I can get online with the Ipad, but neither my laptop without the ethernet cable. Help, please

Similar Questions

• When I try to connect with my wireless laptop will connect only to Local access. If I connect the laptop to the router with the ethernet cable, it works very well.

  VIsta - Local access only

  HI -.
  I recently moved.   I use the same router from my old apartment and I had no problem connection in the past.   Since I moved I have a new Time Warner modem (Cisco) and the modem works fine.

  The router also works very well I'm able to connect with my iPhone and IPad without any problem.

  But when I try to connect with my wireless laptop, it will only connect to Local access.    If I connect the laptop to the router with the ethernet cable, it works very well.

  It's a Dell Studio 15 with Vista.

  The computer is able to connect to wifi to other places without any problem, but for some reason that I can't connect home.   I tried to reset the modem and the router several times, but that did not help.   I tried the option repair & diagnose several times but it doesn't work.

  I tried to look for other solutions online and tried to disable IPv6, and while it helped some and I was able to connect wireless, the computer ran so slowly that it didn't seem like a good solution.

  This has been very frustrating.   Thanks in advance for any help or suggestion.
  Staci

  Hello Staciusa,

  Have you tried to change the wireless channel that your router is running at? There may be interference that could prevent the internet connection:

  Take a look at step 6 in this article that give more details about it:

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx

  If you need assistance to change the settings of the specific router, you will need to contact your router manufacturer or your internet service provider.

• What is a substitute for the migration assistant? I tried in vain for three hours to migrate files from a macbook pro to each other so that even if connected with the ethernet cable the computers never see each other.

  What is a substitute for the migration assistant? I tried in vain for three hours to migrate files from a macbook pro to each other so that even if connected with the ethernet cable the computers never see each other.

  You can connect otherwise?  USB or FireWire or love at first sight?  You can connect both machines and start the one you want to transfer to target disk mode.  If your other machine is up and running with an account on it and you just want to move files, you can simply drag and drop the FRO the machine mounted TDM, or you can use the migration wizard.

  Or, if the other machine still starts and runs, you can start both computers and connect to the same wifi network and share the hard drive like machines on the network.  Access them in the finder on the new machine files and drag-and - drop, or use the wizard migration, on wifi.

• my screen is upside down. I hit the key STROKE somw and now can go right to the top. Help, please

  my screen is upside down.  I hit a few key Strokes and now cannot get right to the top.  Help, please

  Try holding down CTRL + ALT + one of the arrows to rotate the screen.

• Pavilion dv7 Notebook - how will I know if I'm connected with the Ethernet cable or wireless?

  The notification area icon displays only a wireless connection, although the ethernet cable is connected to the laptop.  HP Connection Manager shows that both wired and wireless connections are active.  All of my previous laptop (not HP) had different icons for wireless to a wired connection in the notification area.  HP has a different icon for a wired connection?  If so, why it doesn't show in the notification area?

  obxperson99 wrote:

  Enrico, thank you.  I have installed Win7 Pro.

  The Network and Sharing Center says I'm connected wireless.

  Program of HP's "Connection Manager" shows that both the wired (ethernet) and wireless networks are connected.

  If I am always connected wirelessly with the ethernet cable plugged into my machine, how to move from the wired connection?

  Open the network and sharing Center. Look at the picture of what I have posted. Do you see where it says log in or out? Select it, and then disconnect from the wireless network. If you are also connected to the wired connecttion, then the connection should be almost transparent.

• BlackBerry smartphones can not synchronize with the USB cable plugged into charge pod

  Hello

  I read on the web site of shopblackberry.com, in the details of charge pod ( http://www.shopblackberry.com/_blackberryaccessories/cgi-bin/pd.cgi?frompage=category&page=product_d... ) that the pod can handset with charger travel or data cable for charge and/or sync with a BlackBerry smartphone. So, my question is related on a problem or a misunderstanding of me to this description.

  I want to know if we could recharge and synchronize the BlackBerry via USB cable or is only responsible for the BlackBerry when connected that way. My second question is, is it possible to synchronize the BlackBerry with the USB cable plugged into the pod or not?

  Because I got a request from one of my users about the fact that his BlackBerry 9000 can not synchronize when it is on his group.

  Thank you very much!

  Hello

  It's a loading dock. It is useful, because just drag you your "BOLD" in there and it will load (just like the 8300 Curve).
  If you want to synchronize, you can plug a usb on the side of the appliance cord. This can be done while the machine is in its dock, where the description.

  I have the same crib, but for the 8300. It's really worth buying. I'm happy with it every day.

