image failure

Similar Questions

• Error messages from backup system «Ox8078014B and Ox80070570»

  When you try to back up my Windows 10 System I get error 'Ox8078014B and Ox80070570' messages and backup fails?  What can I do?

  What was your original system before the upgrade to 7,8,8.1?

  I got 8.1, I had to ride to 8.1 and rerun the original disc of windows with the number of keys licensen orginal about 3 times between each time I have ried to run a restore of the system backup image wouldn't he kept re-run the orginal disjk I'm sinking read the files and they were loading whenever it took over time than before so I know it sis not completely load , then after I tried to the 8.1, he would go to a full backup and a system image restore complete on my external hard drive that you have well connectioned before running any backup or system restore image failure, when I sent to OS10 the first time I tried it, I put the disk in a roll it back to 8.1 revive the disc loaded file restery missing only restored what was need to operstr the computer, and then upgraded to OS 10 ran the file history upward and the image restore system disk WD 2 TB external and before doing that I went to the store windows, they have files for a kit of 5 tools to download OS 10 repair no problems.

  If it will not be restored in windows 7 pro, 8 or 8.1 I'll carry back to people u bought it, you have a faulty drive or a bad hard drive that not having not the windows registry file is AFAIK what elses maybe wrong, but Microsoft won't help

• Getting a Windos 7 Build 7601 non-genuine copy for a Home Premium which has been installed for > a year

  I had a Windows 7 Home Premium operating system installed on a Raid 1 (mirror) configuration for more than a year. Windows 7, I bought it at a major, reliable, computer supplier NCIX.  A few months ago, I bought an Intel SSD drive and cloned on this disc; However, as I was not able to create a system image of this player, I disconnected this drive until I had the time to solve this problem. (What ultimately I did last night)

  Unfortunately, recently my Raid configuration (using the Intel Rapid Storage Technology technology) needed to make a regeneration. While I reboot my system, I was able to log in but inside one minute I had a blue WHITE screen to identify the error to build 7601.

  This environment, the only thing to do, I can manage scheduled to start Task Manager, where I could start a "new task" as cmd.exe , but could not run in mode "elevated command prompt" cmd.

  My user name has administrative privleges but I was unable to properly execute one of the suggestions I found on this topic on the Microsoft site, etc..  For example if I start a new task to the task Mgr, find cmd.exe in the Windows/System32 folder and try to "run as Administrator", I get a message "cannot find D:\Windows\System32\cmd.exe". But if I spend just without the option "Run as Administrator", the cmd function runs but unfortunately not as an administrator.  (Windows is probably showing on D: because of the additional Windows Boot partition that Windows Installer initially created on this drive is C :)

  In the last week or so I tried to save various files of my drives Raided by starting off my SSD drive which is not as recent as the pair Raided.  I didn't really want to re - install Windows 7 and charging/configure various other software I had on the pair Raided.  I can't find pictures of system or to try to fix the Win7 on the pair Raided, the restore points.  I tried a repair feature, without result.

  "Because I was not getting anywhere with the resolution of this ' error 7601" on my records searched, I have attached another drive and clone the SSD him but manually defined a 'disc system reserved' more on the SSD that fixed my "create a system image failures."  I have re-cloned and then to the SSD.

  I just restarted to from the SSD and now get "black background" with a "7601" error After losing my time following various guests/options/suggestions Microsoft who finally suggested that I should buy another copy of Windows software, I've run the MGADiag tool and which one out of this note.  I have full access to a windows environment 'normal' on system SSD... which I did not when starting and connecting to the pair of Raid.

  I just ran the Visual Basic slmgr.vbs with the /ato option.

  It has left me with a background black but deleted the message "not authentic 7601" and declares that "

  Slmgr.vbs /ato C:\Windows\System32>cscript.exe
  Microsoft (R) Windows Script Host Version 5.8
  Copyright (C) Microsoft Corporation. All rights reserved.

