I am not able to connect on one of my computers, my network error message saying: unknown username or bad password.

Similar Questions

• I can print Microsoft Word and Excel documents, but I am not able to print from the web. I get an error message that says: "Activation - Code 20' - error"Printer Not Activated".

  Activate printer F4580

  I run Microsoft Vista.  I have a printer HP F4580.  I can print Microsoft Word and Excel documents, but I am not able to print from the web.  I get an error message that says: "Activation - Code 20' - error"Printer Not Activated".  What should I do to correct this?

  Hello

  ·          What browser do you use to connect to the Internet?

  The error may occur if the wrong printer is set as default, the printer driver printer is missing, or if there are conflicts in Device Manager.

  Step 1: Make sure that the desired printer is set as the default printer:

  http://Windows.Microsoft.com/en-us/Windows7/change-your-default-printer

• Connection failure: unknown username or bad password

  I use Thunderbird without problem for businesses for nearly eight years. I currently run at the top of a tower with Windows 7 Pro. There is only a single account/e-mail address on Thunderbird.

  This morning when I went to check my e-mail I have my password is requested, then received the error 'sending of password did not. Mail server exchange.company.com replied: connection failure: unknown username or bad password. "I retried the password, restart Thunderbird and tried again, but still not received the same error. I sent an email from Thunderbird test which was very good. I am also able to connect to the server via web browser and I am able to send and receive emails on my mobile device.

  I erased all the saved passwords of Thunderbird and I checked account settings, but I am still unable to download any email Thunderbird.

  Apart from the deletion of the account, I don't really know what to do here. Any help would be appreciated! Thank you.

  The problem has been resolved. Apparently the POP stack had to be reset by the side of the Exchange.

  I hope this helps someone in the future...

• ERROR: Connection failure: unknown username or bad password

  Whenever I want too run a .exe field or a program that requires administrative permissions, I type my password using the account control user, but instead of just let me through it come up with this error:

  Connection failure: unknown username or bad password.

  I searched for fixes, but have not found one that works.

  This was a very big problem I am a player computer and all the games I have, have the administrative sign (shield) and or are .exe files.

  This has happened for about 3 or 4 months now... It really gets me upset. Since there is no way to shut off User Account Control (UAC) without opening UAC itself...

  I'm running on a:

  Manufacturer: Acer
  Model: Aspire M1201
  : Processor Dual-Core AMD (tm) 8550 2.20 GHz
  Memory (RAM live): 3.00 GB
  System type: 32-bit operating system

  http://www.Petri.co.il/disable_uac_in_windows_vista.htm

  Read method 1.

  See you soon.

  Mick Murphy - Microsoft partner

• I have an error message "connection failed: unknown username or bad password" when I try to sign int to the administrator account.

  Original title: log on failure

  Whenever I get the administrative password to say update Java, of he always says "connection failed: unknown username or bad password". I know with more certainty that the password is correct. Any help here?

  Sorry if this wrong topic.
  Thank you!

  My account is a regular account. An admin account is active.

  Having only one administrator account puts you in a precarious position because it leaves you with no alternative in case something goes wrong with this unique account. What happens when you try these options:

  • Keep her tapping F8 during startup, and then start safe mode.
  • Keep her tapping F8 during startup, and then start in Repair Mode.

  Can you log in under the admin account in one or two of these cases?

  For how long have you had this problem?

• Windows 7 professional - connection failure: unknown username or bad password.

  I have new xps computers 8700 identical Dell running windows 7 Professional.  The new dells replace the old dell dimension computers Windows XP Edition Professional.  I traced a drive 'f:' of network easily to my server from windows 2000 of the first Windows 7 Professional machine.  But when I tried to map the "f:" network drive on my windows 2000 Professional 2nd new windows machine Server 7 I got the following message: "connection failure: unknown username or bad password."  The computers are identical.  After the introduction of the first professional machine of windows 7 with success and mapping the drive "f:" on my server, I cloned the drive hard so that all my apps and settings would be the same on the second Professional machine of windows 7.   I tried to change the 2nd windows 7 professional name of the computer, but I still regularly get the "connection failure: unknown username or bad password."  Any ideas or suggestions would be greatly appreciated.

