IMAQdx timeout

Similar Questions

• Error-1074360293 (IMAQdx Timeout) after completing the acquisition for some time

  My vision in LabVIEW application makes several acquisitions and successful treatment but then acquiring (grab) suddenly fails with a timeout error (-1074360293, IMAQdx: timeout). The error does not when acquiring only the images.

  After that the error occurred that no acquisition is possible. Although LabVIEW is closed MAX Returns a time-out error. Only restart helps.

  some details of the material:

  3 controllers FireWire (1394-a)

  3 cameras connected to the first two controllers, one third (total of 7 cameras)

  Mode for all cameras: 1280 x 960 Mono 8 fps 7.50

  The bandwidth for a FireWire controller is sufficient. (Three cameras on a single controller are running without any problem).

  Consume the application memory is short before or after that the error occurs. But I can't find where exactly.

  Until the error occurs a few minutes until one and a half hour pass.

  More details will follow.

  Is there a FireWire or specialist in the vision that can help you?

  Greetings,

  SHB

  Change the driver it seems to fix the problem:

  "Compatible (legacy) 1394 OHCI host controller" (in German: "OHCI - 1394-Hostcontroller (alt) konformer")

  With this pilot test has worked for more than 66 hours without raising an error.

  Some Articles about:

  http://www.RME-audio.de/forum/viewtopic.php?id=9827

  http://www.myvideoproblems.com/ProblemPages/CannotCapture.htm

• IMAQdx timeout with camera JAI multicast

  We have a JAI camera connected to a GigE card, displaying the image in a LabVIEW program, and it has worked reliably for months.  We would now like to save the image for short periods of time as well.  We have added a second computer on the GigE network to capture and save the image with a dedicated software stream.  We put the camera JAI multicast so that both computers receive the same image.  Now, we're getting timeout errors in the LabVIEW program: error-1074360293 to IMAQdx to Image.vi.  Increase the length of the timeout to 10 seconds (default is 5) has not helped.  No idea why IMAQdx does not multicast, but works correctly in unicast?  Y at - it a setting I missed?

  Hi nathand.

  It seems IMAQdx 3.9 added a bug that will leave multicast mode not working correctly (the camera is silently configured for unicast in some cases mode - Interior CAR # 318906). Can you confirm if you use this version, or if you use an earlier version? If you say it works for a little while but fails, I guess it's _not_ this bug.

  Do you know what type of switch you use between the camera and the two PC? If it is a managed switch he may use IGMP snooping to determine which of your interfaces is listening for multicast addresses. It is possible that a bug in implementation of this Protocol switch can cause the association to give up after a while. You may disable this Snooping and either assign manually multicast addresses are transmitted or move it to all ports.

  Eric

• Black screenshot image

  I plugged a USB stick for labview using the IMAQdx. Initially, he would go, but would produce errors of time-out after 5 pictures. Now, I managed to get the cycle to run 50 times, but the picture only comes out as a black screen. What could be causing this and how can I fix?

  I think his problem is resolved in this post:

  http://forums.NI.com/T5/LabVIEW/IMAQdx-timeout/m-p/2823844#M826279

  Guess there is no problem with his camera connectivity. I would ask you to mark it as solved if your problem is solved F.N.

• Prevention of timeout to trigger

  Hi, I use the 1427 OR with a camera NIR Goodrich 640 x 512.  We use an external source to trigger the camera and the time between two pulses of trigger is sometimes longer than the time-out for the camera (I immediately the value 2000 ms).  I would fix rather a delay of 10 seconds for the camera and I was wondering if there was some funciton of that I could call before calling the imaqGrab function to see if the camera has actually aqcuired a picture and was ready to be "seized."  Thank you!

  @FeralPhys:

  I think you can set the timeout much higher. In fact, we have several projects where the expiration time is set to infinity.

  The question is, how do stop you grabbing, while he is indefinitely stuck waiting and you must stop the application. You can do this by making a loop of parallel execution, which close the session IMAQ if stop condition. After the closure of session IMAQ, IMAQ Grab stops with an error (which you can easily manage).

  We use this approach generally with IMAQdx, but I think that it works with the same way IMAQ.

  V

• Unable to send mail, timeout, smtp does not... already for a week does not work.

  Dear Sirs

  all of a sudden I also can't send mails, timeout with the smtp server of my e-mail address, provider's web. of
  Firewall disabled, uninstalled antivirus...
  Server smtp.web.de
  port 587
  STARTTLS
  other ports also does not, any more than ssl
  router may not be the problem, because I work with two different routers in two different apartments, so that now the two of them, all of a sudden does not allow to send mails, seems highly unlikely to me.
  system windows 7 Home premium 64

  Thank you in advance, I'm really tired of playing with her...

