HP ProtectSmart doesn't work if connect you a HARD drive in the Bay of DVD?

Similar Questions

• Windows detected new hardware wizard appears each time I try to connect an external hard drive via the USB port.

  Whenever I try to connect an external hard drive into a USB port, Windows detected new hardware wizard will appear. He then not recognize the external drive at all. It does not appear in disk management. In Device Manager, it is listed as a 'device' USB bus controllers not. Under "other devices", there the question mark yellow and says the device is not configured correctly (code 1). External hard drive works fine on other PCs. It's a plug-and-play device. Port and USB cable work fine with other devices. Just this external hard drive has never worked on this PC.

  Hello

  I suggest that you try to remove USB controllers to the clean boot state and control.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you have finished troubleshooting, proceed as explained in the article to reset the computer to start as usual.
  See also:
  http://support.Microsoft.com/kb/310575

• What is the activation process of win7 if you change hard drive in the desktop

  I want to change my drive hard in my office to tell me the activation process of my win7 software(O/S) present in the new hard drive replaced

  If you use a 'disk cloning' software, you should not do an activation.  Disk cloning software, like Acronis True Image, copy your installed Windows 7 from one disk to another.  Several disk hard manufacturer providing this type of 'free' software on their web site(s.)

• Connection and external hard drive for the wrt610n?

  How can I do.  can't stop to understand.  When I go to the page under its storage routers, but do I need to do, to make it work.

  I don't know what I did differently than before, but now his job.

• How do clone you a hard drive on a P6770T

  Background: I have a P6770T Office, number of product XX204AV #ABA, OS: Windows 7 Home 64 bit service pack 1.

  Partitions: C: 685 GB D: 12.7 GB (recovery), Q: 0GO (MS Office 2010 protected).

  Question: I would like to add a second hard drive to the PC as a clone.   First of all, a second internal hard drive can be added (is there a location for the drive and a SATA cable port)?    Second, how do clone you a hard drive with the three partitions, as described above?    I need instructions for cooking book style because I'm a newbee.      Thank you.

  It is usually best to make a clone with an external drive. It makes no sense given the power (spinning). Seagate and WD offer similar programs, called 'DiskWizard '.

  What you'll need:

  (1) software cloning (I'll link Seagate) download the utility and download from this page user's Guide.

  (2) buy a 1 t Seagate drive (like your hard drive is a nominal 750Go).

  more than you will need:

  (3) Sata Drive enclosure includes ESata rail.

• Why the rejection of multiple photos doesn't work anymore when you change pictures?

  Why the rejection of multiple photos doesn't work anymore when you change pictures? Does anyone else have this problem? It works on my other Mac but just stop working on my computer laptop pro, I have the latest OS and it worked until a few weeks ago. Thanks for any help!

  Selection of several photos at once enter "9" to reject all still works them for me in Aperture 3.6 on El Capitan.

  Have you tested, if the problem occurs only in an Aperture library or libraries opening?

  Create a new Aperture library to test and see rejection, so it works.

  If it does not work in a new library either, I got trash Aperture preferences.

  In preferences file is now in the container folder in the user's library.

  Try this:

  • Leave the opening runs.
  • Then open your user library and delete the folder complete ~/Library/Containers/com.apple.Aperture/
  • and the ~/Library/Preferences/com.apple.Aperture.plist file

  Your user library can still be hidden. To reveal the hidden user library:

  • Bring the Finder to the front by clicking on the desktop or the Finder icon in the Dock.
  • Select your folder user/home (with the House icon in the side bar of the Finder)
  • With this window in the Finder in the front window, press the ⌘J key combination to bring up the display options.
  • In the view options panel allow you to "show the library folder. That will make your visible user library folder in your folder.
  • Open your folder, then the library folder, then the containers.
  • Move the entire folder ~/Library/Containers/com.apple.Aperture on your desktop. Move the entire folder, not just the content.
  • Delete ~/Library/Preferences/com.apple.Aperture.plist as well.

  Now, restart the Mac, start Aperture and try see your book.  If all goes well, delete the folder on the desktop.

  Re: Viewer has been reduced mode Photobook

• XP hangs after connecting an external hard drive via USB port

  When I connect an external hard drive of 250GB via a USB port on my system XP - SP3, the computer crashes immediately after the sound signal from the recognition of a normal connection PnP. There is no assignment of the station. I don't know that he had worked as can be expected before. A new 500 GB external hard drive is recognized as new hardware, the driver installed and ready to use, but after that, the PC shuts down completely new. However, when I do a system startup after connection of the same two drives, everything looks OK. Also, no problem with a USB stick of 2 GB. How to find what's the problem?

  Well - it's Windows for you, sometimes. :/

  Good luck with your new installation!

• Impossible to connect an external hard drive

  I unplugged my hard drive of the computer and re plugged. I can feel and hear it runs that power is connected but there is no light on and the computer keeps telling me that it is unplugged. I have checked and re checked all connections. If the wire to the computer could be broken and if so what call? He isn't a regular usb cord. There is a wide connector at both ends.

  Original title: ex hard drive does not work

  Hello Ellen,.

  I understand that you have a problem when connecting your external hard drive to your computer. This could be a hardware or to issue drivers. It is also possible that your cable is defective. You can try to reconnect the hard drive to another USB port. If you use an external hard drive or a hard drive internal SATA cable /IDE cable.

  Please, try the following and see if it helps.

  Method 1:

  Run the hardware troubleshooter and check the issue.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2:

  Run the fixit available at the following link.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/

  I hope this information helps.