  Thanks in advance,

  Ken Preston

  Hello Ken,

  Thanks for posting your question on the forum of the Microsoft community.

  The issue you mentioned will be better suited for the public of professionals on the TechNet forums.

  I would recommend posting your query in the TechNet Forums.
   
  TechNet Forum
  http://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

  Thank you

• Unable to connect to a Samba file server. error "the connection failure: unknown username or bad password?"

  Original title: I can't connect to a server to Samba from Windows 7 files

  I used to use a Mac machine to connect to a file server Samba as smb://myfileserver.mycompany. Now I use a PC with Windows 7 Professional and when I write the address on Explorer as \\myfileserver.mycompany it opens a pop-up to enter my credentials, but when I put my authentication information and click ok, it reminds me the pop-up to try again with a message stating "connection failure: unknown username or bad password.'. '.

  I tried several times but still the same result.

  Is there another way to do this?

  Is there a third party app that will do this job?

  Thank you.

  Hello

  (1) is the computer connected to the domain?

  (2) is the issue specific to your username and password?

  (3) tried to connect from different computer?

  If the problem is specific to your username and password please contact the it Department for assistance.

• I can't connect to the other user account... error message read s 'user name' or password. We have not set up a password and user name is correct.

  I can not access another user account.  It to request a username and password.  I enter the user name is correct and there is no password.  The login page, used to have two icons of the user; but for some reason, the last log on the user icon is here and a new white icon for the new user.

  Once a week a few posters noted a problem similar to yours. In this case, I post the answer you see below. The little that I find very irritating that in each case, without exception, the poster was not able to return and account for the results, either because they found my recipe too difficult to follow, or because he or she lost interest, he or she could not be bothered to post a few comments for the benefit of other people with the same problem. There it is again...

  I do not know why you can not change this password, but maybe this method will shed light on the question:

  1. Safe boot mode.
  2. Click Start.
  3. Type the three letters cmd into the search box.
  4. Press Ctrl + Shift + Enter
  5. Click on "Run as Administrator".
  6. Type the following commands and press ENTER after each one:
     'John Doe' ppp NET user / add
     (to create an account called "John Doe" with the ppp password)
     net localgroup administrators/add "John Doe"
     (to promote "John Doe" to the Administrators group)
     net localgroup administrators/del 'John Doe'
     (to demote this account)
     NET user "John Doe" ppp
     (to set the password for John Doe at ppp)
     NET user "John Doe" / active: Yes
     (to activate this account)
     NET user "John Doe" / active: No.
     (to disable this account)
     NET user "John Doe" / del
     (do not delete this account)
     NET user
     (to view all existing account names)

• connection failure: unknown username or bad password. Windows 7 computer tries to connect to Vista

  I bought a PC W7 and tries to connect to other computers on the network. I can connect to one, cannot connect to the other, but see them as well in the network and sharing Center/view network computers and devices. When I try to log into the device poor, the system automatically changes the ID of the user - I'm on ADMIN, try to connect to GUEST - it varies from my sign in COMMENTS to ADMIN_PC\GUEST.

  I connect to the local network of the W7 machine wireless. Vista machine I can connect is connected via the ethernet connection to the router. The machine, I can see, but cannot connect to is connected to a switch via ethernet and then connected by ethernet to the router.

  After reading discussion forums, it seems that this problem could be resolved through amendments to the local security policy - network security: LAN Manager authentication level, but I can't find where to do this.

  I'm at the end of my thether - I believed the hype and thought that W7 would be easy to use. What should I do to get this thing to work?

  You don't need to change anything with LAN Manager. The problem is probably related to point C below. Here are the steps of general network troubleshooting. Just cannot apply to your situation, so just take the bits that are. It may seem daunting, but if you follow the steps in the links and suggestions below calmly and consistently, you will have no difficulty to implement your sharing.

  Problems sharing files between computers on a network are usually caused by 1) a misconfigured firewall or a firewall neglected (including a dynamic firewall in a virtual private network); or (2) inadvertently run two firewalls such as the firewall of Windows and a third-party firewall. and/or (3) do not have accounts to the same users and passwords on all computers in the workgroup. (4) tries to create actions where the operating system does not.

