Injector POE 10 SX20 and tactile

Similar Questions

• What ports must be used between SX20 and Intouch?

  Hello.

  I'm a junior engineer of telepresence,

  I face to make matching SX20 and Intouch. They have the same subnet mask and even G/w.

  with this configuration, I had things qurious.

  Question,

  1. in the event that they must have the same mask subnet and the same G/W? If so, why?

  2. which ports to use when pair SX20 and Intouch?

  3. how to pass the NAT H.323 mode

  (I know what WE / OFF mode and also how it works, but I did not understand the Auto mode, there is no document on this subject)

  This is just my thinking I hope I'm wrong.

  I'm afriad that Auto mode automatically calculrate the audit of public or non-public of logical IP subnet internal,

  After that, decide Tochange source ip or keep when H.323 call.

  If that, what users have public IP addresses and use them as private with the exception of a few ip for security, IPs

  and they use for NAT 1:1 or PAT to use internet. So how do they check it's private or public.

  Sorry for the reading of inconvient it, it isn't my mother tongue. and I wish the goodness of the expert.

  1. in the event that they must have the same mask subnet and the same G/W? If so, why?

  No, inTouch able to pair with the codec of subnet different until properly configured gateway IP address.

  2. which ports to use when pair SX20 and Intouch?

  SSH

  3. how to pass the NAT H.323 mode

  Please see the https://supportforums.cisco.com/message/3794585#3794585 which had the same discussion.

• Cisco SX20 and device 10 "touchscreen

  Hello

  I would like to know if the device touch 10 "(CTS-CTRL-DV10 =) is now supported by SX20."

  Kind regards

  Ivan

  Hello, Ivan.

  The SX20 Cisco should support the touch device 10. Visit this link for reference:

  http://www.Cisco.com/c/en/us/products/collateral/collaboration-endpoints...

  Moreover, it is for your SX20 and touch 10 existing?

  Let me know if you have other concerns or by email ([email protected] / * /) me directly. Kind regards.

• SX20 and link ISDN with TC6

  Hi guys,.

  I recently upgraded a SX20 and link ISDN to the new TC6 and after the upgrade, I can't make ISDN call.

  I can see and manage the ISDN link from the SX20 configuration web page, but the status of the ISDN connection is: error, SIP not saved.

  I use H323 network and I don't use SIP between SX20 and ISDN link and with the old version, I could receive and make calls. Now when I try to dial the ISDN using the new interface TC6 endpoint indicates that it does not find the ISDN link.

  Thank you for your help,

  Adrian

  Hi Adrien, Valentine's day.  Theres something happens with outgoing enabled on the link and the Codec for this, and we have two CDETS opened on them.  There are always SIP service is enabled on the Codec with link and link itself.  Codec uses IPV6 local links for the link itself.  Even if the sip xstatus on the codec has its inactive etc, the codec message still SIP REGISTER to the device registration link.  Link runs a FWD SIP process that handles the request.  Sorta like a mini SIP registrar if you want.  Codec will send the message to REGISTER using link-local IPV6 address.  Example of message is less than 200 Ok.

  77582.64 SipPacket PacketDump: Proto: SIP, name: REGISTER sip: [0000::000:0000:0000:cd39]: 15070 SIP/2.0, Direction: outgoing, RemoteAddress: [0000::000:0000:0000:cd39]: 15070, GroupEntity: b27d07c1f5f298c492db68040b320ca6, time: 77582634 content:!

  77582.64 SipPacket REGISTER sip: [0000::000:0000:0000:cd39]: 15070 SIP/2.0

  77582.64 SipPacket Via: SIP/2.0/TLS [fe80::250:60ff:fe83:c52a]: 5061 branch; = z9hG4bK45a7681a50ebbdc5b98e2f91bff6b438.1; rport

  77582.64 SipPacket Call-ID: b27d07c1f5f298c492db68040b320ca6

  77582.64 SipPacket CSeq: 47083 REGISTRY

  77582.64 SipPacket Contact:

  «': 5061; transport = tls >; + sip.instance =»

  77582.64 SipPacket of:; tag = 116a994ac2281c72

  77582.64 SipPacket to:

  77582.64 SipPacket Max-Forwards: 70

  Road to SipPacket 77582.64:

