HP Laserjet 1320: Printer hard drives

Similar Questions

• A LaserJet 1320 printer network connection

  The HP LaserJet 1320 printer lacks an Ethernet, only the 1320n, NT and nw models have that.  My question on this is can I connect the 1320 to my Ethernet system using Ethernet to USB converter unit? The 1320 has a USB input/output.connector.  If not, is it because the current software does not support the Ethernet connection, and if this is the case the software update?  In this application, I want to be able to use the printer HP 1320 of my laptop HP Pavilion DV7-1267 also connected to the Ethernet system.

  It is possible to install the HP LaserJet 1320 to an Ethernet network via a Jet Direct external print server.  Support direct Jet models can be found at the following URL:

  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?lang=en&cc=us&TaskID=115&prodSeriesId=410622&prodTypeId=18972&prodSeriesId=410622&ObjectID=c00229696

• LaserJet 1320: Print multiple copies

  Regardless of the number of copies I specify to print on my Laserjet 1320, it will only print one copy. I use Word 2010, Windows 8.1

  I suspect that the following is the case:

  • Your document is a MultiPage document (i.e. not just a single page).
  • You select that copies be printed "collected" (e.g. pages 1,2,3,..., 1, 2, 3,..., 1, 2, 3,...) rather than "not assembled" (i.e. pages 1,1,1,..., 2, 2, 2,..., 3, 3, 3,...).
  • The driver assumes that the printer can produce multiple copies of a source only copy - this is known as ing MOPY(I think it stands for "copy of the original multiple").
  • But the printer does not function MOPY - usually this is only available if the printer has a hard drive or a large RAM disk - I do not think that the LJ1320 supports one of these.

  You can confirm that the foregoing occurs by:

  • "Capture" a print job to a file (using the option "print to a file" in the print Word dialogue or sample driver
  • Then examing initially file resulting .prn (you should be able to open it in Notepad).
  • Most of the file can be unintelligible, but initially will look like:

  

  If the command SET QTY is there, this confirms that the driver think the printer will make copies.

  If so, check the settings of the device to the printer:

  

  to check whether or not the system thinks that a hard disk is installed on the printer, and Mopier mode is enabled or not.

  If the disk hard printer is set to installed, change to not installed.

  If the Mopier Mode is set to Enabled, change it to disabled.

  Then repeat the tests to see if it makes a difference.

  He should do it, although the print jobs sent to the printer will be larger (they will contain several copies).

• Only a network printer LaserJet 1320 prints

  Hello

  I have a shop.  In my office, I have a HP Laserjet 1320 PCL printer attached to my new computer running Windows 7. On my network, I also have a computer in the store that is running on Windows XP. After sorted desktop drivers to make the printer work with PCL 6 (it printed only a copy when the value of PCL5), I cannot now make the computer store impression. Is it important that computers are running a different version of Windows and the computer of the shop would have the Windows 7 driver for the printer as well as the XP driver or just one of them and if so the one who! This file the printer disk/s should be in?

  If the printer on the desktop computer port is LPT 1, should the store by using the same or does \\oshop?
  Any advice would be much appreciated!
  Thank you

  your best solution is directly connect to a computer and then share the printer from the pc

  LeftnWrite wrote:

  Hello

  I have a shop.  In my office, I have a HP Laserjet 1320 PCL printer attached to my new computer running Windows 7. On my network, I also have a computer in the store that is running on Windows XP. After sorted desktop drivers to make the printer work with PCL 6 (it printed only a copy when the value of PCL5), I cannot now make the computer store impression. Is it important that computers are running a different version of Windows and the computer of the shop would have the Windows 7 driver for the printer as well as the XP driver or just one of them and if so the one who! This file the printer disk/s should be in?

  If the printer on the desktop computer port is LPT 1, should the store by using the same or does \\oshop?
  Any advice would be much appreciated!
  Thank you

• HP LaserJet 1320 Print blank Page extra

  LaserJet 1320 shoot two sheets of paper when printing a single page. It does when you print a test page.

  Its also happens when I do the desktop remotely.

  Depending on the configuration page, the total number of pages does not include blank pages that follow each of the printed pages.

  Is there a hardware problem or configuration of printer?

  If it was the model that was network when you printed the configuration page that you would also get a Network Setup page.

  You must be connected to a network via an Ethernet cable to see the integrated Web server, if it is a model that supported it.

• HP driver unavailable site - for windows 8.1 HP Laserjet 1320 printer

  
  

  Hi Maxim

  Windows HP PCL5 universal printer driver

  8.1 for Windows (32 bit)

  FTP://ftp.HP.com/pub/softlib/UPD/HP-UPD-5.9.0.18326/UPD-PCL5-x32-5.9.0.18326.exe

  Windows 8.1 (64-bit)

  FTP://ftp.HP.com/pub/softlib/UPD/HP-UPD-5.9.0.18326/UPD-PCL5-x64-5.9.0.18326.exe

• HP LaserJet 1320 printer driver

  Can I use a HP 1320 LaserJer printer on a Dell with Windows 7 laptop? It seems that I could download the software, but the cord I have does not work with the laptop.

