restore on my laptop HP dv7t-2000. I started restoring from disk hard partition, i.e. System Recovery Manager, Advanced Options, system recovery, etc. (as described on page 33 of the booklet that came with the computer when I bought HP Notebook Essentials). The computer tried to restart but seems to be stuck at a blank screen with a blinking cursor on the upper left side of the screen. I'll leave it alone for several hours, but fear that the restoration has failed. The restoration will return to the orginial, Vista operating system that I've upgraded to Windows 7 with a RESUME provided disc. Suggestions?
Attempt of Mrs.
I repeated the restoration of the system from the hard drive and the second time the restore worked.
-
When I open the System Properties dialog box, System Restore is checked, saying: she is disabled by group policy, and the system you cannot activate this option. I got a partition dedicated to my justo of hard disk to store backups and create Points of restoration with a capacity of 10 GB. How can I solve this problem?
If you see things like this:
You do not have sufficient security privileges to restore your system.
The System Restore tab is missing from the my computer properties.
System Restore has been disabled by group policy. To turn on system restore, contact your domain administrator.
The System Restore tab is available, but the turn off System Restore (disabled by Group Policy) box is grayed out.
The task manager has been disabled by your system administrator.
The registry editor has been disabled by your system administrator.
The task manager has been disabled by group policy.
The registry editor has been disabled by group policy.
The command prompt has been disabled by your administrator. Press a key to continue...
The operation has been cancelled due to restrictions in effect on this computer. Please contact your system administrator.
The "Run" option is missing from the start menu.
The option "Log off."... ' is missing from the Start Menu.The usual advice are something in the sense of "something has been disabled in the group policy...". ", and it is probably true that something has been disabled, but you know what something is and what it takes to do about it.
If you are using XP Home Edition, you will get away with advice to use the Group Policy Editor, because there is no Group Policy Editor in XP Home and that really doesn't tell you where to look in group policy, even if you run the Group Policy Editor.
You need a complete solution that works for all versions of XP and requires no hunting around in the Group Policy Editor or registry to find where things are that have been disabled.
Unless you have disabled these things on purpose, chances are good that your system has a malware infection. The malware knows what tools you use to try to find and remove, for the malware disables the things you are more likely to consume and prevents them from running if you can't find the malware and remove it.
If your system has this kind of affliction, all malicious software tools you currently use or have used failed to protect your system so that you can expand your horizons malware detection and prevention to prevent these kinds of afflictions in the first place.
The malware will be happy you trick into thinking that you need to so something drastic to fix your system - as a facility repair, system restore point or a total reinstallation of XP. This is what it would be like you, but these measures are not necessary.
You must solve the immediate problem of the tools does not, then scan your system for malware when you are finished.
No matter what kind of malware you've used analytical tools, they are unlikely to solve this problem, because they cannot tell if the changes made to your system have been on purpose (you or an administrator who makes them) or some malware changed them, so the analysis tools will let these things alone (it's usually a good thing).
If your system is afflicted in this way, there are probably other things that also do not work - like the Task Manager, the registry, System Restore and command prompt Editor, so fix them all at once even if you have not discovered they are broken again.
These commands from registry removes the registry entries that are stop opening programs. Although the registry entries do not exist, these commands are safe to run and will work for all versions of XP.
Before making any changes to your registry, back up the registry with this free and popular tool:
http://www.SnapFiles.com/get/ERUNT.html
Open Notepad to create a new text file:
Click Start, run and enter in the box:
notebook
Click OK to open a new Notepad file.
Copy and paste the following lines of text into the new Notepad file.
Windows Registry Editor Version 5.00
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\System]
"DisableTaskMgr" = -.
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\System]
"DisableRegistryTools" = -.
[HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\System]
"DisableCMD" = -.
[HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindowsCurrentVersionPoliciesSystem\\\]
"DisableTaskMgr" = -.