  Activation of Windows 7, edition HomePremium (586bc076-c93d - 429 a-afe5-a69fbc644e
  (88)...
  Product activated successfully.

  So I hope to keep it that way and don't revert to an "error of 7601" on a subsequent re-start because I noticed in some THERE IS some THING ELSE other cases 7601 I SHOULD DO HERE?

  This is my exit from the MGADiag tool.  I'm including this here because I could "sort of run" ONCE the MGADiag tool of the pair of Raid, but not as an administrator and could not make a copy, etc... with the exception of pen and paper... and I see that there are a LOT OF SIMILARITIES.

  *********************************************************************************

  Diagnostic report (1.9.0027.0):

  -----------------------------------------

  Validation of Windows data-->

  Validation code: 50

  Code of Validation caching online: 0x0

  Windows product key: *-* - XVKWR - KFGKB-MYCPT

  Windows product key hash: PT0zEORVnXrrm7t9O3ABKxoRAXs =

  Windows product ID: 00359-OEM-8703773-15233

  Windows Product ID Type: 3

  Windows license Type: OEM System Builder

  The Windows OS version: 6.1.7601.2.00010300.1.0.003

  ID: {1358A6E4-2100-4BBC-9128-A83C39B6AB2E} (1)

  Admin: Yes

  TestCab: 0x0

  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002

  Signed by: n/a, hr = 0 x 80070002

  Product name: Windows 7 Home Premium

  Architecture: 0 x 00000009

  Build lab: 7601.win7sp1_gdr.130104 - 1431

  TTS error:

  Validation of diagnosis:

  Resolution state: n/a

  Given Vista WgaER-->

  ThreatID (s): n/a, hr = 0 x 80070002

  Version: N/a, hr = 0 x 80070002

  Windows XP Notifications data-->

  Cached result: n/a, hr = 0 x 80070002

  File: No.

  Version: N/a, hr = 0 x 80070002

  WgaTray.exe signed by: n/a, hr = 0 x 80070002

  WgaLogon.dll signed by: n/a, hr = 0 x 80070002

  OGA Notifications data-->

  Cached result: n/a, hr = 0 x 80070002

  Version: N/a, hr = 0 x 80070002

  OGAExec.exe signed by: n/a, hr = 0 x 80070002

  OGAAddin.dll signed by: n/a, hr = 0 x 80070002

  OGA data-->

  Office status: 100 authentic

  Microsoft Office Home and Student 2007-100 authentic

  OGA Version: N/a, 0 x 80070002

  Signed by: n/a, hr = 0 x 80070002

  Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3

  Data browser-->

  Proxy settings: N/A

  User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)

  Default browser: C:\Program may Explorer\iexplore.exe

  Download signed ActiveX controls: fast

  Download unsigned ActiveX controls: disabled

  Run ActiveX controls and plug-ins: allowed

  Initialize and script ActiveX controls not marked as safe: disabled

  Allow the Internet Explorer Webbrowser control scripts: disabled

  Active scripting: allowed

  Recognized ActiveX controls safe for scripting: allowed

  Analysis of file data-->

  Other data-->

  Office details: {1358A6E4-2100-4BBC-9128-A83C39B6AB2E}1.9.0027.06.1.7601.2.00010300.1.0.003x 64*-*-*-*-MYCPT00359-OEM-8703773-152333S-1-5-21-1350503964-1028441739-1876621095the system manufacturer,System Product NameAmerican Megatrends Inc. 1904 20110815000000.000000 + 00078FD3E07018400FE04090409Time(GMT-08:00) Standard Pacific03100100Microsoft Office home and Student 200712Z0oSK3z6LOYrokskISdOdsrrUJU =81602-926-3148084-682381 57242F264863F3C

  Content Spsys.log: 0 x 80070002

  License data-->

  C:\Windows\system32\slmgr.vbs(1333, 5) Microsoft VBScript runtime error: permission denied

