I see the BIOS time without restarting the host computer?

Similar Questions

• Don't see the hosts file, I'm trying to block the ads of my browsers

  Hello

  I'm trying to block ads in my browser but when I go to c; Windows/system32/drivers/etc I do not see the Host file I virtue see a file while properties indicates that it is 5 archives. I need to add some info on the hosts file how to make this file show. Although I don't see it when I try to paste a modified hosts file it won't allow replacement of Martin

  I use XP.

  Thank you

  Catalin

  Click Start--> go in run and paste the following entry: %systemroot%\system32\drivers\etc

  You now see the hosts file?
  If this is not the case, try this:
  1. click on start go to run-->
  2. tap------(literally just a------and nothing else)
  3. press on enter
  4. click on Tools--> folder--> view options
  5. make sure that a small black dot appears next to 'display files and folders '.
  6. scroll down for 'show hidden files and folders' and remove the checkbox from "Hide protected files (recommended) operating system.
  7. click on 'yes '.
  8. click on 'Ok '.
  9. click on start--> go in run and paste the following entry: %systemroot%\system32\drivers\etc
  If you * see the hosts file now, right-click on it and make sure that there is no check mark 'read only' and 'hidden' boxes... If they are verified, then remove the check.
  Note: you should not have to perform steps 1 through 8 to view the hosts file; the hosts file is visible even with these settings, the default value (for example, when files are hidden you should always see the hosts file), but you may have a spyware infection that has tried the hide and prevent changes in the host file (to prevent you from making corrections in the file which made spyware)
  assuming that you have made any customizations to this file, it should appear as the default value listed in this Microsoft article: http://support.microsoft.com/kb/972034
  If it looks not to the default file listed at this URL, then you can recreate the file by using the templates included in this document KB

• Unable to communicate with the host computer using the network University compactRIO

  Please move this topic to the appropriate section if it is not the right section. I can't locate a Council called the compactRIO. Thank you very much.

  I encounter this problem of network communication with my cRIO 9067. the linklocal or USB connection is fine but not static IP connection on the network. I contacted the it Department to assign me a static IP address for my MAC address of cRIO. In our University, they block only unknown MAC address access and the cRIO is in the whitelist. Here are the details

  cRIO attributed to IP address: 129.12.54.xxx, tried both netmask 255.255.255.0 and 255.255.0.0, no luck

  the host computer's static IP address: 129.12.50.xxx, subnet mask 255.255.255.0 (information of cmd - ipconfig)

  First question would be: they are on the same subnet? I need to make sure that even if scientists confirm that.

  Secondly, I followed https://www.ni.com/getting-started/set-up-hardware/compactrio/static-ip by using the IP address assigned, but not luck. I've noticed that I configure same address type cRIO static IPv4 using the USB connection or for local link mode, she went in DHCP mode or Local link once I unplug the USB and restart it.

  Whenever I restart MAX, connect the cRIO and my host to Ethernet jack on the wall, it shows the DHCP mode or link with assigned Local 129.12.54.xxx IP and the subnet mask 255.255.255.248. In addition, I am not able to change it in a drop-down list even after removing it and restart MAX indicated by tutorials OR.

  If you need more information, please let me know.

  Help, please!

  Jinyu

  Dear Mikko,

  I am pleased to tell you that the problem has been resolved. The cRIO works very well.

  The reason why it does not work is in first place because they are in the other subnet. For my school, my host is 12x.1x.54.130 and the IP assigned to my cRIO is 12x.1x.54.131. the subnet mask is 255.255.255.0 number marked in red must be the same for the cRIO is connected correctly.

  Kind regards

  Jinyu

• When the computer 'host' is accessible by the 'guest' on the network computer, the host computer crashes hard.

  There is no error message, making it difficult to diagnose. There are two computers running Vista, fully patched, connected via a network of small size. (Microsoft MSE, no virus, start using activated, etc. "It is clean). When the computer goes to * any * file of the host computer, the host computer crashes immediately. There is no error message, freezing of mice, all hard disk activity stops, it stops absolutely everything. The continuous guest PC works well, it simply notes that the host computer is "not available". Someone saw something like that? I certainly have not. It's far too vague to diagnose.