  J.-x., welcome to the forum.

  We have a problem dealing with other brands of laptops.  We have the features for them.  You will need to determine what type of connectors for your laptop is available and buy a cable that is compatible with the printer and the laptop.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• For HP LaserJet 1320 printer cable

  My parrot chewed my cable that connects the printer to my MacPro. Should what kind of cable I get to replace? I need one that is long enough.

  Thank you!

  Hello

  Your printer has two ports: USB and parallel. I think you are using the USB cable. Despite this, you can forget the parallel cable and use the USB cable that you can buy at any good computer store

  

  The flat end is for your computer and the other end is for printer.

  Kind regards.

• HP laserjet 1320 connected to windows 7 but cannot print on a windows xp computer

  We have 4 computers connected to a printer.  2 computers windows 7 and the other 2 are windows xp.  When I try to find the printer and connect to it it is an error code that is displayed saying "the server for the ' pcl 5' hp laserjet 1320 printer does not have the printer driver installed.".  If you want to find the right driver, click ok.  otherwise, click Cancel and contact your network administrator or the OEM for the printer driver correct"I don't know where to even try to find the right driver.  I tried uninstaling and reinstaling the drive of the printer and it still does not work.

  all I ended up doing was to move the printer to the computer xp and related windows computers seven until the printer this way, everything works and there is no need to download all the drivers.  I tried to download everything as you said, but I more was skip a step or put in the wrong place.  Thanks anyway for your help

  Zack

• LaserJet 1320: Hp printer does not not on Windows 10

  I just recently upgraded to Windows 10 and the HP LaserJet 1320 printer does not work. I went to the site and downloaded the correct driver (64-bit). The printer appears in the printer list when I go to devices and printers, but can not choose the printer when I go to print something. If I go into settings > devices in Windows, I'll see the printer listed, but I can not set the default printer, and it says "Driver is unavailable."

  Is there a better driver, or a way to fix this?

  Thank you.

  It is connected through the USB port, and of course, I tried connecting directly first, who did install a driver, but he had the same result as the download of the driver separately. I was finally able to make it work by installing a different driver, which I don't remember, but this has been resolved weeks ago.

• HP laserjet 1320: PRNTER IS NOT PRINTED AND ITS CRIMINAL IS OFF

  Hello

  I have HP laserJet 1320 printer, before its usb connector seems to be mulfunction, I replced the trainer, he began working again, but after a few days failed to print and its criminal turned off, put except when I turn on does not start immediately, will start after the switch several times.

  Any help is highly appreciated. Thank you

  No idea what you mean by criminal is off. If you have replaced the trainer, remove side trim and with the power off, reinstall all connections to the new trainer and see if it boots. If still an issue I think that the new trainer has a problem. There is an engine test button below the trainer that you can press to see if it prints a page with lines. If it is then that confirms that the trainer has a problem.

• HP LaserJet 1320 PCL 5, x 64

  Please help me. I have this old HP LaserJet 1320 printer, but can not find the driver. I have a memorystick with the driver, but this new PC I found in him. Cordially Karlo V. Andersen

  Hi Karlo,

  I suggest you to download and install the drivers for the printer from the manufacturer's website.

  Reference:

  http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdHome/?sp4ts.oid=410624&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3DswEnvOID%253D4132%257CswLang%253D%257Caction%253DlistDriver&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken

  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

• Dual Boot with windows XP Pro with 2 HARD drive, error on secondary windows install: "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check boot path and disk hardware... »

  Hi, I recently bought a new Hitachi 1 TB internal hard drive. I wanted to do a clean install on the new drive (d), be able to dual boot my computer and leave my old 300 GB disk (C :) as the primary windows installation. After physically installing the new HARD drive, I noticed that "new hardware found" and the the brand name flashed in the bottom right corner. I thought I'd see the new hard drive in my computer, but I did not. I initialized the new HARD drive with the computer management window (right click on my computer - manage) and I also formatted in NTFS (I had to change my printer hard drive letter to assign the new HARD drive with the letter D, but I've made other changes after this step). Now, I could see and use in my main windows on the C: installation. I then installed a windows new copy XP pro with the installation CD I got for my C: but on the D: (Note: I have a Dell computer (and the Dell reinstallation CD) and my current version of windows has SP3 while the installation CD is only SP2) (I also reformatted my HARD drive during the installation of windows to NTFS)

  Now when I try to start on installing the new on my D: I get "Windows did not start because of a configuration of the disk of the computer problem. Could not read the selected boot disk. Check startup disk and hardware access path. "and another line saying to refer to manuals HARD drive and windows.