  Windows Activation Technologies-->

  HrOffline: 0x00000000

  HrOnline: 0x00000000

  Beyond: 0 x 0000000000000000

  Event timestamp: 3:22:2013 13:16

  ActiveX: Registered, Version: 7.1.7600.16395

  The admin service: recorded, Version: 7.1.7600.16395

  Output beyond bitmask:

  --> HWID data

  N/a, hr = 0x80070005

  Activation 1.0 data OEM-->

  N/A

  Activation 2.0 data OEM-->

  BIOS valid for OA 2.0: Yes, but no SLIC table

  Windows marker version: N/A

  OEMID and OEMTableID consistent: n/a

  BIOS information:

  ACPI Table name OEMID value OEMTableID value

  APIC                                    ALASKA                                A M I

  FACP                                    ALASKA                                A M I

  HPET                                    ALASKA                                A M I

  MCFG                                 ALASKA                                A M I

  SSDT                                    AMICPU                               PROC

  *********************************************************************

  My output of MGADiag "gradient" of the pair of Raid mode resembles the following. I've highlighted the differences with an arrow<>

  Validation of Windows data-->

  Validation code: 50

  Code of Validation caching online: 0x0

  Windows product key: *-* - XVKWR - KFGKB-MYCPT

  Windows product key hash: PT0zEORVnXrrm7t9O3ABKxoRAXs =

  Windows product ID: 00359-OEM-8703773-15233

  Windows Product ID Type: 3

  Windows license Type: OEM System Builder

  The Windows OS version: 6.1.7601.2.00010300.1.0.003

  ID: {1358A6E4-2100-4BBC-9128-A83C39B6AB2E} (1)<== different="">

  Admin: No.<=== no="" instead="" of="">

  TestCab: 0x0

  LegitcheckControl ActiveX: N/a, hr = 0 x 80070002

  Signed by: n/a, hr = 0 x 80070002

  Product name: Windows 7 Home Premium

  Architecture: 0 x 00000009

  Build lab: 7601.win7sp1_gdr.130104 - 1431

  TTS error:<===  >

  Validation of diagnosis:

  Resolution state: n/a

  LICENSES TAB displays an error message...<>

  Cscript error: can not find script engine "VBScript" script

  'D:\Windows\System32\slmgr.vbs '.

  Tab Office showed the release status showed 100 authentic

  **********************************************************************************************

  If I could do "run as Administrator" access, I think that I could fix it my Win 7 disk Raided. "

  Help...  PLEASE, I BEG YOU.

  Concerning

  Hi Bennett,

  Thanks for posting your question on the Forums of community of Microsoft.
   
  See this link:
  How to activate Windows 7 or Vista manually (activate by phone)
  http://support.Microsoft.com/kb/950929/en-us

  a. Click Start and in the search for box type: slui.exe 4

  b then press the ENTER"" key.

  c. Select your "country" in the list.

  d. choose the option "activate phone".

  e. stay on the phone * do not select/press any option * and wait for a person to help you.

  Clearly state your problem to the support person.

  (f) the person must give you a confirmation ID, copy it down on paper.

  g. Verify that the ID is correct in reading the support person.

  h. Enter the identification number, then click 'Next' to complete the activation process.

  Also refer to this link and check:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/Windows-is-showing-as-not-genuine/cbd43297-0e4d-458C-8487-9168c4cd668d

  Hope it will be useful.

• Is there an advantage to having a backup disk image of Macintosh HD (for MacBook Pro) to ease/speed of recovery after a disk failure rather than using Time Machine to recover?

  I'm trying to understand the best way to prepare for the recovery of a failure in the drive for a MacBook Pro.

  I do not understand the nuances of the time Machine - I know from personal experience that it is a recovery tool great when your existing drive is intact and you're just trying to restore a file.  But what happens if the drive has a hardware failure and needs to be replaced?

  Is there an advantage to take periodic images of Macintosh HD for quick recovery (and then using the incremental backups Time Machine to catch up to the current position).  Or Time Machine may facilitate a recovery in case of failure of the disc just as easily/quickly that will give it to have a separate image backup?

