I7 quad PC, 12 GB RAM, 64-bit slows down after several click operations

Similar Questions

• Ping.exe takes a lot of computer RAM and everything slows down

  Original title: ping.exe

  Ping.exe takes a lot of computer RAM and everything slows down. I stop the process, but it comes back. How can I remove it permanently?

  Hello
  I suggest that you try to run the computer analysis online and check if this may help:
  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Also, try to perform the clean boot and check if it helps:

  http://support.Microsoft.com/kb/310353

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  It will be useful.

• Tecra 9100 - installed like 512 MB RAM, but it slowed down my computer!

  After much fumbling around trying to install my new 512 MB of RAM, I turned on my computer to find that it starts much more slowly. A message popped up saying 'Memory Module added' and my computer shows 768 MB is installed which is correct, because I already have 256 MB installed in Slot 1.

  So why on Earth is my computer even slower! I bought it to speed up the thing! My computer is slow to start, is less sensitive and much better with just the 256 MB of RAM installed.

  I think I might have damaged the RAM or the Slot 2 because at first, I inserted it incorrectly. They should have a video demo on how to install it because the manual didn't help me that much!

  The RAM is crucial and supports my cell phone because I ran tests to determine what RAM I need.

  Can someone help me please!

  Hello

  Well, it is possible that the new RAM is malfunctioning.

  But have you checked the speed of RAM? How much MhZ is the module supports?

  The Tecra 9100 supports PC2100 512 MB (PA3164U - 1 M 51) module and it runs at 266 MHz.
  If the new module supports a lower speed that the old second module will work also with lower speed.

  Moreover, I would not recommend using modules without name. The performance is bad. Kingston modules are much better.
  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=6183&ft=m&St=3

• Why speedgrade slowly guard eating up more RAM? Why slowing down?

  So, I tried to use the new Speedgrade CC 2015 on my desk with:

  • 4790 K I7
  • GTX 960 (2 GB OF VRAM)
  • 16 GB of RAM (Corsair Vengeance 1600 Mhz)
  • Purple WD 3 to HARD drive
  • Corsair 650W PSU

  I have some Adobe products configured to use up to 12 GB of Ram, while the 4 GB remaining is used to run Win 8.1 and several other background processes (Ref: image provided).
  I realized I still edition speedgrade pantry gradually upward from RAM. I have a 5 min video with several cuts I've linked directly from Premiere Pro for Speedgrade and even a few basic changes later, I think the program is weak and there is a serious mismatch between change values and the changes that appear on the screen. Is there a bottleneck of some sort that I'm missing here? The use of the RAM develops gradually with each additional change. Here a picture after some modifications in speedgrade. Note that I closed Premiere Pro after import via the Direct link.
  

  As a result I can't continue working in speedgrade and must close and restart. But the problem starts again in a few moments. What I'm doing wrong here? Also, is this normal high ram for a 5 min video with barely any changes done in speedgrade?

  There is a memory leak in Sg that strikes some people and seems to have expanded, including YUV Vectorscope, opened. Given the ranking without scopes is so limited that they are stupid, well, that's a problem. They are working on fixing this problem as she can hit hard. Saving & never closing ten minutes is a pain, no? My 32 GB of RAM lasted a little longer... but still would be mounted max and s l o w everything down. Dennis Weinmann has noticed this on another thread here...

  Neil

• ' Spooler Sub System App stopped working and was closed "__MS Vista Home Premium with SP2, 4 GB of RAM & 32 bit OS.

  ' Spooler Sub System App stopped working and was closed ".
  MS Vista Home Premium with SP2, 4 GB of RAM & 32 bit OS

  Hello

  Check chan seen message here - one of the highest.

  fixed spooler subsystem app stopped working
  http://social.technet.Microsoft.com/forums/en/itprovistaprinting/thread/460f297a-dd66-4476-A176-542e1519ca3e

  ===================================

  If the above didn't help:

  Use this method to clear the spooler and then uninstall and reinstall your printer (check with the manufacturer for)
  the latest driver).

  Check Mr. Fixits here and if you use the other methods go back and try again later.