  My Boot.ini file at this time was:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (0) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I looked towards the top of this help page, but for now I'm unlucky:

  http://support.Microsoft.com/kb/314477

  (The next steps I took by throwing from the Windows CD and go into the repair console)

  I tried to use the bootcfg /rebuild but the line to boot.ini for my secondary HARD drive still does not work.

  He gave me something like:

  [boot loader]
  Timeout = 5
  default = multi (0) disk (0) rdisk (0) partition (2) \WINDOWS
  [operating systems]
  "multi (0) disk (0) rdisk (0) partition (2) \WINDOWS="Microsoft Windows XP Professional "/ noexecute = optin/fastdetect
  "signature (ac516a5c) disk (0) rdisk (1) partition (1) \WINDOWS="Microsoft Windows XP Professional own "/ noexecute = optin/fastdetect

  I also tried to change the signature() to multi (0), but it did not work. (or try almost all possible permutations of disk() and rdisk() partition() 0 to 2).

  I also tried to use expand F(dvd-drive):\i386\ntkrnlmp(I_have_a_duo-core).ex_ D:\windows\system32\ntoskrnl.exe and a few other combinations, but I when I login as D:\windows simply, it fails to extend with a message like "could not develop" or C:\windows I get "restricted access".

  I have not yet tried CHKDSK/r, but since I did a clean install on a newly formatted drive... I don't think it would work.

  I've also marked the partition on the D: as active (in computer management), but it did not help me.

  I've done a first installation of windows repair, strangely, I couldn't fix this one... Still does not work...

  My default windows installation yet works very well & I see that windows has been installed on the D: but I'm ideas from how to operate the dual-boot, can someone throw me a BONE on what to do?

  Maybe try to do something with the Boot Manager (whatever it is?) Create a new partition and use it as a boot manager? I don't really want to do this, because if I made a mistake I will be unable to use my computer and dual boot should work without going through all this trouble... But I found this page: http://technet.microsoft.com/fr-fr/library/ee829686%28WS.10%29.aspx

  Could a clean install two HDD help? I hope I won't have to do...

  Someone has an idea?

  PS: I'm not such an advanced user so I need a solution step by step, thanks!

  Edit: I also noted that I can't see my new HARD drive in my BIOS... weird... SATA-0 is my old drive HARD 1 and 2 are my dvd 3-5 readers are 'off' and it doesn't seem to be anything that it is plugged in. I also have 4 bays for internal HARD disks. Now, 2 are busy.

  Edit2: I looked inside my case and enabled the good Sata in the Bios after a reboot it detected the drive correctly. Dual boot doesn't always work well... The fact that it was disable in the BIOS while I was installing the new HARD drive could change anything? Hmm...

  In case I wasn't clear enough: I had a windows XP Pro installed on my C:, bought a new hard drive and installed the same copy of windows on it (d). I think that should allow me to double boot between the two installs different. Even if for some reason I can't boot from one on my D:. Andrew, I do not understand why you so far physically disconnect the other drive, the point of the whole operation is to build a boot.ini file so that the BIOS knows that it y facilities 2 windows and you allow to choose (and not have conflicting problems between the 2 systems), someone correct me if I'm wrong? "Expand" the part of my first post made reference to one of the solutions provided by Microsoft in the first link that I have included in my previous post (but I can't seem to work).

  In addition, it is the procedure that I followed: http://www.ehow.com/how_5950826_boot-two-different-hard-drives.html

  (except I've had the first installation already done).

  Andrew "also, once a new hd is plugged on the pc & running, most of the BIOS will place (them) as 1st priority hd, set the BIOS to do this", you mean that by installing separately from windows on each unit when the other is not plugged in, I could choose what disk to start from defining their priority in the BIOS once they are all plugged back? It's too tedious (as I intend to move frequently between the 2 installs) and requires a computer to other users of the lack of computer knowledge. Unfortunately, it is not a viable option.

  EDIT: I DID IT! Hmmm... Well, I double checked in the recovery console, the path of the new HARD drive with the arc command Scan. Tried to start again with the MULTI (0) in my boot.ini and it worked... I also had my windows install CD in. Maybe that is why I could not start, windows needs the CD to complete the installation? Weird, I don't know what I did to the difficulty it... but hey, it works! Thanks for your ideas guys!

• My printer HP Laserjet 5 L has a hard drive?

  My printer HP Laserjet 5 L has a hard drive?

  According to the specifications don't there is no hard drive.

• Color Laserjet 4550 DN: Memory / Hard drive in a printer, that we need to have

  We have a printer Color Laserjet 4550 DN we need to dispose of it. We want to assure you that there is no hard drive, which must be erased or destroyed for security reasons, until we get rid of it.

  Only the hdn model came with a hard drive.  You can tell if you a looking at the back where you have run the cable to the computer or the network.  On this board there called EIO housing.  One is used for the network card and if you have a hard drive, there will be another card inserted in the slot EIO others which I do not think that you will have.  If there is another card just loosen the two screws and remove it.