[HKEY_USERS\.default\Software\Microsoft\Windows\CurrentVersion\Policies\System]
"DisableTaskMgr" = -.
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon]
"DisableCAD" = DWORD: 00000000
[HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows NT\SystemRestore]
"DisableConfig" = -.
[HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows NT\SystemRestore]
"DisableSR" = -.
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoRun" = -.
[HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoRun" = -.
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoClose" = -.
[HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoClose" = -.
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoSetTaskbar" = -.Save the new text file with extension .reg on your desktop or somewhere you can remember with a name you can remember, something like:
enableit.reg
After you save the file, close Notepad.
Locate the file enableit.reg on your desktop and double-click it.
Alternatively, you can right-click on the enableit.reg file, choose open with... and select the registry editor.
Answer in the affirmative to the question... Are you sure you want to add the information in the registry?
You should then see a message that information has been registered in the register.
Reboot your system and test.
You can delete the enableit.reg file when you are finished.
If the registry editor has also been disabled, we first fix (not a problem).
Given that your system has or has had an infection, follow up with this:Perform scans for malware, and then fix any problems:Download, install, update and do a full scan with these free malware detection programs:Malwarebytes (MMFA): http://malwarebytes.org/SUPERAntiSpyware: (SAS): http://www.superantispyware.com/They can be uninstalled later if you wish.For the benefit of Microsoft technical support engineers, here are some ideas offered in the past which does NOT help with this issue:
Safe Mode boot
Last good known Configuration startup
A clean boot
Sfc/scannow in running (or trying to run) -
"System Restore checkbox is disabled (through Group Policy)"
Where can I ask a question ' how can I turn on system restore which is disabled by group policy?
I turn off System Restore by using these steps. Right click on my computer-> properties-> system-> clicked restore on turn off System Restore check box.
Using the same way, that I can not activate it because the box is disabled (through Group Policy).
Please help me solve this problem. Thanks in advance.
It's too bad the Answers MS deficient of remains of forums in that it does not prompt for any system information when a new question is asked, that's why we don't know anything about your system.
If that's what you see and you do not have it to yourself, your system is currently or has been infected by malware.
You can solve the immediate problems, but I would not use system restore to solve any problems your not specified, it (but it's up to you).
Here are the suggestions that you might see will not work (just so you don't waste your time) and then how actually to solve this problem.
The usual advice are something in the sense of "something has been disabled in the group policy...". ", and it is probably true that something has been disabled, but you know what something is and what it takes to do about it.
If you are using XP Home Edition, you will get away with advice to use the Group Policy Editor, because there is no Group Policy Editor in XP Home and that really doesn't tell you where to look in group policy, even if you run the Group Policy Editor.
You need a complete solution that works for all versions of XP and requires no hunting around in the Group Policy Editor or registry to find where things are that have been disabled.
Unless you have disabled these things on purpose, chances are good that your system has a malware infection. The malware knows what tools you use to try to find and remove, for the malware disables the things you are more likely to consume and prevents them from running if you can't find the malware and remove it.
If your system has this kind of affliction, all malicious software tools you currently use or have used failed to protect your system so that you can expand your horizons malware detection and prevention to prevent these kinds of afflictions in the first place.
The malware will be happy you trick into thinking that you need to so something drastic to fix your system - as a facility repair, system restore point or a total reinstallation of XP. This is what it would be like you, but these measures are not necessary.
You must solve the immediate problem of the tools does not, then scan your system for malware when you are finished.
No matter what kind of malware you've used analytical tools, they are unlikely to solve this problem, because they cannot tell if the changes made to your system have been on purpose (you or an administrator who makes them) or some malware changed them, so the analysis tools will let these things alone (it's usually a good thing).
If your system is afflicted in this way, there are probably other things that also do not work - like the registry editor, System Restore and the command prompt, so fix them all at once even if you have not discovered they are broken again.
