HP Pavilion will not start the power upward

Similar Questions

• Tecra M2 - will not start, the power light is on

  Hi, I wonder if someone out there could help me with a problem?

  I was using my M2 Friday when my friend accidentally hit a very small amount of beverage on the front of my M2, I immediately got up and got a hair dryer on it.

  After leaving it an hour I tried to use and everything worked as before which was a great relief, but a day later, I used the M2 to check my e-mail address when all of a sudden went.

  The power led is on was still and so was the light that indicates I have a CD player, I tried several times and it wouldn't start, so I went again for a day and yesteday morning it seemed that it was starting up only to freeze on the Windows screen, he then returned and he has not started since.

  Could you please give me some advice on what I could do to fix this?

  Kind regards

  Russ

  Hello Russ

  Be realistic. What you can do in this situation? Not much! You can try to start the machine. See if you can get into the BIOS and if yes how long the device will remain on. If unit is running for an extended period, you can try to boot from the CD (for example with the recovery media).

  You can try to connect as another external HARD drive to another laptop and try to back up all your important data and reinstall the OS. More than that is not possible. If there is an electronic failure, it is not easy to fix on your own and support technical investigation just to see what hardware is damaged.

• A5383 S55D satellite will not start without power

  Hello!

  I have the Toshiba Satellite S55D A5383 laptop and I have a problem with the battery, I think.
  Laptop does not start without power. What is happening since last week.
  In fact, since April 2015 battery does not last as it did when I bought (may 2014).
  I have'nt registered the product and I think I'm out of warranty.

  So, what can I do to fix this?

  You'll probably just get a new battery which is what I did. Try Amazon.

• Dell XPS 2710 all-in-One will not start, the totally blank screen

  Hello. This is my first post on the forums and I hope someone can help me.

  The Dell XPS 2710 all-in-one I bought for my 10 year old 15 months ago (Yes, that means that the guarantee is expired) will not start. No no post, no beeps, nothing. Just a brief spark of light on the screen, no words, nothing. The machine gets occasional use, and there is nothing to indicate what could have caused the problem. I have not upgraded the BIOS recently, is not as if it was a bad BIOS update, or whatever it is. I tried to hit the F1, F2, F12 keys delete during startup. No results.

  The video works. I know because I can connect my laptop to the HDMI-in port and I can see the desktop of my laptop very well. So the question is NOT the video. My son uses this machine for occasional movies and homework in his room. I want to fix the computer, if I can. I am handy with computers and built several machines from the outset in the past.

  I believe that the most likely scenario is that the motherboard has went wrong; There are several posts around the internet about motherboards 2710 AIO being unreliable. I saw an ad on the forums of Dell from a guy who said Dell Tech Support replaced its motherboard 2710 five times. I see that some of these motherboards are selling on eBay for around $200. I'm toying with the idea of getting a. I watched the service manual for the 2710 and I'm pretty confident that I could replace the Board of Directors.

  Someone had experience with permutation on their motherboard on a 2710 AIO? Or someone has any ideas on what could be the problem with my son's computer? I appreciate all the advice/help anyone could offer.

  OK, I have removed all the RAM from the motherboard (there were two sticks) and unplug the connector on the SATA hard drive. Then I turned on the machine and got two beeps very strong, but still no video on the screen indicating any form of activity of the POST. The sound signals have been first sounds I've ever heard during the procedure of boot on this machine. I put the RAM back in and re-connected the SATA cable. The way he has been, no video, no post, no beeps. I'm a bit at a loss for what I've decided, this means that the motherboard works technically and that another device on the machine is at the origin of the problem? Have I reason to assume that if I hear two beeps, then I should have the certainty that the motherboard was bad? Given that this a sound signal, the solution becomes cloudy, I guess. I can't help but feel that somehow the BIOS on the computer is damaged. Don't quite know how that could happen, however, because I have not updated the BIOS in over a year. I don't remember what BIOS version I have, but he had been working well for a year with no problems. Thanks for any other help/suggestions you can provide.

• 18 XPS does not start, the power light will not stop flashing

  I was upgrade this computer to Windows 10, I did install one instead, but the children had spyware which even then showing upwards. I did a refresh, there no I did an installation and finally got in windows. Some updates installed and restarted.

  The computer was bricked since. The only thing that happens is the LED which indicates the power above, the button will not stop flashing white light. Connected or not connected, after having held down the power button for 5, 10 and 30 seconds, the led stops flashing for a while and then again. I tried several points of sale. No idea if it is a coincidental breakdown.

