HP Mini 110-1033ca won't start. Need help!

Similar Questions

• HP Pavilion p6510t won't start, need help!

  Hello, we have your desktop HP Pavilion p6510t with the following specifications:

  HP Pavilion p6510t PC

  • Genuine Windows 7 Home Premium 64-bit
  • Intel (r) CPU Pentium (r) Dual-Core E5400 (2.7 GHz, 2 MB L2, 800 MHz FSB)
  • SDRAM DDR3 800 MHz 4 GB [2 DIMMS]
  • 320 GB HDD at 7200 RPM SATA 3 Gb/s
  • Microsoft Office Starter 2010
  • No additional security software
  • Integrated graphics - Intel(r) Graphics Media Accelerator X 4500 [VGA]
  • No speakers
  • LightScribe 16 X MAX drive DVD +/-R/RW SuperMulti
  • Built-in Ethernet port, wireless
  • Audio Reader, 2 USB, 15-in-1 memory card
  • No TV Tuner
  • Integrated sound
  • HP USB keyboard and optical mouse

  We also bought this monitor to her (though I doubt it's important in this case):

  HP S1931a 18.5 "diagonal LCD screen

  The problem started about two months ago when the computer turns off without reason then that slowed down (before sleep should have started). After the computer restarts, he gave the beep codes that there was a problem with memory (1 short beep, 1 beep, long pause, repeat) long. After power back off and remove all devices and the power cable, the RAM has been removed (2 x 2 GB), checked for dust, bad seats, pins bent, etc...  The 2 RAM sticks have been resettled and the problem seems to be resolved.

  Fast forward two months (a bit more under warranty), the same problem occurs. This time, replace the RAM has not fixed the problem. Sometimes the computer should boot properly and then randomly cut regardless of what the processor was doing (idle or under load of 25% or more). In addition, beep codes would perhaps only half the time where it would not start. The output has been verified for feeding and another (proven) outlet has also been tried. No change. At this point, the computer won't be enough for any start screen at all, not even a blue screen.

  What he do to power on:

  • All powered fans (power supply, fan CPU cooler, case) and a spin at full speed.
  • Hard drive to wind up.
  • Green light on the power supply remains stable.
  • VA CD drive open and close normally.

  What is does not power upward:

  • No display at all.
  • No beep codes.
  • No blue light on the button walk / stop (top of case).
  • CPU does NOT get hot to the touch after 5 seconds to be under tension (with the fan and the heatsink removed and unplugged).
  • With two strips of RAM not removed, no beep of any kind.

  I also tried to use an old video card, I had to hang out, thinking that maybe the onboard graphics card were no longer works. The video card gets power as his fan runs, also at full speed. Still no display.

  I already bought a pair of replacement RAM sticks, exact same specifications and brand (Crucial), no difference. I tried all combinations of each stick into each slot with the original of the RAM in the first place, so I assumed it was sticks and replaced. Now that the RAM has been replaced and no beep codes, I suspect the motherboard or the CPU.

  I also tried to reset the BIOS by removing the battery for 10 + minutes and also move jumper to 2-3 1-2 during 10 seconds and replace (with power off).

  What I want to know is which component I need to replace to get this computer working before its tax season. I'd like to think it's the processor, because it remains cold to the touch after turning on. If this is the case, can someone confirm that this is a suitable replacement? (Intel Pentium E5700 Wolfdale 3.0 GHz LGA 775 65W Dual-Core processor desktop BX80571E5700) http://www.Newegg.com/product/product.aspx?item=N82E16819116381

  If it's the motherboard (I hope not), it can be replaced without having to re - install windows? I can't find an exact replacement for the H - I41 - Μatx Foxconn (Eton). HP has one of these in stock that could be shipped out?

  I know that the computer is already out of warranty (barely) and can do the work myself, but need help to determine the problem I want to throw the money to do this work right.

  Thank you in advance for your help!

  John

  Hello jkalbin, I think a bad mother rather than the processor card. Chess with the processors don't happen often at all. You should never feed a computer with radiator/fan all not attached to the processor. Just 5 seconds without the radiator/fan could easily burn a processor.

  The fact that the processor had no hot does not mean it does not work, if the motherboard does not send power to the processor.

  Motherboard failures are many times more often than the failures of processor. I had one processor to fail in more than 25 years of working with computers.

  Just some thoughts.

• HP Mini 110-3500 does not start

  HP Mini 110-3500 will not start. When I try to start I get a prompt back "BOOTMGR is missing" & «Press Ctrl + Alt + Delete to restart»

  I tried a "Factory Image Restore" and it failed with an ERROR msg '0xe0efooo3 '.

  Any help is appreciated.

  Sorry to hear that Geezer.

  You need to replace the HARD drive and reload the operating system.