  Problems of print and error - a Mr Fixit of printing
  http://support.Microsoft.com/GP/printing_problems

  Solve printer problems - a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/8c11977e-8244-408f-A036-7978a618d7a21033.mspx

  ------------------------------------------------------
  Logon as administrator

  Start - type in the search box-> COMMAND - control to the top of the list and RIGHT CLICK – RUN AS ADMIN

  You can copy and paste each line except those brackets and press ENTER after each.

  net stop Spooler

  (echo suppression of all print jobs)<-- you="" should="" see="" this="">

  ping localhost n 4 > zero

  del/q %SystemRoot%\system32\spool\printers\*.*

  net start Spooler

  (sound Done!)<-- you="" should="" see="" this="">

  ping localhost n 4 > zero

  Another way
  http://4sysops.com/archives/how-to-cancel-a-print-job-that-hangs-under-Windows-Vista-and-XP/

  Check the print - DELETE/STOP queue all jobs - then right click on the printer - REMOVAL
  http://windowshelp.Microsoft.com/Windows/en-us/help/bb6f81d9-4092-4ac8-9716-2bd008f513e11033.mspx

  If you use Control Panel - Classic - printers

  Try after unplugging your printer if necessary.
  -------------------------------------------------------------

  Also check the spooler print and its dependencies and addictions Service.

  Print Spooler service
  http://www.blackviper.com/WinVista/services/Print_Spooler.htm

  How difficulty Windows Vista print spooler starts do not
  http://www.ehow.com/how_4920100_vista-print-spooler-not-starting.html

  ------------------------------------------------------------

  Check this thread if necessary - to stop and erase the spooler

  http://social.answers.Microsoft.com/forums/en-us/vistaperformance/thread/a15779d6-ac0d-42FD-9Ac2-a1da241ea19f/

  and here
  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/58b54fa9-cf6f-40F7-90b2-8093c6777493

  ------------------------------------------------------
  Clean the General corruption and repair or replace the damaged/missing files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  CheckDisk (chkdsk) runs at startup.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• I have a toshiba laptop (4 GB ram) with Win 7 64 bit. Can I format with 32-bit win7 and after that the 32-bit system reads all the 4 GB of ram?

  I have a toshiba laptop (4 GB ram) with win7 64-bit can I format all the 4 GB of ram with 32 bit win7, and after that can read 32 bit system?

  [Moved from comments]

  Original title: decommissioning

  W

  64-bit can but 32 bit can only use concerts of ~ 3.25.  Why would you want to change (which would require a complete reinstallation including all apps) 32-bit?

• Portege M700 falls down after upgrading to Windows 7 32 bit

  Dear all,

  My portege M700 laptop played most of the reliable time.
  However, it was taken very slow sleep after a few iterations of sleep-wake, taking > 5 min.

  I have now installed Windows 7 32-bit, which works very well. Has no problem with the release of sleep. However, on 1-2 times per day now, I get a message that Explorer crashed and must restart. About once a week, the system crashes completely with a blue screen of windows (without core). Most of the time, in seconds to the time that the screen freezes, I hear the fan switch on at full speed (much faster that it never runs normally) and the case becomes hot enough.

  I installed the latest drivers for 32 bit Windows 7 on the site of Toshiba UK.

  Can someone help me to diagnose the cause of these accidents?

  Thank you very much

  Chris.

  Hello

  It is difficult to say what might cause this behavior strange system.
  But you said something about the hot deal and fans begins to spin faster

  It seems that the internal temperature of laptops increases to a higher level.
  A higher temperature may affect the RAM modules and this could be the reason why the system hangs and does not answer.

  What to say that you should check the Win 7 power management settings.
  There are many options that could decrease the performance of the processor and increase the cooling.
  In addition, you should check if the cooling fans are free of dust obstructed fans might not run properly and this would increase the temperature as well.