  I'll change that.  I went back in and re-removed the cable from the battery.  I also removed the CMOS battery cable this time... I was at least an error message on the screen and access to the BIOS!

• HP Pavilion will not start past blue hp invent screen

  My computer does not boot past the blue hp
  Invent the screen. I took the sides off the computer. I started and I realized what was the noise that I heard and whence he came. It's the hard drive makes a noise like a fan starting then a rattling noise. Then it stop trying to load and is repeated several times, then closes. I unplugged the power supply for the drive hard drive now it
  take care when I unplug it but I can't do anything without hard drive.

  Your hard drive has failed. If you are still in warranty, contact HP to send a new hard drive. If you are out of warranty, it will be much cheaper to buy a retail hard drive to replace the original. Hope you have a value recovery disk?

• P50B satellite will not start (no power on)

  I have a TOSHIBA Satellite P50-B-103 with windows 8.1. I stop the machine yesterday, but today does not when I push the power button, nothing happens. I try to hold the power button / stop 30 seconds, but nothing happened.

  The" "DC IN / battery indicator" led is white, when I plug in or unplug the charger without changing the status led is allways white (not flashing).
  Given that I stop the machine yesterdy the "DC IN / battery indicator" is white. But I think that when I shut the machine down allways will be tour?

  That's happened?
  what needs to be done?

  Same model, same problem! It seems to start, the fan works, but 5 seconds later it stop... Still no answers on this problem of toshiba?

• Tecra M2 does not start - the power light AC blinking orange

  Someone at - it a list of codes for the Tecra M2 flash.
  My friend has a laptop that does not start at the top. the AC power LED flashes orange. a long, short, long, short, long, short, long, short.

  I checked the battery and reinstall the RAM.
  Any IDE?

  Hello

  I agree with go.
  The ASP would be able to tell what means error.

  Usually means short and 1 long: 0
  So the error must be: 1010 1010
  Due to the last significant bit (LSB), to be read by behind:
  So it now means: * 0101 0101 binary *-> it must be converted to hexadecimal-> * 55 Hex *.

  Then, you will get a hex code.
  But unfortunately, I m not very well which could mean this code

  So ask ASP for help!

• HP Pavilion will not start

  I have a Pavilion P6774Y desktop computer.  A few days ago, he would not wake up.  I turn it off and be restarted using the power switch and the blue HP screen appeared, followed by a black screen with a cursor blinking in the upper left corner who disappered after a few seconds.   After repeating this a couple of times, I swapped the monitors and HRT has not set.  Then I unplugged it, let it sit for a few minutes, plugeed it it and restarted and it started normally.    Since then, the same question has occurred several times.   Sometimes it reboots normally, other times, I get the black screen.  Sometimes it takes to unplug and reboot several times for it to start.  Does anyone have any suggestions where to look for a solution?

  TF1965, welcome to the forum.

  There are two possibilities: 1) a lack of power supply unit (PSU) or 2) a hard drive failed.

  Here's a guide to troubleshooting of the PSU.  You can test the hard drive by using the Test SMART in BIOS.

  Please click on the Thumbs up button '+' if I helped you and click on "Accept as Solution" If your problem is resolved.

• Satellite A200 - will not start with power supply connected

  My lapop is 2 years old. Whist trying to boot it restarts at least 2 times and I am running Windows 7.

  My old battery lasts about 20 minutes so I bought a new and the first time that I loaded up it gave me an hour of a time value of battery, but on the second cooldown it has provided for 20 minutes.

  It does not always to the top while the power is connected do you think that my motherboard is defective =.

  Hello

  Normally, if you connect the laptop AC adapter shouldn't t stop. Everything should work correctly as the system even starts the battery would be defective.

  So, I think you already wrote that the motherboard is faulty. In this case I recommend to contact an authorized service provider. Technicians can order a new mainboard and Exchange! :)

• SatelliteU300 will not start with power connected and fully charged battery

  I just bought a U300-13U. It works fine when charging the battery and AC is connected. However, if left to recharge completely it does not start with connected AC. Unpluging the power or remove the battery and running on AC make it work very well. Is a 'feature' to stop an overload or overheating of the battery, or just a problem with this machine. I want to run with AC and battery than both connected all the time like I did with all my other laptops.

  Any help appreciated.

  Hello Andy

  Of my friends has this small U300 and everything works well. I got it a few weeks ago to test the family Windows XP Setup and it works perfectly.