These commands from registry removes the registry entries that are stop opening programs. Although the registry entries do not exist, these commands are safe to run and will work for all versions of XP.
Before making any changes to your registry, back up the registry with this free and popular tool:
http://www.SnapFiles.com/get/ERUNT.html
Open Notepad to create a new text file:
Click Start, run and enter in the box:
notebook
Click OK to open a new Notepad file.
Copy and paste the following lines of text into the new Notepad file.
Windows Registry Editor Version 5.00
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\System]
"DisableTaskMgr" = -.
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\System]
"DisableRegistryTools" = -.
[HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\System]
"DisableCMD" = -.
[HKEY_LOCAL_MACHINESOFTWAREMicrosoftWindowsCurrentVersionPoliciesSystem\\\]
"DisableTaskMgr" = -.
[HKEY_USERS\.default\Software\Microsoft\Windows\CurrentVersion\Policies\System]
"DisableTaskMgr" = -.
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon]
"DisableCAD" = DWORD: 00000000
[HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows NT\SystemRestore]
"DisableConfig" = -.
[HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows NT\SystemRestore]
"DisableSR" = -.
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoRun" = -.
[HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoRun" = -.
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoClose" = -.
[HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoClose" = -.
[HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer]
"NoSetTaskbar" = -.Save the new text file with extension .reg on your desktop or somewhere you can remember with a name you can remember, something like:
enableit.reg
After you save the file, close Notepad.
Locate the file enableit.reg on your desktop and double-click it.
Alternatively, you can right-click on the enableit.reg file, choose open with... and select the registry editor.
Answer in the affirmative to the question... Are you sure you want to add the information in the registry?
You should then see a message that information has been registered in the register.
Reboot your system and test.
You can delete the enableit.reg file when you are finished.
If the registry editor has also been disabled, we first fix (not a problem).
Then, you should do this:
Perform scans for malware, and then fix any problems:Download, install, update and do a full scan with these free malware detection programs:Malwarebytes (MMFA): http://malwarebytes.org/SUPERAntiSpyware: (SAS): http://www.superantispyware.com/They can be uninstalled later if you wish.Restart your computer and solve the outstanding issues. -
Unable to find a way to do a full system restore
I'm trying to do a complete system restore on my computer but may not know where to look for it. Everything that I keep finding is check the restore points, I need to get my computer back to factory settings. Does anyone have any ideas on how to do that?
You do not do so by restoring the system.
Read the info below:
Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .
There is no Vista free download legal available.
Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.
Normally, they do this for a cost of $ small.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.
See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.
Normally, you have to press F10 or F11 at startup to start the recovery process...
Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.
They will tell you how to do this.
Every computer manufacturer has their own way of making recovery disk/s.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Or borrow a good Microsoft Vista DVD (not Dell, HP, Acer, recovery disk/s etc).
A good Vista DVD contains all versions of Vista.
The product key determines which version of Vista is installed.There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.
If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):
At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu
Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.
http://support.Microsoft.com/default.aspx/KB/918884
MS advice on the conduct of clean install.
http://www.theeldergeekvista.com/vista_clean_installation.htm
A tutorial on the use of a clean install
http://www.winsupersite.com/showcase/winvista_install_03.asp
Super Guide Windows Vista Installation
After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.
Save all data, because it will be lost during a clean installation.
See you soon.
Mick Murphy - Microsoft partner
-
Portege M400 system hangs after Vista system restore
My system crashed by doing a system restore. Now on startup it gives errors. When I boot from the CD, I go for the choice of the partition to install on and there is no partition, and it has this error:
No hard drive found. Click on load a driver to provide for installing mass storage driver.
I went to Toshiba and Microsoft for help. Or can direct me to the right solution. I can't find my recovery disk. I have just the windows installation disc. Is there an easy fix for this?
* original title - cannot fine partition on Portege M400 during installation of Windows Vista Business 32 bit.*
http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp
For any problem, reinstall Vista, contact the manufacturer of your laptop.