  Hope this helps you

• Windows 7 64 bit, start slowing down, the desktop icons and taskbar of loading very slowly since last week!

  so first, I'll start with my system features:

  Reference Dell Xps15z
  Intel Core i7 - 2640M to 2.8 ghz
  NVIDIA GT525M 2 GB
  8 GB RAM
  Windows 7 Home Premium Service Pack 1 64-bit
  Samsung PM830 SSD 2.5 "7 GB 218, 42 GB of free
  My laptop is now just a year and plays well outside some blue screen errors that have been fixed. The question now is time to start being significantly slower, especially the loading of the office. It takes 15 seconds to the password screen, to 45 seconds to reach the office and another 45 seconds to the taskbar, icons and things on the desktop to load. What is unusual is that during this black screen, my mouse is displayed, as well as for Advanced System Care 6 performance monitor (I doubt that this is the problem as I had installed for some time). I did the troubleshooting on mine and removed about half of my program without success. I also checked the health and performance of my SSD with SSD and SSD life and both seem to be very positive. I did not any changes to the Bios because I don't want to reinstall my OS and I'm not really sure on workarounds.
  I tried also to the difficulty of the task of explorer.exe, by checking the value of shell in the registry and it is correct, that it just load slowly at the start and each time I kill and then open it again in the Task Manager. Therefore, I think that my main problem is with explorer.exe loading slowly for some reason, I also removed some desktop icons and taskbar, although I doubt that it makes much difference.
  I've also done many scans with malware bytes pro and hitman pro, there is no virus on my computer.
  I appreciate any help, as it is very inconvenient for my more than 90 seconds start time, when he was about 20 when the laptop was new.
  Thank you very much for your help!
  P.S. I have about 60 GB of games installed on my pc via steam, if it makes a difference to delete some

  When my Windows 7 is slow to start, I do the following:

  Start, then in the search box, type of race. In run, type "msconfig"(sans guillemets), and then click OK. ""
  In the general tab, make sure that selective startup is selected.
  Under Selective startup, clear the check box load startup items.
  Then go to the Startup tab and disable everything except software antivirus and important such as the microsoft. In addition, DO NOT disable any program that you do not recognize.
  This will disable any unnecessary background programs and prevent to launch at startup.
  NOTE: you can still start programs even if they do not start at startup. For example, your favorite game is one of them, and you the disabled. Now, the game does not start at startup, but if you click on the game icon later, it will always start, except maybe a bit slower when it starts. Basically, you are delaying the start of programmes which does not need to start at startup, you move a part of the start-up BACK period. The only programs that you do not disable is programs that actually need to start (like if it starts your computer will blow or something similar).

• Visual C++ 2010 Express on Windows 7 64-bit slows everything

  Hello

  After suffering for a week, I can find no clear response from everyone and decided to seek the help of this community. I am trying to do the work of development using Microsoft Visual C++ 2010 Express. I recorded my Visual C++ so that it works without obvious interruption. When I am trying to build my code in Visual C++ Express, it slows down the normal behavior of my machine. For example, a browser window or a file browser explore (My Computer) takes about 20 seconds to appear after clicking. The volume control bar takes forever to pop up. I followed the process on the Task Manager window, but nothing is abnormal, and memory consumption is well below the red line. More important still, this happens whenever I try to work in C++. Do not do Java (Java obviously has its own virtual machine so everything goes not on a virtual computer died there too; does not affect the machine). The only problem I managed to isolate is probably the 64-bit windows.
  I've been Googling for an acceptable answer but can't find anything. People are formulating opinions ranging from the instruction sets at low altitude on the PC with the ambiguity of high-level code. I don't know what on Earth is wrong. I have core i5, Memory Cache L3, 8 GB of RAM and 500 GB HARD drive. This cannot be a problem of the standard of PC...

  Hi MannaAnam,

  For assistance on this issue, you can post the question in the link below:

  Visual C++ Express Edition
  http://social.msdn.Microsoft.com/forums/en-us/Vsexpressvc/threads

• my pc slows down whenever I want to play a game. has got more ram czec and new nvidia card don't know what else to do. can you help me?

  my computer slows down whenever I want to play a game. GRIP more memory ram and a new nvidia card.dont not know what else to do. can you help me? game comes on and goes back to the desktop wallpaper.

  What games do you play?

  the 3200 + is OOOOLLD and you would be difficult to run whatever be done in recent years at all

  and you get drivers like that who already have your computer or MB, realtek can be obtained from the realtek site

  Since you don't list the exact model of each card, we cannot say whether you are running a GF2 MX or what

  and uninstall the nvidia cp stuff, then run http://www.guru3d.com/category/driversweeper/ to clear what is not respected

• Windows 7 64-bit slow start of blue circle hangs on the network icon in the notification area. Some programs don't load until the problem resolves. stuck at the screen of welcome for 5-10 minutes sometimes.