  Thank you very much, now after 10 days of work do not now it works again...

  -)

• How to increase the speed of work and avoid the "Server timeouts" with VPN and?

  Hello!

  I am faced with slow work and delays in Thunderbird to my Linux.

  I have 4 accounts (3 are connected via IMAP) and two of them runs very slowly. Fear that every time I see annoying message at end of the period of the server and each message (same old) opens very slowly and sometimes doesn't open.

  It maybe the problem in services postal themselves, or illustrated by the 4th account is Exchange (which work much faster in fact), but I need to manage that somehow. I think I had a fast enough internet connection.

  I know that the server timeout could be increased, but I have not found this option in the settings. I have 31 TB, and all the settings, I found in Google seems to be linked to the old version with the old interfaces. I went to advanced settings, I'm not sure that it's settings and what value it must contain.

  In addition, has something like 'caching 'mail TB? I mean, during the reception of the new letter - it is "cached" locally, so when I try to read - local version is used until "cache" is cleaned. But when I delete or move the letter to another folder - happening also at the level of the server. I think that if TB could sync all mails and store their values locally this will work much faster.

  Thanks for any possible solution to this.

  It seems to me that I found the root cause of the problem)

  Problem is not in TB, but in these 2 mail services itself. They work poorly when vpn works.

  Will address this issue for messaging services.

• The server request timeout expired pending request from the browser. How to fix?

  After having successfully reached www.foxnews.com, trying to branch to one of the stories in the viewfinder and receive "Request Timeout".
  The server has expired pending request from the browser.

  Reference #2.5cab3c41.1399773250.0
  Using Internet Explorer I don't have this problem. How can I do this time-out to go

  You can try the following steps in case of problems with web pages:

  You can reload webpages and ignore the cache to refresh potentially stale or corrupt.

  • Hold down the SHIFT key and click the Reload button
  • Press 'Ctrl + F5' or 'Ctrl + Shift + R' (Windows, Linux)
  • Press 'Command + shift + R' (Mac)

  Clear the cache and cookies only from Web sites that are causing problems.

  "Clear the Cache":

  • Firefox/tools > Options > advanced > network > content caching Web: 'clear now '.

  'Delete Cookies' sites causing problems:

  • Firefox/tools > Options > privacy > "Use the custom settings for history" > Cookies: "show the Cookies".

  Start Firefox in Safe Mode to check if one of the extensions (Firefox/tools > Modules > Extensions) or if hardware acceleration is the cause of the problem.

  • Put yourself in the DEFAULT theme: Firefox/tools > Modules > appearance
  • Do NOT click on the reset button on the startup window Mode safe
  • https://support.Mozilla.org/KB/safe+mode
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• Stop the connection timeouts occur - want the page wait

  I run several tab that monitor various tools. These pages will refresh. Pages must wait each other finish before you can start.

  In version 28 it was beautiful. The page just wait indefinitely and kicked in a previous page after doing its thing.

  Now in version 29 he comes back with a message "connection timed out" after a few minutes.

  I adjusted

  Network.http.connection - timeout
  Network.http.pipelining.Read - timeout

  for values but the problem still occurs. Any thoughts on how I can find the FF28 behavior?

  Try setting the http.response.timeout parameter. In the version 28, it had not been established. Version 29, it is located at 300 (5 minutes). Should help to move on to something much larger.

  See this blog entry:

  http://morgb.blogspot.com/2014/05/Firefox-29-and-HTTP-response-timeout.html

• Set URL timeout

  How to set the timeout for connecting to a URL?

  The time-out period BEFORE Firefox reports 'not found '.

  There is no setting in Firefox to do this. Modify a TCP/IP parameter in the registry.

  http://drewthaler.blogspot.com/2005/09/changing-DNS-query-timeout-in-Windows.html

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DNSQueryTimeouts
  Multiple string: '0 1 2 2 4 8'-> "4 8 8 16 32 0".

• 39L4333DG will not connect to laptop WiDi - timeout

  I'm tempted to try to get the WiDi to work.
  First of all: TV is updated to the latest version via autoupdate.
  Laptop is 2nd generation than i7 2675 WiDi compatible with all the latest drivers.

  I can detect the TV, I can try to connect. Laptop request PIN, the PIN is displayed on the TV.
  TV says then connects, so it is portable. After a while (like 30 seconds) the TV said that there was a timeout. Laptop keeps trying to connect for a few seconds more and that's it.