  REO

• HP mini 110-3500 laptop: computer laptop HP mini 110-3500 fails to start after the SSD upgrade

  Hello
  I recently bought a ' crucial 250 gb 2.5 "SSD and 2 GB of RAM (also by crucial), to upgrade my laptop HP mini 110-3500, who has been extremely slow. But unfortunately, the laptop refused to start when turned on. What can I do? I am very worried.
  Enkay1

  You answered. That's what I thought. You have DDR3L-1600 low voltage 1.35 volts. Low voltage will operate at a higher voltage (1.5 volts), but it is not the ideal memory for older hardware. Need memory DDR3-1333 name specified for the HP laptop. You can confirm or refute my diagnosis by putting in the memory of the old and see if it boots.

  It's the part number you need:

  621567 001

  http://www.eBay.com/ITM/2GB-compat-to-621567-001-A3803335-A4100445-A4427375-/230655741975?PT=LH_DefaultDomain_0&hash=item35b4275017

  

  Is your memory has 8 black on the side blocks or just 4? You want 8. Also if you have Windows 7 Starter, you can not use 2 GB of RAM.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP Mini 110-1033CA screen inverter issue?

  My HP mini is having some problems. The display shows only half black (left side) and half of the normal screen on the right side. It is a small robust computer that survived impacts, floods and viruses. It would be convenient to just pass quietly and made level, but I so want to solve this problem. When I connect it to the TV the screen on the TV picture is perfect. Some research superficial, I found that it may be a problem with the screen converter? Is there anyone with experience with this? The inverter part that can be removed and replaced, or is it built into your display and and therefore you need to replace the screen? In any case I am ready to replace somewhere, I need to. Any help would be greatly appreciated.

  If the inverter had not then the entire screen would be very low. I hope that the problem is more likely to be the LCD.

• Remove the OS on a Mac Mini and it won't start

  I tried to restore my Mac Mini for her to be as good as new.

  First, I entered the data on the drive in recovery mode and deled, then I tried to reinstall the OS X but an "article not available now" message appeared. So I fool it wa because tha iMac was linked to my account of mothers instead of mine.

  I accidentally turned off the mac and were unable to enter the recovery mode since then.

  When I turn it on, the light and sound but screen remains completely black when you press cmd + A: I tried other commands and the scree turns pale and a folder with a question mark sign appears.

  Help, please!

  Try this key combination. You must press the keys you have to go upward, not after the sound of the gong.

  Command + Option + R

  Boot to OS X Recovery on the Internet.

• HP MINI 110 VF704AV: hp mini 110 locked a computer and need a password. Give me a system interrupted... CNU941B27G. CAN ANYONE HELP?

  MINI sat for awhile, when I tried to restart it continues to ask for CURRENT password... and once entered incorrectly, it says the password verification failure... .fatal error... system halted CNU941B27G

  Hello

  Enter: e9lov3p7xh (3rd character is a lowercase L)

  Kind regards

  DP - K

• HP mini 110-3100: network contoller driver needed

  Network contoller driver needed

  Network controller hardware ID:

  PCI\VEN_168C & DEV_002B & SUBSYS_E016105B & REV_01
  PCI\VEN_168C & DEV_002B & SUBSYS_E016105B
  PCI\VEN_168C & DEV_002B & CC_028000
  PCI\VEN_168C & DEV_002B & CC_0280

  @mini3

  Try this one.

  https://www.Atheros-drivers.com/download-driver-Nr-300-for-Atheros-AR9285-and-Windows7.html

  REO

• HP Mini 110: Password check failed: CNU9273LZJ - need to password pls

  Need password for CNU9273LZJ

  Axelin

  What password? -BIOS or Windows?

  If the BIOS admin password verification failed, then try this:

  e9lo7xfk0w

  all are lowercase letters
  third letter is small case L
  fourth letter is small case O
  is the ninth character number zero

  Concerning

  Visruth

• HP mini 110-1033CA: Bios password

  Hi can someone help me with the bios password for my HP mini, 2MC9264JNH serial number computer

  Hello

  What is the error code? Please try (all lower case):

  74eo7gvw9z

  If not try 3 times and the error message (or stop) return code.

  Concerning

• NetBook, HP Mini 210-3000ew vs Windows 8, NEED HELP

  Hello

  I have a few questions. At first sorry for my English, I know it's horrible; D.

  1. I want to install windows on my Hp Mini 210-3000ew netbook 8. For an application on this OS, I need to have the screen resolution 1024 x 768, while my normal screen resolution is 1024 x 600 (recommended by the manufacturer). I can go to regedit and change the 'Display1_DownScalingSupported' value to 1, so I'll be able to adjust my screen resolution of 1024 x 768, but I don't know if this operation won't spoil/break my screen/matrix. What are the chances that my screen/matrix can break down as a result of this operation? Or maybe after a certain period of time to aid higher than the recommended resolution that I will get a few dead pixels or something like that? Is - this windows 8 after changing the present resolution be ok? And can I install it with screen resolution 1024 x 600 or Setup will be out of reach of the screen?

  2. I've been looking for the drivers for windows Web site 8 for Hp Mini 210-3000ew, but I only found drivers for windows 7. They are compatible with windows 8? Or I do not need to install any drivers for my netbook with windows in all 8?

  I am happy for any help. Thanks to advice.

  As far as I know, Windows 7 Starter is an OEM product only and the only source is from the supplier. Microsoft doesn't have a link to download the image.

