HP pavilion dv6 did not start

Similar Questions

• HP Pavilion dv6 does not start. CapsLock flashes 3 times.

  Hp Pavilion dv6 , I bought about 11 months ago. When I tried to turn it on today morning, it didn't start and the light caps lock flashes 3 times. I searched the Internet and discovered that it is a memory problem. Is there a solution to this problem so that I can fix it in the House?

  Hello

  Try to remove and re-seating memory module - the procedure is detailed from Page 68 of your & Maintenance Guide.

  Failure to correct the problem, as your laptop is still under warranty, your best option is to contact HP and make arrangements for this repaired under warranty - if necessary, you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  Kind regards

  DP - K

• My HP Pavilion DV6 will not start after replacing the screen

  I just replaced a cracked screen by following the instructions in the maintenance manual and now it does not start. The power light turns on and the fan works but nothing else happens. What can I do to trouble shoot this problem?

  The most common problem is the connection of the cable to the screen.  Make sure that it is tight. Check the connection to the motherboard as well, but it's usually OK.

• Pavilion dv6 3010so not start

  My laptop does not start correctly. This happened after I had to force close is there a few days after it froze.

  When I start it, it almost goes right to the black (I am able to press ESC to switch to the Boot Menu screen). The power light is on, as well as not soun andWiF lights (F11 and F12) and the hard drive and the battery is running

  I tried a hard reset, but it does not work. I tried to connect to the TV, but I get no picture

  I tried to run a start-up test and a run to here, and the two tests failed

  When I enter the start menu and press F11 to perform a system recovery, I get a blue screen with a picture (original startup screen, maybe?), and after about 10-15 minutes, I have the option to format.

  Should I format, or even send it in for repair? I would really like to avoid this because I have files, I want to first of all access.

  So, it's official. The HARD drive has failed. It's a little depressing, but well, they are easy to replace!

• Pavilion dv6 does not start.

  I realize how close to, it is impossible to help someone fix a computer on the Internet, but I thought I should give it a shot.

  When I start the computer to the top, volume, power, wifi, the trackpad lights and numlock LEDs and fan turns on, then only the capslock light flashes. Nothing else happens. The screen remains empty and therefore does not allow me to get into the BIOS. No more noises not coming from the laptop. I am unable to do anything to change the lights on the computer. Pressing caps, numlock, winlock or the trackpad button do nothing.

  I don't know what caused the problem. The computer worked well the night before and the next morning, when I tried to turn it on, it happened. I think that the symptoms I have outlined point to a hard drive problem, and my warranty has expired. So before I crack this thing open and start playing with it, someone has it any suggestions?

  Hello

  As you're laptop is out of warranty, the best advice I can give would be to take it to a local computer repair shop and get an estimate (and to confirm the diagnosis) for the cost of repairs.  At cost less this way you can weigh-up this repair against the cost of a new laptop and then a decision.

  Kind regards

  DP - K

• Satellite M50: Windows did not start because of a corrupted system file

  Hi all.

  I have a problem with my laptop Satellite M50. When you turn on the laptop, a message appears: "Windows did not start because the following file is missing or corrupt: \windows\system32\config\system»

  I am aware of my product recovery CD-Rom and have inserted - however, I don't want to reformat my HARD drive as I have files I back (foolishly) not upward.

  Is there another method to repair the corrupted file without having to wipe all files on the HARD drive? (I don't have an XP CD - the operating system is loaded OEM when the laptop was purchased)

  Thank you very much!

  Hello

  Hmm, using the repair console could be a good way to copy or replace the damaged or missing files on the HARD drive.
  BUT you need to start the console of Windows XP CD of original Startup Repair.
  Without this CD, you will not be able to repair the operating system. The Toshiba Recovery CD contains only image files and does not start the repair console.

  Now the question is; How to back up data.
  You can remove the HARD drive and connect it to the PC second via the external USB HARD disk controller.
  Then you should be able to copy important files on the second computer.
  After backup files you can start the installation from the recovery CD.

  Good luck

• Windows Pro L10 satellite did not start successfully

  I have a satellite pro L10 at home which was working fine yesterday.
  However, I'm going to turn in today and after the toshiba screen comes up I get a message on the screen saying "We apologize for the inconvinience, but windows did not start successfully" it gives then options such as safe mode, safe mode with network, last known configuration and start windows normally.