  77582.64 SipPacket allow: INVITE, ACK, CANCEL, BYE, update, INFO, OPTIONS, CONSULT, INFORM

  77582.64 SipPacket User-Agent: TANDBERG/518 (TC6.0.0.876266)

  77582.64 SipPacket expires: 3600

  77582.64 SipPacket authorization: Digest-nonce = "d9605a7da8be22af8c0e7f52b3de4a5f5125fcd3", domain = "MARCIE", qop is auth, username = "djkvvknn", uri is "sip: [0000::000:0000:0000:cd39]"

  ", response ="3b27b753cb9bcf38cc2431b767bce643", algorithm is MD5, nc = 00000002, cnonce ="84addca2a68f6c5f9b657a94653a4bae"

  77582.64 SipPacket supported: replaces, timer, 100rel, gruu, way, way out

  77582.64 SipPacket Content-Length: 0

  77582.64 SipPacket

  77582.64 SipPacket >!

  -----------------------------------------------------------------------------------------------

  77582.65 SipPacket SIP/2.0 200 OK

  77582.65 SipPacket Via: SIP/2.0/TLS [fe80::250:60ff:fe83:c52a]: 5061 branch; = z9hG4bK45a7681a50ebbdc5b98e2f91bff6b438.1; rport = 41246; receipts = 0000::000:0000:0000:c52a

  77582.65 SipPacket Call-ID: b27d07c1f5f298c492db68040b320ca6

  77582.65 SipPacket CSeq: 47083 REGISTRY

  77582.65 SipPacket of:; tag = 116a994ac2281c72

  77582.65 SipPacket to:; tag = e84d13204776ebc2

  77582.65 SipPacket server: fwd

  77582.65 SipPacket Contact:; (+ sip.instance =""

  77582.65 SipPacket Content-Length: 0

  77582.65 SipPacket

  77582.65 SipPacket >!

  -------------------------------------------------

  I removed my own addresses, so you get the picture here.

  It is the same for the link.  Link will send REGISTRY as well to himself.

  Even if your using H320 as outgoing Protocol call, messaging between the codec and the liaison unit is still SIP as the outgoing call is still SIP of the codec for the link even if you chose H320.

  You can see all happening all by running: Journal ctx sippacket debug 9 and connect the output to see the messaging back and forth between devices.  This is why the Service SIP on the codec cannot be disabled.

  The outgoing enabled on both devices and it records not as what Adrian has met is odd. So the question has been filed and is under investigation.

  CSCue57128 - SIP in a strange state connecting to link ISDN (Codec)

  CSCue73049 - outbound SIP on ISDN link activation causes lose her registration (link)

  These are new, so the visibility may not be there yet.

  If you see a problem with the link is not not able to register, check to see if outgoing SIP are enabled on the link.  If so, turn it off and start.

  Do the same on the codec as well.  Disable outgoing SIP and restart the computer.  There may be some cases, you do not see this, as the investigation continues with the bug above two ID's

  I hope this helps.

  VR

  Patrick

• SX20 and sharing of presentations

  Hi all

  I have a few questions about how the SX20 sharing presentations - the installation program will be as follows:-2 offices of each with the following:

  Installed SX20 and a single screen

  input video via HDMI and entry of presentation (laptop) through the VDI-I have

  WAN is tbd based on the required BW

  With a video call in progress, when a presentation is launched for a while, this effect may have a split two showing - what is the end of the screen with the video and the presentation receive?

  Can the end manipulate their display (they receive 2 video stream), or is it a single video stream based on what sends the originating end?

  What is the requirement of BW coming out at the end of starting (it is the sum of the video and the presentation of the flow)?

  Thank you!

  End receives two separate video streams, and you should be able to switch between different layouts on far - end to change the on-screen display.

  Bandwidth call will be always lower than the default bandwidth allocated by placing the call. When the presentation is shared, unit automatically adjusts the bandwidth and the proportion in which the bandwidth gets divided between the presentation and the main power is defined by the configuration. By default, it is 5:5 (1:1).

  Hope that answers your query.

  BR,

  PS

• SX20 and SX10 recommended for small Display built-in speakers using conference rooms

  Hello

  IM planning to deploy a few small rooms of meeting using SX20 and SX10 codecs, I was wondering if someone could give me a few key points to consider:

  1. display recommendation, beautiful built-in speakers, low delay (goog with codec echo cancellation performance), I want to use a 60-70 inch Led TV (not yet defined which brand and model), I would like to receive feedback on beautiful poster with nice audio performance and echo cancellation performance according to your experience.