  Thanks in advance for your help.

  YES!.  If you have a clone boot disk, you can either connect it to a MBP or Exchange it with the internal HDD failed and be back in business quickly.  Time machine, as good as is, can take several hours to restore your system, depending on the amount of data.

  For cloning, I recommend Carbon Copy Cloner.  It is not free, but it's worth the price:

  https://Bombich.com/

  I use it in conjunction with Time Machine.  (two backups are better than one)

  Ciao.

• Don't drive HP Pavillion G6 2210SA RED hard failure no bootable image message

  Hello

  I'm sure that the hard drive has failed. I tried reset hard with and without mains. I left the power on and after a while, I get a message saying that the selected boot image is not authenticated. I went into the BIOS, but there is no Diagnostics tool to test the hard drive.

  I'm happy to have another hard drive (if you can confirm that this is the question), but how to install Windows 8 once I have reinstall the hard drive? I can't even find my phone on the support forum and even fewer know about recovering from a hard drive failure.

  Can someone help please? Thank you.

  janner66 wrote:
  

  Very good idea. I'll post on some forums and see if anyone can help. Do I need to know my serial number of Windows 8 to make it work?

  No, the product number is encoded in the BIOS so you only have the recovery disks.

• Z200 lock failure 2239-ME Image - Image of 2240 - unlock ME failure

  Dear reader,

  Whenever I start my HP Z200 I got a black screen first by the following text:

  Failure to lock picture 2239-ME

  Image of 2240-ME unlock failure

  Press F1 to start

  After pressing F1, it starts and starts Windows.

  He started all of a sudden.

  I tried:

  -Check the last update of the BIOS = OK

  -Downloaded the Intel Management Engine Firmware Update utility

  I have installed this Service Pack (SP50543.exe). I tried the update of Windows and back-getting updated, but nothing happened on my screen. Whe or read the Readme file provides information about the computers HP Compaq 8100 Elite?

  -J' called HP on my experiences, but they could not find a solution.

  My configuration:

  -Z200

  -Windows 7 32-bit professional BN

  -39 months, warranty just ended

  Kind regards

  Martin Verkerk

  Hello Skylarking,

  HP has not found another solution.

  Maybe a replacement of the motherboard.

  What I tried and what was very strange: I replaced the CMOS battery and failure was gone!

  I don't understand because you are not espect when the unit is running it may be wrong (or there is a failure with the motherboard).

  For now: thank you very much for your comments!

  Kind regards

  Martin Verkerk

• Communication failure USRP 2952R after loading image

  Background

  I recently started working with the NOR-2952R (X 310) and I'm trying to contact her on the 1 GB NETWORK card on a Linux server.  I am very familiar with the USRP N-210 and I'm looking to use it in a similar way.

  Problem

  My host uses UHD 003.007.001 so when I first performed a uhd_usrp_probe, I got the standard incompatibility message shown below, so I reimagee with the X 310 bit file comes from uhd_images_downloader.  The little-used file was usrp_x310_fpga_HGS.bit.

  Error: RuntimeError: number of firmware compatibility 0x3 WAITED, but had 0x4.0

  After loading the new image, I received x 300 errors of communication/fw as follows:

  [user@host ~] $ / usr/bin/uhd_usrp_probe - addr = 192.168.10.2 args
  
  Linux; GNU C++ version 4.4.7 20120313 (Red Hat 4.4.7 - 4); Boost_104100; UHD_003.007.001 - 0-unknown
  
  UHD error:
  
      x 300 failure communication fw #1
  
      EnvironmentError: IOError: x 300 poke32 fw - answer has expired
  UHD error:
  
      x 300 failure communication fw #1
  
      EnvironmentError: IOError: x 300 peek32 fw - answer has expired

  After a repair this problem for a few hours, I think I have bricked my device and I train using the JTAG interface to reimage the appliance.