  I looked on the event logs and couldn't find anything saying. I disabled and re-enabled the network shares, etc. Because they are built Lenovo desktop computers, I have a difficult time to do a "repair", but I guess I could give that a shot with some Vista discs. As I understand it, these computers are not often with Vista bootable discs.

  It is essential that I can diagnose it. In almost twenty years of THIS I've never seen anything this vague and almost impossible to diagnose.

  Any help or advice would be greatly appreciated. Is it all the same to make a "full reset" or "Refresh" of networking in Vista? Who could do.

  I also note that it is a recent issue, these systems worked very well for a while and it's a change suddenly. Particularly curious because I locked the Windows updates to update only when I say so... and I didn't have lately.

  Have you tried to replace the NETWORK card on the computer that crashes? If not, it's what I would do then. MS - MVP - Elephant Boy computers - don't panic!

• Why will my router stops transmitting the internet signal after that I turned off the host computer?

  Hi members of the community.

  first of all, my setup:

  modem - router (wrt320n lynksis, yesterday I uplodaded latest firmware - it does not help)---(par câble), PC (windows 8)
  l
  l
  various devices (cable TV, wireless: laptop computer (windows XP), phones (Iphone, android, phone etc.))
  Second question:
  Until now, I had no problem with router, but as I connected the new PC, with windows 8 is installed, the router, I began to encounter the following problem: I turn the host computer (wired, PC with windows 8) off after a minute or two the router (if not always on) continues to transmit the internet signal with other devices (wired (TV) and other wireless).  What's also interesting is that, when I unplug the PC from the router ethernet cable (when the PC is turned off), the router begins to function normally. Why and how to fix it? It seems that the PC would stop the router in the transmission of the signal.
  I would apreciate any help I could get. Because the router is working otherwise fine (when the computer host is turned on when the PC is disconnected from the it), I guess it has something to do with the windows configuration.
  Thank you all,.
  Sincerelly, Janez

  Hi there... we have a different router, but I had exactly the thing happens to me when my husband bought his new computer. After hours of technical support that gave no results of our router manufacturer, I did some research on the web, a vast and I think I found the solution.

  Go to control panel > system and security > system > Device Manager > network adapters > find your network card (mine says in time real PCIe GBE) open cela, go to power management and uncheck the BOX allow the computer to turn off this device to save power.

  After that I did that my router is no longer turns off/goes to sleep when my computer is. Offshore.

  Give that a try, and if all goes well, it will help you too.

• error "could not complete the configuration of the ha agent on the host computer.". misconfiguration of the installation of the host network.

  Hola y buenos dias, he puesto 2 hots directly in una DMZ y al activar el error HA da este:

  "Unable to complete the configuration of the ha agent on the host computer.". misconfiguration of the installation of the host network.

  ESTOS son gemelos servidores y poner esta durante 2 Años last config antes han estado dentro infraestructuras en a cluster con otros 4 running perfectly. Ante nueva situation that met responsible security perimeter solo our esta posibilidad por lo as procedimos dio el a preparar los hots ante the nueva config enchufamos estos y an el swhitch of the demilitarized zone.

  Según me ha EDI el responsible of security perimeter, todo el trafico desde estos 2 hots hasta el esta allowed vCenter y asi mismo el cortafuegos responde al trafico ICMP a estos hots (este tema that he read in various Québec sites are important para el HA).

  Version of hots los Esxi 4.1.0 721871

  Me falta algo o tengo algo configurado evil?

  Important Algo a revisar?

  A greeting is gracias por adelantado

  Buenas

  Me designed that tendras 2 con 2 direcciones distintas vmkernel (lo del tema Las vlan y las tarjetas're menos ahora lo)

  Prueba has see the resolución desde el propio ESXi, prueba el uno a otro por both vmkernel ping, etc...

  A malas, saca ambos nodos del cluster y vuelve a unirlos con desactivado, cuando tengas los 2 HA, activa HA of nuevo y con eso you can smear of dudas so por el tema del VC University y UN vicio en BBDD.

  If todo esto falla, have as plantearte touch en el aam, are fairly complejo y peligroso if no to sabe hacer correctamente.

• Binds a guest operating system to one of the two network adapters on the host computer?

  Sorry if the topic is confusing.  I have a host operating system to Server 2008 running on a server that has two network jacks.  Allows to call an (192.168.10.24) and B (192.168.10.25).