  2. What are the disadvantages of using SX20 and SX10 bigger meeting room maybe 10 or 12 people?

  3. when to use an external microphone? or when is recommended to only use the internal mic?

  Thanks in advance for your help.

  Best regards, have a nice day!

  1. Pretty much no matter what modern screen should work - different people will have different ideas on the question of whether the speakers are all good, you must listen to a few yourself and make up your community what you think is "better".  Echo cancellation can be changed manually on the codec to adapt the display if necessary (rather than leave it on "auto" which, put in our facilities, has caused more trouble than it's worth).
  2. The main disadvantage of using the SX10 or the least expensive of the range of the SX20s, is the camera and zoom.  In a larger room, you won't get a good closer with a camera 2.5 x.  I would say for a larger room, you look at the 12 x cameras.
  3. As a general rule - use additional microphones when you can't get someone in a radius of 3 m one of the other pickups.  So in a larger room, you may need to much.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Power off SX20 with tactility and touchscreen

  Hello

  is it posible to power off of the SX20 codec through the touch screen? I just saw the option pending, but I can't find how to turn off the power.

  Furthermore, how can I set the sensitivity of the touch?, now when the codec is the sleep option, when someone is near the touch screen of this change online without touching.

  concerning

  Hi Filiberto,

  No, the SX20 cannot be turned off through the touch screen.

  You can reduce the sensitivity of the touch by turning on the resilience of the EMC mode.  To do, look on the Touch under settings, administrator (and connect), EMC resilience and set on IT.

  Note: Your question might be better placed in the section of forums where these devices are more actively discussed as in the section on IP Video telepresence , you posted in-I would say, if the above has not answered your query, you move your discussion there.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• Cisco Telepresence SX20 and Touch 8 Configuration after paired

  Hello

  I successfully connected and combined the SX20 Cisco's Telepresence and Cisco Telepresence Touch 8. Before using the 8 key, we used the remote control instead. As a result, I have two questions about this.

  1. as far as I know, when I use the 8 key, the remote control cannot be used. Is it possible to use both of them?

  2. How can I change the background of my SX20 touch 8? Previously, the remote I can easily choose the background for my SX20. But after pairing with Touch 8, background in my SX20 become a blue large clock. I really want to have a different background but cannot find the way how to change.

  Any help would be appreciated.

  Thank you.

  Sincerely,

  Bagus Hanindhito

  After you connect the 8 Touch, you can still use the remote control, you will need to put on the SX20:

  SystemUnit MenuType experimental configuration: full

  I think that the standard background when using a touchscreen device is what you see, blue with large clock.  However, after the MenuType return in full which will give you the full OSD which is used with the remote and not that of the button, you may be able to change the background then.

• List of remote calls SX20 and green call button implemented recent

  Hello

  I'm currently looking for a show where I'm trying to simplify as much as possible for the users and with a distance Sx20 workflow when you press the green call button it immediately brings to mind a recent calls list. Is there anyway to not immediately set up this list?

  I was talking to users who are certain that there was a time when the SX20 has not brought to the top of the list by hitting the green button on the remote control. I was wondering if anyone here could remember?

  Thank you

  I remember he was always like that, I did a quick search of bug and even through the release notes and see no mention of a change in this behavior.  The SX20 appeared with TC5 software, looking at the User Guide of at the time, they talk the Green Telephone button is "place a call", so it makes sense that it would be a shortcut to open the list of recent calls.

• Key question Qosmio X 770 - 107 - FN and tactile

  Toshiba Forum Dear members,

  I am writing this new thread because I have a serious problem with my Qosmio X 770 - 107.

  I bought it in 2014 of an electronics store famous here in Greece.
  The first problem was the little battery life. It has a duration of one hour when you surf on the internet and for about 10 to 30 minutes when playing games. I've changed lots of time settings but nothing has changed.
  Then I went to the store again once, where they found a problem with the battery and they changed it.

  However the same thing happening. Then I changed the battery 2 times as well as the laptop and the charge of cable during the year. The third model, I had the same problem. After a month I lived some problems with blue screens and the fn keys did not work.
  I formatted and the problem with blue screens has been fixed.

  Today, I always have the same laptop and the fn keys do not work. I tried reinstalling the drivers but nothing has changed. In addition, the touch button for the lighting of the keypad does not work and when I touch it the sound is muted.

  My question is if anyone has had the same problems or similar to ones I have and if I can do something to change this model with another or receive my refund.