• NB100 - unable to connect with the ethernet cable

  My netbook works very well with the wireless connection (even if I get only 4 MB when I have 10 MB connection). I visited a House of friends the other day and she does not have a wireless router.

  I plugged the cable broadand on my machine. I disabled the wireless connection and activated the network connection in network connections. I turned off then the feature wireless on the keyboard with the keys Fn & F1.

  It shows that there is a link in my taskbar, but when I try to open the internet it does not connect.

  I thought it was his connection because she had problems so today I went to another friends house and got exactly the same response.

  I decided to try the same thing at home and I disconnected the ethernet cable from my wireless router and performed the steps listed above.

  Still no joy - am I missing something?

  Tips:

  Use a static IP address, and not using DHCP.
  Disable your firewall. It can block the network connection.
  Disable network cards won't do not. If you use wired LAN, turn off wireless and Bluetooth in the Device Manager.
  Check if their ISP requires a power of Attorney, if they don't, specify the Proxy and Port in your browser settings.

• MB Pro restarts randomly with the ethernet cable is plugged

  I recently bought a thunderbolt reduction - Ethernet [1] and it works very well. The problem is that when it is plugged in, my MacBook Pro (13', 2015, i5, 8 GB) gets very hot. This isn't a problem, but the next thing is really annoying.

  Whenever I'm not load, but the ethernet cable is connected, and MacBook goes into sleep mode, the system turns off instead. Thus, for example, when I don't have the power cable and if go for 5 minutes, the system automatically sets the mode 'sleep'. When I come back, it is turned off, and when I hit the power button, a black screen with the Apple logo and a text in several languages, saying that the system restarted because of a problem. After that, MacBook starts normally.

  The same phenomenon occurs:

  • When the power cable is not connected and I close the screen
  • When the power cable is not connected and I SLEEP manually the MacBook
  • When the screen is closed and I plug the power or the ethernet cable

  I use OS X 10.11.

  [1]: shot of lightning-Ethernet reduction ter http://www.apple.com/shop/product/MD463LL/A/thunderbolt-to-gigabit-ethernet-adap

  The SMC reset may help:

  https://support.Apple.com/en-us/HT201295

  Ciao.

• I just bought an Airport Extreme and try to put in place.  I have Fios cable with a router.  I can not get anything except a blinking orange light.  After reading the instructions, it seems that the problem with the ethernet cable but I

  Must not exceed the flashing orange light.  have tried three ethernet cables to the Fios router.  All thoughts

  What extreme version do you have?

  Test the cables connecting the airport to your Mac with them and see if the ethernet works on Mac. Green connectivity light should go... If it fails, then the AE died.

  Please do a factory reset, then try again.

  Sometimes Mac airport utility works well... If you have the preference or iphone ipad, download and use iOS version airport utility and try it for configuration... It is much less awkward.

• Updates of windows installed and now unable to get online with the Explorer.

  I am running windows vista and installed updates and now cannot get online.  I tried to run the system restore, but that did not help.  This happened once before when the only web sites that I could access were secure web sites, I have changed the security settings and that fixes the problem.  Nothing works for now.

  I'll get more info from my computer at home tonight and add to that tomorrow.

  Thank you!!

  What application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?

  A (another) Norton or McAfee application has already been installed on this machine (for example, a free trial version which is preinstalled when you bought it)?

  =========================

  Error message after you install an update of Windows Internet Explorer from Windows Update or from Microsoft Update: "cannot display the webpage".
  http://support.Microsoft.com/kb/942818

  If not help to tweak the parameters of your third-party firewall, try the following:

  1. disable your antivirus, all modules of Norton (as applicable), a real-time protection provided by an anti-spyware application (with the exception of Windows Defender; includes the Tea Timer of Spybot, AVG AS guard.exe, SpySweeper guards, etc.), disable the third-party firewall AND THEN select Windows Firewall.

  NB: Now you're "working without a net": no to ANYTHING else online (e.g., navigation, reading e-mail, chat) except #4 below until your antivirus application has been reactivated!  If you use a free ZA firewall, you may need to uninstall instead of disable.

  2 uninstall 'update Cumulative security for Internet Explorer 7 (or 8) for Vista (KB976325)' or "Security Update for Microsoft Windows (KB976325)" via start | Control Panel | The Maintenance and the system (if you use Classic view, skip this step). Windows Update | Installed updates day & reboot.

  3 d - c #1 above.

  4 manually run Windows Update and install important updates available (i.e. KB976325).