  Question

  What is the right image to load for the UHD 003.007.001 driver and how to fix the failures of communication?  My server using a Broadcom NIC and I saw another post, suggesting that users had issues with Realtek NIC.

  Thank you.

  As a follow-up, my camera was indeed bricks by a corrupt charge.  I initially loaded (and subsequently recovered) my camera with the command below.

  [user@host ~] $ sudo/usr/bin/usrp_x3xx_fpga_burner - addr 192.168.10.2 - fpga-path /usr/share/uhd/images/usrp_x310_fpga_HGS.bit

  I was able to retrieve my device via JTAG with the same bit file and persisted in my image with the same command above.

  Go Hoos.

• Application failure and or image opinion what causes this?

  I turned on my computer this morning and I'm now request and image or failure notice like this.    X the application or DLL C:/windows/system32/jytvhi.dll is not a valid image of what's wrong with my computer?   I ran a diagnostic and it says that I have a file broken windows updates, then how can I fix it?

  Hi Johnblackford,

  Seems to be a malware or viruses cleaned your system file, leaving behind traces in the registry.

  You can use CCleaner to clean your registry system for this entry http://www.piriform.com/ccleaner

  Alternative - locate this file in the registry

  Start-> Run Type & -> Regedit-> ok

  Access

  HKEY_CURRENT_USER-> software-> Microsoft-> Windows-> CurrentVersion-> Run

  and

  HKEY_LOCAL_MACHINE-> software-> Microsoft-> Windows-> CurrentVersion-> Run

  Locate and reference pointing to the file 'jytvhi.dll' or 'C:\WINDOWS\System32\jytvhi.dll' path, select, and then delete it.

  Alternative, you can search the registry for "jytvhi.dll" and remove references.

  I hope this helps.

• Failure of System Image recovery

  My dv7 3165dx notebook PC is no longer support Windows 7.  I spent six weeks researching the issue through forums and even contacted HP support by phone.  The first action I took was to back up my files using a SATA cable USB on another computer.  Then I did a system restore.  The restoration process would be to reformat the hard drive, but could never reinstall windows aterwards.  Other research suggests that order the recovery disc for my particular model would settle the matter, so I did.  After trying to boot from the recovery discs, I finally got some error codes that suggested the hard drive has been corrupted and will need to be replaced.  I had 2 it professionals to confirm this suggestion and then explained my story to someone at HP support on the phone and confirm again once I needed a new hard drive.  (corrupted HARD drive is 500 GB)

  Now I have a new herd of 650 GB drive and follow all the instructions supplied with the discs.  I turn on the laptop with the first recovery disc in.  BIOS is configured to boot from the CD/DVD.  System Image Recovery begins, asking if I want to reformat the drive and start the recovery.  The progress bar indicates the restoration of files on hard disk and makes 30% after about 40 minutes, and then a box will appear:

  "Failure of the copy of the file.  Of D:\PRELOAD\BASE19. WIM C:\RM\Image\BASE19. WIM.  Press OK to retry.

  pressing ENTER or ESC takes about 20 to 30 minutes more to get the same box again never exceed 30%.

  I have a new hard drive and HP recovery disc and still not usable laptop.  I have read also several similar topics on similar problems but you have not found a solution that works yet.  I appreciate a lot of help.

  Hello

  You are welcome.

  I've always liked to link to the site to developers for free software, but I agree that the download options are not immediately obvious.  However, as you use a Mac, there is no need for additional software - you can burn the Image file (ISO) of Windows disk as described in he following link.

  http://www.Macinstruct.com/node/390

  Kind regards

  DP - K

• failure to communicate with the image drum?

  My m175nw is only 2 weeks... Everything worked great until I did the Firmware update.  Now, I get the following error and I think I printed only one (1) page since I bought this thing

  10.0004 power error
  10.1004 supply memory error

  There is a failure to communicate with the imaging drum.