Here is the General info on reinstallation of Vista:
Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .
There is no Vista free download legal available.
Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.
Normally, they do this for a cost of $ small.
In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.
See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.
Normally, you have to press F10 or F11 at startup to start the recovery process...
Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.
Also ask them if it is possible to do the recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.
They will tell you how to do this.
Every computer manufacturer has their own way of making recovery disk/s.
Or borrow a good Microsoft Vista DVD (not Dell, HP, Acer, recovery disk/s etc).
A good Vista DVD contains all versions of Vista.
The product key determines which version of Vista is installed.There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.
If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):
Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.
At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu
http://support.Microsoft.com/default.aspx/KB/918884
MS advice on the conduct of clean install.
http://www.theeldergeekvista.com/vista_clean_installation.htm
A tutorial on the use of a clean install
http://www.winsupersite.com/showcase/winvista_install_03.asp
Super Guide Windows Vista Installation
After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.
See you soon.
Mick Murphy - Microsoft partner
-
Fails to start repair, system restore breaks down
I have Vista Home Premium. Last week he forced updates to install, and since my laptop does not start.
Notice - can be found here: http://social.answers.microsoft.com/Forums/de-CH/vistahardware/thread/73f7be44-0722-42dc-8dd4-188697f6c64a did NOT work.
I tried to start safe mode and do a system restore - fails. stop at the line "crcdsk".
The Bootable repair disk does not work - I already ran Startup Repair from the Vista preinstalled on my laptop, and he arrived at the same point.
I ran chkdsk c: f, who found mirror TF (MTF) errors and fixed them. However, he cannot access d: which is where everything is written in (I have a HD 2 part apparently).
I managed to 'pull' some of my files on a linux system, so I hope I haven't lost everything. However...
What should I do now?
I don't have a Vista CD with my laptop Sony Vaio, as it came pre-installed.
D: is normally the recovery disk to put it back to factory settings.
Check with Sony on this subject for your model.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The startup Neosmart Repairdisk is what we usually recommend. but you say you have tried a Bootable ERD without result
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Vista recovery media obtain and/or use the Partition Recovery Vista on your computer to the factory settings .
There is no Vista free download legal available.
http://eSupport.Sony.com/Perl/select-System.pl?PRODTYPE=1, 24,26,66,9,70,5,72
Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.
Normally, they do this for a cost of $ small.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.
See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.
Normally, you have to press F10 or F11 at startup to start the recovery process...
Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
A good Vista DVD contains all versions of Vista.
The product key determines which version of Vista is installed.There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.
If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):
Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.
At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu
http://support.Microsoft.com/default.aspx/KB/918884
MS advice on the conduct of clean install.
http://www.theeldergeekvista.com/vista_clean_installation.htm
A tutorial on the use of a clean install
http://www.winsupersite.com/showcase/winvista_install_03.asp
Super Guide Windows Vista Installation
After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.
Save all data, because it will be lost during a clean installation.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
http://support.Microsoft.com/default.aspx/KB/326246
'How to replace Microsoft software or hardware, order service packs and upgrades, and replace product manuals'
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
And here's a little more information of data recovery for you:
Data recovery:
1. slave of your hard drive in another computer and read/save your data out there.
2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.
3 Alternatively, use Knoppix Live CD to recover data:
http://www.Knopper.NET/Knoppix/index-en.html
Download/save the file Knoppix Live CD ISO above.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
http://isorecorder.alexfeinman.com/isorecorder.htm
Download the Vista software from the link above.
After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.
Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.
Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1st in the boot order.
Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.
When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.
Click on the icons of hard drive to open and to understand which drive is which.
Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).
Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.
See you soon.
Mick Murphy - Microsoft partner
-
Insert the active windows system restore CD
My laptop HP G7000 with the version of windows Vista Edition family gets empty with only a cursor arrow showing after trying to start.