  My guest operating system is set to bridged with the IP 192.168.10.26 mode

  I want to say VMWare to always use A NIC when it comes with this guest operating system.  Is this possible?

  In my (Control Panel Windows) network connections, I see my two NICs A and B as well as VMWare Network Adapter WMnet1 and VMnet8.

  Thank you!

  Run the utility for configuring the network (vmnetcfg.exe) as an administrator on the host computer, disable the automatic bypass, set vmnet0 to one of your physical network cards and a virtual NETWORK adapter not used, such as VMnet2, and then assign the other physical NIC. Then to your comments, change its settings and select vmnet0 or vmnet2.

  Guy Leech

  VMware vExpert 2009

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• incomplete printing of letters, but only from the host computer

  I have a recurring problem with my print where the last line of each paragraph does not correctly print outs.  the bottom of the letters are cut off.  In addition, this problem occurs only on the host computer in our network.  and maybe when I use microsoft word, excel or publisher. (I print web pages properly) I did the following:

  1 printer checked drivers were updated and they are.

  2. ran a clean ink cartridge program, did not work.

  3. install new, both ink cartridges in black and color.

  4. selected 'best' for the quality of printing, this improves the problem but does not eliminate the problem.

  hardware information:

  printer hp officejet j5780 all-in-one

  host computer: dell desktop 2009 windows vista

  portable printer: notebook computer dell 2009 windows vista

  Sincerely, melody

  I have provided a link to documents from HP that can help solve the problem you're having with printing of cut.

  http://support.HP.com/us-en/document/c01671543

  There are also links in the above link which may help even further.

• "HA agent on the host computer was arrested.

  After quick vMotioning a number of virtual machines on an esx host I get an error on this host that "HA agent on [host] in cluster [NOMCLUSTER] in [datacentername] has an error: HA agent on the host computer was arrested" this could be the cause?

  Thank you

  "reconfigure for ha" is not impact on any virtual machine running or he kickoff an HA event, but you work with just the HA agent, that's all.

• Error message: «the virtual network on the host computer drivers are incompatible...» »

  Just bought a new computer that is running Windows Vista Ultimate 64-bit.

  I installed VMWare Workstation 6.5.1 build 126130.

  I copied on a machine virtual from the old computer (running Windows XP Pro and VMWare Workstation 5.0.0 build 13124). I improved this VM Workstation 6.5. This virtual machine is currently running Windows XP Pro.

  When I run the virtual machine on the new computer, I get the following error message:

  "The virtual network on the host computer drivers are incompatible with the installed application of VMWare. Version expected 5. Please reinstall the product. Virtual device Ethernet0 will start disconnected. »

  Note that the virtual machine runs; I don't have any network capacity.

  I read the thread http://communities.vmware.com/thread/186731, who seems to have the same problem. He had installed 6.5 on 5.5; When he uninstalled and deleted all of the directories, and then reinstalled everything went well.

  I don't have any product VMware existing on the computer that would cause this type of conflict.

  So, what should I try to fix this?

  Thank you

  Wayne

  If you want to install only vmnetadapter, open cmd as admin in vmware workstation dir and run;

  "rundll32 setupapi, InstallHinfSection VMnetAdapter1.Install 128% CD%\netadapter.inf"

  You can also repeat for vmnetadapter8.

  If it does not run as above

  "vnetlib - install devices.

  Joakim

• Power of fire-URL blocking - how to see the hosts?

  Hello

  I work with the implementation of a system of firepower on an ASA5525X. I activated the blocking of certain categories of URL, it works fine and I can see that a number of classes of forbiddel connections is arrested. But how it go down and see what internal hosts attempt to access the URL forbiddel? Standard reports or dashboards that gives this information?

  Kind regards

  Thor-Egil

  Hello, what are you using for the configuration of the module of firepower? ASDM or firepower Management Center (FMC)? In WCF, you can get detailed information about each transaction in the tab analysis-> connection-> events. Please, see the attachment.

  But first, you must configure journaling in access policies.