  The update of the firmware was "2012-08-27, Version: 20120806, 10.28 M" and the error message

  10.0004 power error
  10.1004 supply memory error

  is the display on the printer control panel.   I was running Windows 7 (64 bit) at the time of installation, but I also have a system dual boot and can run MAC EVALUATE which the same message after restarting the printer.  Even with the computer turned off the M175nw displays the same error message.  As stated earlier, the printer is only 2 weeks, I think that I've printed 2 pages (with no problems) and the above-mentioned error did not appear after the update of the Firmware... I tried a reset to the default settings, but unfortunately that has no effect when the firmware has been updated.

• Failure of the system for Windows 8 image backup

  I downloaded Windows 8 a few days ago. I tried to create a system image to an external drive, Western Digital 500 GB (409 GB free) four times and each time after a few minutes a message said that the backup failed. The backup of the recovery Partition seems end OK every time. The failures occurred after a minute or two in the backup of the C: drive of the OS.

  The external hard drive checked OK. The player has already had an image of the system for Windows 7 which was removed before the backup attempt. Here are 2 messages I received as the backup failed. The other 2 were much the same, I think.

  "There was a failure in the preparation of the backup image of any of the volumes in the backup set. (0X807800C).
  The mounted backup volume is inaccessible. Try the operation again. (0X8078004F)."

  "There was a failure in the preparation of the backup image of any of the volumes in the backup set. (0X807800C).
  The specified drive is not found. (0 X 80780081)"

  Below are the 2 files on the external hard drive after the failure. I guess that the first was the complete recovery Partition backup. I don't know much about this sort of thing.

  7da23344-ab79-11e1-887d-806e6f6e6963.vhdx - 7.61 GB
  7da23345-ab79-11e1-887d-806e6f6e6963.vhdx - 7.00 MB

  Anyone have any ideas on the problem? The software only virus on the PC is Windows Defender that came with the operating system.

  Fifth time is a charm, I suppose. I tried saving image system for the fifth time and successfully completed this time. Nothing has changed on my system or readers.

• Call WebService Imaging of BPEL is a failure

  Hello

  My Env is the last 11g 11.1.1.8.

  I'm calling the Services Web Imaging (http://Host/imagerie/ws/ApplicationService? wsdl) deployed on another Weblogic of Bpel server. When I tried to call this web service with credentials of security he could not because of the issue of access.

  I tried to call the following steps Imaging web service.

  1. Additional Oracle/wss_http_token_client_policy for the Imaging Web service reference.
  2. Add these properties in Composite for the reference as a link below.

  < policyReference URI = "oracle/wss_http_token_client_policy.

  orawsp:category = orawsp:status 'security' = "enabled" / >

  < name = "weblogic.wsee.wsat.transaction.flowOption property"

  Type = "xs: String" much = "false" > SUPPORT < / property >

  < name = "weblogic.wsee.wsat.transaction.version property" type = "xs: String" "

  much = "false" > DEFAULT < / property >

  < property name = "oracle.webservices.auth.username" type = "xs: String" "

  much = 'false' override = "may" > weblogicxz < / property >

  < name = "oracle.webservices.auth.password property" type = "xs: String" "

  much = 'false' override = "may" > welcome111 < / property >

  < property name = "httpBasicUsername" >weblogicxz< / property >

  < property name = "httpBasicPassword" >welcome111< / property >

  
  

  But now all by testing my Bpel workflow my reference fails with error below. Can you please help me to solve this issue.

