MB Pro restarts randomly with the ethernet cable is plugged

Similar Questions

• Pavilion dv6 - 2171 Wifi's stay, even with the Ethernet cable is plugged.

  Hello

  I just did a clean install of Windows 7 Ultimate 64 bit on my Pavilion DV6 - 2174ca, installed all the drivers of necesasry and worked on almost all of the bugs.

  But I had problems with my network drivers. I have all the drivers available of Net installed and activated, but when I plug in and ethernet in to a wired connection Wifi stays on. In order to show him a wired connection, I need to go to Device Manager and disable the driver Broadcom 43225.

  I installed the network drivers are:

  -Bluetooth Device (personal area network)

  -Bluetooth Device (RFCOMM Protocol TDI heading)

  -Broadcom 43225 802.11b/g/n

  -Realtek PCIe GBE Family Controller

  I do not want to go in Device Manager every time I plug an ethernet. Can you offer any suggestions? We hope to hear soon. Thank you!

  Hello

  No need select Manager of Devive to disable. 3 clicks and the wireless will be stop.

  (a) click # 1: the icon wireless (lower-right).

  b click on # 2: SSID

  (c) click n ° 3: disconnect

  Or try please answer to Diana on the following discussion:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/how-make-win-7-to-prefer-wired-over-wireless/97ae998b-5743-E011-9767-d8d385dcbb12

  Kind regards.

• What is a substitute for the migration assistant? I tried in vain for three hours to migrate files from a macbook pro to each other so that even if connected with the ethernet cable the computers never see each other.

  What is a substitute for the migration assistant? I tried in vain for three hours to migrate files from a macbook pro to each other so that even if connected with the ethernet cable the computers never see each other.

  You can connect otherwise?  USB or FireWire or love at first sight?  You can connect both machines and start the one you want to transfer to target disk mode.  If your other machine is up and running with an account on it and you just want to move files, you can simply drag and drop the FRO the machine mounted TDM, or you can use the migration wizard.

  Or, if the other machine still starts and runs, you can start both computers and connect to the same wifi network and share the hard drive like machines on the network.  Access them in the finder on the new machine files and drag-and - drop, or use the wizard migration, on wifi.

• Pavilion dv7 Notebook - how will I know if I'm connected with the Ethernet cable or wireless?

  The notification area icon displays only a wireless connection, although the ethernet cable is connected to the laptop.  HP Connection Manager shows that both wired and wireless connections are active.  All of my previous laptop (not HP) had different icons for wireless to a wired connection in the notification area.  HP has a different icon for a wired connection?  If so, why it doesn't show in the notification area?

  obxperson99 wrote:

  Enrico, thank you.  I have installed Win7 Pro.

  The Network and Sharing Center says I'm connected wireless.

  Program of HP's "Connection Manager" shows that both the wired (ethernet) and wireless networks are connected.

  If I am always connected wirelessly with the ethernet cable plugged into my machine, how to move from the wired connection?

  Open the network and sharing Center. Look at the picture of what I have posted. Do you see where it says log in or out? Select it, and then disconnect from the wireless network. If you are also connected to the wired connecttion, then the connection should be almost transparent.

• When I try to connect with my wireless laptop will connect only to Local access. If I connect the laptop to the router with the ethernet cable, it works very well.

  VIsta - Local access only

  HI -.
  I recently moved.   I use the same router from my old apartment and I had no problem connection in the past.   Since I moved I have a new Time Warner modem (Cisco) and the modem works fine.

  The router also works very well I'm able to connect with my iPhone and IPad without any problem.

  But when I try to connect with my wireless laptop, it will only connect to Local access.    If I connect the laptop to the router with the ethernet cable, it works very well.

  It's a Dell Studio 15 with Vista.

  The computer is able to connect to wifi to other places without any problem, but for some reason that I can't connect home.   I tried to reset the modem and the router several times, but that did not help.   I tried the option repair & diagnose several times but it doesn't work.

  I tried to look for other solutions online and tried to disable IPv6, and while it helped some and I was able to connect wireless, the computer ran so slowly that it didn't seem like a good solution.

  This has been very frustrating.   Thanks in advance for any help or suggestion.
  Staci

  Hello Staciusa,

  Have you tried to change the wireless channel that your router is running at? There may be interference that could prevent the internet connection:

  Take a look at step 6 in this article that give more details about it:

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx

  If you need assistance to change the settings of the specific router, you will need to contact your router manufacturer or your internet service provider.