  Any idea what the problem might be?

  > Laptop is 2nd generation than i7 2675 WiDi compatible with all the latest drivers.

  First, please check if computer laptop supports WLan Intel WiDi appropriate card.
  Where it is, you must update the Intel WiDi software.

  Here, on this page from Intel, you will find the required software from Intel:
  http://www.Intel.com/support/wireless/wtech/IWD/sb/CS-031109.htm

  You must update: Intel®, Intel® Wireless Driver driver.
  Need to install the latest version of the software Intel WiDi and other Intel WiDi Widget

  I hope this helps!

• GSS108E firmware upgrade timeout - no solution using arp

  Hello

  already dug through the community and has found some clues but neither worked.

  After trying to update the firmware of 1.0.0.0 to 1.0.0.1 (after 30% a TFTP timeout occurred), the switch no longer responds. I tried to reboot several times but no way. I use the latest version of the utility 2.3.5 on Windows 10 x 64 and he finds the switch but now the update fails always after 30 seconds to prepare. I tried the arp suggested orders, but that no longer works. Also using the command netsh in Windows did not help.

  Are there other solutions? I also tried to connect directly separate full network, but also without success. Any help would be welcome avoid sending the rear switch.

  Thanks and best rehards,

  Shotokan

  I had the same problem. Finally solved.

  Open an administrator command prompt.

  Run:

  netsh interface ipv4 add neighbors 'Ethernet' 192.168.0.3 a0-63-91-89-1f-da

  Substitute the name of your connection to the network 10 'Ethernet' windows, 192.168.0.3 with the IP address of your GSS108E and a0-63-91-89-1f-da with the MAC address of your GSS108E.

  It will be useful.

  Best regards

  Lage

• Timeout/screen lock.

  My screen doesn't timeout at least that I have to manually turn it off via the locking button or fingerprints. If my screen is locked, but I turn on the screen without unlocking, he'll sleep in no matter what time I specify.

  I played with change in the duration of the timer, which stands currently at 30 seconds. I also have attentive display and the display of notifcation of bike on.

  None of the above items interfere with screen timeout? Is this everything works as it should and I need to adapt to manually turn it off on my screen? Is there something else I should try? Am I missing something really obvious (I feel that I dug through every possible setting on this thing)?

  These thoughts struck me as well. I tried every permutation of the options associated with the screen on and stop that I could find.

  However, I advanced and formatted the SD card and made the FDR. I don't know what caused the problem, but I know who took care of her.

• Center solutions guaranteed Lenovo Server Timeout

  I have a lenovo x 1 carbon. for some reason when I click on the lenovo Solution Center in the botton left said guaranteed: the server timeout. Can anyone help me please with this. Thank you

  
  

• Gateway Timeout problem

  With the help of a MacBook Pro 13' (mid-2012) El Capitan (Version 10.11.1). running

  Usually living abroad, came home last night and managed to connect my computer to the internet WiFi and my parents very well. Could access any Web site, ran perfectly. This morning I started having a problem where I can open only a small number of websites (Facebook, Youtube, Google, Apple, Wikipedia), another Web site gives me a ' Gateway Timeout: unable to connect to the remote host " message, even large reputable (NYT, etc.)."

  Here are the facts:

  • MacBook connects to the WiFi
  • MacBook restarted, the problem persisted
  • Reset the router (FRITZ!) 6360 Box cable, German provider is Unitymedia)-online everything has worked again for about 2 minutes, and then the problem comes back
  • All other computers/phones in the House has no problem, can access any Web site
  • Connected my MacBook to the Ether, has worked well. Yet once unplugged and tried WiFi problem returned. Ethernet plugged back in (with WiFi off), now, even the ethernet gives me the same problem
  • Software antiVirus Sophos's active and firewall settings and Web Protection were not yet activated (no idea why)
  • First time this question has occurred (connected to this dozens of times network and worked very well, but with the Mavericks) and has produced at night - everything worked fine yesterday and I am not aware of having made changes to anything.

  Found a thread with a person having a similar problem on another forum of support, but in his case, all its devices had the question so that, in our House, everything works but my MacBook. So I doubt that it is a problem with the provider or router.

  Any help would be greatly appreciated!

  AntiVirus software is Sophos.

  Uninstall completely and evaluate the results.

  Use the Remove Sophos Anti-virus program. It will be installed in the folder Applications on your Mac, unless you have moved or deleted. In this case, follow the instructions in uninstalling here: https://www.sophos.com/support/knowledgebase/122710.aspx. Beware that the effectiveness of the uninstall program is poor, a typical feature of garbage software.