  5 reboot & make sure everything in #1 above is on again and, if necessary, disable the Windows Firewall and enable (or reinstalling) your third-party firewall.

  =====================================

  For individuals, please visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy.  If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Problem with the version number - help please.

  Hello, my Avast reports that my Skype is outdated and must be updated with the latest version, (7.8.0.102), but when I goto Skype help and updates, Skype says I have the latest version already installed (7.7.64.103), what happens here, can someone explain the discrepancy PLEASE?

  Cheers from TekyTek

  For later use, download (download Skype) on this site section, allways will give you the installer for the latest version (7.8 in this case) when available, even if your ' check for update ' tell you that you have the latest version.

  Just make the file skypesetup right click and select Properties, the details tab will tell you which version the Downloader is for (or in the case of a complete configuration file, what version it is).

• Assistant of migration with the ethernet cable?

  Hello! I have a new iMac and I want to use the Migration Wizard to transfer my old files from my old Macbook Pro to my new iMac. Love at first sight is not my old Macbook Pro only Firewire 800, USB 2.0 and an Ethernet port. So I thought I will use the Ethernet on Mac port with a CAT6 ethernet cable to connect directly to a faster transfer, but I don't know how it works, because the drive is not appear when you use Migration Wizard. I followed the instructions from Apple: https://support.apple.com/en-us/HT204350

  But when looking for sources, it does not find my Macbook Pro drive so it can start the Migration process. Do you need to set up something else to make it work? Or is it beter to this with Firewire 800, which is my other option. Hope someone can help me ;-) Thank you Cloe

  Ethernet requires both computers to be started normally

  FireWire should be started using the target to the source computer and the computer started normally host

  OS X Lion mountain: transfer files between two computers using target disk mode

• Pavilion dv6 - 2171 Wifi's stay, even with the Ethernet cable is plugged.

  Hello

  I just did a clean install of Windows 7 Ultimate 64 bit on my Pavilion DV6 - 2174ca, installed all the drivers of necesasry and worked on almost all of the bugs.

  But I had problems with my network drivers. I have all the drivers available of Net installed and activated, but when I plug in and ethernet in to a wired connection Wifi stays on. In order to show him a wired connection, I need to go to Device Manager and disable the driver Broadcom 43225.

  I installed the network drivers are:

  -Bluetooth Device (personal area network)

  -Bluetooth Device (RFCOMM Protocol TDI heading)

  -Broadcom 43225 802.11b/g/n

  -Realtek PCIe GBE Family Controller

  I do not want to go in Device Manager every time I plug an ethernet. Can you offer any suggestions? We hope to hear soon. Thank you!

  Hello

  No need select Manager of Devive to disable. 3 clicks and the wireless will be stop.

  (a) click # 1: the icon wireless (lower-right).

  b click on # 2: SSID

  (c) click n ° 3: disconnect

  Or try please answer to Diana on the following discussion:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/how-make-win-7-to-prefer-wired-over-wireless/97ae998b-5743-E011-9767-d8d385dcbb12

  Kind regards.

• I have a problem with the numbers. Help, please!

  I have a problem with the numbers. I am trying to create a formula that can add a cell only when another cell with a pop-up menu returns on a specific pop.  I can't ignore the cell if it is not on specific pop upward.

  assuming the cell with pop's cell A1

  and if the context menu contains items:

  YES

  NO.

  MAYBE

  and the value you want to add in cell A2

  You can add the value in cell A2 when the context menu is 'YES' like this

  = if(A1="YES", A2, "") +.

  where is the expression that adds other cells if you want

  could be another cell

  = If (A1 = "YES", A2, "") + B2

  or a range of cells

  = If (A1 = "YES", A2, "") + sum (B2, D2, G2:H5)

• Problem with the procedure. Help, please

  Schema: HR

  Here is the procedure I created, when I compile the procedure it works very well and without errors or warnings are displayed. However, when I run, I get "01031. 00000 - "insufficient privileges" "error. "I tried 'GRANT ALL HR', 'ANY GRANT to HR'.," to HR WITH ADMIN OPTION GRANT ' nothing works. Not sure is code that has questions or privileges.

  create or replace procedure new_create_PROC IS
  BEGIN
  EXECUTE IMMEDIATE 'CREATE TABLE NEW_CREATE1(EMP_ID NUMBER,EMP_NAME VARCHAR2(20))';
  END;
  /
  
  
  EXECUTE new_create_PROC;
  
  TE new_create_PROC;
  /
  

  Help, please.

  You are connected to the DB under what user? You must grant this user the CREATE TABLE privilege.