• computer goes to sleep as soon as the ethernet cable is plugged in and don't wake up

  When the ethernet cable is plugged into my pc, it immediately goes to sleep and don't wake up without a difficult start. As long as the cable is connected, the computer will not load windows, immediately go to sleep before my desktop appears. My laptop is connected wirelessly without any problems at all and when connected with a cable, no problem either. ISP says it's a pc no matter not a modem problem, there is a conflict, but they don't know where.

  I am running windows Vista Home Basic, a cisco modem, do not know what model.

  Any help would be appreciated.

  Hello

  1. don't you make changes to the computer until the problem occurred?

  I suggest you to check the parameters of the power management of the device on the network adapter.

  To correct the settings please follow these steps.

  (a) click Start, type device in the box start the search and then click on Device Manager in the programs list.

  (b) in the user account control dialog box, click continue.

  (c) in Device Manager, expand network adapters.

  (d) right click on the network driver and then click Properties.

  (e) click the power management tab.

  (f) click to uncheck the checkbox allow the computer to turn off this device to save power , and then click OK. If the option is checked, then uncheck the option and apply the settings.

  Once you have performed the steps, restart the computer so that the changes take effect, and then check the result.

  Hope this information is useful.

• Satellite P300-173 never off when the ethernet cable is plugged or WIFI

  Hello

  I can't stop my P300 correctly.

  Whenever the ethernet cable is plugged or wifi is connected, stop work until the screen goes black but the power remains on: fan, always active LEDs. The only way to stop then is to press the power button.

  As the network is always connected, it's really annoying.

  Can you please help?

  Thank you!

  ER

  Hello

  Very strange problem
  First have you checked if you use the latest version of the BIOS?
  Please check this!

  On the European driver Toshiba page you will always find the latest BIOS and divers.

  Secondly, I would recommend disabling more upward on LAN option in the BIOS and in properties (device-> LAN properties-> Advanced tab management) LAN card

  Check if this may help solve this problem

• NB100 - unable to connect with the ethernet cable

  My netbook works very well with the wireless connection (even if I get only 4 MB when I have 10 MB connection). I visited a House of friends the other day and she does not have a wireless router.

  I plugged the cable broadand on my machine. I disabled the wireless connection and activated the network connection in network connections. I turned off then the feature wireless on the keyboard with the keys Fn & F1.

  It shows that there is a link in my taskbar, but when I try to open the internet it does not connect.

  I thought it was his connection because she had problems so today I went to another friends house and got exactly the same response.

  I decided to try the same thing at home and I disconnected the ethernet cable from my wireless router and performed the steps listed above.

  Still no joy - am I missing something?

  Tips:

  Use a static IP address, and not using DHCP.
  Disable your firewall. It can block the network connection.
  Disable network cards won't do not. If you use wired LAN, turn off wireless and Bluetooth in the Device Manager.
  Check if their ISP requires a power of Attorney, if they don't, specify the Proxy and Port in your browser settings.

• T460 touchpad responds liked when the Ethernet cable is plugged

  Hello

  I bought a brand new ThinkPad T460 ten days ago and I noticed that when I plug in an Ethernet cable, the touchpad responds: just a few clicks and taps are missed, the movement is slow and and sometimes temporarily blocked. The touchpad comes alive again as soon as the Ethernet cable is disconnected. The trackpoint and trackpoint button above the touchpad are not affected, only the touchpad starts to misbehave.

  This happens on both Windows and Linux, this isn't a problem of specific operating system. Furthermore, I checked to see if I am running the latest version of the BIOS, and I am. And there are no problems when you use the wireless adapter, but one of the reasons why I bought a ThinkPad was she has a port Ethernet, so not being able to use it would be extremely disappointing.

  I checked to see if there are any IRQ conflicts for the touchpad, but could find none. The problem occurs when the computer is plugged in and when it runs on battery only. I also tried two different cables in the same router, each in a different router port, and the problem persisted.

  I'm using the latest drivers for Windows 7 directly on the Lenovo site, and Arch Linux with kernel 4.4.5 - the Ethernet card is considered:

  e1000e [2.751703]: Intel® PRO/1000 3.2.6 - k network driver
  e1000e [2.751705]: Copyright (c) Intel Corporation 1999-2015.

  Should I expect it is fixed with a BIOS update, or do I have to contact guarantee? It is unacceptable to live with it.

  Tried in another House as promised, and the touchpad works very well with cable Ethernet is plugged. Also, before you leave the House with the problem, I discovered that the problem occurs only when the cable from my ISP switch is plugged into my router.