  No matter what is selected, I get the loading windows screen but then it goes black and nothing happens.
  Is there something I can do manually which will remedy this because stupidly

  I have recent work here that has not yet been saved!
  Thanks in advance

  Hello

  In my opinion, there is nothing to do because the operating system cannot start, even in SafeMode with network, last known configuration, etc.
  You need to reinstall the operating system

  If you want to backup the data on the HARD disk, you will need to access the HARD disk
  You can create a bootable CD WinPE which help you to gain access to the HARD drive

  Download WinPE image (use google) and create the bootable CD. You will need to burn the image to CD in order to get a bootable CD.
  Can boot from this CD, backup the data on the external HARD disk and then reinstall windows

• Service pack update from 1 to 2 now, I get a "windows did not start properly.

  I needed to upgrade my addition House of windows xp service Pack 1 to service pack 2 to add Norton to my system... I did it and my system asked me to re - start to take effect. I did and now I get the black screen that says white on it that says that windows did not start successfully... and start normally or in safe mode... I tried all the options and I get a dell screen and it goes straight to the screen... HELP PLEASE!

  See...

  Help: I got hacked. Now what should I do?
       http://TechNet.Microsoft.com/en-us/library/cc700813.aspx

  Personal data backup (which none should be considered 100% reliable at this point) then format the HARD disk and do a clean install of Windows.  Please note that a repair installation (upgrade AKA on-site) won't fix this!

  HOW to do a clean install of Windows XP: see method 1 and http://michaelstevenstech.com/cleanxpinstall.html#steps in http://support.microsoft.com/kb/978307

  Once installed the clean, you will have the equivalent of a "new computer" in order to take care of everything on the next page before connecting the machine to the internet or one local network (i.e. other computers) otherwise and before using a flash drive or the SD card that is not brand new, or has not been freshly formatted:

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  Other useful references include:

  HOW to get a computer that is running Windows XP Gold (no Service Pack) fully patched (after a clean install)
  http://groups.Google.com/group/Microsoft.public.windowsupdate/MSG/3f5afa8ed33e121c

  HOW TO get a computer that is running Windows XP SP1 (a) or SP2 fully patched (after a clean install)
  http://groups.Google.com/group/Microsoft.public.WindowsXP.General/MSG/a066ae41add7dd2b

  Tip: After getting the computer fully patched, download/install KB971029 manually: http://support.microsoft.com/kb/971029

  NB: No matter what Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free and download/run the removal tool before installing updates, Windows Service Packs, or updates IE and before installing your new anti-virus application (which will require WinXP SP3 must be installed).

  Norton Removal Tool
       FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  McAfee Consumer product removal tool
       http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  See also:

  Measures to help prevent spyware
  http://www.Microsoft.com/security/spyware/prevent.aspx

  Measures to help prevent computer worms
  http://www.Microsoft.com/security/worms/prevent.aspx

  Avoid fake security software!
  http://www.Microsoft.com/security/antivirus/rogue.aspx

  If these procedures look too complex - and there is no shame in admitting this isn't your cup of tea - take the machine to a local, good reputation and stand-alone computer (that is, not BigBoxStoreUSA or Geek Squad) repair facility.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Error when you try to install Windows XP Service Pack 3: "We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this.

  Windows XP SP3 problem

  Recently, I met a problem with my PC and was forced to use the system recovery. Now I'm back to factory settings and try to install Windows XP Service Pack 3 on my computer. Windows Update won't work for me, that whenever I try to update I get [error number: 0x8024400A]. I think it's because I use Service Pack 2, or that's what I concluded after researching the problem, anyway.

  This is not my real concern, however. Because I could not get the update automatically, I tried to download and install the "Windows XP Service Pack 3 Network Installation Package for IT professionals and developers" myself. The first time I did it, I restarted the PC after the installation and was met with "We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this. "  I went into safe mode and went to a just system restore point before SP3 was installed, but now I don't know how to install it correctly without encountering this problem after reboot. I'm hardly the easy just stick with SP2 when there are potentially important available updates. How can I get Windows Service Pack 3 is installed on my PC?

  It's certainly interesting!

  If the cause of your problem is to have a HP PC with an AMD processor and an original image on your hard drive (and of course it sounds like this is the case), the solution should be to rename the file intelppm.sys and launch the sp37394.exe patch. Once done, the SP3 file that you downloaded from here:
  http://www.Microsoft.com/en-US/Download/details.aspx?ID=24
  SHOULD work!
  I'm puzzled why there is no intelppm.sys file in your directory C:\WINDOWS\system32\drivers.
  Since you recently returned to square one with your PC ("return to factory settings"), then you may as well run the patch from this page:
  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?cc=us&LC=en&DLC=en&softwareitem=PV-60484-2
  and try the SP3 Setup file again.
  But, first, let's be absolutely sure that we are both using the same terminology. Please answer the following questions:
  1. have you safely backed up ALL your data?
  2. what method did you use to ride "back to factory settings? I think that your choices have been a destructive restore (full) and a (partial) non-destructive recovery. The first erases the disk and leave you with a pristine image and NOTHING ELSE (which means that all of your programs and data get deleted). The other (which does not always correctly) is supposed to leave programs and data intact.