  < message >

  < input >

  < Invoke1_getApplication_InputVariable >

  < name of part = 'Settings' >

  < getApplication >

  < appNameId >

  < code > < /ID > 2

  < name > CaptureImageApplication < / name >

  < / appNameId >

  < sectionFlags / >

  < / getApplication >

  < / part >

  < / Invoke1_getApplication_InputVariable >

  < / Entry >

  < fault >

  < bpelFault >

  < faultType > 0 < / faultType >

  < remoteFault >

  < name of part = "summary" >

  < Summary > MustUnderstand headers: [{http://schemas.xmlsoap.org/ws/2004/10/wscoor} CoordinationContext] does not include < / summary >

  < / part >

  < name of party 'detail' = >

  < detail > oracle.j2ee.ws.client.jaxws.JRFSOAPFaultException: Client from server SOAP fault: MustUnderstand headers: [{http://schemas.xmlsoap.org/ws/2004/10/wscoor} CoordinationContext] does not include < / details >

  < / part >

  < name of part = "code" >

  < code > {http://schemas.xmlsoap.org/soap/envelope/} MustUnderstand < code >

  < / part >

  < / remoteFault >

  < / bpelFault >

  Hello

  I don't think that it is a failure because of the issue of access, I think that it is a failure because one of the parties is NOT configured to use WS - AT (WS-Atomic Transactions)...

  MustUnderstand headers: [{http://schemas.xmlsoap.org/ws/2004/10/wscoor} CoordinationContext] are not included

  Why did you add it?

  Type = "xs: String" much = "false" > MEDIA

  much = "false" > DEFAULT

  See you soon,.

  Vlad

• CC have reinstalled due to the failure of the system.  When opened in the image space RAW goes yellow spot, with blue background.  I reinstalled without effect.  At the opening, in RAW, the image is restored for future treatment.  Error occurs with both d

  CC have reinstalled due to the failure of the system.  When opened in the image space RAW goes yellow spot, with blue background.  I reinstalled without effect.  At the opening, in RAW, the image is restored for future treatment.  Error occurs with both dng and arw.  Ideas.

  Try the following:

  In the Camera Raw window, press Ctrl + K (Cmd + K on a Mac) to bring up the preferences.

  Uncheck the box processor graphics use.

  If that suits him, update your graphics driver may allow you to work with the checked graphics processor.

• Image processing failure: error code: 1004

  When you export to DropBox of Lighroom I get this error: image processing failure: error code: 1004

  Under which it lists all the images that I export.

  99% of the time the images for export to the correct location and look good. But the error always comes to the top. And every now and then photos are not really exporting.

  Windows 10

  Lightroom Version CC 2015.3

  Thank you!

  Try to reset the preferences of the instructions here file

• Replace the legends of success or failure with images.

  Hello
  
  Can I use legends of success and failure for clickboxes or buttons.
  
  Is it possible to display an image of success or failure in place?
  
  Brian

  Hi Brian

  I saw your post earlier today. Unfortunately (actually fortunately in this case) I was unable to answer, because I was in the middle of the realization of a class of Captivate. At that time, I probably would have advised that it is simply not possible.

  Tonight, after reviewing things again and passing through the messages of today, I almost responded again with a resounding no. Then I suspended and figured it out. That thought, was how these subtitles are really just still images. Where the text is superimposed background images. Then, I remembered that when you select the image used for the background of a legend, a choice appears on the list that allows you to navigate to a desired image. So I tested and here's the deal.

  Double-click the legend of feedback
  Select the text that has been provided and delete
  Click the type of legend drop-down and scroll the selection to the end. You should see .
  Select the item and dialogue should appear immediately. It should contain 'Open' in the title bar.
  Note that this dialog box is programmed so that the images in list in. In BMP format. Don't let this discourage you if your image is in a different format. Perhaps. GIF or. JPG. All you need to do is navigate to the location where your image is, and then in the file name field, type *. GIF or *. JPG and press ENTER to display images of this type.
  Click to select your image and click on the OK button.
  Now, your image must be pulled in the slide, but it seems rather odd. This is because it has been extended to the size of the legend. Do not alarm you. All you have to do is to adjust the size so the image seems appropriate. It is enough to click on one of the corner resize handles and try to make the image as small as possible. You will notice that you cannot resize the tiny image what she really is.

  And there you have it!

  Sincerely, I hope that's what you're looking for and it helps out you. Rick