  In Windows 7, go to control panel > everything in Control Panel > network and sharing Center. Click on "change the advanced sharing settings. You don't want to use the residential group unless you have all Windows 7 machines. If you do and you want to use the homegroup, see Windows 7 Help & Support. Otherwise, in sharing advanced:

  Discovery of plug in the network
  Open the files and printers sharing
  Turn on the sharing section Public folder sharing
  Plug the password protected sharing

  A. configure the firewall on all machines to allow traffic to local area network (LAN) as being approved. With the Windows Firewall, turning on window file sharing and printer as the above will take care of that for you. In XP, you can run the Network Setup Wizard or just enable file sharing / print in the Windows XP firewall exceptions. If you are not running a third-party firewall or you have an antivirus/security with its own firewall component program, then you're fine.  With a third-party firewall, I usually set up the allocation of LAN with an IP address range. E.g. would be 192.168.1.0 - 192.168.1.254. Obviously you would substitute your correct subnet. Refer to the safety of any third party program or the user forums for how to correctly configure its firewall. Do not run more than one firewall. DON'T STOP FIREWALLS; CONFIGURE THEM CORRECTLY.

  (B) to facilitate the Organization, put all computers in the same workgroup. This is done from the System applet in Control Panel, the computer name tab.

  C. create the counterpart of the user accounts and passwords on all machines. You do not need to be logged into the same account on all machines and assigned to each user account passwords can be different; accounts/passwords just need to exist and to match on all machines. DO NOT NEGLECT TO CREATE PASSWORDS, EVEN IF ONLY OF SIMPLE. If you want a machine to boot directly to the desktop (a particular user account) for convenience, you can do this:

  Start > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).

  XP - set up Windows to automatically connect (MVP Ramesh) - http://windowsxp.mvps.org/Autologon.htm

  D. Si one or more of the computers on your network are XP Pro or Media Center, turn off Simple file sharing (Folder Options > view tab).

  E. create share as you wish. In Windows 7 I usually share the Desktop of the user and the Public directory.
  MS - MVP - Elephant Boy computers - don't panic!

• SE error message "connection failure: unknown username or bad password when printer sharing between Windows XP and Windows 7.

  Original title: windows 7

  Hello world
  I have a network of working group, I install a printer on the computer with xp operating system printer and shire of thise. So I have computer with os 7 (windowse 7)
  When I refill jone printer that computer (windows 7), he wants the username and password but notconnected.
  error: user name of faielur:unkown or mauvaismotdepasse connection
  pleeeeeeeeeeeeeeeeeese help me

  Hello majidyazdani,

  According to the description provided, it seems that you are having problems with the printer. As I understand it, you need to share the printer from Windows XP to Windows 7

  I need to ask you some questions to help you better.

  Click on the link below to set the printer share.

  Networking of computers running different versions of Windows

  Answer to us if you are having problems with printer sharing or any other problem of Windows, and I'd be happy to help you.

  Good day!

  Hope this information helps.

• Creating cloud - not able to connect. indicates signed out

  I am not able to connect to my creative cloud my mobile application. I enter my user ID and password, then select login. After a few seconds, I get the answer that I disconnected.  I then go to Adobe site via the browser and enter my ID and password. Everything is accepted without problem.  I'll be back to creative cloud for another attempt and get the same answer - I "Sign Out".  Someone else to make this issue?

  Thank you.

  Jim G

  Rename your oobe folder.

  Mac OS: \User\\Library\Application Support\Adobe\OOBE folder. To access the hidden, user library folder library user access hidden files

  Windows: \Users\\AppData\Local\Adobe\OOBE folder.  To display the hidden AppData folder, show hidden files, folders, file name extensions.

• not able to connect to oracle directly

  operating system: AIX ch5dlfp089 1 6 000B4A22D900
  Oracle: 11.2.0.1.0
  Question: created db oracle using dbca (gui). DB created successfully
  When I checked recently using putty to check the health of the db. I am able to see smon and orcl works well using
  
  PS - eaf | grep orcl.
  