  Hello world.

  It will be long and windy.

  I have a problem with my ASUS G50VT - X 5.

  im going to write down the details of my question, short first. so if you want you can read my short story on my laptop and I.

  • Slow start.
  • Network at startup initialization problem.
  • Blue circle weighs on my network icon in the taskbar notification for 10 minutes or more. then she disappears with the problem that everything starts to operate correctly.
  • some startup programs do not start until the issue is resolved. (blue circle disappears) i.e. adjustment of splendid colors, services, programs of control really like network connections and things like that but some i can still run.
  • programs that have to do with the network or the internet such as IE or center network to hang until the issue is resolved.
  • Some programs won't load if started up that the problem is solved. for example, microsoft outlook and other things.

  Another thing, I noticed. If I have automatic network connection configuration and the network is in range when I launch firefox I can actually serf the web regardless of the question.

  I'm not the only one having this problem, but solutions that work for some do not work for me. some of the things I've tried to understand.

  • has run msconfig to see if it is one of the start up programs or services is causing the problem. found nothing.
  • run the cmd command, I think that the chkdsk. It digitizes and restores the registers according to me. did not help
  • Used norton. then corrected all the errors found and the questions. did not help.
  • Ran startup recovery tool to fix problems at the beginning. did not help.
  • Booted up my laptop in SafeMode with network. Works very well

  Also, the problem started not with win 7 install I had it on my laptop well before the problem.

  im running Windows 7 Professional 64-bit. as if lately, about a week ago my laptop started to start, slow down and be laggy when the system boots. I have no much attention at first. Since the question does not disappear on its own, I noticed that my network in the notification bar icon has a blue circle probably because its network initialization or loading something that is bound to it something as is. After about 10 minutes the issue resolves itself and everything works fine until I have reboot or restart. also sometimes on occasion I will be stuck to the homescreen for 7-10 minutes.  also if I put my laptop to sleep when I start it it works fine. I think that the time to resolve that issue got longer it is about 10 min now but it used a lot less. at least that's what I recall. In addition, I noticed a few more things. If I left click on the network icon does nothing when normally it will display network connections. If I right click on it displays troubleshooting and Open Network and Sharing Center. Troubleshooting doesn't help and returns nothing. Network and sharing Center is suspended until the problem resolves. in fact, some programs won't load until it the problem goes away as internet explore, network and sharing virtually Center almost everything what has to do with the network and also other programs that require a bit more resources. What else... the kicker is that while the issue is to present the networks I connect to automatically are in fact very well and I have internet, even though the network is still initializing. what I mean is that if I start my portable firefox and launch (cannot use IE because he hangs up) I can go online and the serf of the web.

  Well, I am at a loss and don't know what to do next, except to format and clean install. However, people who did it until the problem was which leads me to believe that this is one of the windows updates may be.

  If someone knows how to fix this problem or can give a kind of constructive contribution, I'm all ears.

  Thanks in advance.

  I also looked in the event viewer and noticed these problems...
  The winlogon notification subscriber took 916 second (s) to handle the notification event (Logon).
  -

  -

  6006

  0

  3

  0

  0

  0 x 80000000000000

  56201

  Application

  Collin-PC

  -

  TermSrv

  916

  Opening of session

  02000000

  and it was lower than...
  Bucket of error, type 0

  Name of the event: ServiceHang

  Answer: No available

  Cabin ID: 0

  Signature of the problem:

  P1: LanmanServer

  P2: srvsvc.dll

  P3: 6.1.7601.17514

  P4: 20

  P5: 2

  P6:

  P7:

  P8:

  P9:

  P10:

  Attached files:

  C:\Windows\Temp\WERBC1D.tmp.WERInternalMetadata.XML

  C:\Windows\Temp\WERBC1E.tmp.HDMP

  C:\Windows\Temp\WERCBA9.tmp.mdmp

  These files are available here:

  C:\ProgramData\Microsoft\Windows\WER\ReportQueue\AppHang_LanmanServer_958bb07ee47f1d58779ce0fb489791f2b7187bdb_cab_0de8cef2

  Symbol of the analysis:

  Recheck for solution: 0

  Report ID: 0de8cd67-d5a8-11e0-a8a7-9ab1f0009500

  Display state: 6

  and below that,.,.