• HP Pavilion dv6910us does not start

  HP Pavilion dv6910us will not start. Power, bar of quickplay, touchpad and dvd lights on then just immediately stop no beep codes or fan sounds are heard. Also tried the hard reset and no luck.

  Any help much appreciated.

  Hi @jaimet1, @Sinister , @stevestock1 , @Kscarlisle , @Abdullah_Ali ,.

  Thank you all for visiting the Forums HP's Support and welcome. It's a great site for information and questions. I looked at your question about your HP Pavilion Notebook and starting problems.  If you have replaced the motherboard and it is always the case - it isn't the graphics as graphics are attached to the motherboard. Here is a link to computer will not start.  I start at the top and work my way down.

  Mine has been corrected with the relocation of the HARD drive. Others must have fixed with just reinstalling the memory. Here is a video that shows you how do to remove and reinstall the HARD drive and memory.

  Note Remove all USB devices. Disconnect all devices of non-essential, as these can cause some problems.

  You can Reset the BIOS with this document by selecting the reload the default BIOS settings. Helping others it restores the default settings.

  I hope something here helps anyone of you difficulty the laptop.

  Thank you.

• "When try to turn on my computer: Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid

  Original title: configuration of the CRA

  Hi, I got this message then try to turn on my computer:

  "Windows did not start because of the following ARC firmware boot configuration problem: the ' osload partition ' parameter setting is invalid. "Please check the Windows documentation about the configuration option BOW and your reference manuals of the equipment for more information.

  can someone help me?

  Hi sugenghariyono,

  ·         Did you do changes on the computer before the show?

  ·         What is the brand and model of the computer?

  ·         Are you able to boot to the desktop?

  Follow the steps in the article.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  For reference:

  Advanced Troubleshooting for General startup problems in Windows XP

• How can I fix "Windows did not start because of...» »

  "Windows did not start due to a problem in the disk of the computer configuration."

  I have re-installed windows XP on my laptop using my USB because the laptop doesn't have a CD player. I used "WinToFlash" which allowed me to convert my installation CD to run on my USB. But no matter what I do I can't fix it. I am very good with computers but I have never encountered this problem. I can not re - install using my USB again because I get the error, and I can't boot the PC because I get the error. When I press a key it just restarts... Any help? Please?

  If you can boot into the BIOS screen, check if the USB is given as a choice of boot.  Do as the first in the boot order.

  Also this BIOS is set by default and if not go back to the default settings (see the owner's manual I don't know what computer you have)

• Error message: Winlogon.Exe could not locate the item. This Application did not start because Comctl32.Dll was not found.

  Update of security hung up during installation. I waited 12 hours for the update complete and nothing happened. Whe I reboot XP P4 syster, I get the Message from messageError: Winlogon.Exe could not locate component. This Application did not start because Comctl32.Dll was not found.

  Re-installed SP3... Installed hard drive then... cloned old drive and new drive... After several updates, it seems to do very well. Tried several programs/operations and seems normal. One day turned but didn't have to build another system or this one back up.  Thanks for the idea.     F

• Get the following error on reboot of the computer: Windows did not start because of a configuration of the disk of the computer problem

  Original title: where can I download iso windows xp recovery CD

  I have a file.which damaged boot.ini file later, when I restart it could not start, with the message:
  Windows did not start because of a configuration of the disk of the computer problem.

  Could not read from the selected boot disk. Check the hardware path and startup disk.

  Please check the Windows documentation about the configuration of disk material and your reference manuals of the equipment for more information.
  So I need an iso file XP Recovery.
  I can simply copy the iso files on USB and start with usb?

  Hello

  1. don't you make changes on the computer before this problem?

  First I suggest you try the troubleshooting methods provided in the following article and the check if that resolves this problem.
  Error message: "Windows did not start because of a configuration of the disk of the computer problem.
  http://support.Microsoft.com/kb/314477

• Screen black-startup - Message tells me that the machine did not start successfully

  After installing the updates of a security xp on August 23, 2011 my computer starts with the windows logo then goes to a black screen.  I have to turn off the computer.  Then, it will come with the message that the machine did not start successfully and it gives me options.  I started upward with the last known settings that worked.  However when I turned off the computer again it goes back to the black screen.  Help, please.

  Hello

  First, we will start by doing a clean boot. http://support.Microsoft.com/kb/310353

  Please click on this link and follow the instructions. This will help solve the problem and what is the cause behinf the mistake of starting.

  I hope this helps. Just reply to the results.