  How ever when I try to connect to the db using sqlplus invites. It's showing an idle instance.
  $ sqlplus "/ as sysdba".
  
  SQL * more: Production version 11.2.0.1.0 on Mon Oct 18 00:52:08 2010
  
  Copyright (c) 1982, 2009, Oracle. All rights reserved.
  
  Connect to an instance is idle.
  
  SQL > exit
  
  oratab input shows ok
  ORCL:/Home/Oracle/app/Oracle/product/11.2.0/dbhome_1:
  
  CHECK THE BASE APPROX. values of variables
  
  $ echo $ORACLE_SID
  ORCL
  $ echo $ORACLE_HOME
  /Home/Oracle/app/Oracle/product/11.2.0/dbhome_1/
  Profile shows as follows
  
  $ cat .profile
  PATH = / usr/bin: / etc: / usr/sbin: / usr/ucb: $HOME/bin: / usr/bin / X 11: / sbin:
  
  export PATH
  
  So [s "$MAIL"] # this is at the start of the shell. Under normal conditions
  then echo operation # of '$MAILMSG', the Shell controls
  fi # periodically.
  ORACLE_SID = orcl
  export ORACLE_SID
  ORACLE_HOME=/home/Oracle/app/Oracle/product/11.2.0/dbhome_1/
  Export ORACLE_HOME
  LIBPATH = $ORACLE_HOME/lib: $LIBPATH
  Export LIBPATH
  PATH = $ORACLE_HOME/bin: $PATH
  export PATH
  
  However, I am able to connect to the db using tns
  
  $ sqlplus 'sys/Oracle123@orcl as sysdba'
  
  Connected to:
  Oracle Database 11 g Enterprise Edition Release 11.2.0.1.0 - 64 bit Production
  With partitioning, OLAP, Data Mining and Real Application Testing options
  
  SQL > EXIT
  
  
  Question: what could be the reason why I'm not able to connect db directly? without tns?
  Any error that could have happened, or a any restriction could be fixed for this access?

  Hello

  In your profile changes

  ORACLE_HOME=/home/Oracle/app/Oracle/product/11.2.0/dbhome_1

  remove the / end and try to

  Anand

• I am not able to connect to the main wifi network but can connect to the network of comments.

  Hello

  This is something new, I am facing to where I am not able to connect to a main network of airport extreme, but can connect to the network of comments. Guest network works perfectly fine while the main network does not connect to devices in the home. I also found that none of my base stations are visible in the airport utility (I Airpot extreme and Airport Express on the same network). Help, please.

  The first step in troubleshooting with this type of problem is to perform a complete network power cycle on your network. If you decide to do...

  Power off all the devices on your network... modem, routers, computers, printers, etc... in any order you want.

  Wait a minute

  Turn on the modem first and leave a few minutes, he managed by itself

  Turn on the next device that is connected to a modem and leaves turn a good minute

  Keep turn on devices one by one at a time, one minute apart, until the entire network is back

  Recheck the network and report on your results

• not able to connect to the game of google on mobile data store

  I bought gold x 2 lenovo 32 GB vibe.

  in this unit, I am not able to connect to the playstore in mobile data, it says check your connection. But Internet is active n I can navigate can open FB also.

  Yet one thing I'm not receving messages instantly in whatsapp, fb, viber. Once I open the app and then receive only the mesaages.

  and after the last firmware update whatsapp contacts are not synchronized, integrated Lenovo Security app is diabling syning whatsapp contact.

  Please give the solution.

  
  

• Not able to connect to Wifi, USB ports, bluetooth

  Hello team

  I bought the new HP laptop today. I have installed Windows 7 OS. I am not able to connect to Wifi, not be able to use the blue tooth, not be connected to the USB. I downloaded the drivers from the website of the other computer. But how can I install it with one of them works. Please help us on the question mentioned.

  Product number: G8D85PA #ACJ

  Thank you

  Sunil

  Hi Sunil_motukuri,

  Thank you for visiting the Forums HP's Support and Welcome.I would be happy to help you. I read your thread on your computer laptop 15-g030au HP and who need wireless for Windows 7 drivers. Here is a link to the drivers.

  Hope this helps you.

  Thank you.