• Install the Mini PCI wireless network card. Need help!

  Hello
  I have laptop Toshiba 5200-701 which is upgradble of wireless network, so I bought the mini PCI card Philips wireless brand. The reference is PH12127-E/PH11107-E and support 802.11a/b/g network address MAC 00 4F 05 43 88 F4.
  When I inserted the card in the laptop it shows new hardware found and then I downloaded website IBM software since I was told that this card is basically designed for laptop IBM, however, my laptop is unable to install the software and still facing problem... so please could someone help.
  Thank you very much.

  Moral salvation

  Well, in my opinion, you bought a bad wireless card. I don t think that your game can works with your device. Before you buy some hardware components, you need to check the compatibility of these parts. Toshiba service partners always have information about the units on the right. However, I found a wireless card that is compatible with your laptop. It's a PA3212U-1MPC.

  Good bye

• MS Update hangs whenever he starts; need help to reset/repair (XP - SP3)

  Since a hard stop MS Update due to the loss of power, it has been send me adjustments: the process crashes when starting, either manually * or automatically, and - svchost CPU use goes through the roof.  MSE is also affected, unable to update virus defs *.

  I find that what I thought was the page MS FixIt appropriate here, but the utility stops with error code 80072F8F.  Before proceeding to the long list of fixes for the manual reset option can be found on this page, I wanted to check if (1) I'm following the correct instructions so I do not worsen things, and (2) the question whether anyone knew how to get the automatic utility to function (which, to effect a fix, would be preferable to the manual procedure).

  I'll note that I tried to bugs 'simple' as [Auto Update & BITS] reset, but nothing helped.  My guess is that there is a lock file somewhere (or similar signaling technique) confuses the utility to know where in the process it is / was stopped, but I don't know enough about how it works in order to reset it.

  Thank you all.  It has been stressing out me for the last week.

  * - For manual execution, MS Update ahead never past the research stage.
  * - For manual execution of update MSE virus def, it too would be hooking up with the message 'Search'... "appears and the bar color in about a third.

  The Windows updates November 2013 included KB2888505 cumulative update for Internet Explorer.

  http://support.Microsoft.com/kb/2888505/en-GB

  There is a known issue with this update, it can cause Windows Update work 100% of the CPU, sometimes for hours before he solves the list of updates. Some suggest downloading the update and running it manually.  Personally, I left the Windows Update process and it finally ended.

  Of course, it may not match your situation.

• the CC Office configuration won't work - need help (win7).

  Hi, I just bought cc and I launched the configuration of Office cc (windows 7 prof.). the installer crashed about 60% saying "Setup cc no longer works." It ist not logfile´or any other explanation of this error.
  I closed all programs before security I have Setup released cc.
  Note: it is an old photoshop cs2 on my pc installed and in use.
  any ideas what I can do? Thank you!

  run vacuuming for cc, use of the Adobe Creative Cloud cleaning tool to solve installation problems, restart your computer and restart the installation of the application of cc desktop.

• OBIEE starter needs help

  Dear all,
  I just installed the db OBIEE and oracle 10.2.0.3.0. (with the sachems sample) but I'm not in a position using the administrator.
  Here are the steps that I did.
  (1) install jdk
  (2) install db oracle 10.2.0.3.0
  (3) install OBIEE
  (4) download SH file containing sh.rpd and other files.
  (5) Paste sh file in "OracleBIDATA\web\catalog".
  (6) add CtatlogPath in file instanceconfig.xml 'OracleBIDATA\web\catalog\sh '.
  (7) sh.rpd copy and paste in OracleBI\Server\Repository
  (8) add entry ' Star = sh.rpd, default; "and comment on an old.
  (9) I installed it on Win 7 I was facing problem for ODB connection so I applied the patch 'p5699495_10203_WINNT12.zip '.
  (10) that I created the ODBC connection like
  Name of Data Source = sh
  The TNS Service name = ORCL
  User ID = sh
  then I test the connection, and it succeeded.
  (11) after that I restart the services.
  (12) open administrator and connect by using "Administrator" I see 'orcl SH' in the PHYSICAL LAYER.
  13 Connection Pool settings) are
  Call Interface = SPOUT 10 g / 11g
  Name of Data Source = sh (his was default ORCL)
  username = sh
  password = password custom
  then I click on the table as PRODUCTS and click view data or update the lines I got the number of errors.
  [NQODBC] [SQL_STATE: S1000] [nQSError: 10058] A general error occurred.
  [nQSError: 43093] An error occurred when processing the statement EXECUTE PHYSICS.
  [nQSError: 17001] Oracle error code: 1017, message: ORA-01017: name of user and password invalid. connection refused the call of the OIC OCILogon.
  [nQSError: 17014] Cannot connect to the Oracle database
  
  Any help?

  Hi friend

  Click the propierties of the 'Pool of connections' and enter the user and the correct password. Then, click 'OK' to close the connection pool propierties. After that, check and save the changes. When changes are saved, you must go to a column in a table on the physical layer and then click on the right button and select "Update of the number of lines".

  I hope this can help you.