This problem occurred when I had a power failure when running the system recovery and was able to complete it. The system keeps asking for active windows system restore CDs
I was able to assess the documents on the hard drive when connected to a system of work
Can someone help me because I do not have the requested CD
Vista Media recovery obtaining and/or using the Vista recovery on your computer Partition to factory settings .
There is no Vista free download legal available.
http://welcome.HP.com/country/us/en/contact_us.html
Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.
Normally, they do this for a cost of $ small.
In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.
See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.
Normally, you have to press F10 or F11 at startup to start the recovery process...
Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.
Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
A good Vista DVD contains all versions of Vista.
The product key determines which version of Vista is installed.There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.
If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):
Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.
At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu
http://support.Microsoft.com/default.aspx/KB/918884
MS advice on the conduct of clean install.
http://www.theeldergeekvista.com/vista_clean_installation.htm
A tutorial on the use of a clean install
http://www.winsupersite.com/showcase/winvista_install_03.asp
Super Guide Windows Vista Installation
After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.
Save all data, because it will be lost during a clean installation.
See you soon. Mick Murphy - Microsoft partner
-
I am running Vista Home Premium on a laptop Toshiba Satellite L305. I ran the system restore due to a problem of "Internet Explorer cannot display the website" (by Microsoft troubleshooting guide for this problem) and selected restore point earlier. Now the computer asks for a password that I don't remember. I tried all the possible passwords I can think. There is only a single user account on this computer. The administrator account should be disabled, it is not an option when connecting safe mode. I don't have a system repair disc set. Is it possible to run the system back restore to select a more recent restore point which does not require a password? Or y at - it another way to connect to the computer?
http://Windows.Microsoft.com/en-us/Windows-Vista/undo-system-restore
If you tried to use the system restore to solve a problem, but the problem remained or other problems were introduced, you can undo the restore operation. After you cancel the system restore, you can try using a different restore point.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
http://support.Microsoft.com/default.aspx/KB/189126
"Microsoft's strategy concerning lost or forgotten passwords"
Microsoft cannot help you recover the passwords of the files and Microsoft who are lost or forgotten product features.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Vista Media recovery obtaining and/or using the Vista recovery on your computer Partition to factory settings .
There is no Vista free download legal available.
Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.
Normally, they do this for a cost of $ small.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.
See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.
Normally, you have to press F10 or F11 at startup to start the recovery process...
Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
A good Vista DVD contains all versions of Vista.
The product key determines which version of Vista is installed.There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.
If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):
Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.
At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu
http://support.Microsoft.com/default.aspx/KB/918884
MS advice on the conduct of clean install.
http://www.theeldergeekvista.com/vista_clean_installation.htm
A tutorial on the use of a clean install
http://www.winsupersite.com/showcase/winvista_install_03.asp
Super Guide Windows Vista Installation
After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.
Mick Murphy - Microsoft partner
-
can't get back into windows after a system restore
I ran a system restore on my desktop running windows vista edition Home premium 64-bit. half way through my screan saver restoration opened and collapsed the restoration ended. After a few hours I shut down the computer. now when I start my pc it runs all preliminary functions and allows me to choose to either start windows failure, safe with fast back or normal mode. If I choose the mode safe mode (with or without back) through a loading phase where it shows everybody that it loads, it stops on a cdc.dsk file, and then processes to a black screan. If I choose load windows normally it goes to a black screan. the windows vista I have is one that came with the pc, so I don't have the disks to run. is it possible to fix this or did I just turn a pc $1500 in a very expensive papper weight?
If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:
Download the ISO on the link provided and make a record of repair time it starts.
Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.
At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.
When you have changed that, insert the Bootable disk you did in the drive and reboot.
http://www.bleepingcomputer.com/tutorials/tutorial148.html
Link above shows what the process looks like and a manual, it load the repair options.
NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.
Read all the info on the website on how to create and use it.
http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/
ISO Burner: http://www.snapfiles.com/get/active-isoburner.html
It's a very good Vista startup repair disk.