  Please let us know if you need more help.

  Thanks and greetings
  Sarandeep S - Microsoft technical support.

• Unable to connect the external hard drive on the computer of Windows 8

  Hi I have a laptop Windows 8, I don't know too plug I bought last year I recently bought a samsung 3 TB external hard drive I plugged it in and it was recognized tried to transfer files (photos and music) he transferred a little then kept showing error e/s even when I clicked ignore it just kept showing for the next photo , so I unplugged and ive not touched since ive then connected again today to have another shot at it but it does not even appear in the my computer part now ive red somewhere else on this site to go into Device Manager and I can see the mass with a yellow triangle storage device small as he said he could on the subject , I was reading I uninstalled and plugged the hard drive on and when I plug it then settling again, nothing appears when I go back into Device Manager it is there once again with the yellow triangle, thanks in advance if anyone can give me advice.

  Thanks for the reply.

  Have you tried to uninstall and reinstall the USB controller drivers?

  If so, have you installed latest drivers from the motherboard chipset?

  Follow the steps below and check if it works:

  1 download the drivers for external hard drive from the following link and check.

  http://www.Samsung.com/us/support/downloads

  2. click on the link to the HP Web site below to download the latest drivers. Search for drivers related to USB / external peripheral.

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?cc=us&LC=en&DLC=en&product=5078476

  Click scan now.

  
  3. If you have a third party security/firewall software installed, you need to change settings or disable it temporarily.
   
  NOTE: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software / update, you must reactivate as soon as you are finished. If you are connected to the
  Internet or network so that your antivirus software is disabled, your computer is vulnerable to attacks.
   
  I hope this helps. Back to us for assistance.

• How can I get all the files from the hard drive in the non-working Compaq Presario CQ62-411NR

  Ice tea seep keyboard laptop, and after drying it feeds on. If I try a hard reboot, it is stated that I would lose all the info in the memory and I can't afford to lose my mother pictures that are on the hard drive. Is it possible to get the hard drive to work in some other way so that I can get my photos and other files.

  You can remove the hard drive and put it in a USB Enclosure.Plug USB port, another machine, where you should be able to go through it and copy your photos off on the hard drive of the host computer.

  Example:

  http://www.TigerDirect.com/applications/SearchTools/item-details.asp?EdpNo=3743052 & catid = 2783

• How to connect two external HARD drive satellite and the same printer?

  Hello

  I have now two laptop Toshiba Equium.
  What is the best way to connect them so that they can access the same external hard drive and the same printer?

  Thank you

  Hello

  I guess the two laptops are in the same network; Home LAN or WLan. Right?
  I this case I recommend you connect HARD drive and printer to one of the portable satellite.

  Then you can share the HARD drive and the printer with other cell phones on the LAN.

  You could add the network permission to others, and in this case the other participants of the network would be able to share the printer and HARD drive.

• You can plug an external hard drive to the iPad Pro?

  can plug you an external hard drive to the iPad Pro, I store all my technical documents on one and what you need to know if there is a way to connect to the iPad

  You can't plug an external hard drive on an iPad of any type.

  There are external hard drives that can create their own wifi network

  to which you can connect to your iPad. Your favorite search engine should

  provide more details.

• I see an activation which invites when I enter my product key says that's an upgrade install not the device, this worked fine on my old hard drive.

  Prompt for activation!

  Changed the hd on my pc and upgrade to ultimate version so I had to install xp first.  Now, I see an activation which invites when I get home my says product key is for upgrade not clean installation, it worked well on my old hard drive, there is no option in the wizard product activation phone how to turn it on

  Update install requires that the eligible previous operating system is installed and activated until the key is working.

  Yu seem to have correctly installed the OS upgrade - and it will never work without assistance.

  If - and only if - you have a valid COA sticker on your computer, you can try either by calling the line Activation, as suggested by Riz_Ford, or you can also try the method of double-install from here...

  http://www.winsupersite.com/article/Windows-7/clean-install-Windows-7-with-upgrade-media

  Note that the same procedure applies for WIn 7 for Vista.

• Windows 7 stop working, cannot deploy and manage hard drive

  Hello please help me

  I got 4 partitions, 3 primaries, and I had 3 installed win7

  Once one of them thought does not work

  OK I say, I deploy

  but to start the dvd he says: I can't deploy because the disks are logically...

  I remember when 4 days ago, I made these, I could hard disk partitioning and put them in the primary...

  now I can't use these functions, I can't delete the partitions, I can format it, nothing to deploy dvd... How is it possible?

  When I put the other hard drive in the same machine event... I can't change partitions from dvd deployment RFP

  If you have created parties exceeding the authorized victory under primary number were leaving you would have receieved a warning that all partitions is converted to dynamic, all partition tools/recovery of PC manufacturers would then no longer work

  You need to boot from your recovery disk, delete all partitions are then continue installing, programs or data is destroyed in the process

• Windows 7 and bios sees not the hard drive, but when I connect the hard drive to the USB with an adapter, I see directories and files

  Please, I need pc

  Original title: windows 7 and bios does not see the hard drive. but when I connect the hard drive to the USB with an adapter, I see directories and files... Ive a hp Pavilion, what to do?

  Check the BIOS for hard drive setting.

  Make sure that you do not connect the drive to a SATA/RAID port.

  Old IDE drives - check the jumper on the drive (use "Cable Select" as a starting point), the BIOS must also be set in legacy/compatibility/IDE mode. Note: If you currently use the AHCI mode, then switch to IDE mode may cause Windows to boot.

  J W Stuart: http://www.pagestart.com