  Please test again very carefully and if the same thing happen again once I recommend you contact the Service partner in your country. They check your laptop. I have to be honest and say that describes the problem of strange sounds to me and please, don't wait too long. Contact the service as soon as possible.

  Bye and good luck!

• HP Pavilion will not start, has horizontal lines on monitor - HP Pavilion Elite M9280a

  I tried to start my computer yesterday and I had a brief message 'Error in Vista' then - my computer would not respond.

  The monitor has just shown the colored horizonal lines.  Then, I rebooted the computer.

  Since then, I can't reboot my computer at all however, I can get into safe mode to connect but remain - lines horizinal who won't go away.  The icons are much larger in safe mode too.

  When I try to log in normally, the system will repair mode and finally displays the following message:

  ' Start can't fix computer automatically "I went to see the details of the problem and this will display:

  Signature of the problem

  The Startup Repair V2 problem event name

  Problem signature 01 Auto failover

  02 6.6.6000.16396.6.0.5001.18000

  6 03

  04 131074

  05 no cause root

  06 no cause root

  07 0

  2 08

  WRP 09 repair

  2 of 10

  6.06.000.0.00.256.1 OS version

  Locale 1033 ID

  I did start diagnostic tests and everything seems ok, but the computer doesn't not recogise my graphics video card.  The system, it shows the video card - VGA video controller - PCI Bus 2 - device 0, function 0.

  Can someone help me please!  Products listed below

  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/KB/docDisplay?javax.portlet.begCache...

  Hello

  Technical page in your PC Watch: the Nvidia GeForce 8600 GT, or integrated graphics. You can check which graphic solution you have?

  You can see the desktop when it is in safe mode?

  Try the safe mode with networking enabled.

  A position that interests you, your Version of the OS (6.06.000.0.00.256.1) indicates you are running the original version of Vista. You must also upgrade Vista to Service Pack 2 (6.0.6002).

  If you can not download the drivers in safe mode with network, can you download the driver on another PC and save to disk?

  While in safe mode try to remove the possible corrupt driver using Control Panel, restart and see if Vista will load a generic graphics driver. Then, you should be able to download and install the appropriate driver.

  Jaco

• I have a aspire 5517 who will not, start seeing power turns on but nothing else happens.

  I have a aspire 5517 that won't initialize power light turns on, but nothing happens.  I tried to connect an external monitor, but it still doesn't work.  All my stuff is on this computer and I need to save at least. Help!

  Hello..

  You can try to remove the battery, then connect only the power adapter ON the computer and check if you are able to start the computer.

  In order to return the data take the hard drive on the computer startup and slave with another computer and you will be able to transfer the files from the hard drive of your computer to another.

• HP Pavilion will not start. Password Startup requirements.

  I have a ho27c model 23 H P Pavilion all-in-one number.  After an altercation with a crook of phishing, I can't get starts the request a password at startup.  After several tries, I get nothing, but demand repeated password.  I never opened a session as an administrator and has never seen it before.  Can anyone help?

  Product number is: F3D92AA #ABA and the model is: 23 h 027 c

  Thank you...

  ... LWMc

  It is always helpful if you specify the operating system installed.

  You have two options.

  Download a stand-alone antivirus\malware\adware scanner of a real antivirus company.

  Search for your game of recovery disks and perform a factory image recovery.  You can also do this from the power on with a F11 key. You is probably the best option.

  Once you got make sure that your PC and install a highly rated internet protection suite. Freebie antivirus programs are no help when it comes to rogue virus and malware such as you seem to have picked up. I prefer ESET Smart Suite and Norton Internet protection.

• computer will not start the service, access denied

  I installed this windows service: http://code.msdn.microsoft.com/windowsdesktop/CppWindowsService-cacf4948

  and when I try to start the service in the GCS I get the error 5 error message: access denied
  my account is set to admin and I even tried to use the default admin user, but still it will not work

  Hello

  From the description above, you get the error code 5 access denied cannot start the service.

  Method 1: I suggest you perform the clean boot and check if the problem persists.

  How to perform a clean boot for a problem in Windows Vista, Windows 7 or Windows 8
  http://support.Microsoft.com/kb/929135

  Note: Follow How to reset the computer to start as usual after a clean boot troubleshooting article KB929135 to reset the computer in normal mode.

  Method 2: I suggest you to scan SFC. Scan SFC will be scans all protected system files and replaces incorrect versions with appropriate Microsoft versions.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

  Post us the results once you try the steps above.