  Respect my opinion that this machine deserves a stronger touchpad, but apparently is not due to lack of computer - under normal circumstances, there is no problem with the touchpad.

  I'm stumped on how to proceed. Can I use a multimeter on the ISP switch from cable, but I'm not sure what to check (voltage? how does and between what son?). I'll also look into the suggestion of ferrite, I don't know where they are available - this thread is first heard of them.

  Anyway, I wanted to just erase Lenovo name on it.

• Assistant of migration with the ethernet cable?

  Hello! I have a new iMac and I want to use the Migration Wizard to transfer my old files from my old Macbook Pro to my new iMac. Love at first sight is not my old Macbook Pro only Firewire 800, USB 2.0 and an Ethernet port. So I thought I will use the Ethernet on Mac port with a CAT6 ethernet cable to connect directly to a faster transfer, but I don't know how it works, because the drive is not appear when you use Migration Wizard. I followed the instructions from Apple: https://support.apple.com/en-us/HT204350

  But when looking for sources, it does not find my Macbook Pro drive so it can start the Migration process. Do you need to set up something else to make it work? Or is it beter to this with Firewire 800, which is my other option. Hope someone can help me ;-) Thank you Cloe

  Ethernet requires both computers to be started normally

  FireWire should be started using the target to the source computer and the computer started normally host

  OS X Lion mountain: transfer files between two computers using target disk mode

• I just bought an Airport Extreme and try to put in place.  I have Fios cable with a router.  I can not get anything except a blinking orange light.  After reading the instructions, it seems that the problem with the ethernet cable but I

  Must not exceed the flashing orange light.  have tried three ethernet cables to the Fios router.  All thoughts

  What extreme version do you have?

  Test the cables connecting the airport to your Mac with them and see if the ethernet works on Mac. Green connectivity light should go... If it fails, then the AE died.

  Please do a factory reset, then try again.

  Sometimes Mac airport utility works well... If you have the preference or iphone ipad, download and use iOS version airport utility and try it for configuration... It is much less awkward.

• Apple TV (4th gen) faster with 5 GHz WiFi with the ethernet cable

  When my Apple TV is connected to my network via 5 GHz WiFi it gives me a faster speed (about 120 Mbps) connections it makes when I plugged it on my network (about 45 Mbps) ethernet cable.  Why is this?  I thought that the ethernet would give me the fastest connection possible.

  The ethernet port on all ATVS (including the 4th generation) is only 100 Mbit/s. The actual speed depends on the quality of your network as the routers, switches and cables components and of course it depends on the length of your ethernet cable and if it is damaged in any way (folded or crushed). And finally, that depends on how fast you have actually measured, on your local network speed, or speed on your WAN.

• My Windows XP laptop does not connect to my 2WIRE router wireless, but do my other laptops. It will only connect with the ethernet cable. What is the problem?

  What I'm doing.

  1. my laptop is a Toshiba XP

  What serial number and model of Toshiba?

  What type of encryption 2wire router uses for now? Type of WEP or WPA? If the latter do you know if your XP laptop wireless card supports WPA (some older cards only). If you find that this is the problem, you can go to the WEP encryption or buy a WPA compatible device to use instead of the current device on the XP laptop.

  If you don't know how to find this information...

  The range and the model are probably on a sticker on the bottom of the laptop.

  I think that there is a sticker on the side of 2wire routers (leastways are those provided by BT) gives you the encryption key and this might also state what is the type of encryption. Or, if not, open a web browser such as internet explore/firefox etc and go to http://gateway.2wire.net, somewhere on the router admin pages, you will find information on wireless security/encryption.

  Regarding the card laptop wireless, I can help with this if you give me the range and the model as requested above. I can, also, be able to determine from the description of the device in Device Manager. Click Start, click Run, type devmgmt.msc and press ENTER. Network adapters (click on +) and transcribe the wireless adapter that there are listed in a response to this post.

  Tricky

• printer is not found when connected to the router with the ethernet cable

  My c6280 used to print wireless (not a wireless printer) because I had hooked to the router.  Now, it won't work - I'm on Mac OSX Lion.  I tried to delete the printer and reinstall.

  Hello

  Please make sure to remove the software completely, because there is no plans for Lion.

  While the printer is connected to your network,

  Go into System Preferences > print & scan and click on the sign more.

  Select your printer and the driver will download automatically the Apple software update.

  For more information, you can follow the document below:

  http://support.HP.com/us-en/document/c02911238

  If the update fails to install Apple servers, download and install the package of the latest version of the HP to Spple printer software:

  http://support.Apple.com/downloads/DL907/en_US/HewlettPackardPrinterDrivers2.7.2.dmg

  After completing the installation, add your printer as explained previously.