  Here, I see that I sent emails many times to Toshiba, but they have not responded.
  I also sent my laptop Toshiba official service in Greece, but they do not solve my problems.

  Please answer as soon as possible

  Thanks in advance

  Kind regards
  Xenophon

  I formatted and the problem with blue screens has been fixed.

  BSOD problems are mainly related to software problems... Updated MS as well as conflicts between different applications can cause the BSOD... so its always advisable to get the device back to factory settings to get rid of system conflicts.

  Today, I always have the same laptop and the fn keys do not work. I tried reinstalling the drivers but nothing has changed. In addition, the touch button for the lighting of the keypad does not work and when I touch it the sound is muted.

  I guess that you always use the Windows 7 system.
  As I said, due to updates, it can happen that the system registry and the FN key utility would be confused to the top...

  The FN keys are controlled by Toshiba Value added Package as well as the Flash Cards Support utility
  That's why I recommend you to uninstall these two tools. Then restart the laptop. To clean the registry (you can use CCleaner utility). After that, restart the laptop once more and then start the installation of the package of added value and utility to Support Flash Cards

  In addition I recommend you check this interesting Toshiba document that explains all the software pre-installed on different Toshiba laptops:
  https://support.Toshiba.com/support/...tentId=3368363

  You can also check help utility of Toshiba... and Toshiba button support that allows to configure the touch buttons...

  You asked for the money back guarantee...
  Well, I've never read this laptop computer manufacturer could repay... in my opinion it should be cleared up with a dealer... but laptops are covered by the standard warranty one year and in case of hardware problems, the Toshiba ASP should fix the problems...

• Re: Lenovo Ideapad U410 and tactile U410 broken / hinge

  I, too, had the same problem who are users in this thread. I have a U410 bought in spring 2014. There was a pause in the hinge and the screen is separate from the cover. I have never dropped the computer, this question came a day after the general, daily use. I have attached photos of the issue for others to reference to.

  EDIT 11/17: Moved to the front of the thread for the purpose of climbing. Amy_Lenovo

  
  

• Injector power 802.3af compliant?

  I have a power injector (Cisco AIR-PWRINJ3) and I wonder if it is part of the 802.3af food standards.   I'm working on

  to power a device non-cisco (give the camera) and for some reason it is not powered by the power injector.  Any ideas?

  No, AIR-PWRINJ3 injector is not compatible 802.3af.  It was developed before the standard so it is based on the POE before Cisco standard being ratified.

• The iPad has Pro 9.7 "tactile 3D?

  I can't say if the new Pro 9.7 "iPad Touch 3D. Below is the only reference that I found him, and it seems that it is just talk about the iPhone 6 s. thoughts?

  

  Non-contact 3D on iPad 9.7 Pro or 12.9

  From this link and give your opinion on (at least) http://arstechnica.com/apple/2016/03/the-9-7-inch-ipad-pro-review-what-makes-som t-pro-any way /

  "But lacking the sensor faster TouchID and tactile 3D, two characteristics that always have not showed up anyway outside the 6s."

• Hello to all I just upgraded for Iphone 6 seconds more and the 3D touch does not work on some things... What am I doing wrong?

  I just upgraded to the new Iphone 6 s more and tactile 3D on everything works expect applications on the home screen when I long press she made sure you

  can move the apps autour with x, but does not have the menu of dialogue that its supposed to come... what I do wrong... the 3D touch is enabled in settings so have no idea... anyone know thanks...

  What applications you try to press and hold on? To bring up the menu, you need to use more pressure. Simply hold down the icon with a light touch will make the icons wiggle with the X to remove the apps.

• How repair my iphone 6s hung in camera I can't able to access on the other and I can't able to swtich offf if sleep button the tank please help me

  I took a few pictures without unlocking my iphone 6 s after that he stuck behind closed doors himself and tactile assitive works but can't go to the home page in my laptop, I tried to change my sleep the mobile tank button that works also not I'm not what to do. Please help me solve this problem.

  Try resetting your device. This will not erase your data stored on that device.

  • Press and hold the sleep/wake button
  • Press and hold the Home button
  • Press and hold both buttons until the display turns off and on again with the Apple logo on the subject.

  Alternatively, you can go to settings - general - reset - Reset all settings

  If that doesn't work, restore your device to factory settings. Please note that this will delete the data on your device.

  Take a look this Apple Support article: use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support