• My guest can not see the host or cannot communicate with the network, networking is set to bridged, host operating system is Windows XP sp3

  Hello from Spain,

  I am running vmware workstation 6.0.2 on a windows xp sp3 with two virtual machines, a xp and a windows 2003 Enterprise edition. Non of my guests can't see the computer host or other computers on the LAN and host when I click on show "Entire network", "Microsoft Windows network" I see that the domain for which the guests but not the domain controller when I double click the icon of the domain. Networking is set to connected by a bridge to the NETWORK adapter connected to the LAN.

  Thank you.

  Hello

  No message in the post

  route print at the command prompt to the host and the guest and send report

  Prakash

• VMware Workstation 7 - comments cannot connect to the host computer

  My problem is compounded by the fact that I've upgraded to VMware 7 and added several virtual Win7 64 virtual machines at the same time so I don't know what (or who) is causing the problem.

  I have 2 host computers running Windows XP 64 and VMware 7.  Firewall is turned off on all real and virtual computers and antivirus software disabled to facilitate debugging.

  I can 'see' host an extra to my network of machines, but I can't connect any virtual machine (Win XP 64 or Windows 7 64) to the drives or folders in a. host Virtual Machines of all the flavors to host B (as can host B himself) can connect to drives and folders in host A or B computers.

  I'm really confused, because it is a new problem in a network that worked without problem for a long time.

  Thank you

  k

  kriemer wrote:

  Scissor

  I was using AVG Anti-virus v8.5.  I uninstalled since then to try to resolve the problem.

  AVG should be ok.  Other AV problems even if 'disabled '.

  I'll try to disable settings NIC "unloading" next Monday (it's my wifes computer and I'm sure you can guess the rest).

  Not to be pedantic, but you mention that it would be temporary disabling.  What happens if this does not resolve the problem, what I won't give in now the settings?

  Give you up to a tiny fraction of one percent of time processor, because your host CPU would be checksums compensable package instead of the card NETWORK adapter.  Any difference would be unnoticable on a modern desktop computer.

  If a new NETWORK adapter driver becomes available, you can always try which allows once again to see if the new driver fixes it.  Even if a newer version of the workstation out.

• virtual machine on the host computer has been detected to have a duplicate ip address

  I have seen several threads about this, but they are all either point to one) all resources used or b) firewall issues, and since I have neither, I wanted to see if anyone knows the answer...

  I have 6 servers identical all running the same exact version of ESX Server 3i 3.5.0 build-153875 and 5 of them work perfectly, but the 6th gives the same error as the original poster. It obviously isn't a problem of firewall from the 5 / 6 work very well and I connect to all (and about 15 other servers vmware ESX Server) of my workstation. The server with the question has no installed VMs (don't stay connected long enough to build a) and he passesd all hardware diagnostics I run on it. It has an IP address static, put in place like all other servers and ESX I reinstalled several times.

  Looking at the logs, I see this message: virtual machine on the host has been detected with a duplicate IP address

  How is this possible, is that there is still no VMs on that? Anyone know how to fix this?

  How is this possible, is that there is still no VMs on that? Anyone know how to fix this?

  Not sure why she complains VM, as you didn't tell any virtual machine set up, but define you as static.  Are you sure that you do not use an IP address already in use?

  Disable the ESX host, can you ping the IP?  Something is using this IP address somewhere, so the message can be vague, but something is causing an IP address conflict.

• Cannot ping a virtual machine, except on the host computer.

  I have a host of SuSE, built on a chassis of IBM. It has a link for the failover interface. It has an IP of 10.10.138.196. SM 255.255.255.128. DG 10.10.138.129. I can ping this machine without problem. On that note, I have a virtual machine of SuSE. It has the same mask and gateway with an IP address of 10.10.138.197. It can ping the host (196) and the host can it ping. However, he cannot ping to the gateway by defaut.129. He receives a message Impossible to its own virtual interface. I have installation bridged networking early with no luck.

  I tried to change the DG on the guest a.196. I have installation routes by default, and specific directions to 10.10.138.129 on the host and the guest without success. I talked to a few colleagues and they are not of course either. I need this available, so it can be used for a variety of applications.

  You will not see a virtual NETWORK adapter for bridged interface, only for NAT and the host-only networking. There will be a device/dev/vmnet0, but that is not actually used to fill itself.

  Your problem is that your bridged interface is bound to the wrong card on the host: it must be related to "bond0" not "eth0". You will need to re - run /usr/bin/vmware-config.pl to address which forces all running VMs to be stopped.

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.