• Cisco router restarts randomly with Bus error

  Cisco router restarts randomly with the following error:

  System has been restarted by error of bus to PC 0x4183614C, speech 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013

  I've pasted below see the chimneys and release the version.

  view the stacks

  
  

  Minimum factory chimneys:

  Format name / free

  5396/6000 inspect Init Msg

  Subsystem SPAN 5368/6000

  58920/60000 EEM Auto record Proc

  Automatic start of 4772/6000 upgrade process

  DIB 5164/6000 error message

  HAND OF SASL 5396/6000

  4968/6000 LICENSE DEFAULT AGENT

  5368/12000 Init

  4216/6000 update prst

  4384/6000 VPN_HW_MIB_CREATION

  5188/6000 RADIUS INITCONFIG

  Update process random rom 2128/3000

  8356/12000 SSH process

  Stats URPF 5316/6000

  Interruption of battery level:

  Level named format / unused

  Network interfaces 1 1484828 6284/9000

  2 3264990 8548/9000 DMA/Timer Interrupt

  3 1 8388/9000 PA Int management Manager

  Console 4 115 8612/9000 Uart

  External interrupt 5 0 9000/9000

  NMI 7 223352 8564/9000 interrupt handler

  Spurious interrupts: 11

  System has been restarted by error of bus to PC 0x4183614C, speech 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013

  Software of 2800 (C2800NM-ADVSECURITYK9-M), Version 12.4 (24) T, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Updated Thursday 25 February 09 17:55 by prod_rel_team

  Image text-base: 0 x 40011240, database: 0x42B41940

  The failure of the system stack trace:

  FP: 0X472252B8, RA: 0X4183614C

  FP: 0 X 47225310, RA: 0X418312F8

  FP: 0 X 47225348, RA: 0X41647DC0

  FP: 0X472253A8, RA: 0X4164A8F4

  FP: 0 X 47225428, RA: 0X4164B248

  See the version

  
  

  Cisco IOS software, 2800 Software (C2800NM-ADVSECURITYK9-M), Version 12.4 (24) T, RELEASE SOFTWARE (fc1)

  Technical support: http://www.cisco.com/techsupport

  Copyright (c) 1986-2009 by Cisco Systems, Inc.

  Updated Thursday 25 February 09 17:55 by prod_rel_team

  ROM: System Bootstrap, Version 12.4 (1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

  availability of Cisco is 28 minutes

  System returned to ROM by bus to the 0x4183614C PC error, address 0 x 95848 at 09:30:28 UTC Tuesday, April 23, 2013

  System image file is "flash: c2800nm-advsecurityk9 - mz.124 - 24.T.bin".

  This product contains cryptographic features and is under the United States

  States and local laws governing the import, export, transfer and

  use. Delivery of Cisco cryptographic products does not imply

  third party approval to import, export, distribute or use encryption.

  Importers, exporters, distributors and users are responsible for

  compliance with U.S. laws and local countries. By using this product you

  agree to comply with the regulations and laws in force. If you are unable

  to satisfy the United States and local laws, return the product.

  A summary of U.S. laws governing Cisco cryptographic products to:

  http://www.Cisco.com/WWL/export/crypto/tool/stqrg.html

  If you need assistance please contact us by mail at

  [email protected] / * /.

  Cisco 2821 (revision 53.51) with 1036288K / 12288K bytes of memory.

  Card processor ID FCZ1017732F

  2 gigabit Ethernet interfaces

  2 modules of virtual private network (VPN)

  Configuration of DRAM is wide with parity 64-bit capable.

  239K bytes of non-volatile configuration memory.

  250880K bytes of ATA CompactFlash (read/write)

  Configuration register is 0 x 2102

  You want to use the tool interpreter of output for this work:

  http://www.Cisco.com/pcgi-bin/support/OutputInterpreter/home.p

  For more information about the resolution of crashes, see this article:

  http://www.Cisco.com/en/us/products/HW/IAD/ps397/products_tech_note09186a00800b4447.shtml

  In this case, it looks like CSCsy09250, described here:

  http://www.Cisco.com/en/us/products/CSA/Cisco-SA-20100324-SCCP.html

  You should contact Cisco for the software updated by following the instructions of this bulletin.

  That crash possibly caused by part of sone intentionally sends out packets malformed to your device, so if you have reason to believe that someone in your community could run metasploit or similar "Penetration Testing" tools, you can look into that as well.