You can do a system restart tool, system, etc it restore.
It is NOT a disc of resettlement.
And the 32-bit is what normally comes on a computer, unless 64-bit.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.
There is no Vista free download legal available.
Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.
Normally, they do this for a cost of $ small.
In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.
See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.
Normally, you have to press F10 or F11 at startup to start the recovery process...
Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.
Ask them if you can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.
They will tell you how to do this.
Every computer manufacturer has their own way of making recovery disk/s.
Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
A good Vista DVD contains all versions of Vista.
The product key determines which version of Vista is installed.There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.
If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):
Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.
At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu
http://support.Microsoft.com/default.aspx/KB/918884
MS advice on the conduct of clean install.
http://www.theeldergeekvista.com/vista_clean_installation.htm
A tutorial on the use of a clean install
http://www.winsupersite.com/showcase/winvista_install_03.asp
Super Guide Windows Vista Installation
After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.
See you soon.
Mick Murphy - Microsoft partner
-
SYSTEM RESTORE! NEEED HELP! All the restore points went :(
I have an Acer Aspire 7730 running Windows Vista and I need help. An attempt to clear up space, I delete my restore points. I decided a few days later I want to restore to an earlier date; Guess who has no conservation is only 27 minutes ago! : D I need to know how to create a new set to ANY point in time restore point. Or at least when I first took it out of the box. Please help? : S
You cannot use system restore to factory settings.
And you can not create a Restore Point for yesterday today.
Restore of yesterday point had to be made, so that you could come back today.
You must use one of the methods below to return to the factory settings.
How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.
There is no Vista free download legal available.
https://secure.TX.Acer.com/rcdb/main.aspx?brand=Acer
Contact Acer at the link above and ask them to send you a set of recovery Vista disc/s.
Normally, they do this for a cost of $ small.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.
See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.
Normally, you have to press F10 or F11, and Acer is normally Alt + F10 at startup to start the recovery process...
Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Ask them if you can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.
They will tell you how to do this.
Every computer manufacturer has their own way of making recovery disk/s.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
A good Vista DVD contains all versions of Vista.
The product key determines which version of Vista is installed.There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.
If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):
Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.
At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu
http://support.Microsoft.com/default.aspx/KB/918884
MS advice on the conduct of clean install.
http://www.theeldergeekvista.com/vista_clean_installation.htm
A tutorial on the use of a clean install
http://www.winsupersite.com/showcase/winvista_install_03.asp
Super Guide Windows Vista Installation
After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.
Save all data, because it will be lost during a clean installation.
See you soon.
Mick Murphy - Microsoft partner
Maybe you are looking for
-
Final Cut Express had a Radial blur called video effect where you can adjust the angle and the steps of the blur. It seems that this version of the Radial blur area does not exist in Final Cut Pro X (10.2.2 worm Anyone know if there is a way to recre
-
Hello! I'm working to do a Subvi to define an outputs to a valve. I have tried for some time now, but don't seem to do things. This is the function I'm looking for: Output opens the valve, and the closed output. These two cannot be active at the same
-
Lost e-mail account and subfolders in Windows Live Mail.
I closed my laptop using the power button on a hurry last night, now I connected this morning my hotmail account to Windows Live Mail, Inbox, and sent Follders etc. were lost. Ridicule me. Live Mail was open at the time wherever I stop. However, I am
-
My icons and Windows Sidebar Gadgets on the desktop are suddenly very small.
The electricity went out, and when we restarted the computer (Dell) all the desktop icons and windows and my sidebar gadgets are extremely low. Can you help me to change everything back to normal size?
-
Can I change a drive partition size without erasing the data?
Original title: extend a Partition Is it possible to reconfigure the way a drive is partitioned, witout reformatting? I have a huge hard drive (.5TB) but not has not almost allocate enough space on the system disk. I want to fly maybe 20 or 30 GB s