  The winlogon notification subscriber takes a long time to handle the notification event (Logon).

  Hello

  1. Since when are you facing this problem?

  2 have you made changes on the computer before this problem?

  3. do you get any error code or error message while starting?

  I would suggest trying the following methods and check if it helps.

  Method 1:

  If you have not tried the steps in the following Microsoft article, then try to clean boot and check if it helps.

  How to solve the problem by running the clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: Once you have completed troubleshooting, perform the steps in the step 7: to reset the computer as usual.

  Method 2:

  Step 1:

  If the problem persists, you can create a new user account and check what is happening. To create a new user account

  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

  Step 2:

  If the new user account works fine then the old account has been corrupted, you can follow the link given below to fix the corrupted user profile.

  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

  Hope the information is useful.

• Cell calculation is a bit slower

  Hi, I use Acrobat XI Standard to create a form.

  Name of the cell	Cell value
  A1	1
  A2	2
  A3	3
  A4	= A1 + A2 + A3

  For example, if I put 1 in cell A1 and A2 2 and 3 in A3, I want A4 to calculate A1 + A2 + A3 = 1 + 2 + 3 = 6. My problem is, when I put 1 in cell A1, A4 poster 0, when I then put 2 cell A2, A4 shows 1. Then I put 3 in A3, A4 shows 3 which is the sum of 1 + 2 (A1 + A2). The calculation seems to be a bit slower than my entry. So when I complete the entry, A4 shows 3 which should be 6. If I want to make it correct, I need to do another action, like putting 0 into another cell so A4 would calculate A1 + A2 + A3 instead of just A1 + A2.

  It happens to many columns and other columns are fine, I checked the settings and properties in both cells and they are the same, so I don't know how to do.

  My laptop is windows version 1511 10 pro, the CPU is Intel Core i7-5500U CPU @ 2.40 GHz 2.40 GHz. type system is 64-bit, x 64 processor operating system.

  Please let me know how to solve this problem. Thank you.

  This is a typical symptom of a wrong field calculation order. Then in the form of edit mode, select:

  Tasks > other tasks > set field calculation order

  and organize the fields in the logical order.

• Prime Minister cs6 (32-bit) pro found no where on pc after several facilities but cloud doesn't say "installed".

  Please help... first pro (32-bit) cs6 found no where on pc after several facilities but cloud didn't say me "installed".

  Premiere Pro

  There is no such thing... you MUST have a 64-bit computer to install first Pro CS5 and new

• Bridge CC (64-bit) is unable to start the cache even after several time of virtue. Help! So frustrated!

  Bridge CC (64-bit) is unable to start the cache even after several time of virtue. Help! So frustrated!

  Hi julesmom,

  Please reset the Bridge preferences and then try it.

  Measures

  Start Adobe Bridge, and immediately press Ctrl + Alt + Shift (Windows) or command + Option + shift (Mac OS down) until the dialogue box reset settings appears.

  Select all three options - reset preferences, reset Standard Workspaces and all miniature Purge Cache - and then click OK.

  Reference: troubleshooting errors, freezes | Adobe Bridge | Windows, Mac OS

  Let us know if it works.

  Kind regards

  ~ Mohit

• Hello... just asked this, but not sure it sent... new laptop, no cd/dvd player, need to install my design cs6... standard have code # and product series, but the only download link, I found was a bit slow (14 days and count - up - when it expired,)

  Hello... just asked this, but not sure it sent... new laptop, no cd/dvd player, need to install my design cs6... standard have code # and product series, but the only download link, I found was a bit slow (14 days and count - up - when it expired, haha)... hoping someone can help, please and thank you

  You can try with below steps if you want:

  Folder Temp light 1).

  (2) close all running Applications.

  (3) close webistes all opened browser.

  (4)disable the firewall temporarily.

  (5) open only Adobe Web site as it is safe and secure site free of all kind of threats.

  (6) then try to download CS 6 Design Standard and check.

  Note: Though the firewall is disabled. do not open applications, files or even other Web sites.

  Or if you think it is still very slow and would not turn off the firewall , you can try with 3' rd party like download managers: IInternet Download Manager , which is more efficient than the browser built in downloader.